Fujitsu T1000 User manual

Page is loading ...

SPARC

®

Enterprise T1000 Server

Installation Guide

Manual Code : C120-E383-01EN

Part No. 875-4021-10

April 2007

FUJITSU LIMITED provided technical input and review on portions of this material.

Sun Microsystems, Inc. and Fujitsu Limited each own or control intellectual property rights relating to products and technology described in

this document, and such products, technology and this document are protected by copyright laws, patents and other intellectual property laws

and international treaties. The intellectual property rights of Sun Microsystems, Inc. and Fujitsu Limited in such products, technology and this

document include, without limitation, one or more of the United States patents listed at http://www.sun.com/patents and one or more

additional patents or patent applications in the United States or other countries.

This document and the product and technology to which it pertains are distributed under licenses restricting their use, copying, distribution,

and decompilation. No part of such product or technology, or of this document, may be reproduced in any form by any means without prior

written authorization of Fujitsu Limited and Sun Microsystems, Inc., and their applicable licensors, if any. The furnishing of this document to

you does not give you any rights or licenses, express or implied, with respect to the product or technology to which it pertains, and this

document does not contain or represent any commitment of any kind on the part of Fujitsu Limited or Sun Microsystems, Inc., or any afﬁliate of

either of them.

This document and the product and technology described in this document may incorporate third-party intellectual property copyrighted by

and/or licensed from suppliers to Fujitsu Limited and/or Sun Microsystems, Inc., including software and font technology.

Per the terms of the GPL or LGPL, a copy of the source code governed by the GPL or LGPL, as applicable, is available upon request by the End

User. Please contact Fujitsu Limited or Sun Microsystems, Inc.

This distribution may include materials developed by third parties.

Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark

in the U.S. and in other countries, exclusively licensed through X/Open Company, Ltd.

Sun, Sun Microsystems, the Sun logo, Java, Netra, Solaris, Sun StorEdge, docs.sun.com, OpenBoot, SunVTS, Sun Fire, SunSolve, CoolThreads,

J2EE, and Sun are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries.

Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited.

All SPARC trademarks are used under license and are registered trademarks of SPARC International, Inc. in the U.S. and other countries.

Products bearing SPARC trademarks are based upon architecture developed by Sun Microsystems, Inc.

SPARC64 is a trademark of SPARC International, Inc., used under license by Fujitsu Microelectronics, Inc. and Fujitsu Limited

.

The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges

the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun

holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN

LOOK GUIs and otherwise comply with Sun’s written license agreements.

United States Government Rights - Commercial use. U.S. Government users are subject to the standard government user license agreements of

Sun Microsystems, Inc. and Fujitsu Limited and the applicable provisions of the FAR and its supplements.

Disclaimer: The only warranties granted by Fujitsu Limited, Sun Microsystems, Inc. or any afﬁliate of either of them in connection with this

document or any product or technology described herein are those expressly set forth in the license agreement pursuant to which the product

or technology is provided. EXCEPT AS EXPRESSLY SET FORTH IN SUCH AGREEMENT, FUJITSU LIMITED, SUN MICROSYSTEMS, INC.

AND THEIR AFFILIATES MAKE NO REPRESENTATIONS OR WARRANTIES OF ANY KIND (EXPRESS OR IMPLIED) REGARDING SUCH

PRODUCT OR TECHNOLOGY OR THIS DOCUMENT, WHICH ARE ALL PROVIDED AS IS, AND ALL EXPRESS OR IMPLIED

CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE

EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID. Unless otherwise expressly set forth in such agreement, to the

extent allowed by applicable law, in no event shall Fujitsu Limited, Sun Microsystems, Inc. or any of their afﬁliates have any liability to any

third party under any legal theory for any loss of revenues or proﬁts, loss of use or data, or business interruptions, or for any indirect, special,

incidental or consequential damages, even if advised of the possibility of such damages.

DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,

INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT,

ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.

Page is loading ...

v

Contents

Preface xv

1. Preparing for Installation 1

Server Overview 2

Tools Needed 2

Optional Components 3

Installation Overview 3

Slide Rail Assembly Notes 5

Cable Management Notes 7

Data Port and Cabling Notes 8

Port Locations 8

Cabling Notes 8

Safety Precautions 9

2. Installing the Server 11

Rackmount Kit 11

Installing the Server in a Rack 12

▼ To Install the Mounting Brackets 12

▼ To Install the Slide Rails 15

▼ To Install the Server in the Rack 19

vi SPARC Enterprise T1000 Server Installation Guide • April 2007

▼ To Install the Cable Management Bracket 20

Removing the Server From the Rack for Service 21

Connecting the Server Cables 21

▼ To Connect the SC Serial Management Port 22

▼ To Connect the SC Network Management Port 22

▼ To Connect the Ethernet Network Cables 23

TTYA Serial Port 23

▼ To Connect the AC Power Cable to the Server 23

3. Powering On the System 25

Powering On the Server for the First Time 25

Power On Overview 25

System Console 25

ALOM CMT System Controller 26

Passwords 26

▼ To Power On the System for the First Time 27

Logging In To the ALOM CMT System Controller 29

▼ To Log In To the System Controller Using the Serial Management Port 29

▼ To Log In To the System Controller Using the Network Management

Port 30

▼ To Configure the System Controller Network Management Port 31

▼ To Reset the System Controller 34

Using the ALOM CMT System Controller for Common Operations 35

▼ To Initiate the Power On Sequence 36

▼ To Connect to the System Console 36

▼ To Perform a Normal System Initialization 37

Booting the Solaris Operating System 39

▼ To Boot the Solaris Operating System 39

▼ (Optional) To Reset the System 40

Contents vii

▼ To Power Cycle the System 40

A. Updating the Server Firmware 43

Flash Image Overview 43

Updating the Firmware 43

▼ To Update the Firmware 44

B. Selecting a Boot Device 47

Connecting the Network Interface to the Network 47

▼ To Connect the Network Interface to the Network 47

C. Configuring the Network Management Port 49

Configuring the System Controller Network Manager Port 49

▼ To Configure the System Controller Network Management Port 49

Index 53

viii SPARC Enterprise T1000 Server Installation Guide • April 2007

ix

Figures

FIGURE 1-1 Server 2

FIGURE 1-2 Slide Rail Assembly 5

FIGURE 1-3 Mounting Bracket Locks 6

FIGURE 1-4 Cable Management Bracket 7

FIGURE 1-5 Locations of Ports and Connectors on the Rear Panel 8

FIGURE 2-1 Unlocking the Slide Rail Assembly 12

FIGURE 2-2 Mounting Bracket Release Button 13

FIGURE 2-3 Attaching a Mounting Bracket to the Chassis 14

FIGURE 2-4 Captive Screws on the Slide Rail 15

FIGURE 2-5 Using the Extension Bracket 16

FIGURE 2-6 Mounting the Slide Rail 17

FIGURE 2-7 Using the Slide Rail Spacing Tool to Adjust the Distance Between the Slide Rails 18

FIGURE 2-8 Mounting the Chassis on the Slide Rails 20

FIGURE 2-9 Rear Panel Connectors 21

FIGURE 2-10 System Controller Serial and Network Ports, Rear of Chassis 22

FIGURE 2-11 Serial Port (TTYA) 23

FIGURE 3-1 AC Connector 27

x SPARC Enterprise T1000 Server Installation Guide • April 2007

xi

Tables

TABLE 1-1 Ethernet Connection Transfer Rates 9

TABLE 3-1 Server Device List 38

xii SPARC Enterprise T1000 Server Installation Guide • April 2007

xiii

Code Samples

CODE EXAMPLE 3-1 Boot Sequence Example 28

CODE EXAMPLE 3-2 Example of Normal System Initialization Output 37

CODE EXAMPLE 3-3 Example of Server Boot from Disk 0 39

CODE EXAMPLE A-1 Typical Boot Sequence Following Firmware Update 45

xiv SPARC Enterprise T1000 Server Installation Guide • April 2007

xv

Preface

This guide provides instructions, background information, and reference material to

help you install the SPARC Enterprise T1000 Server.

Instructions for installation in the document assume that a system administrator is

experienced with the Solaris

™ Operating System (Solaris OS).

Note – All internal components must be installed by qualified service technicians only.

FOR SAFE OPERATION

This manual contains important information regarding the use and handling of this product.

Read this manual thoroughly. Pay special attention to the section “FOR SAFE

OPERATION” on page xv Use the product according to the instructions and information

available in this manual. Keep this manual handy for further reference.

Fujitsu makes every effort to prevent users and bystanders from being injured or from

suffering damage to their property. Use the product according to this manual.

xvi SPARC Enterprise T1000 Server Installation Guide • April 2007

Structure and Contents of This Manual

This manual is organized as described below:

■ CHAPTER 1 Preparing for Installation

Provides an overview of the SPARC Enterprise T1000 Server installation

process.

■ CHAPTER 2 Installing the Server

Provides instructions for installing the SPARC Enterprise T1000 Server into a

rack.

■ CHAPTER 3 Powering On the System

Provides instructions for configuring and powering on the server, and for

installing additional software.

■ APPENDIX A Updating the Server Firmware

Provides instructions for updating the system controller firmware and the host

firmware.

■ APPENDIX B Selecting a Boot Device

Provides instructions for selecting a boot device.

■ APPENDIX C Configuring the Network Management Port

Provides configuration instructions for servers that use an earlier version of

firmware than system firmware 6.2.

■ INDEX

Provides keywords and corresponding reference page numbers so that the

reader can easily search for items in this manual as necessary.

Related Documentation

The latest versions of all the SPARC Enterprise Series manuals are available at the

following Web sites:

Global Site

http://www.fujitsu.com/sparcenterprise/manual/

Japanese Site

Preface xvii

http://primeserver.fujitsu.com/sparcenterprise/manual/

Note – Product Notes are available on the website only. Please check for the recent update

on your product.

■ Manuals included on the Enhanced Support Facility CD-ROM disk

■ Remote maintenance service

Title Description Manual Code

SPARC Enterprise T1000 Server Product

Notes

Information about the latest product

updates and issues

C120-E381

SPARC Enterprise T1000 Server Site

Planning Guide

Server specifications for site

planning

C120-H018

SPARC Enterprise T1000 Server Getting

Started Guide

Information about where to find

documentation to get your system

installed and running quickly

C120-E379

SPARC Enterprise T1000 Server

Overview

Provides an overview of the features

of this server

C120-E380

SPARC Enterprise T1000 Server Service

Manual

How to run diagnostics to

troubleshoot the server, and how to

remove and replace parts in the

server

C120-E384

SPARC Enterprise T1000 Server System

Administration Guide

How to perform administrative tasks

that are specific to this server

C120-E385

Advanced Lights out Management

(ALOM) CMT v1.x Guide

How to use the Advanced Lights

Out Manager (ALOM) software

C120-E386

SPARC Enterprise T1000 Server Safety

and Compliance Guide

Safety and compliance information

about this server

C120-E382

Title Manual Code

Enhanced Support Facility User's Guide for REMCS C112-B067

xviii SPARC Enterprise T1000 Server Installation Guide • April 2007

Using UNIX Commands

This document might not contain information about basic UNIX® commands and

procedures such as shutting down the system, booting the system, and configuring

devices. Refer to the following for this information:

■ Software documentation that you received with your system

■ Solaris™ Operating System documentation, which is at:

http://docs.sun.com

Text Conventions

This manual uses the following fonts and symbols to express specific types of

information.

* The settings on your browser might differ from these settings.

Typeface* Meaning Example

AaBbCc123 The names of commands, files and

directories; on-screen computer

output

Edit your.login file.

Use ls -a to list all files.

% You have mail.

AaBbCc123 What you type, when contrasted

with on-screen computer output

% su

Password:

AaBbCc123 Book titles, new words or

terms, words to be

emphasized.

Replace command-line

variables with real names or

values.

Read Chapter 6 in the User’s

Guide.

These are called class options.

You must be superuser to do

this.

To delete a file, type

rm

filename.

Preface xix

Prompt Notations

The following prompt notations are used in this manual.

Conventions for Alert Messages

This manual uses the following conventions to show alert messages, which are

intended to prevent injury to the user or bystanders as well as property damage, and

important messages that are useful to the user.

Warning – This indicates a hazardous situation that could result in death or serious

personal injury (potential hazard) if the user does not perform the procedure correctly

Caution – This indicates a hazardous situation that could result in minor or moderate

personal injury if the user does not perform the procedure correctly. This signal also

indicates that damage to the product or other property may occur if the user does not perform

the procedure correctly.

Tip – This indicates information that could help the user to use the product more

effectively.

Shell Prompt Notations

C shell machine-name%

C shell superuser machine-name#

Bourne shell and Korn shell $

Bourne shell and Korn shell and Korn shell superuser #

xx SPARC Enterprise T1000 Server Installation Guide • April 2007

Alert messages in the text

An alert message in the text consists of a signal indicating an alert level followed by

an alert statement. Alert messages are indented to distinguish them from regular

text. Also, a space of one line precedes and follows an alert statement.

Caution – The following tasks regarding this product and the optional products provided

from Fujitsu should only be performed by a certified service engineer. Users must not

perform these tasks. Incorrect operation of these tasks may cause malfunction.

■ Unpacking optional adapters and such packages delivered to the users

Also, important alert messages are shown in “Important Alert Messages” on

page xx.

Notes on Safety

Important Alert Messages

This manual provides the following important alert signals:

Caution – This indicates a hazardous situation could result in minor or moderate

personal injury if the user does not perform the procedure correctly. This signal also

indicates that damage to the product or other property may occur if the user does

not perform the procedure correctly.

Task Warning

Installation Electric shock

There is a potential for electric shock if the server and related equipment

are not properly grounded.

Damage

Deploy the antitilt bar on the rack before beginning an installation.

Preface xxi

Product Handling

Maintenance

Warning – Certain tasks in this manual should only be performed by a certified

service engineer. User must not perform these tasks. Incorrect operation of these

tasks may cause electric shock, injury, or fire.

■ Installation and reinstallation of all components, and initial settings

■ Removal of front, rear, or side covers

■ Mounting/de-mounting of optional internal devices

■ Plugging or unplugging of external interface cards

■ Maintenance and inspections (repairing, and regular diagnosis and maintenance)

Caution – The following tasks regarding this product and the optional products

provided from Fujitsu should only be performed by a certified service engineer.

Users must not perform these tasks. Incorrect operation of these tasks may cause

malfunction.

■ Unpacking optional adapters and such packages delivered to the users

■ Plugging or unplugging of external interface cards

Remodeling/Rebuilding

Caution – Do not make mechanical or electrical modifications to the equipment.

Using this product after modifying or reproducing by overhaul may cause

unexpected injury or damage to the property of the user or bystanders.

xxii SPARC Enterprise T1000 Server Installation Guide • April 2007

Alert Labels

The followings are labels attached to this product:

■ Never peel off the labels.

■ The following labels provide information to the users of this product.

Sample of SPARC Enterprise T1000

Page is loading ...

Fujitsu T1000 User manual

Fujitsu T1000 User manual

Related papers

Other documents