EGO TS Installation Instructions Manual

Brand: EGO

Model: TS

Category: Mobile phones

Type: Installation Instructions Manual

Installation instructions

Toyota Auris

128 8220 1.02

English

(Built from 2007)

EGO TS

Table of contents

1 Introduction / Preface ................................................................... 3

2 Safety Instructions ...................................................................... 4

3 Conformity statement ................................................................. 5

4 Scope of Delivery / Package content ........................................... 6

5 Installation instructions .............................................................. 7

5.1 Preparation ............................................................................................ 7

5.2 Installation locations ............................................................................. 7

5.2.1 Checking cable lengths ................................................................................................ 7

5.2.2 Selection of the installation location for the electronics box ...................................... 7

5.2.3 Selection of the point of installation for the microphone ............................................ 8

5.3 Mounting Components ........................................................................... 9

5.3.1 Mounting the electronics box ....................................................................................... 9

5.3.2 Mounting the microphone ............................................................................................ 9

5.4 Connection Concept ............................................................................... 10

5.5 Installation of the components .............................................................. 10

5.6 Functional Test ...................................................................................... 14

5.7 Symbols ................................................................................................. 14

5.7.1 Key functions ................................................................................................................ 14

5.8 Getting started ....................................................................................... 15

5.8.1 On / Off function ........................................................................................................... 15

5.8.2 Coupling ........................................................................................................................ 15

5.8.3 Automatic coupling ....................................................................................................... 15

5.8.4 LED status .................................................................................................................... 15

6 Troubleshooting .......................................................................... 16

7 Spares and accessories .............................................................. 17

8 Technical speciﬁcations .............................................................. 18

9 Certiﬁcation ................................................................................ 18

10 Hotline ......................................................................................... 19

Introduction / Preface1

Congratulations on your new EGO!

EGO TS is the intelligent entry-level solution for telephone use in your car: simple to operate,

elegant and compact – with Bluetooth and audio enjoyment too.

The installation of your EGO TS in your car requires specialist knowledge and skills. We recom-

mend that the installation be carried out in a qualiﬁed professional workshop.

Before installation in your car, please make sure that your mobile phone is fully compatible with

EGO TS. If you are uncertain, please consult your dealer or a professional workshop. Our service

team will also be happy to help you with any information you may require. You can ﬁnd further

information on compatibility between EGO TS and various mobile phones on our website.

2 | 3

EGO TS

Safety Instructions2

Incorrect installation1. – Incorrect installation may lead to damage to the units and/or your

car! Special knowledge and skills are required for installing the system. We strongly re-

commend that the system be installed by a qualiﬁed professional workshop.

2. Risk of injury – Unsuitable installation locations may become a source of injury in an acci-

dent situation, or may inhibit the correct functioning of essential safety equipment. Please

read the notes in the „Installation“ chapter carefully!

3. Risk of injury/material damage – the removal of cladding within the vehicle with sharp or

pointed tools may lead to injuries or material damage.

4. Road safety risk – Distracted attention can lead to dangerous situations in trafﬁc. Even

when using hands-free phone sy stems, your complete attention must be concentrated on

your driving and other road users. It is always advisable to do without phone calls in difﬁcu-

lt trafﬁc situations!

5. Damage to airbags – The wrong choice of location for installation may cause damage to

or inhibit the correct function of your airbags. Always install the components in a position

where they will not hinder the correct operation of airbags!

6. Insulation damage – Damaged insulation can lead to equipment and wiring damage. The

cables and leads may not be under tension when installed. Install the cables and leads in

such a way as to avoid pinching or abrasion.

7. Polarity and shorting damage – Cables connected with reversed polarity, or in such a way

as to produce a short circuit, can lead to serious damage to your equipment. Before com-

mencing installation, make sure that the car battery is disconnected.

8. Damage to essential vehicle components – Essential vehicle components or wiring can be

damaged when drilling mounting holes or screwing in self-threading screws. Please make

sure there is always sufﬁcient space behind the screw holes and drilled holes!

9. Interference with on-board electronics – Despite the extreme protection against interfe-

rence, incorrect installation can lead to interference with the vehicle electronic systems.

Please read the vehicle manufacturer’s notes to this effect!

Appropriate use10. – This equipment is intended solely for use with mobile telephones in mo-

tor vehicles.

11. Damage caused by inappropriate replacement parts – Inappropriate spare or replacement

parts may lead to malfunctions. Please use only the approved parts listed in the section

„Spares and accessories“!

Road safety risk12. – For your own safety, never initiate the coupling procedure while your

vehicle is in motion!

Conformity statement3

This equipment employs Bluetooth® wireless technology. In some countries, the use of this

equipment may be restricted or forbidden. Please make sure you are familiar with such restric-

tions and do not use your equipment if you are unsure whether its use is permitted in particular

countries you may be visiting.

Bluetooth® is a registered brand name of Bluetooth SIG, Inc.

The ﬁrm of Funkwerk Dabendorf GmbH

Märkische Straße

D-15806 Dabendorf

herewith declares that the hands-free system „EGO TS“

in accordance with the essential requirements and other relevant provisions

of the Directive 1999/5/EC.

0681

4 | 5

EGO TS

Scope of Delivery / Package content4

À Electronics box

Á Control unit

Â Microphone

Ã Extension cable

Ä Quick Guide

ÃÄ

Installation instructions5

Improper Installation

Improper installation may cause damages to the unit or to the vehicle! The installation

of the hands-free car kit requires special knowledge and special abilities. Short circuits

or cables connected in reverse polarity can cause severe damage to the unit. Ensure the

vehicle’s battery is disconnected before you start the installation procedure. We therefo-

re recommend to have the installation done by a professional.

Preparation5.1

Test audio system -

Place protective covers on seats etc. -

Turn Off ignition -

Installation locations5.2

RISK OF INJURY!

Unsuitable installation locations may become a source of injury in an accident situation,

or may inhibit the correct functioning of essential safety equipment!

Checking cable lengths5.2.1

Before you ﬁx the components securely, check that the installation locations have been selected

in such a way that the length of the cables is sufﬁcient to connect the individual components.

Selection of the installation location for the electronics box5.2.2

The Bluetooth® antenna for the connec-

tion to the mobile phone is installed in

the electronics box. The antenna trans-

mits directionally towards the front. For

this reason, during installation, ensure

that the antenna faces into the passen-

ger cell (see Fig.). Vertical mounting is

ideal. Metallic screening between the

front panel and the passenger cell, such

as metal or metallised plastic panels,

are unsuitable and may interfere with

the Bluetooth® connection. Locations

behind the dashboard or in a metal-lined glove compartment are also unsuitable.

A covering in plastic, fabric or wood presents no problems whatsoever

6 | 7

EGO TS

Suitable locations for the

electronics box:

- Passenger side, next to the centre

column under the panelling, model-

speciﬁc installation console (dealer)

- Our suggested installation locations

are shown in the illustration on the

right

Further unsuitable locations are:

Leg and knee height, potential head

impact zone, airbag inﬂation space,

engine compartment

Selection of the point of installation for the microphone5.2.3

Suitable for the microphone:

- where voice can reach the microphone

unhindered (distance between the spea-

ker and the microphone should be ap-

prox. 35 cm), on the A-column (between

windscreen and side window), next to

the driver‘s sun visor, on the dashboard

The illustration shows one of the po-

tential microphone mounting locations.

Alternatively, the microphone may be

attached to the sun visor with the clip

provided.

Unsuitable for the microphone:

-Close to the speakers (less than

80 cm), under the dashboard, in the air

stream from open windows or ventilator

outlets

Mounting Components5.3

DAMAGE TO ESSENTIAL VEHICLE COMPONENTS!

Essential vehicle components or wiring can be damaged when drilling mounting holes

or screwing in self-threading screws. Please make sure there is always sufﬁcient space

behind the screw holes and drilled holes!

Mounting the electronics box5.3.1

Deﬁne the mounting points

Making sure that there is at least

70 mm space for the plug and

socket connectors. Mark the posi-

tions for the ﬁxing screws.

Mounting the electronics box

For mounting the electronics box,

use four self-threading screws

and appropriate washers. We

recommend size “ST 2,9x25 DIN

7981”self-threading screws. These

are ideal for the ﬁxing of the electronics box. Pre-drill the holes with a 2 mm drill.

Mounting the microphone5.3.2

Deﬁne the mounting location

The microphone holder has a self-adhesive strip on the back. The mounting location should

have the same form and area as the self-adhesive strip on the microphone holder. The location

selected must allow the microphone cable to reach the electronics box! Locate the microphone

with its head in the direction of speech.

Cleaning and degreasing the mounting location

The mounting location must be clean and free from grease and dirt/dust. Clean the proposed

area with a cleansing product such as methylated spirits. Only use cleansing products that

do not damage plastics or varnished wood ﬁnishes and are themselves free of oils or grease.

Unsuitable cleansers are, for example,: lighter ﬂuid, acetone, turpentine, trichloroethylene and

similar products.

Attaching the microphone holder

Peel off the protective backing from the self-adhesive strip. Hold the microphone holder at a

distance of several millimetres above the desired mounting location. Recheck the positioning.

Repositioning after mounting is no longer possible. Place the microphone holder on the moun-

ting location and ﬁx by applying short and light pressure.

Attaching the microphone

Attach the microphone by sliding it into the holder and orientate the microphone head in the

direction of speech.

130 mm

45 mm70 mm

8 | 9

EGO TS

Connection Concept5.4

Installation of the components5.5

In order not to cause any damage while dismantling the interior panelling it is advisable

to use the so-called dismantling wedges! These leave no marks on the plastic parts!

Remove the speedometer covering.1.

Loosen the mounting screws and remove the speedometer unit.2.

Microphone Mounted

charger

(optional)

Control unit Connection

cable

Carefully dismantle the panelling on the left and right next to the radio.3.

Remove the ventilation unit and loosen the connector.4.

Loosen the 2 screws each on the left and right next to the radio5.

10 | 11

EGO TS

Pull the radio out of the slot carefully and remove the connectors of the radio.6.

Connect the adapter cables speciﬁc for the car.7.

Lay the connection line to the electronic box. Please pay attention to our explanatory notes 8.

on the point of installation of the electronic box in Chapter 5.2.2.

Choose a free installation slot for the EGO TS control unit. Carefully remove the covering and 9.

replace it by the control unit.

* Control panel element on the left next to the steering wheel.

Lay the microphone at a convenient spot, pay attention to our explanatory notes in 10.

Chapter 5.2.3.

Connect the control unit, the microphone and the system plugs to the electronic box.11.

NOTE: To prevent rattling sounds that may possibly occur we recommend that the cables be

fastened with cable straps and to position the electronic box tightly in the car.

12 | 13

EGO TS

Functional Test5.6

An operational test is only possible after coupling the system with a Bluetooth®- compatible

device. The procedure is explained in the sections „5.8. Getting started“.

Symbols5.7

The control console of the EGO TS has a total of 4 keys. The illustration on the right shows an

overview of the key locations. The functions of the individual keys are explained in the following

section.

Key functions5.7.1

→ The -key (green) is for accepting calls. It also controls the redial function,

private mode and connect manually.

→ The -key (red) is used for rejecting incoming calls and ending completed calls

(hang-up). It also controls the starts the phone‘s voice dialling function.

→ The -key increases the volume in phone.

→ The -key decreases the volume in phone.

Getting started5.8

Take enough time to familiarise yourself with the use of the system in combination with your

phone. First of all, make a few calls to determine the ideal volume and the best voice pick-up di-

rection before using the system in trafﬁc. The best way of optimising conditions of use is to park

your car in a quiet place especially for this purpose. It is also helpful if another phone user can

take some time to assist you when making test calls.

On / Off function5.8.1

Turning the ignition key simultaneously activates the hands-free system. Immediately after the

system is activated, the two LEDs blink 4 times. This indicates that the system is in standby

mode and ready to make a connection. In order to use the system for phone calls, a Bluetooth®

compatible phone must be coupled to the EGO TS system. How this is done is explained in detail

in the following sections. When the ignition is turned off, the hands-free system also shuts

down. If the ignition is turned off during a call, phone ability is maintained and the system is shut

down only after the call has been completed.

Coupling5.8.2

As long as no device is connected, the system is visible for all Bluetooth - ® devices.

The device to be used (mobile phone, PDA, etc.) must be logged in to the system. -

The Bluetooth® search and coupling are carried out by the device.

The name of the system is EGO TS.

The PIN has a default setting of 0000. -

Bei erfolgreicher Verbindung/Kopplung leuchten beide LED‘s dauerhaft. -

It can be 8 Bluetooth - ® phones be connected.

Automatic coupling5.8.3

If a phone is already connected with the system, the EGO TS tries to couple to this phone. When

a connection has been successfully made, the two LEDs are permanently on. The connection is

always made to the most recently coupled phone. If this phone is out of range, the system will

search for other phones registered in the system. When the search is successful, the connection

to this phone is completed automatically. If the search process was unsuccessful, the system

reverts to the coupling mode. This enables manual connection from the phone.

LED status5.8.4

Green blinks in short intervals → no device connected -

Both permanently on → device is connected -

Red on and green blinks periodically → active call -

14 | 15

EGO TS

Troubleshooting6

Problem Cause Correction

EGO TS doesn‘t

switch on

Power supply disabled If necessary, replace fuse and check

all leads and connections

Ignition not on Switch ignition on

Ignitions circuit disabled Check cable and 1 A fuse

Your call-partner can-

not hear you Microphone not plugged in

Connect microphone to electronics

box, defective cables require replace-

ment

Your call partner com-

plains about interfe-

rence

Microphone in air stream Mount microphone elsewhere or

reduce ventilation

Phone too close to EGO TS

components or car radio

Increase the distance between your

phone and

the EGO TS or radio

Your call partner hears

feedback

Distance between micro-

phone and speakers too

small

Increase distance or decrease volu-

Volume too high Decrease volume

Your phone cannot ﬁnd

EGO TS during coupling

EGO TS already connected

to another device Disconnect existing connection

Sound is unclear, dis-

torted

Poor Bluetooth® connec-

tion

Reduce the distance between your

phone and the EGO TS or remove any

(metallic) obstructions

No connection to

coupled phone when

ignition switched on

Phone is out of range. Make sure your phone is within the

range of the EGO TS.

Phone Bluetooth® inter-

face is deactivated.

Switch phone Bluetooth® function to

”ON“ (Option ”Automatic“ is not sufﬁ-

cient)

Phone requires conﬁrmati-

on of connection set-up.

Conﬁrm connection on your phone.

Deactivate security function (see

your phone manual)

One of the two devices no

longer has a valid connec-

tion code.

Repeat the coupling procedure.

Spares and accessories7

Spares

À Electronics box

Á Control unit

Â Microphone

Ã Extension cable

Accessories

Speciﬁc vehicle connection cable

ÂÃ

Variant Vehicle Equipment Connecting cable

Corolla E12 Standard MY2001>2004 Toyota

DENGS-00982-07

FWD 1284-01000

Land Cruiser J12 Standard

Hilux KUN 15/25 Option Wide2DIN (TNS310)

Avensis T25 Standard

Toyota

DENGS-00983-07

FWD 1284-02000

Full Map Navigation

Yaris XP9 Standard

Corolla Verso R10 Standard MY2004>

Full Map Navigation

Corolla E12 Standard

Full Map Navigation

Prius

RAV4 A3 Standard

Full Map Navigation

Hilux KUN 15/25 Standard SOL (MP3)

Auris Standard

Full Map Navigation

HIACE

Avensis T27 Standard

Verso Standard

CLand Cruiser J12 Full Map Navigation

Toyota

DENGS-00984-07

FWD 1284-03000

EIQ Standard

Toyota

DENGS-01410-07

FWD 1284-05000

16 | 17

EGO TS

Technical specifications8

External dimensions: Electronics box (L x B x H) 130 mm x 45 mm x 23 mm

External dimensions: Control unit (L x B x H) TS 1 33,7 mm x 22,9 mm x 26,6 mm

TS 2 42,2 mm x 24,2 mm x 20,8 mm

TS 3 39,3 mm x 20,8 mm x 24,2 mm

Cable length: Control unit 230 mm

Operating voltage 11 V to 15 V

Quiescent current (ignition off) max. 0,1 mA

Fuse: Permanent positive 2 A

Fuse: Ignition 1 A

Temperature range -10 °C bis +55 °C

Supported Bluetooth® Proﬁles: Handsfree

Certification9

0681

Fully compliant with the EU R&TTE Directive 1999/5/EC

Model certiﬁcation according to EU Directive 72/245/EWG (2006/28/EC) “Electromagnetic com-

patibility in motor vehicles”

Bluetooth® is a registered brand name of Bluetooth SIG, Inc.

Hotline10

Any questions or suggestions? Would you like some more detailed information? Do you need an

adviser or service in your area? Just give us a call!

Our Hotline Team is there to help you at the following times:

Monday–Thursday from 7.00 a.m. to 5.00 p.m.

Friday from 7.00 a.m. to 4.00 p.m.

Before you call us with your problem, please check ﬁrst with the following steps:

→ Check whether you can solve your problem with the „Troubleshooting“ checklist in chapter.

→ Try to explain your problem as precisely as possible.

You can contact our Hotline Team at the following numbers:

From Germany: Phone: 0800 - 0 393 393

From outside Germany: Phone: +49 (0) 3377 - 316 233

+49 (0) 3377 - 316 234

Fax: +49 (0) 3377 - 316 244

18 | 19

EGO TS

Funkwerk Dabendorf GmbH

Märkische Straße

D-15806 Dabendorf

Germany

Phone +49 (0) 3377 316 - 0

Fax +49 (0) 3377 316 - 300

Email info@fwd-online.de

service@fwd-online.de

Internet www.fwd-online.de A Funkwerk AG company.

Funkwerk Dabendorf reserves the right to modiﬁcations in the course of technological progress and deviations from the delivery

dorf GmbH!

EGO TS Installation Instructions Manual

Brand: EGO

Model: TS

Category: Mobile phones

Type: Installation Instructions Manual

Download PDF

report

EGO TS Installation Instructions Manual

EGO TS Installation Instructions Manual

Related papers

Other documents