Rode VideoMic User manual

VideoMic
Rode
Brand
Rode
Model
VideoMic
Category
Microphones
Type
User manual

This manual is also suitable for

8
0
H
z
VideoMic
TM
Parts Guide
Mic Controls
quickstart
guide
VideoMic
TM
www.rodemic.com
1. Foam windshield
2. Camera shoe mount
3. Battery cover
4. PAD switch (inside battery compartment)
warranty.rodemic.com/videomic
Scan the QR code to
register now, or visit
Don’t FORGET
to register for your
FREE ten year warranty!
The RØDE VideoMic
TM
features an integrated
shock mount based on Rycote
®
Lyre
®
technology.
Constructed from a single piece of hard-wearing
thermoplastic, the Lyre
®
provides superior acoustic
suspension to traditional elastic solutions,
and will never wear out, sag or snap.
RØDE SOUNDBOOTH
now for Broadcast mics
Hear and compare RØDE microphones
at www.rodemic.com/soundbooth or on your iPad
®
5. LED power indicator
6. Power and HPF switch
7. Integrated Rycote
®
Lyre
®
suspension
8. 3.5mm dual mono output cable
The High Pass Filter (HPF ) is a low frequency cut-off setting, which you can use
to remove rumble, camera noise or other low frequency noise while recording.
Mic ON
using High Pass Filter
Mic ON
Flat setting
Battery OFF
Mic mute
6
7
8
LED power
indicator
028_952_1_Videomic_Quickstart.indd 1028_952_1_Videomic_Quickstart.indd 1 17/12/2012 8:45:19 AM17/12/2012 8:45:19 AM
0
d
B
-
10
d
B
-
20
d
B
The LED power indicator next to the
On/Off switch will turn red when the
battery is running low. The mic will
work for approximately one hour once
the red indicator is lit, however with
reduced performance.
1. Turn the tightening ring counter-
clockwise to loosen the camera shoe
connection, before attaching to camera.
Securing the cable will
eliminate undesired noise
caused by cable movement.
The cable can be secured
in one of two orientations,
depending on the location
of your camera’s “Audio In”
socket.
See diagram 1 for cameras
with mic socket on the left.
See diagram 2 for cameras
with mic socket on the right.
2. Slide the camera-shoe into place on the
camera mount. When the mic is in place,
secure it by gently tightening the ring
clockwise.
3. Connect the VideoMic’s audio lead to
the camera’s “Audio In” or “Mic” socket,
and secure the cable in place using the
in-built cable clips (see below).
mounting to camera
securing the cable
PAD switchbattery
1
1
2
2
3
The VideoMic comes with a three-position
PAD switch which is located inside the battery
compartment.
The PAD provides a selectable 10 or 20db
reduction of the input sensitivity, reducing
the output level when recording loud sound
sources, so that the optimal level can be
achieved in a wide range of situations.
To change the battery, gently push
and slide the battery cover off. Insert a
standard 9V battery with the positive
(+) end upwards.
The VideoMic uses a standard 9V
battery. With a good quality Alkaline
or Lithium battery, the VideoMic will
run for up to 100 continuous hours. We
recommend you remove the battery
if storing your VideoMic for extended
periods without use.
+
–
Push the cable in from the bottom.
028_952_1_Videomic_Quickstart.indd 2028_952_1_Videomic_Quickstart.indd 2 17/12/2012 8:46:21 AM17/12/2012 8:46:21 AM
  • Page 1 1
  • Page 2 2

Rode VideoMic User manual

VideoMic
Rode
Brand
Rode
Model
VideoMic
Category
Microphones
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents