CNB BM4267NL/BM4267PL Owner's manual

CNB
Brand
CNB
Model
BM4267NL/BM4267PL
Category
Security camera accessories
Type
Owner's manual
8. Menu Format 9. Menu Format Table
OWNER'S MANUAL
Before operating the camera, confirm that you have the right
camera model and proper power voltage.
In order to help you understand this manual, we'll introduce
our model's description.
Thank you for purchasing this COLOR VIDEO CAMERA.
If you have trouble operating your camera, refer to the following table.
If the guidelines do not enable you to solve the problem, contact an
authorized technician.
Problem Solutions
Nothing appears on
the screen.
The image on the
screen is dim.
The image on the
screen is dark.
The camera is not
working properly,
and the surface of
the camera is hot.
The image on the
screen flickers.
• Check that the power cord and line connection
between the camera and monitor are fixed properly.
• Check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
• Is lens stained with dirt? Clean your lens with soft,
clean cloth.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change
the camera position.
• Adjust the lens focus properly.
• Adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75/ Hi-z
properly. (refer to page 10)
• Check that you have properly connected the camera
to an appropriate power source.
(refer to page 11)
• Is the camera facing to direct sunlight or fluoresent
lighting? Change the camera position.
Precautions
Composition
Features
Name and Function of Each Parts
Installation
Remote Controller Operation
On-Screen Display
Menu Format
Menu Format Table
Communication Protocol
Troubleshooting
Specifications
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
5
6
7
8
10
14
16
18
19
20
21
22
CAUTION!
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Explanation of two Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of un-insulated
"dangerous voltage" within the product's
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance-(servicing) instructions in the
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE
ON THE BOTTOM OF THE SYSTEM.
"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THE UNIT TO RAIN OR MOISTURE"
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
literature accompanying the appliance.
3
COLOR VIDEO CAMERA
2
Weatherproof Zoom
5
COLOR VIDEO CAMERA
4
Weatherproof Zoom
7
COLOR VIDEO CAMERA
6
Weatherproof Zoom
1110
Weatherproof Zoom
13
COLOR VIDEO CAMERA
12
Weatherproof Zoom
15
COLOR VIDEO CAMERA
14
Weatherproof Zoom
19
COLOR VIDEO CAMERA
18
Weatherproof Zoom
21
COLOR VIDEO CAMERA
20
Weatherproof Zoom
23
COLOR VIDEO CAMERA
22
Weatherproof Zoom
9
COLOR VIDEO CAMERA
8
Weatherproof Zoom
17
COLOR VIDEO CAMERA
16
Weatherproof Zoom
COLOR ZOOM CAMERA SERIES
with DAY & NIGHT
INFORMATION
This equipment has been tested and found to comply with limits for a
Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at their own expense.
WARNING
The manufacturer could void the user's authority to operate the
equipment.
CAUTION - To prevent electric shock and risk of fire hazards:
Do NOT use power sources except for that specified.
This installation should be made by a qualified service person
and should abide to all local codes.
P/N : 3810-0102B
(Ver.0703E)
Color Zoom Camera Series
Digital Zoom Camera Series
Design and specifications
are subject to
change without notice.
DSS
DSS
Weatherproof
Day & Night Color Camera
Weatherproof
Day & Night Color Camera
Digital Slow Shutter
• Electronic Iris
Electronic iris shutter is automatically controlled at the speed of
1/60 ~ 1/10,000sec (NTSC models),
1/50 ~ 1/10,000sec (PAL models).
• Remote Control through RS-485 (Pelco-D)
Remote control operations are possible though RS-485 interface for
focus and zoom control. In addition, the unit lets you command
white balance and exposure manually using RS-485 interface.
• Heater
Depends on internal temperature, it operates automatically.
- Heater ON : under 10C
• High Sensitivity (Digital Slow Shutter)
Digital Slow Shutter is a function which enhances camera's sensitivity
electronically. When DAY/NIGHT mode is Auto, it automatically judges
whether it is day or night. Color images are provided in Day mode
and B/W images in Night mode. DSS setting value is fixed to 2 fields
of integration and twice the brightness in Night mode.
• High Resolution
The horizontal resolution of 480 TV lines can be achieved by
using a high density CCD having effective 410K(NTSC) pixels, which
provides clean, noiseless and reliable pictures.
• Built-in Power Zoom Lens
Subjects can be magnified up to 220 times with 22x optical zoom
and 10x digital zoom.
3. Features
Do use the camera under conditions where temperatures are within
-10C to 45C. Especially be careful for ventilation under high temperature.
(with heater : -30C ~ 45C)
Do not install the camera in extreme temperature conditions.
Do not install or use the camera in an environment where the
humidity is high.
It can cause the image quality to be poor.
Do not install the camera under unstable lighting conditions.
Severe lighting change or flicker can cause the camera to work improperly.
Never use the camera close to a gas or oil leak.
It can cause malfunctions to occur.
Do not disassemble the camera.
There are no user-serviceable parts inside it.
It can cause malfunctions to occur.
Do not drop the camera or subject them to physical shocks.
Never keep the camera face to strong light directly.
It can damage CCD.
Note
When this camera is installed near wireless communication
devices that emits strong electromagnetic field, irregularity
such as noise on the monitor may appear.
1. Precautions
2. Composition . Dimensions(mm)
11. Troubleshooting. Contents
. User Information
Sunvisor
Bracket Supporter
Wall Mount Bracket
Base Adapter
L-Wrench
L-Torx Wrench
Service Monitor Cable
Owner's Manual
BNC Cable
4. Name and Function of Each Parts 7. On-Screen Display
Fixing Bolt for Sunvisor:
You can unfasten the bolt in order to fix mounting bracket above.
Photo Sensor
Sunvisor:
To reduce direct sunlight and protect the camera unit from rain
or snow in outdoor.
Front Body
Base Adapter
Base Adapter Fixing Bolt
Wall Mount Bracket
Bracket Supporter
Rear Body
Mounting Bracket Fixing Bolt:
Fix the camera main body to
bracket by wrench bolt.
•
P
o
w
e
r
f
u
l
Z
o
o
m
i
n
g
F
u
n
c
t
i
o
n
M
a
x
.
2
2
0
x
Z
o
o
m
(
2
2
x
O
p
t
i
c
a
l
/
1
0
x
D
i
g
i
t
a
l
)
5. Installation
Cable the VIDEO out to the monitor video in jack.
Assembling the sunvisor and the bracket. Assembling the bracket supporter
Weatherproof
IR LED Camera
Monitor
Intermediate
Video Receiver
End monitor
• As the connecting method varies with the instruments, refer to the
manual supplied with the instrument.
• Set the 75/ Hi-Z selection switch as shown below if you have an
intermediate device.
• Connect the cable after power is turned off.
Weatherproof
IR LED Camera
Connecting to Monitor
The OSD (On Screen Display) is as follows:
Explanation of the On-Screen Display
Camera Installation Camera Installation
#
3
#
4
Hex Scoket Bolt
(1EA)
Base Adapter
Fixing Bolt
(4EA)
Mounting Bracket
Fixing Bolt
(1EA)
Weatherproof
Zoom Camera
Connecting to Power Supply
- The wire is non-polarized.
- Use AC 24V power source or DC 12V power source.
. AC 24V / DC 12V Power
Black
Yellow
Service Connector
(Extra Video Out Connector)
This camera system includes a service connector that outputs
extra camera video signal. Use it at the installation site to set up
the field of view and focus the camera.
MENU Button
Used to access OSD menu mode or escape menu from mode.
TELE/WIDE Buttons
Used to choose the desired menu item.
It also moves the cursor up or down in the menu screen.
NEAR/FAR Buttons
Used to change the parameter of the selected menu item.
It also moves the cursor the left of right in the menu screen.
. Rear Body
#
1
#
2
#
3
#
4
#
5
#
6
Line ColorNo. Function
#1 RED DC12V/AC24V(H)
ORANGE GND/AC24V(N)
#3 BLACK GND
(
VIDEO
)
YELLOW VIDEO OUT
#5
#2
#4
#6
GREEN RS-485 (+)
BROWN RS-485 (
-
)
VIDEO TELE
WIDE
NEAR FAR
MENU
6. Remote Controller Operation
Receiver
Remote Control
1 2 3 4
Power
DC 12V, 500mA
RS-485 Signal
- White Terminal :
- Black Terminal :
Camera Selection
- After camera connects with receiver,
firstly check camera I.D.
Menu
(
PROG
)
: Shows / Hides Menu.
Moves up and down items.
(
TELE
)
:
(
WIDE
)
:
- Press camera I.D. number(1
~
39 buttons)
on the top of wireless remote controller.
Caution : Usually camera I.D. number
are selected from No.1 to No.39.
over I.D. No.40, you will have a use limit.
- Initial camera I.D. number is set up No.0
when it takes out of manufacturer's warehouse.
Example: ZOOM IN
I.D. No.5: Press 5 +
<
TELE
>
I.D. No.15: Press
<F1>
+ 5 +
<
TELE
>
I.D. No.24: Press
<F2>
+ 4 +
<
TELE
>
I.D. No.34: Press
<F3>
+ 4 +
<
TELE
>
Set data for the selected items.
(
NEAR
)
:
(
FAR
)
:
F1
NEAR
FAR
FOCUS
F3
WIDE
F2
TELE
ZOOM
AUTO
SEQ PAN
PROG
A
7
4
1
6
9
A
0
8
5
32
The remote controller is optional item.
Cable Connection (Pelco-D/ RS-485)
Receiver &
Remote Control
Pelco-D Keyboard
DVR System
Signal (RS-485)
FUNCTION OSD Format DESCRIPTION
1
2
3
4
Focus Mode
Mirror Mode
Back Light
WBC Mode
5
Shutter
Speed
Non display
Non display
Non display
Non display
Normal shutter (NTSC:1/60 PAL:1/50)
8 variable.
7
Wait Mode
Wait
Indicates the camera stand-by mode.
until the camera power turns ON.
8.1
Sharpness
Adjustment
Mode Display
8.2
Brightness
Adjustment
Mode Display
8
Zoom
Display
x22
:
Optical Zoom only mode
x44
:
Digital Zoom x 2 mode
x220
:
Digital Zoom x 10 mode
6
Camera ID
After input the identification number to each camera,
Multi-point control is available. (000~255)
Automatic focus mode
Manual focus mode
No screen inverted
Screen is inverted to the left or right
Back Light compensation off
Back Light compensation mode
White Balance AUTO
Push Auto White Balance: In this mode
"Menu key" pressed, the white point traced
automatically (PWB Auto Mode), "Menu Key"
released, the white point preserved currently
(PWB Manual Mode).
Non display
1 / 125
1 / 10000
x18
x10
SHP
X10000 ID 255
WAIT
X132
1 2 3 4 5 6
7
8
4. WBC(White Balance Control) Display
See Page 17.
6. Camera ID Display
See Page 17.
5. Shutter Speed
Use to select the shutter speed.
7. Wait Mode
Indicates the camera stand-by mode
until the camera power turns on.
8. Example of Zoom, Brightness,
Sharpness Display
See Page 17.
2. Mirror
When IMAGE MIRROR is ON state. The
image is displayed in the opposite direction.
The appear during the mirror mode.
1. Focus
The appear during the focus manual
mode.
3. Back light Display
In case the excessive light is behind the
center object, it is necessary to prevent
the center object from too much
darkness. Turn the BACK LIGHT ON,
then the center object is not influenced
by the back light.
MENU
7 ZOOM START
8 ZOOM STOP
9 BRIGHTNESS
10 SHARPNESS
11 FOCUS
12 PROTOCOL
13 INIT SET
END
1
220
48
10
AUTO
DEF
ON
NO
NAME FUNCTION
1 BACKLIGHT
Use to select BLC mode.
OFF >ON
2
5 SHUTTER
Use to select the shutter speed 8 steps.
NORMAL(NTSC:1/60, PAL:1/50),1/125,1/250,---,1/10000
7 ZOOM START
Use to change the zoom start position.
8 ZOOM STOP
Use to change the zoom stop position.
9 BRIGHTNESS
Use to change the brightness of scene (0~48).
10 SHARPNESS
Use to change the contour of scene (0~15).
11 FOCUS
. AUTO : Set the focus mode to Auto mode.
. PUSH AUTO : Set the focus mode to Push Auto mode.
12 PROTOCOL
. DEF : Default
. P / D : Pelco-D
13 INIT SET
Set the initial mode ON, the changed data are renewed.
Reset the data to its shipping condition.
6 CAMERA ID
To connect a large number of camera, identification
number can be assigned to each camera control easily.
(OFF, 1-255 : total number of ID is 256)
CAUTION : Set the ID number of camera, then
the ID number is displayed continuously.
3
4 WB CONTROL
. AUTO : Maintain best color condition by controlling
the change of color automatically.
WB Range 2800 K ~ 8000 K
.
PUSH AUTO(PWB) :
Can find White Balance exactly
in case precise WB maintenance
is needed under any environment.
--Turn the AUTO mode, WB acts automatically.
--Turn the PUSH AUTO mode, WB doesn't act.
SLOW SHUTTER
Use under very low light condition for full color
surveillance.
OFF >FLD2 > >FLD128
DAY & NIGHT
Use under low light condition for continuous
surveillance.
Auto >ON >OFF
Power OnFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x88
BYTE 4
0x00
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
Power OffFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x08
BYTE 4
0x00
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
Pelco D StopFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x00
BYTE 4
0x00
BYTE 5 BYTE 6 BYTE 7
Checksum
Menu On / OffFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x40
BYTE 4
0x00
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
Focus FarFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x00
BYTE 4
0x80
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
Focus NearFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x01
BYTE 4
0x00
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
Zoom WideFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x00
BYTE 4
0x40
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
Zoom TeleFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x00
BYTE 4
0x20
BYTE 5
0x00
BYTE 6
0x00
BYTE 7
Checksum
PELCO "D" Byte Format
Command Message
-RS-485,2400bps,1 Start bit,8 data bits,1 stop bit,no parity
Menu On / OffFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x00
BYTE 4
0x23
BYTE 5
0x00
BYTE 6
0x5F
BYTE 7
Checksum
Menu On / OffFunction
MSG
BYTE 1
0xFF
BYTE 2
CamID
BYTE 3
0x00
BYTE 4
0x03
BYTE 5
0x00
BYTE 6
0x62
BYTE 7
Checksum
Pelco Keyboard (95+ PATTERN)
V/D Keyboard (Set Preset + 98)
Don't care
10. Communication Protocol
12. Specficications
PALNTSCSignal System
Scanning System
Horizontal Scanning Frequency
Vertical Scanning Frequency
Pick-up Device
Total Pixels
Effective Pixels
Horizontal Resolution
S/N Ratio
Lens
Minimum Illumination
(30IRE)
Synchronization
Signal Output
Operating Temperature
Storage Temperature
Power
Consumption
Dimensions (WxHxD)
Weight
2 : 1 Interlace
15.734 kHz 15.625kHz
59.94 Hz 50 Hz
1/4 Inch SONY Super HAD CCD / EX-View CCD
811(H) x 508(V) 410K 795(H) x 596(V) 470K
768(H) x 494(V) 380K 752(H) x 582(V) 440K
480 TV lines
More than 48dB (AGC off)
22x Zoom Video AF
(F1.6(W), F3.7(T) f = 3.9~85.8mm)
1 Lux (Color) ,
0.001 Lux (DSS 128 FLD)
Internal
1Vp-p Composite Output with 75 Terminated
-10~+45 / -30~+45 (with Heater)
-20~+65
AC 24V (24~28V) / DC 12V (DC 9V~15V)
Max. 8W (AC 24V) / 9.6W (DC 12V)
110.8 x 218.6 x 325.7 mm
Approx 1.6kg
On-Screen Display
OSD
OSD
220
x Zoom
/
TELE / WIDE
Move up and down
using the TELE/
WIDE button.
Can be changed
using the /
button.
MENU
1 BACKLIGHT
2 SLOW SHUTTER
3 DAY / NIGHT
4 WB CONTROL
5 SHUTTER
6 CAMERA
OFF
FLD24
OFF
AUTO
1/10000
123
O
W
NER
'
S
M
A
NU
A
L
C
O
L
O
R
Z
O
O
M
C
A
M
E
R
A
S
E
R
I
E
S
w
i
t
h
DA
Y
&
NI
G
H
T
D
S
S
D
S
S
W
ea
t
h
er
p
r
o
o
f
Day
&
N
i
g
h
t
Co
l
o
r
Cam
e
r
a
W
ea
t
h
er
p
r
o
o
f
Day
&
N
i
g
h
t
Co
l
o
r
Cam
e
r
a
D
i
g
i
t
a
l
S
l
o
w
S
h
u
t
t
e
r
•
P
o
w
e
r
f
u
l
Z
o
o
m
i
n
g
F
u
n
c
t
i
o
n
M
a
x
.
2
2
0
x
Z
o
o
m
(
2
2
x
O
p
t
i
c
a
l
/
1
0
x
D
i
g
i
t
a
l
)
O
n
-
S
c
r
e
e
n
D
i
s
p
l
a
y
O
SD
O
SD
2
2
0
x
Z
o
o
m
  • Page 1 1

CNB BM4267NL/BM4267PL Owner's manual

CNB
Brand
CNB
Model
BM4267NL/BM4267PL
Category
Security camera accessories
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents