Metra Dash kit Installation guide

Metra
Brand
Metra
Model
Dash kit
Category
Car kits
Type
Installation guide
METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
APPLICATIONS
1-800-221-0932
metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-7611
WIRING & ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-7552 - Nissan harness 2010-up
Antenna Adapter:
• 40-NI12 - Nissan antenna adapter 2010-up
Panel Removal Tool • Phillips Screwdriver • Socket Wrench
TOOLS REQUIRED
Nissan Rogue 2011-up
99-7611
B CA
• A) Radio Housing • B) Radio Housing Brackets • C) DDIN Trim Plate
KIT FEATURES
KIT COMPONENTS
• ISO DIN head unit provision with pocket
• DDIN head unit provisions
Table of Contents
Dash Disassembly
– Nissan Rogue 2011-up 3
Kit Assembly
– ISO DIN head unit provision with pocket 4
– DDIN head unit provisions 5
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
99-7611
Caution
Metra recommends disconnecting the negative battery terminal before beginning any
installation. All accessories, switches, and especially air bag indicator lights must be
plugged in before reconnecting the battery or cycling the ignition.
*NOTE: Refer also to the instructions included with the aftermarket radio.
1. If equipped with center speaker: Unclip
and remove the grille then remove (4)
Phillips screws to remove the speaker.
(Figure A)
2. Unclip and remove the panel below the
radio including the a/c controls.
(Figure B)
3. Unclip the radio trim including the a/c
vents then unplug the hazard switch
and remove the panel. (Figure C)
4. Remove (4) Phillips screws securing
the radio. (Figure D)
Continued on next page
3
Dash Disassembly
99-7611
(Figure A)
(Figure B)
(Figure D)
(Figure C)
4
Kit Assembly 99-7611
1. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2. Snap the radio housing brackets to the
radio housing. (Figure A)
3. Slide the head unit into the radio
opening (from behind) and secure
with the screws supplied with the unit.
(Figure B)
4. Reassemble dash in reverse order of
disassembly.
ISO DIN head unit provision with pocket
(Figure A)
(Figure B)
5
Kit Assembly 99-7611
1. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
2. Mount the radio housing brackets to
the sides of the double DIN radio using
screws supplied with the double DIN
radio. (Figure A)
3. Place the DDIN trim plate on the front of
the DDIN radio. (Figure B)
4. Reassemble dash in reverse order
of disassembly.
DDIN head unit provisions
(Figure A)
(Figure B)
Notes
Notes
METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932
metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-7611
REV. 8/08/11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Metra Dash kit Installation guide

Metra
Brand
Metra
Model
Dash kit
Category
Car kits
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents