Kenmore 41790814002 Owner's manual

Brand: Kenmore

Model: 41790814002

Category: Washing machines

Type: Owner's manual

LA UNDR Y CENTER

Owners GJide

LAVADORA Y SECADORA

SUPERPUESTAS

Table of Contents

Impor_ant Safety Instructions.............................................. 2-3

Washing Procedures ......................................................... 4-5

Stain Removal .................................................................... 6

Common Washing Problems ................................................. 7

Drying Procedures .............................................................. 8

Features ............................................................................ 9

Commom Drying Problems ................................................... 9

Care and Cleaning ........................................................ 10-11

Avoid Service Checklist ................................................. 11-13

Warranty and Service......................................................... 14

Espar_ol....................................................................... 15-28

Instrucciones Importantes de Seguridad ........................... 15-16

Metodos de Lavado ..................................................... 17-19

Limpieza de Manchas ................................................... 19-20

Problemas Comunes del Lavado ......................................... 21

Metodos de Secado .......................................................... 22

Caracteristicas .................................................................. 23

Problemas Comunes de Secado ........................................ 23

Cuidado y Limpieza ..................................................... 24-25

Lista de Control de Averias ............................................ 25-27

Back Cover ...................................................................... 28

Product Registration

Thank you for choosing this

dryer. Thisowner's guide will

explain proper operation and care.

Theself-addressedPRODUCT

REGISTRATIONCARDshould be

filled in completely, signed and

returned.

Registro del Producto

Le agradecernos que haya seleccio-

nado esta secadora. En este manual

del usuario encontrara las intrucciones

apropiadas para su funcionamiento y

cuidado.

Registre su Producto

La TARJETA DE REGISTRO DEL

PRODUCTO ya dirigida debe ser

Ilenada, firmada y enviada.

Read and Save These Instructions

Record Your Model and Serial Numbers

Recordbelowthe model addserialnumbersfound onthe laundrycenterserial

plate located on the insideof the dryer door. Keepthese numbers for future

reference,

Anote su Ndmero de Modelo y de Serie

Anote a continuaci6n elnOmerode modelo y de serieque seencuentran en

la placa de seriesituada en el interior de la puerta de la secadora. Conserve

estosnOmerospara referencia futura.

Model Number:

Ndmero de Modelo:

Serial Number:.

N_mero de Serie:

Purchase Date:

Fecha de compra:

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.frigidaire.com PN 131786800D (0504)

For your safety, the information in this manual must be followed to minimize the risk

of fire or explosion or to prevent property damage, personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building or area of all occupants.

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed bya qualified installer, service agency or the gas supplier.

Avoid

fire hazard or electrical

shock. Do not use an

adaptorplugor extension

cordorremovegrounding

prong from electrical

power cord. Failure to

follow this warning can

causeserious injury, fire

or death.

Grounding type

wall receptacle

GAS I..AUNDRYCENTER_

fDo not under _'_

any circumstances

cut, remove,

_ or bypass

the grounding prong

from this plug j

c_.. Powersupply

cordwith 3-prong

rounding plug

CCIIRECI"

Use this way ONLY

Important Safety Instructions

This Owner's Guide provides

general operating

instructions for your laundry

center, ft also contains

information about features

for several other models.

Your laundry center may not

have every feature included.

Use the laundry center only

as instructed in this Owner's

Guide.

Note: The instructions

appearing in this Owner's

Guide are not meant to cover

every possible condition and

situation that may occur.

Common sense and caution

must be practiced when

installing, operating and

maintaining any appliance.

Read all instructions before using this laundry center.

To reduce the risk of fire, electrical shock, or injury to persons when using this laundry center, comply with the basic warnings listed

below.

[] Failure to comply with these warnings could result in serious personal injuries.

Prevent Fire

Do not wash or dry items that have been previously cleaned in, soaked in, or spotted with gasoline, cleaning solvents, kerosene, waxes,

etc. Do not store these items on or near the dryer. These substances give off vapors that could ignite or explode.

Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that

could cause a load to catch fire.

Do not put oily or greasy rags or clothing on top of the laundry center. These substances give off vapors that could ignite the materials

Do not add gasoline, cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors

that could ignite or explode.

Under certain conditions, hydrogen gas may beproduced in ahot water system that has not been used for 2 weeks or more. HYDROGEN

GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washer, turn on all hot water faucets and let the

water flow from each for several minutes. This will release any accumulated hydrogen gas. Hydrogen gas is flammable; do not smoke or use an open

flame during this time.

[r_ To prevent fire, do not use heat to dry items containing plastic, foam rubber or similarly textured rubber-like materials, or items containing

feathers or down. Use Air Fluff (No Heat) only.

Clean the dryer lint screen before or after each load. The interior of the dryer, lint screen housing and exhaust duct should be cleaned

approximately every 18 months by qualified service personnel An excessiveamount of lint build-up in these areas could result in inefficient drying and

possible fire. See Care and Cleaning, pages 12-13.

Do not operate the dryer if the lint screen is blocked, damaged or missing. Fire hazard, overheating and damage to fabrics can occur.

If your dryer has a drying rack, always replace the lint screen when finished using the drying rack

Keep area around the exhaust opening and surrounding areas free from the accumulation of lint, dust and dirt.

Do not obstruct the flow of ventilating air. Do not stack or place laundry or throw rugs against the front or back of the laundry center

Do not spray any type of aerosol into, on or near laundry center at any time.

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

[] Failure to comply with these warnings could result in fire, explosion, serious bodily injury and/or damage to the rubber or plastic parts of the laundry

center.

2 Printed in U.S.A.

Important Safety Instructions Con't

Do not use or mix liquid

chlorine bleach with other household

chemicals such as toilet cleaners, rust

removers, acid or products containing

ammonia. These mixtures canproduce

dangerous fumes which can cause

serio us injury or death.

Protect Children

Do not allow children to play onor in the laundry center. Close supervision of children

isnecessarywhen the laundry center is used near children. As children grow, teach them the proper,

safe use of all appliances.

Destroy the carton, plastic bag and other packing materials after the laundry center

is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads or plastic

sheets can become airtight chambers.

Keep laundry products out of children's reach. To prevent personaI injury, observe

all warnings on product labels.

Before the laundry center is removed from service or discarded, remove the washer

lid and dryer door to prevent accidental entrapment.

[] Failure to comply with these warnings could result in serious personal injuries.

Prevent Injury

To prevent shock hazard and assure stability during operation, the laundry center

must be installed and electrically grounded by a qualified service person in accordance with local

codes. Installation instructions are packed in the laundry center for the installer's reference. Refer

to INSTALLATIONINSTRUCTIONSfor detailed grounding procedures. If the laundry center is moved

to a new location, have it checked and reinstalled by a quaIified service person.

To prevent personal injury or damage to the laundry center, the electrical power

cord of a gas laundry center must be plugged into a properly grounded system. Never ground lJ_e

laundry center to a gas pipe. Do not use an extension cord or an adaptor plug.

Follow package directions when using laundry products. Incorrect usage can

produce poisonous gas--resulting in serious Injury or death.

• Do not combine laundry products for use in 1 load unless specified on the label.

• Do not mix chlorine bleach with ammonia or acids such as vinegar.

To prevent serious personal injury and damage to the laundry center:

• All repairs and servicing must be performed by an authorized servicer unless specifically

recommended in this Owner's Guide. Use only authorized factory parts.

• Do not tamper with controls.

• Do not install or store the laundry center where it will be exposed to the weather.

ALWAYS disconnect the laundry center from the electrical supply before

attempting any service or cleaning. Failure to do so can result in electrical shock or injury.

_i_ Do not use any type spray cleanser when cleaning dryer interior. Hazardous fumes

or electrical shock could occur.

To prevent injury, do not reach into the washer while parts are moving. Before

loading, unloading or adding items, push in the cycle selector knob and allow the tub to coast to

a complete stop before reaching inside,

To prevent injury,do not reach into the dryer if the drum is moving. Wait until the

dryer has stopped completely before reaching into the drum.

[] A thermal limiter switch automatically turns off the dryer motor in the unlikely event of an

overheated situation (electric dryersonly). A servicetechnician must replace the thermallimiter switch

after correcting the fault.

[] The washer is equipped with an electrical overload protector. The motor will stop if it becomes

overheated. The washer will automatically restart after a cool down period of up to 30 minutes,

if the washer has not been manually turned off during this time.

[] Failure to comply with these warnings could result in serious personal injuries.

SAVE THESE INSTRUCTIONS

Washing Procedures

Sortlaundry into loadsthat canbe

washedtogether.

• Follow the guidelines below for preparing the wash load.

• Readthe Washer Operating Instructions, pages 17-18, for operating your

specific model.

• Always read and follow fabric care and laundry product labels.

To reducethe riskof fire, electricalshock, or injuryto persons,read

Important Safetylnstructions, pages2-4, before operating this washer.

1. Sort laundry into loads that can be washed together.

Sortitems byrecommended water temperatures, wash time, and agitatelspin

speeds.

• Separatewhite, light, andcolorfast itemsfrom darkand noncolorfast items.

• Separateitems which shed lint from items which attract lint. Permanent

press,synthetic, knit and corduroy itemswill pick up lint from towels, rugs

and chenille bedspreads.

• Separateheavily soiled items from lightly soiled items.

• Separatelacy,sheerand loosely knit itemsfrom sturdy items.

Emptypockels.

2. Prepare items for washing.

• Emptypockets.

• Brushoff lint and dirt. Shakeout rugsand beachtowels.

• Closezippers,fasten hooks,tiestringsandsashes,andremovenonwashable

trims and ornaments.

• Removepins, decorative buttons, belt buckles, and other objects which

could be damaged. This alsohelpsprotect other items in the wash load.

• Mend ripsand tears to prevent further damage during washing.

• Placedelicateitemssuchasbras,shoulder pads,hosiery,andbeltsin amesh

bag to prevent tangling during the wash cycle.

• Turn knit itemsinside out to preventpilling.

Place delicate items in a mesh bag.

Bleach Dispenser(some models)

3. Pretreat stains and heavy soil.

Seestain Removal, pages7-8, for details.

4. Add a measured amount of detergent to the wash tub

before adding the laundry load.

Follow detergent manufacturer's directions. Theamount required depends on

type of detergent, load sizeand soil level, and water hardness.

5. Ifdesired, addliquidbleachtoBleachDispenser(somemodels).

• Beforeadding the wash load,add liquid bleachto bleachdispenserlocated

in left front corner under the lid:

• 3/4 cup (180 ml) for small loads

• 1 cup (240 ml) for large loads

• 1-114cups (300 ml)for extra-large loads.

• Then add I cup (240 ml) water to flush the dispenser.

• Do not use powdered bleach in the bleach dispenser.

Formodels withouta bleach dispenser, dilute the recommended amount of

liquid chlorine bleach in 1 quart (.95 L) water. Add it to wash water after

a few minutes of agitation. Do notpour bleach directly on wash load.

Washing Procedures (continued)

Do not loaditemsabove

top row of holesin washtub.

Built-In Fabric Softener Dispenser

(somemodels)

Built-InFabricSoftenerDispenser

(some models)

RemovableFabricSoftener Dispenser

(somemodels)

Safety Lid Lock

Add laundry load to washer.

• Dry loadlevelshould not be higher than top row of bolesinwashtub.

Do not overload washer.

• Do not put items on top of agitator or wrap them around it. Loaditems

evenly.

• Combine large and smallitems in aload. Loadlarge itemsfirst. Largeitems

should not be more than half the total wash load.

• When washing asingle heavy item, add 1or 2 towels to balancethe load.

If desired, add liquid fabric softener to Fabric Softener

Dispenser (some models).

For models with a built-in dispenser (see picture to the left):

1. Add liquidsoftenertothe dispenser,following fabricsoftener labeldirections.

2. Add water to bring liquid levelto fill lineon dispensercap.

3. Removethe dispenserfrom the agitator after eachuse.Rinseboth cap and

cup with warm water. Replacedispenser in the agitator.

NOTE:Toseparatecapfrom cup,put thumb into dispenserandpushagainstside

of cup(seepicture to the left). After cleaning,pushcapand cupfirmly together.

Replacedispenserbylining upthe ribsandgroovesandsnapping it intoposition.

Fabric softener will be flushed from area under the built-in fabric softener

dispenserwhen LargeLoadWater Levelisselected.Ifabuild-up offabric softener

occurs, cleanwith hot water. DO NOT REMOVE SERVICECAP.

Formodels with a removable dispenser (seepicture below to the left):

1. Attach fabric softener dispenserto top of agitator bypressingdown gently.

2. Add softener to the dispenser,following fabric softener label directions.

3. Add water to bring liquid levelto top of the peg in the center of the cup.

4. Removethe dispenserfrom the agitator after eachuse. Rinseboth lid and

bowl thoroughly with warm water. Reassembleand place dispenser on

agitator or store it nearby.

Formodels withouta fabricsoftenerdispenser, follow fabric softener label

directions. Add diluted fabric softener to the final rinse. Do notpour fabric

softener directly on the wash load.

Set cycle selector knob and washer controls according to

type, size, and soil level of each load, and detergent used.

seeoperating Instructions for your specific model controls•

Start the washer.

Close the washer lid and pull out the cycle selector knob• The washer will not

agitate or spin with the lid open.

• To stop the washer, push in the cycle selector knob.

• To change a cycle, push in the cycle selector knob. Turn it clockwise to the

desired setting• Pull out the knob to restart the washer.

10. Remove items when the cycle is completed.

Foryour safety, the lid lockswhen the tub isspinning. It will remain locked for

about 1minute after the tub stopsspinning.

• Toopenthe lidduring aspin,pushin thecycleselectorknob andwait about

1 minute for the lid lock to release.Do not force open the locked lid.

Placewashed items in automatic dryer, line dry, or dryflat asdirected byfabric

carelabel. Excesswrinkling, color transfer or odorsmay develop in items left in

the washer after the cyclehas ended.

_To avoid serious personalinjury, do not operate washer ifsafety lid

lock ismissing or damaged.

Stain Removal

Do not combine stain removal products.

Follow fabric care label instructions.

Safe Stain Removal Procedures

To reduce the risk of fire or serious injury to persons or property, comply with the

basic warnings listed below:

Read and comply with all instructions on stain removal products.

Keep products in their original labeled containers and out of children's reach.

Thoroughly wash any utensil used.

Do not combine stain removal products, especially ammonia and chlorine bleach.

Dangerous fumes may result.

Never wash items which have been previously cleaned in, washed in, soaked in or spotted

with gasoline, dry cleaning solvents or other flammable or explosive substances because

they give off vapors that could ignite or explode.

Never use highly flammable solvents, such as gasoline, inside the home. Vapors can

explode on contact with flames or sparks.

For successful stain removal:

Remove stains promptly.

Determine the kind of stain, then follow recommended treatment in the stain rein

chart on the next page.

To pretreat stains, use a prewash product, liquid detergent, or a paste made from

granular detergent and water.

Use cold water on unknown stains because hot water can set stains.

Check care label instructions for treatments to avoid on specific fabrics.

Check for colorfastness by testing stain remover on an inside seam.

Rinse and wash items after stain removal.

STAIN TREATMENT

Adhesive tape, chewing gum, Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or

rubber cement nonflammable dry cleaning fluid.

Baby formula, dairy products, Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more. Wash.

egg

Beverages (coffee, tea, Pretreat stain. Wash using cold water and bleach safe for fabric.

soda,juice, alcoholic beverages)

Blood Rinsewith cold water. Rub with bar soap. Or, pretreat or soak with product containing enzymes. Wash using

bleach safe for fabric.

Candle wax, crayon Scrape off surface wax. Place stain face down between paper towels. Presswith warm iron until wax is

absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable

dry cleaning fluid Hand wash to remove solvent. Wash using bleach safe for fabric.

Chocolate Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.

Collar or cuff soil, cosmetics Pretreat with prewash stain remover or rub with bar soap.

Dye transfer on white fabric Use packaged color remover. Wash using bleach safe for fabric.

Grass Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.

Grease, oil, tar (butter, fats, Scrape residue from fabr c. Pretreat Wash us ng hottest water safe for fabric. For heavy stains and tar apply

salad dressing, cooking oils, nonflammable dry cleaning fluid to back of stain. Replacetowels under stain frequently. Rinse thoroughiy. Wash

car grease, motor oils) using hottest water safe for fabric.

Ink Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured

alcohol or nonflammable dry cleaning fluid

Mildew, scorch Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly

mildewed fabrics may be permanently damaged.

Mud Brush off dry mud. Retreat or soak with product containing enzymes.

Mustard, tomato Pretreat with prewash stain remover. Wash using bleach safe for fabric.

Nail polish May be impossible to remove. Placestain face down on paper towels. Apply nail polish remover to back of stain.

Repeat, replacing paper towels frequently Do not use on acetate fabrics.

Paint, varnish WATER BASED:Rinsefabric in cool water while stain is wet. Wash. Once paint is dry it cannot be removed. OIL

BASEDAND VARNISH: Use solvent recommended on can label. Rinse thoroughly beTore washing.

Perspiration Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach in hottest water safe for

fabric.

Rust, brown or yellow For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and

discoloration nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.

Shoe polish LIQUID: Pretreat with a paste of granular detergent and water. PASTE:Scrape residue from fabric. Pretreat

with prewash stain remover or nonflammable dry cleaning fluid. Rinse. Rub detergent into dampened area.

Wash using bleach safe for fabric.

Urine, vomit, mucus, feces Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.

Common Washing Problems

Manywashing problems involve poor soil and stain removal, residues,flint and scum, and fabricdamage. For satisfactory washing

results, follow these suggestions provided by The Soap and Detergent Association.

PROBLEM POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES

•Detergent or liquid fabric softener ,If caused by detergent, mix t cup (240 ,Add detergent before wash load. Then

Blue stains did not dissolve or disperse, ml) white vinegar with 1 quart (.95 L) start washer.

water in a plastic container. Soak item 1

hour. Rinse -Dilute fabric softener with water.

• If caused by fabric softener, rub stains

with bar soap. Wash.

Discoloration,

graying

Greasy, oily stains

•Not enough detergent.

•Wash water temperature too

low.

,Incorrect sorting.

•Not enough detergent

•Undiluted liquid fabric softener

poured directly on fabric.

• Rewash with correct amount of

detergent and hottest water safe for

fabric. Add bleach safe for fabric.

•Treat with prewash stain remover or

liquid detergent.

• Increase detergent and water

temperature Rewash.

• Rub fabric softener stains with bar soap.

,Sort items by soil level and color.

• Use correct amount of detergent, hottest

water and bleach safe for fabric

• Use correct amount of detergent and

hottest water safe for fabric.

"Do not pour liquid fabric softener

direct_ on fabric. See package directions

or Washing Procedures for proper

diluting.

Holes, tears, or

snags

,Incorrect use of chlorine bleach

•Unfastened zippers, hooks,

buckles.

•Rips, tears and broken threads.

•Overloading the washer.

•Degradation of fabric.

• May be irreversible if rips. tears and

seams cannot be mended.

•Never pour chlorine bleach directly on

fabric.

,Check condition of items before washing.

See Washing Procedures for preparing

and loading the wash load.

Lint

•Incorrect sorting.

•Tissues left in pocket.

•Overloading the washer.

•Not enough detergent.

• Undissolved detergent has left

residue.

• Static cling is attracting tint.

• Load washed too long

• Reduce load size. Rewash using correct

water temperature, water level, and

amount of detergent.

•Add nonprecipitating water conditioner

to wash water.

•Add liquid fabric softener to final rinse.

• Dry load in dryer

• Remove lint with lint brush or roller.

,See Washing Procedures for sorting and

preparing the wash load.

•Do not overload washer.

*Use correct amount of detergent, water

temperature and water level

Pilling

(Fibers break off,

ball up and cling to

fabric)

• Pilling is normal with synthetic and

permanent press fabrics. This is

due to abrasion from normal

wear.

• Use a lint brush or shaver to remove

pills.

•Use fabric softener in the washer to

lubricate fibers.

•When ironing, use spray starch or fabric

finish on collars and cuffs.

•Turn items inside out to reduce abrasion.

Residue or powder

on dark items;

Stiff, harsh fabrics.

• Undissolved detergent.

• Some nonphosphate granular

detergents can combine with

hard water minerals to form a

residue.

.Reduce load size.

•Add dissolved detergent to tub . Rewash

load.

• Mix 1 cup (240 m!) white vinegar to 1

gallon (3.8 L) warm water in plastic

container. Soak item. Rinse and rewash.

• Increase water temperature using hottest

water safe for fabric.

• Do not overload washer.

• Use liquid detergent or use

nonprecipitating water conditioner with

nonphosphate granular detergent.

Wrinkling

Yellow buildup of

body soil on

synthetic fabrics

Yellow or brown

rust stains

• Overloading the washer.

•Reduce load size.

•Rinse in cold water with liquid fabric

softener.

• Do not overload washer.

• Remove items from washer as soon as

cycle is completed.

• Use liquid fabric softener.

• Agitation time too short.

• Wash water temperature too

low.

• Not enough detergent.

•Soak in detergent booster or product

containing enzymes.

• Wash in hot water (120°F/4g°c) using full

permanent press cycle. Increase

detergent.

Add bleach safe for fabric

• Or, treat with color remover.

• Wash synthetics frequently using water at

least IOO°F(37°C) and correct water level.

• Iron or manganese in water

supply, water pipes, or water

heater.

• To restore discolored load of whites, use

rust remover safe for fabric.

Do not use chlorine bleach to remove

rust stains, It may intensify

discoloration.

• Use nonprecipitating water softener

• Before washing, run hot water for a few

minutes to clear lines.

• Drain water heater occasionally

• For an ongoing problem, install an iron

filter in your water supply system.

Dnj,ing Procedures

Followfabriccare label instructions.

Place small items in a mesh bag.

Filldryerdrum 1/3to 1/2 full.

• Follow the guidelines below for preparing the load for drying.

• ReadtheOryerOperatinglnstructions, pages19-20,foroperatingyourspecific

model.

• Always read and follow fabric care labels and laundry product labels.

_To reducethe riskof fire, electricalshock, or injury to persons,read

Important Safetylnstructions, pages2-4, before operating this dryer.

1. Prepare items for drying.

• Dry items of similar fabric, weight and construction in the same load.

• Separate dark items from light-colored items. Separate items that shed lint

from those that attract lint. If an item sheds lint, turn it inside out.

Besurebuckles,buttons andtrim areheatproof andwon't damagethedrum

finish. Closezippers,fastenhooksandVelcro®-Iike fasteners.Tiestringsand

sashesto prevent snagging and tangling.

If possible, turn pockets inside out for even drying.

Check for stains which may not have been removed in washing. Dryer heat

may permanently set some stains. Repeat stain removal process before

drying.

Placesmall items in a mesh bag to prevent tangling andfor easyremoval.

2. Check that lint screen is clean and in place.

3. Load the dryer.

• Theaverageloadwillfill thedrum 1/3to 1/2full. Itemsneedroom to tumble

freely for evendrying and lesswrinkling. Do not overload dryer.

• When drying large items, dry only 2or 3 at a time. Fillout the load with small

and medium sized items.

For delicate or very small loads, add 2 lint-free towels for better drying, less

wrinkling, and to prevent grease stains caused by fabric softener sheets.

Do not overd ry items. Overd rying can causewrinkling, shrinkage, harshness,

and a build-up of static electricity, which can produce more lint.

If desired, add a dryer fabric softener sheet.

4. Close the dryer door and set dryer controls (some models).

SeeDryer Operating Instructions cardfor your specific model controls.

5. Turn cycle selector clockwise to the desired setting.

6. Start the dryer.

• Turn Start control clockwiseto ON. Hold for 1-2 secondsand release.

• Toadd or removeitemswhen the dryerisrunning, open the door. Thedryer

will alwaysstop when the door isopened.

• Allow the drum to come to a complete stop before reaching inside.

7. When the cycle ends, remove items immediately and hang

or fold. If load isremoved before the cycleends, turn cycleselectorto OFF.

Features

Jsethedryingracktod_itemswhichshould

notbetumbled.

Cycle Signal Control (some models)

When the CycleSignalControl isON,asignalwill sound atthe end of eachcycleand

during the PressSaversetting (some models).The volume is adjustable on some

models.

Drum Light (some models)

A drum light will come onwhenever the door isopened to illuminate the dryerdrum

during loading and unloading. Closingthe door turns off the light.

Drying Rack (somemodels)

Usethe drying rackto dry itemswhich should not be tumble dried.

1. Open the dryer door and remove the lint screen.

2. Insert drying rack into the dryer drum. Place the front bar under the lip of the lint

screen opening.

3. Place items to be dried on top of rack. Weight should not exceed 10 Ibs. Leave

space between items, but do not let items hang over the sides or through the

grids. Do not tumble other items when using the drying rack.

4. Selectatimed dry setting bestsuited for itemsbeing dried. Useonlythe Air Fluff

(no heat)temperature setting for itemscontaining plastic,foam rubber, rubber-

like materials, feathers or down.

5. When items are dry, remove the rack and replace the lint screen. If lint screen

isnot in place, tumbling items could enter the exhaust system and cause damage

to the dryer.

CommonDrying

Problems

Many drying problems involve poor cleaning results, poor soil and stain removal, residuesof lint and scum, and fabric damage.

Forsatisfactorydrying results,follow these suggestions provided byThe Soapand Detergent Association.

PROBLEM POSSIBLECAUSES SOLUTIONS

Greasy, oily -Fabric softener sheet. -Rub fabric softener stains with bar

stains soap.

Rinse and rewash.

Lint

Pilling

(Fibers break off,

ball up and cling

to fabric.)

Shrinking

Wrinkling

PREVENllVE MEASURES

•Add a few bath towels to small loads for proper

tumbling.

•Some "silk-like" fabrics should be air dried.

• Use proper drying temperature.

• Place fabric softener sheet on top of load before

starting the dryer.

• Overloading.

• Overdrying causes static

electricity.

• Lint screen not clean when

cycle began.

• Lint is attached to "pills."

• Reduce load size and rewash using

liquid

fabric softener in the final rinse

• Or, add a fabric softener sheet and

tumble without heat.

• Use lint brush or roller to remove lint.

• Do not overload dryer.

• Use fabric softener in washer or dryer to reduce

static electricity.

• Remove items when they are slightly damp to

avoid overdrying.

•Check that lint screen is clean and in place.

• Pilling is normal with

synthetic and permanent

pressfabrics. This is due to

abrasion from normal

wear.

•Overdrying.

,Overloading.

• Leaving items in dryer after

cycle ends.

• Use a lint brush or shaver to remove

pills.

• Irreversible condition.

• Reduce load size and tumble at

medium

or low heat for 5-10 minutes.

• Remove items immediately. Hang or

fo_d.

•Use fabric softener to lubricate fibers.

•When ironing, use spray starch or fabric finish on

collars and cuffs.

•Turn items inside out to reduce abrasion

•Follow fabric care label directions.

•If shrinking is a concern, check load often.

• Remove items while slightly damp.

• Block knits into shape.

•Lay flat to complete drying.

• Do not overload dryer.

• Remove items as soon as cycle ends.

Care and Cleaning

Clean lint screen after every load.

Washlintscreenoccasionally.

Usecarewith laundnd

products.Theycandamagefinishon

filelaundrycenter.

Toreduce riskof fire or serious injuryto persons or property, cornply

with the basicwarnings listed in important Safety Instructions, pages2-4, and

those listed below.

• Beforecleaningthewasherordryerinterior, unplugtheelectricalpowercord

to avoid electrical shock hazards.

• Do not use any type spray cleanserwhen cleaning dryer interior. Hazardous

fumes or electrical shock could occur.

Inside the Washer

• Removeitemsfrom thewasher assoonasthe cycleends. Excesswrinkling, color

transfer, and odors may develop in items left in the washer•

• Dry the washer top, the areaaround the lid opening, and the undersideof the

lid. These areasshould always be dry before the lid isclosed,

• Beforecleaningthewasherinterior, unplugtheelectricalpewereordtoavoid

electrical shock hazards.

When extremely soiled items have been washed, a dirty residue may remain on

the tub. Remove this by wiping the tub with a nonabrasive household cleanser.

Rinsethoroughly with water.

Theagitator or tub maybecome stainedfrom fabric dye.Cleantheseparts with

a nonabrasivehousehold cleanser.This preventsdyetransfer to future loads•

Inside the Dryer

• Clean the dryer lint screenafter every load. Lint build-up in the screen restricts

air flow, which causeslonger drying times. Thescreenislocated atthe bottom

of the door opening. Removebypulling straight up.Removethe lint and replace

the screen.

Occasionally a waxy build-up may form on the lint screen from using dryer-added

fabric softener sheets. To remove this build-up, wash the lint screen in warm,

soapy water. Dry thoroughly and replace. Do not operate the dryer without the

lint screen in place.

Ifthedryerdrum becomesstainedfrom noncolorfastfabrics,cleanthedrum with

a damp cloth and a mild liquid household cleanser. Removecleanser residue

before drying the next load.

• Every 18 months an authorized servicer should clean the dryer cabinet interior

and exhaust duct. These areas can collect lint and dust over time. An excessive

amount of lint build-up could result in inefficient drying and possible fire hazard.

Outside

• When laundering is completed, wipe cabinet with a damp cloth. Turn water

faucets off to prevent pressurebuild-up inthe hoses.

• Clean the cabinet with mild soap and water• Never use harsh, gritty or

abrasive cleansers. Ifthe cabinet becomes stained, clean with diluted chlorine

bleach [1/2 cup (120 ml) in 1quart (.95 L)water]. Rinse several times with clear

water.

Remove glue residue from tape or labels with a mixture of warm water and mild

detergent. Or, touch residue with the sticky side of the tape or label•

Before moving the laundrycentero placeastripof cardboardorthin fiberboard

under the front leveling legsto prevent floor damage.

FoilowWinterizing

Instructions for cold

weather care.

Winterizing Instructions

Ifthe laundrycenter isstored inan areawhere freezingcanoccuror movedin freezing

temperatures, followthesewinterizing instructionsto prevent damagetothe la_Jndry

center:

1. Turn offwatersupplyfaucets.

2. Disconnect hosesfrom water supply and drain water from hoses.

3. Plug electricalcord into a properly grounded electrical outlet.

4. Add 1 gallon nontoxic recreational vehicle (RV)antifreeze to empty wash tub.

Close lid.

5. Setcycleselector knob at aspin setting. Pullout knob and let washer spinfor 1

minute to drain out all water. Not all of the RVantifreeze will beexpelled.

6. Pushin knob, unplug electrical power cord, dry tub interior, and closelid.

7. Storewasher in an upright position.

8. To remove antifreeze from washer after storage, run empty washer through a

complete cycleusing detergent. Do not add wash load.

Avoid ServiceChecklist

Before calling for service, review this list. It may save both time and expense. The list includes common concerns that are not the

result of defective workmanship or materials in this laundry center.

OCCURRENCE

POSSIBLECAUSE SOLUTION

WASHER- NOISE

"Clunking" or gear sounds. A certain amount of "clunking" or gear

sounds are normal in a heavy-duty

washer.

Rattling and clanking noise. Foreign objects such as coins or safety

pins may be in tub or pump.

This is normal.

Stop washer and check tub. If noise continues after

washer is restarted, objects may be in pump. Call your

authorized servicer.

Belt buckles and metal fasteners are To prevent unnecessary noise and damage to tub,

hitting wash tub. fasten fasteners and turn items inside out.

Squealing sound or hot Washer is overloaded.

rubber odor.

Do not overload washer. Stop washer and reduce load.

Thumping sound.

Vibrating noise.

Heavy wash loads may produce a

thumping sound.

Laundry center is not resting on a solid,

firm floor.

This is usually normal. If sound continues, washer is

probably out of balance. Stop washer and redistribute

wash load.

Move laundry center so it rests firmly on solid floor.

Additional floor bracing may be needed. Adjust leveling

legs. See INSTALLATION INSTRUCTIONSfor details.

Shipping bolt and block have not been

removed durinq installation.

See INSTALLATION INSTRUCTIONS for removing

shipping bolt and block.

Wash load unevenly distributed in tub. Stop washer and rearrange wash load.

WASH ER- OPERATING

Washer does not start. Electrical power cord may not be plugged Make sure plug fits tightly in wall outlet.

in or connection may be loose.

Housefuseblown,circuitbreakertripped, Reset circuit breaker or replace fuse. Do not increase

or a power outage has occurred, fuse capacity. If problem is a circuit overload, have it

corrected by a qualified electrician. If problem is a

power outage, call local electric company.

Water supply faucets are not turned on. Turn on water supply faucets.

OCCURRENCE POSSIBLE CAUSE SOLUTION

WASHER -OPERATING

(€onlinued)

Washer does not start Cycle selector is not in correct position. Move indicator clockwise slightly. Pull out knob.

(continued).

Motor is overheated. Washer motor will stop if it becomes overheated. It will

automatically restart after a cool down period of up to

30 minutes (if washer has not been manually turned

off).

Washer won't spin, Lid is not completely closed. Close lid completely, Safety lid lock must not be broken.

Residue left in tub. Heavily soiled items. Wipe tub with a nonabrasive household cleanser, then

rinse. Shake or brush excess dirt and sand from items

before washing.

WASHER- WATER

Wash load too wet after Washer is overloaded. Do not overload washer. See Washing Procedures.

spin.

Load is out of balance. Rearrange load to allow proper spinning.

Drain hose is kinked. Straighten drain hose.

Water does not enter Water supply is not adequate in area. Check another faucet in the house. Wait until water

washer or it enters slowly, supply and pressure increase.

Water supply faucets are not completely open. Fully open hot and cold faucets.

Water is being used elsewhere in the house.Water pressuremust be at beast30 psi (260 kPa). Avoid

running water elsewhere while washer is filling.

Water inlet hoses are kinked. Straighten hoses.

Water level does not cover improper water level selection (for Select higher water levelAoad size.

load. models with water level/load size control).

Washer is overloaded. Do not overload washer. When control is set at highest

fill level, dry load level should not be higher than top row

of circular holes in wash tub.

Warm or hot water is not Hot water heater is set too low or is a Measure hot water temperature at nearby faucet with

hot enough, distance from laundry center, candy or meat thermometer. Water temperature should

be at least 130°F (70°C). Adjust water heater as

necessary.

Hot water is being used elsewhere in Avoid using hot water elsewhere before or during

the house, washer use. There may not be enough hot water

available for proper cleaning. If problem persists, your

hot water system may be unable to suppor_ more than

1 use at a time.

Water in washer does not Drain hose is kinked or clogged. Clean and straighten the drain hose.

drain or drains slowly.

Water leaks. Fill hose connection at faucet or washer. Check and tighten hose connections. Install rubber

sealing washers provided.

House drain pipes are clogged. Unclog drain pipes, Contact plumber if necessary.

Oversudsing. Use less detergent.

Incorrect wash and rinse Hot and cold water hoses are connected Connect hot water hose to hot water faucet and cold

temperatures, to wrong supply faucets, water hose to cold water faucet.

Water is entering washer Drain hose standpipe is incorrect height. Standpipe must be a minimum of 33" (83.82 cm) high

but tub does not fill. to prevent siphoning. See INSTALLATION

INSTRUCTIONS.

OCCURRENCE POSSIBLECAUSE SOLUTION

DRYER

Dryer does not start. Electrical power cord is not securely Make sure the plug fits tightly in wall outlet.

plugged in or plug may be loose.

House fuse blown or circuit breaker Reset circuit breaker or replace fuse.

tripped.

Make sure electrical line is not overloaded and the dryer

is on a separate circuit.

Thermal limiter tripped. Call authorized service person for replacement.

Dryer runs but won't There are 2 house fuses in the dryer Replace fuse.

heat. circuit. If 1 of the 2 fuses is blown, the

drum may turn but the heater will not

operate.

Gassupplyvalveisnotopen(gasmodels). Check to make sure supply valve is open. See

INSTALLATION INSTRUCTIONS for procedure.

Dryer does not have enough air supply to See INSTALLATION INSTRUCTIONS.

support the burner flame (gas models).

LPgas supply tank is empty or there has Refill or replace tank.

been a utility interruption of natural gas

(gas models). Dryer should heat when utility service is restored.

Drying cycle takes too Lint screen is clogged with lint. Make sure all lint has been removed from the dryer lint

long, outsideofthedryer screen before starting each cycle.

feels too hot or smells

hot. Exhaust duct requirements have not been Exhaust duct must be at least 4 inches in diameter and

met. made of rigid or flexible metal.

When in place, the duct must have no more than two

90° bends and must not exceed length listed in

INSTALLATION INSTRUCTIONS.

Electric dryer is connected to a 208 volt Drying time will be 20% longer than drying on a 240 volt

circuit, circuit.

Drying procedures have not been See Drying Procedures, page 10.

followed.

Outside exhaust hood or exhaust duct Clean out any obstruction.

may be clogged or restricted.

High humidity. Use a dehumidifier near the dryer.

Excessive wrinkling.

Dryer is overloaded. Do not overload. See Drying Procedures, page 10.

Items left in dryer too long. Remove items as soon as cycle ends.

Insufficient sorting of items. See Drying Procedures, page 10.

Drying temperature too high. Follow fabric care label instructions.

Full One Year Warranty on Mechanical and

Electrical Parts

For one year from the date of purchase, if this

Laundry Center isinstalled and operated according

to the instructions in the Owner's Guide, Operating

Instructions, and Installation Instructions. Searswill

repair or replace any of its mechanical or electrical

parts if they are defective in material or

workmanship.

NOTE: Exhausting your Laundry Center with plastic

product may void this warranty. The Installation

Instructions manual describes the complete

exhaust requirements for this Laundry Center.

Limited Five Year Warranty on Gear Case Parts

After one year and until five years from the date of

purchase, Sears will replace any gear case paris that

are defective in material or workmanship. You must

pay the labor cost to have them installed.

Limited Ten Year Warranty on Plastic Tub

After one year and until ten years from the date of

purchase. Sears will furnish a replacement plastic

tub for any plastic tub that is defective in material

or workmanship. You must pay the labor cost to

have the plastic tub installed.

Warranty Restriction

If the Laundry Center is operated for any purpose

other than Private Family Use, all warranty

coverage is effective for only 90 days.

Warranty Service

Warranty service is available by contacting your

nearest Sears Service Center in the United States.

This warranty applies only while this Laundry

Center is in use in the United States.

This warranty gives you specific legal rights, and

you may also have other rights which vary from

state to state.

Sears, Roebuck and Co., Dept. 817WA,

Hoffman Estates, IL 60179

Your safety and the safety of others is very important.

We have provided many important safety messages in the Owner's Guide,

Operating Instructions, Installation Instructions and on your appliance. Always

read and obey aft safety messages.

This is the safety alert symboL This symbol alerts you to hazards that

can kill or hurt you or others. AII safety messages will be preceded by

the safety alert symbol and the word "DANGER" or "WARNING".

These words mean:

You will be killed or seriously injured if you don't

follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will identify the hazard, tell you ho w to reduce the chance

of injury, and tell you what can happen if the instructions are not followed.

! ''=''j'_''_''_'=" Para su sequridad sicla las instrucciones contenidas en este manual a fin de reducir a

un m nimo los riesgos de i6cend o o _xplos 6n o para ev tar dahos mater a es, esiones personales o la

muerte.

No almacene ni utilice gasolina u otros vapores y liquidos inflamables en la proximidad de _ste o de

cualquier otto artefacto el_ctrico.

QUE DEBE HACER SI PERCIBE OLOR A GAS:

• No trate de encender ningOn artefacto el_ctrico.

• No toque ningOn interruptor el_ctrico; no use ningOn tel_fono en su edificio.

• Haga salir a todos los ocupantes de la habitaci6n, del edificio y del lugar.

• Llame a su proveedor de gas desde el tel_fono de un vecino. Siga las instrucciones del proveedor

de gas.

• Si no Iogra comunicarse con su proveedor de gas, Ilame al departamento de bomberos.

La instalaci6n y el servicio de mantenimiento debe realizarlos un instalador calificado, la agencia de

servicios o el proveedor de gas.

Instrucciones Importantes de Seguridad

Lea todas las Instrucdones antes de usar esta lavadora y secadora superpuestas.

Parareducir el riesgo de incendio, choque el_ctrico o lesiones personales cuando se esta usando lalavadora y secadora superpuestas,

siga las siguientes precauaones b_sicas.

] El incumplimiento de estas advertencias puede resultar en lesiones personales serias.

Evite los Incendios

N_ _ave_ sequearticu_s que hansid_ anteri_rmente _impiad_s_rem_iad_s _ manchad_s c_n gas_Iina_s_iventes de iimpieza_ker_s_n_

cera, etc. No guarde estos art_culos en o cerca de la secadora. Estas substancias emiten vapores que pueden inflamarse o explotar.

_No coloque en su secadora ninguna prenda que haya sido expuesta a los aceites de cocina. Elaceite de cocina contenido en estas

prendas puede treat una reaccion quimica que puede causar alas prendas de encenderse.

No ponga patios o ropas manchadas con aceite o grasa sabre la lavadora y secadora superpuestas. Estas substancias desprenden

caLory vapores que pueden hater encender los materiales.

No agregue gasolina, solventes de limpieza u otras substanciasexplosivas o inflamables al agua de lavado. Estassubstancias emiten

vapores que pueden inflamarse o explotar.

Bajo ciertas condiciones se puede produdr hidrogeno en un sistema de agua caliente que no ha sido usado pot 2 semanas o m_s.

EL HIDROGENO ES EXPLOSIVO Si el sistema del agua caliente no ha sido usado por un periodo de esa Iongitud, antes de usar la lavadora, abra todas

las Ilavesdel agua caliente y deje correr el agua durante ratios minutos. Estoeliminar_ el hidr6geno acumulado. Debido a que el gas es inflamable, no fume

ni use una llama abierta en tal momento.

Paraevitar incendios no use calor para secar ar_iculos que contienen pl_stico, goma de espuma o materiales similares a la goma,

ni almohadas o ropas que contengan plumas de ave. Use salamente "AIR FLUFF"{Aire Sin Calor).

Limpie el filtro de pelusa de la secadora antes y despu_s de cada usa. El interior de la secadora, la caja del filtro de pelusay el duc¢o

de escape deben ser limpiados aproximadamente cada 18 mesespor personal de servicio calificado. Cualquier acumulaci6n excesiva de pelusas en estas

_reas puede resultar en secado deficiente y posible incendio. Vet Cuidado y Limpieza, paginas 12-13

No haga funcionar la secadora si el filtro de pelusa est_ bloqueado, dahado o no est_ colocado Puede ocurrir sobrecalentamiento,

daflo a las telas y un peligro de incendio. Si su secadora tiene una parrilla de secado, siempre vuelva a colocar el filtro de pelusa cuando termine de usar

la parrilIa.

Mantenga el area alrededor de la abertura del escape y las _reas vecinas sin acumulacibn de pelusa, polvo y suciedad.

No obstruya el fluio del aire deventilaci6n • Noapile ropa de lavaro alfombras enfrente o detras de lavadoray secadorasuperpuestas.

Este Manual del Usuario le proporciona instrucciones de funcionamiento

generales para su lavadora y secadora superpuestas. Adem_s contiene

informacion sobre lascaracteristicas para varios otros modelos Su lavadora

y secadora superpuestas pueden no tener todas las caracteristicas descritas

en este manual.

Use la lavadora y secadora superpuestas solamente como se indica en este

Manual y en las tarjetas de Instruccio-nes de Fundonamiento que se

incluyen con la lavadora y secadora superpuestas.

Nora: /as instrucciones incluidas en

este Manual del Usuario, no pueden

cubrir todas las situaciones o

condiciones posibles que puedan

presentarse. Por Io tanto, se debe

usar sentido com0n y tener cuidado

cuando se instala, se hace funcionar

y se repara cualquier artefacto.

15 Impreso en EE. UU.

Evitelos

riesgosdeincendiosochoque

electrico.Nouseuncordonde

extensi6nounadaptadorparael

tomacorriente,nisaqueninguna

espigadelenchufedelcordon

el_ctrico.Elincumplimientodeesta

advertenciapuedecausaruna_esi6n

grave,unincendioolamuer_e.

Baj° n_ngunaclrcuns 1

Tomato en e

_ancBa torte, saque o

pueSto _ tlerra •

ponga en denvao6n

laespiga de puesta a

_s_e enchufe

pu_to a tierra

COn enchu_e de

CORRECTO

Use de esta manera SOLAMENTE

Instrucciones Importantes de

Seguridad (continuaci6n)

No use

mezcle blanqueador de cloro

tiquidocon otrosproductosquimicos

dom_s-ticos tales como productos

para limpiar el ba6o, antioxidantes,

productos _cidos o que contengan

amoniaco, Estas mezdas pueden

producir vapores peligrosos que

pueden causar lesiones graveso la

muerte.

CONSERVE ESTAS INSTRUCCIONES

Nunca rocie ning_n tipo de aerosol dentro, encima o cerca de la lavadora y secadora superpuestas.

No use suavizantes de ropa ni productos para eliminar la est_tica a menos que sea recomendado por el fabricante del suavizante

de ropa o del producto.

] El incumplimiento de estasadverLenciaspuede resultar en incendio explosi6n lesiones corporales graves y/o da6o alas piezas de goma o pl_stico

de a lavadora y secadora superpuestas.

Proteja a los Ni_os

No permita que los ni_osjueguen con la lavadora y secadora superpuestas. Esnecesario supervisar atentamente cuando la lavadora

y secadora est_n siendo usadas cerca de los ni_os. A medida que los ni6os crecen, ens66eles a usar en forma segura y correcta todos los arLefactos.

Destruya _acaja de carton, lasbolsas de plastico y los flejesde metal despu_s de que se ha desempacado Lalavadora y secadora

superpuestas. Los ni_os pueden para jugar. Lascajas de car_6n cubiertas con alfombras, colchas o pl_stico pueden transformarse en c_maras herm_ticas

Mantenga los productos de lavanderia fuera del a_cance de los niflos Para evitar lesi6n personal observe todas las adver_encias

de las etiquetas de los productos.

Antes de que la avadora ysecadora superpuestas seanenviadas a servicioo descartadas, saque latapa de la lavadoray de lasecadora

para evitar que alguien quede atrapado accidentalmente en el interior.

] El incumpiimiento de estas advertencias puede resultar en lesiones personales graves•

Evite las Lesiones

La lavadora y secadora superpuestas deben ser instaladas y puestas a tierra de acuerdo con los codigos tocales pot un t_cnico de

serviciocalificado para evitar el riesgo de choque el_rico y asegurar estabilidad durante el funcionamiento. Lasinstrucciones de instalacion han sido colocadas

en la Lavadoray secadora superpuestas para referencia del instalador, Consulte las INSTRUCCIONESDE INSTALACION para los detalles del procedimiento

de puesta a tierra. Si lalavadora y secadora superpuestas son transportadas a un nuevo lugar, h_galasrevisar y reinstalar por un tecnico de serviciocalificado.

_Para evitar lesi6n personal o da_o a la lavadora y secadora superpuestas, el cord6n electrico debe ser enchufado en un tomacorriente

de 3 tomas debidamente puesto a tierra y polarizado. Nunca se debe sacar la tercera clavija de puesta a tierra. Nunca ponga a tierra la lavadora

y secadora superpuestas en una tuberia de gas. No use un cord6n de extensi6n o un adaptador.

_Siga lasinstrucciones de losenvasescuando use productos de lavanderia. Eluso incorrecto puede producir gasvenenoso - resultando

en una lesion grave o la muerte.

No combine productos de lavanderia para usar en una carga a menos que asi se especifique en la etiqueta.

No mezcle el blanqueador de cioro con amon_acoo _cidos tales como el vinagre.

_Para evitar lesi6n personal y da6os a la lavadora y secadora superpuestas:

Todas las reparaciones deben ser efectuada$ pot un t_cnico autorizado a menos que haya sido especificamente recomendadoen este Manual

del Usuario. Use solamente piezas autorizadas por la f_brica.

No modifique los controles.

No instale o aLmacenela lavadora y secaclora superpuestas donde estar_ expuesta alas inclemenciasdel tiempo.

SIEMPRE desconecte la lavadora y secadora superpuestas de la alimentacion el_ctrica antes de intentar efectuar reparaci6n

o limpieza. De _ocontrario puede producirse un choque el_ctrico o lesibn.

No use ningOn tipo de _impiador en aerosol cuando limpie el interior de la secadora Pueden producirse vapores peligrosos o choque

el_ctrico.

_Para evitar lesiones, nunca trate de alcanzar algo en el interior de la lavadora cuando las piezas est_n en movimiento. Antes de

poner, sacar o agregar ar_iculos,oprima el boton selector de cido y deje que la tina se detenga completamente antes de aicanzar el interior de la lavadora.

_Para evitar lesiones, no introduzca la mano en la secadora si el tambor se esta moviendo Espere hasta que la secadora se haya

completamente antes de hacerlo.

]Un ruptor t_rmico apaga autom_ticamente el motor de la secadora en e_improbable caso de producirse sobrecalentamiento (secadoras el_ctricas

solamente). Un t_cnico electricista debe reemplazar el ruptor t_rmico despu_s de corregir la falla.

]La lavadora est_ equipada con un protector de sobrecarga el_ctrica. El motor se detendr_ si se sobrecalienta. La lavadora se pondr_ autom_ticamente

en marcha nuevamente despu_s de un periodo de enfriamiento de hasta 30 minutos, si es que no ha sido apagada manualmente en ese mornento.

]El incumplimiento de estas adver_encias puede resultar en lesiones personales graves.

M todos de Lavado

3LAN(_IADO

PERM,

RO "/_'

TOALLAS

Separe la ropa en cargas que puedan

serlavadasjuntas.

Vacielosbolsillos,

Coloque losarticulos delicados en una

bolsa de malla.

f_ f/f_

• Siga las instrucciones indicadas a continuaciOn para separar la ropa.

• Lea la tarjeta de Instrucciones de Fundonamiento de la Lavadora

correspondiente a su modelo especffico.

• $iempre lea y siga las indicaciones de las etiquetas sobre cuidado de las

telas y de los productos para el lavado.

Para reducir el riesgo de incendio, choque el_ctrico o lesiones

personales, antes de usar esta lavadora, lea la secci6n Instrucciones Importante$

deSeguridad, p_ginas 2-4.

Separe la ropa en cargas que puedan ser lavadas juntas.

Separelosarticulos de acuerdo alas temperaturas del agua recomendada, a la

duracion del lavadoy alas velocidades de agitaciOny exprimido.

• Separe los articulos blancos, livianos y que no destiflen de los articulos

obscurosy que desti_en.

• Separelosarticulosque producen pelusadeaquellosque atraenpelusa.Los

art[culos de planchado permanente, sint_ticos, tejidos y de pana atraer_n

la pelusa de lastoallas, alfombras y cubrecamas de felpillas.

• Separelosa_iculos que est_ndemasiadomanchadosdeaquellosque estan

menossucios.

• Separelosartfculos de encaje, transparentes ytejidos livianosde aquellos

articulos m_sresistentes.

Prepare la ropa para el lavado.

• Vacielos bolsillos.

• Escobillela pelusay suciedad.Sacudalasalfombras y lastoallas de playa.

• Cierre los zipers, abroche los ganchos, amarre los cordones, lazos o

cinturones y saquelos adornosy ornamentos que no seanlavables.

• Saque los alfileres, botones decorativos, hebillas de cinturones y otros

objetos que puedan da_arse.Estotambien ayudaaproteger otros a_[culos

del lavado.

• Remiende losrasgones para evitar que seda_en m_s durante el lavado.

• Coloque losartfculos delicados talescomo sostenes,hombreras, mediasy

cinturones en una bolsade malla para evitar que se enreden durante el

lavado.

• Coloque al rev_slosarticulos tejidos para evitar que produzcan pelusa.

3. Prelavado de manchas y suciedad m_s impregnada.

Ver Limpieza de Manchas, p_ginas7-8, para losdetalles.

Agregue una cantidad medida de detergente a la tina de la

lavadora antes de colocar la ropa.

Siga las indicaciones del fabricante del detergente. La cantidad requerida

depende del tipo de detergente, del tama_o de la carga y nivelde suciedady

de la dureza del agua.

Si se desea, agregue blanqueador liquido al Dep6sito del

Blanqueador (algunos modelos).

• Antes de colocar la ropa, agregue blanqueador l[quido al depOsito del

blanqueador situado en la esquinadelantera derecha bajo latapa:

• 314de taza (180 ml) para cargas pequer_as

• I taza (240 ml) para cargas grandes

• 1-114tazas(300 ml) para cargasmuy grandes.

• Luego agregue I taza(240 ml) de agua para lavarel depOsito.

• No useblanqueador en polvo en el deposito del blanqueador.

Paralosmodelos que no tienen undep6sito para elblanqueador, disuelva

lacantidad recomendada de blanqueador de cloro liquido en I cuarto de galOn

(0,95 L)de agua.Agr_guelo al agua del lavadodespu_sde unospocosminutos

de agitaciOn.No vacie el blanqueador directamente sobre la ropa.

Dep&sito del Blanqueador

(algunos modelos)

Procedimientos para el

Lavado (cont.)

No recargue articulos mas arriba

de la primera fila de agujeros

de la tina lavado.

Dispensador para Suavizadores de Telas

incorporado (algunos modelos)

Dispensador para Suavizadores de Telas

incorporado (algunos modelos)

/z:i

Dispensador para Suavizadores de Telas

amovible (algunos modelos)

6. Agregue a la lavadora la carga de lavado.

• El nivel de la carga secano debe pasarla linea de agujeros superiorde la

tina de la lavadora.No recargue la lavadora.

No coloque articulos encima del agitador ni los enrosque alrededor de el.

Coloque los articulos en forma pareja.

Combine ardculos grandes y peque_os en una carga. Coloque primero los

articulos grandes. Los ardculos grandes no deben set mas de la mitad del

total de la carga a lavarse.

Cuando se laveun solo articulo pesado, aOadaI o 2 toallas para

balancear la carga.

7. Si se desea, afiada un suavizante liquido para telas en el

Dispensador de Suavizantes de Telas (algunos modelos).

Para modelos con dispensador incorporado (ver la figura a la izquierda):

1. Agregue el suavizante I[quido en el dispensador, siguiendo las instrucciones

de la etiquete del suavizante para telas.

2. Agregue agua para traer el nivel del liquido a la linea de Ileno en la tapa

del dispensador.

3. Remueva el dispensador del agitador despuOs de cada uso. Eniuague la taza

y su tapa con agua tibia. Coloque el dispensador en el agitador.

Nota: Para separar el casquete de la taza, ponga el pulgar en el depOsito y

apdete contra el 1ado de la taza (ilustraciOn a la izquierda). DespuOs de la

limpieza, reconecte el casquete y la taza. Vuelva a colocar el dep0sito por alinear

los hilos y las ranuras.

El sauvizante se saldra desde el ,irea debajo del depOsito fijo para suavizante de

telas cuando se selecciona Large Load (cargas grandes). Si un sedimento de

suavizante se produce, limpie el area adentro de] agitador con agua caliente.

NO QUITE EL CASQUETE DE SERVlCIO.

Para modelos con dispensador amovible (ver la figura de abajo a la

izquierda):

I. Encaje el dispensador de suavizante para telas en la parte superior del

agitador presionando gentilmente.

2. Agregue el suavizante en el dispensador, siguiendo las instrucciones de la

etiquete del suavizante para telas.

3. Agregue agua para traer el nivel del liquido a la altura superior de la clavija

en el centro de la taza.

4. Remueva el dispensador del agitador despuOs de cada uso. Enjuague la taza

y su tapa con agua tibia. Arme nuevamente y coloque el dispensador en el

agitador o almacOnelo en un lugar proximo.

Para modelos sin dispensador de suavizante para telas, siga las instrucciones

de la etiqueta del suavizante. AOada suavizante diluido en el enjuague final. No

a_ada suavizante en forma directa en la carga para lavaro

Coloque la perilla selectora de ciclo y los controles de la

la vadora de acuerdo al tipo, tamaOo, y nivel de suciedad de

cada carga, y del detergente usado.

Vea latarjeta de InstruccionesDe Funcionamiento para loscontroles de su

tipo de modelo.

Procedimientos para el

Lavado (cont.)

_ Cierredeseguridad

"%) -___

"'i

Ponga en marcha la lavadora.

Cierrelatapa ytire haciaafuera el botOnselectorde ciclo.Lalavadoranoagitar_

ni escurrido con la tapa abierta.

Paradetener la lavadora, oprima el botOnselector de ciclo.

Paracambiar el ciclo, oprima el botOn selectorde ciclo, girelo a la derecha

haciala posiciOndeseada.Tirehaciaafuera el botOnparavolver aponer en

marcha la lavadora.

10. Saque la ropa cuando el ciclo haya terminado.

Para su seguridad, la tapa se bloquea cuando la tina est_ exprimiendo.

Permanecer_ bloqueada durante I minuto despu_s de que la tina deja de

exprimir.

• Para abrir la tapa durante el ciclo de exprimido, oprima el boton selector de

ciclo y espere aproximadamente I minuto para que la tapa se desbloquee.

No trate de abrir la tapa cuando est_ todavia bloqueada.

Coloque la ropa lavada en la secadora autom,ttica, en una cuerda de secar o d_jela

secar en forma horizontal como se recomiende en la etiqueta sobre el cuidado de

las telas. Se pueden formar arrugas excesivas, transferencia de color u olor si deja

la ropa en la lavadora despu_s que el ciclo haya terminado.

_Para evitar dahospersonalesserios,no usela lavadorasila cierre

de seguridad de la tapa le falta o si esta dahada.

Limpieza de Manchas

No mezcle losproductos para quitar

lasmanchas.

Siga las instrucciones de la etiqueta sobre

el cuidado de las telas.

Mdtodos para Quitar las Manchas

Parareducirelriesgode incendioo lesionpersonalgraveo dahos

materiales, observe lasadvertencias que seindican a continuaciOn:

• Leaysiga todas lasinstrucciones indicadas en losquitamanchas.

• Mantenga los productos en susenvasesoriginales y fuera del alcance de los

nihos.

Lavebien todos losutensilios usados.

No mezclelosproductos para quitar manchas, especialmenteel amonfacoyel

cloro. Sepueden producir vaporespeligrosos.

Nunca lave articulos que anteriormente hayan sido limpiados, lavados, sumergidos

o manchados con gasolina, solventes de limpieza en seco u otras substancias

inflamables o explosivas pues ellos emiten vapores que pueden encenderse o

explotar.

Nunca use solventes inflamables, tales como gasolina, dentro del hogar. Los

vapores pueden explotar al entrar en contacto con llamas o chispas.

Para limpiar bien las manchas:

• Quite las manchas r_pidamente.

• Determine la clasede la mancha, luego siga el tratamiento recomendado en

la tabla para limpieza de manchas en la p_gina siguiente.

• Para pretratar las manchas, use un producto de prelavado, detergente liquido

o una pasta hecha de detergente en polvo y agua.

• Use agua fria en las manchas conocidas pues el agua caliente puede fijar las

manchas.

Verifique las instrucciones en la etiqueta de cuidado de la tela para los

tratamientos que deben set evitados en ciertas telas especificas.

Verifique si las telas se desti_en probando el quitamanchas en una costura

interior.

• Enjuague y lave losarticulos despu_sde quitar lasmanchas.

Limpieza de Manchas

MANCHA TRATAMIENTO

Cinta adhesiva, goma de Aplique hielo. Raspe todo el exceso. Coloque la mancha hacia abajo sobre toallas de papel. Impregne la mancha con

mascar, cemento para goma quitamanchas de prelavado o _iquido para lirnpieza en seco no inflamable.

F6rmula para beb_s, Use un producto que contenga enzlmas para pretratar o remojar las manchas Remoje durante 30 minutos o m_s. Lave.

productos I_cteos. huevo

Bebidas (caf_, t_. bebidas Primero trate la mancha. Luego lave con agua fria y blanqueador apropiado para telas.

gaseosas, jugos, bebidas

alcoh61icas)

Sangre Enjuague con agua fr[a. Frote con una barra de jabon O, trate o remoje primero con un producto que contenga enzimas.

Lave con un blanqueador apropiado para la tel&

Cera de velas, I_pices de cera Raspetoda la cera superficial. Coloque la mancha hacia abaJoentre dos toallas de papel. Planche con una plancha tibia

hasta que la cerasea absorbida Cambie las toallas de papel con frecuencia. Trate la mancha restante con quitamanchas

de prelavado o liquido para limpieza en seco no inflamable.Lavea mano para sacar el solvente. Lavecon un blanqueador

apropiado para la tela.

Chocolate Trate o remoje pnmero en agua tibia con un producto que contenga enzimas. Lave con un btanqueador apropiado para

la tel&

Suciedad de cuellos y pu_os, Trate primero la mancha con quitamanchas de prelavado o frote con una barra de jabbn

cosm_ticos

Telasblancaste_idasconotras Use un quitamanchas de color envasado. Lave y agregue blanqueador apropiado para la tela.

Hierba Trate o remoje primero en agua tibia con un producto que contenga enzimas. Lave con un blanqueador apropiado para

la tela.

Grasa, aceite, alquitr_n Raspe todo residuo de la tel& Trate primero la mancha. Lave usando el agua m_s caliente que sea apropiada para la

(mantequitla, grasas, con- te_a.Paramanchasdensasya_quitran_ap_ique_iquid_paraiimpiezaensec_n_inf_amab_ep_rdetr_sde_amancha._ambie

dimento de ensaladas,aceites las toallas de papel bajo la mancha con ffecuencia. Enjuague bien. Lave usando el agua m_s caliente que sea apropiada

de cocinar, grasa de para la tel&

autom6viles, aceite de

motores)

Tinta Algunas manchas de tinta no podr_n ser quitadas. El lavado puede fijar atgunas manchas de tint& Use quitamanchas

de prelavado, alcohol desnaturalizado o liquido para limpieza en seco no inflamable.

Mi_di_, quemaduras Lavecon blanqueador de cloro si no es peligroso para la tela. O remoje en blanqueador oxigenado y agua caliente antes

de lavar. Las telas manchadas de mildiu pueden quedar perrnanentemente da_adas

Lodo Cepille el _odo seco. Trate o remoje primero con un producto que contenga enz_mas.

Mostaza, tomates Trate primero la mancha con quitamanchas de prelavado. Aplique removedor de manchas. Lave con un blanqueador

apropiado para la tela.

Esmalte para u6as Puede que sea imposible de quitar. Coloque la mancha hacia abajo sobre toallas de papel. Aplique quitaesmalte de uflas

por detr_s de la mancha. Repita cambiando las toallas de papel con frecuencia No use en telas de acetato.

Pintura, barniz PINTURAAL AGUA: para lasmanchas frescas, enjuague la tela con agua fria. Lave Cuando la pintura se secaes imposible

de quitar. PINTURAAL ACEITEY BARNIZ: Use el solvente recomendado en el envase de la pintura Enjuague muy bien

antes de lavar.

Transpiraci6n Use quitamanchas de prelavado y _rote con una barra de jabbn. Enjuague. Lavecon blanqueador sin cloro. Lave usando

el agua rnas caliente que sea apropiada para la tela.

Oxido, decoloracion caf_ o Paralas manchas de 6xido aplique un quitamanchas que sea apropiado para latela Paradecoloraci6n detodo el lavado

amarilla use detergente fosfatado y blanqueador sin cloro. No use blanqueador de clon_ pues puede aumentar la

decoloraci6n.

BetQn de zapatos LIOUIDO:Trate la mancha con una pasta de detergente en polvo y agua. PASTA:Raspetodo el residuo de la tela. Aplique

quitamanchas o liquido para limpieza en seco no inflamable. Enjuague. Frote con detergente los lugares mojados. Lave

con un blanqueador apropiado para la tela.

Orina, vomito, mucus, heces Trate o remoje primero con un producto que contenga enzimas Lave con un blanqueador apropiado para la tela

Page is loading ...

Kenmore 41790814002 Owner's manual

Brand: Kenmore

Model: 41790814002

Category: Washing machines

Type: Owner's manual

Download PDF

report

in other languages

español: Kenmore 41790814002 El manual del propietario

Kenmore 41790814002 Owner's manual

Kenmore 41790814002 Owner's manual

in other languages

Related papers

Other documents