ATEN VM0202H User manual

ATEN VanCryst™

VM0202H / VM0202HB

4K HDMI Matrix Switch / 2 x 2 True

4K HDMI Matrix Switch with Audio

De-Embedder

User Manual

VM0202H / VM0202HB User Manual

ii

Compliance Statements

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE

STATEMENT

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

The device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

FCC Caution

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment.

Warning

Operation of this equipment in a residential environment could cause radio

interference.

Achtung

Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen

verursachen.

KCC Statement

VM0202H / VM0202HB User Manual

iii

HDMI Trademark Statement

The terms HDMI, HDMI High-Definition Multimedia Interface, and the

HDMI Logo are trademarks or registered trademarks of HDMI Licensing

Administrator, Inc.

RoHS

This product is RoHS compliant.

VM0202H / VM0202HB User Manual

iv

About this Manual

This User Manual is provided to help you get the most from your VM0202H /

VM0202HB system. It covers all aspects of installation, configuration and

operation. An overview of the information found in the manual is provided

below.

Chapter 1, Introduction, introduces you to the VM0202H / VM0202HB

system. Its purpose, features and benefits are presented, and its front and back

panel components are described.

Chapter 2, Hardware Setup, describes how to set up your VM0202H /

VM0202HB installation and all necessary steps are provided.

Chapter 3, Operation, explains the fundamental concepts involved in

operating the VM0202H / VM0202HB via the front panel pushbuttons, and

remote control.

Chapter 4, RS-232 Operation, provides a complete list of the serial control

protocol commands used when utilizing the RS-232 Serial Port so that an extra

source device can be utilized in the installation.

Chapter 5, The Firmware Upgrade Utility, explains how to download the

VM0202H / VM0202HB’s firmware and upgrade the device using the utility.

An Appendix, provides specifications and other technical information

regarding the VM0202H / VM0202HB.

Conventions

This manual uses the following conventions:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear

together in the same bracket with a plus sign between them:

[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential steps.

>

Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

>

Run means to

open the Start menu, and then select Run.

Indicates critical information.

VM0202H / VM0202HB User Manual

v

Package Contents

VM0202H

 1 VM0202H 4K HDMI Matrix Switch

 1 IR remote control

 1 IR receiver

 1 power adapter

 1 mounting kit

 1 user instructions

VM0202HB

 1 VM0202HB 2 x 2 True 4K HDMI Matrix Switch with Audio De-

Embedder

 1 IR remote control

 1 IR receiver

 1 power adapter

 1 3-pole terminal block

 1 mounting kit

 1 user instructions

Note: 1. Make sure that all the components are present and in good order.

If anything is missing or was damaged in shipping, contact your

dealer.

2. Read this manual thoroughly and follow the installation and

operation procedures carefully to prevent any damage to the unit,

and/or any of the devices connected to it.

VM0202H / VM0202HB User Manual

vi

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized

Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

International http://www.aten.com

North America http://www.aten-usa.com

International http://eservice.aten.com

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1-949-428-1111

VM0202H / VM0202HB User Manual

vii

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

VM0202H / VM0202HB User Manual

viii

Contents

Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

1. Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Source Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Display Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

VM0202H Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

VM0202H Rear View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

VM0202HB Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

VM0202HB Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

IR Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2. Hardware Setup

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

VM0202H Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

VM0202HB Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Installing the RS-232 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3. Operation

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Front Panel Pushbuttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Video Output Pushbuttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Audio Output Pushbutton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Audio Channel Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

IR Remote Control Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Switching the Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Turning the Outputs on / off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Turning All Outputs on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

VM0202H / VM0202HB User Manual

ix

4. RS-232 Operation

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Connecting to the Matrix Switch via RS-232. . . . . . . . . . . . . . . . . . . . . . .21

Command Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Switch Port Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Audio Switch Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Audio Mute Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Auto Switch Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Read Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Echo Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

CEC Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Panel Button Control Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

EDID Mode Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Reset Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5. The Firmware Upgrade Utility

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . . 35

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

VM0202H / VM0202HB User Manual

x

This Page Intentionally Left Blank

1

Chapter 1

Introduction

Overview

The VM0202H / VM0202HB is a 2 x 2 True 4K HDMI Matrix Switch

featuring audio de-embedding (VM0202HB only). The VM0202H /

VM0202HB offers an easy and affordable way to route True 4K high-

definition HDMI video and audio. Supporting video resolutions up to 4096 x

2160@60Hz (4:4:4), HDR 10, HDR 10+, and HLG (VM0202HB only), audio

de-embedder (VM0202HB only), and data rates up to 18 Gbps (VM0202HB

only), the VM0202H / VM0202HB delivers robust signal routing and swift

digital video/audio switching that is perfect for most AV applications.

The VM0202H / VM0202HB matrix switch delivers superior video resolutions

up to 4096 x 2160@60Hz (4:4:4) (VM0202HB only), and also provides high-

performance routing of 2 HDMI video sources such as high-definition Blu-ray

players, home theater PCs, camcorders, DVD players, satellite boxes and

stand-alone streaming media players to any 2 HDMI displays. In addition, the

built-in audio de-embedder (VM0202HB only) allows HDMI audio extraction

for independent analog audio output with ease. For efficient control and

management, VM0202H / VM0202HB’s remote control and front-panel

pushbuttons provide a convenient way to cycle through HDMI video and audio

sources with clear LED indication of the selected source.

VM0202H / VM0202HB User Manual

2

Features

VM0202H

 Connects 2 HDMI sources to any of 2 HDMI displays

 Supports 4K resolutions of UHD (3840 x 2160) and DCI (4096 x 2160)

with refresh rates of 30 Hz (4:4:4) and 60 Hz (4:2:0)

 EDID Expert™ – selects optimum EDID settings for smooth power-up,

high-quality display, and use of the best video resolution across different

screens

 Multiple Control Methods – system management via front-panel

pushbuttons, IR and RS-232 serial control

 Supports Dolby True HD and DTS HD Master audio

 Signaling rates up to 3.4 Gbits for flawless 4K output

 HDMI (3D, Deep Color, 4K) and HDCP 1.4 compatible

 Consumer Electronics Control (CEC) allows interconnected HDMI

devices to communicate and respond to a single remote control

 Supports ATEN LockPro™ HDMI cable lock for securing HDMI cables

 ESD protection for HDMI ports

 Firmware upgradeable

 Rack Mountable 1U design

VM0202HB

 Connects 2 HDMI sources to any of 2 HDMI displays

 Max. Data Rate 18.0 Gbps (6.0 Gbps Per Lane)

 Supports True 4K resolutions up to 4096 x 2160 @ 60Hz (4:4:4) and HDR

include HDR 10, HDR 10+, and HLG

 Audio de-embedder – HDMI audio can be extracted to stereo or Line-out

audio

 Multiple Control Methods—system management via front-panel

pushbuttons, IR remote, and RS- 232 serial control

 Long-distance transmission up to 5 meters (with premium high-speed

HDMI cable)

 HDMI (3D, 4k, Deep Color); HDCP 2.2 Compatible

Chapter 1. Introduction

3

 Consumer Electronics Control (CEC) allows interconnected HDMI

devices to communicate and respond to one remote control

 EDID Expert™ — Selects optimum EDID settings for smooth power- up,

high-quality display and use of the best video resolution across different

screens

 Supports ATEN’s Lock Pro™ HDMI cable lock for secure HDMI cable

connections

 All metal casing

 Firmware upgradable

 Rack mountable (1U design)

Requirements

The following equipment is required for a complete VM0202H installation:

Source Device

 HDMI Type-A output connector(s)

Note: A DVI / HDMI adapter is required when connecting a DVI source

device.

Display Device

 Display devices or receivers with an HDMI Type-A input connector

Cables

 1 HDMI cable for each source device you will be connecting

 1 HDMI cable for each display device you will be connecting

 1 RS-232 serial cable

Note: 1. No cables are included in this package. We strongly recommend that

you purchase high-quality cables of appropriate length since this will

affect the quality of the audio and video display. Contact your dealer

to purchase the correct cable sets.

2. If you wish to utilize the VM0202H / VM0202HB’s high-end serial

controller function, you will also need to purchase an appropriate RS-

232 cable. See VM0202HB Installation, page 13.

VM0202H / VM0202HB User Manual

4

Components

VM0202H Front View

No. Component Description

1 video output

pushbuttons

Press an output port pushbutton to select an input

port.

Note: The OUTPUT (1-2) front panel pushbuttons

have built-in Green LEDs that light to indicate they

have been selected.

2 input select LEDs Indicates the input port of the corresponding output

port (output 1 or 2).

3 power pushbutton This pushbutton is to power on and off the VM0202H.

2

3

1

Chapter 1. Introduction

5

VM0202H Rear View

No. Component Description

1 cable tie slot Receives a cable tie to hold the power cable in place.

2 grounding terminal The grounding wire attaches here. Grounds the

VM0202H to prevent damages from power surge or

static electricity.

3 power jack The power adapter cable from an AC source plugs in

here. Receives a power adapter to supply power to the

VM0202H.

4 HDMI output ports The cables from your HDMI display devices plug into

these ports.

5 HDMI input ports The cables from your HDMI source devices plug into

these ports.

6 external IR receiver

port

Connect the IR receiver unit included with your product

via this 3.5 mm mini stereo jack.

7 Micro USB Type-B

port

Use this port to upgrade the firmware. See The

Firmware Upgrade Utility, page 35.

8 RS-232 serial port Connect a computer or high-end system controller via

this serial port.

52 3 4 6 7 8

1

VM0202H / VM0202HB User Manual

6

VM0202HB Front View

No. Component Description

1 video output

pushbuttons

Press an output port pushbutton to select an input

port.

Note: The OUTPUT (1-2) front panel pushbuttons

have built-in Green LEDs that light to indicate they

have been selected.

2 video input LEDs Indicates the input port of the corresponding output

port (output 1 or 2).

3 audio output

pushbutton

Press the audio output pushbutton to select an audio

output source.

Note: The OUTPUT (1-2) front panel pushbuttons

have built-in Green LEDs that light to indicate they

have been selected.

4 audio input LEDs Indicates the audio input port of the corresponding

input port (input 1 or 2).

2 4

3

1

Chapter 1. Introduction

7

VM0202HB Rear View

No. Component Description

1 cable tie slot Receives a cable tie to hold the power cable in place.

2 grounding terminal Grounds the VM0202HB to prevent damages from

power surge or static electricity.

3 power jack Receives a power adapter to supply power to the

VM0202HB.

4 cable lock screw for

ATEN LockPro

TM

A universal HDMI cable lock that provides the easiest

way to secure an HDMI cable to most HDMI devices.

5 HDMI output ports The cables from your HDMI display devices plug into

these ports.

6 HDMI input ports The cables from your HDMI source devices plug into

these ports.

7 stereo audio out port Connect an audio output device into this port.

8 stereo line out port Connect the cables from your audio output device into

these ports.

9 audio channel switch Use the switch to set an audio channel from 2 channel

or bypass.

10 IR receiver port Connect the IR Receiver unit included with your

product via this 3.5 mm mini stereo jack.

11 firmware upgrade port Use this port to upgrade the firmware. See The

Firmware Upgrade Utility, page 35.

12 RS-232 serial port Connect a computer or high-end system controller via

this serial port.

62 3

1

4

5

10

11 12

7

8 9

VM0202H / VM0202HB User Manual

8

IR Remote Control

No. Component Description

1 power On / Off Use the On and Off pushbuttons to turn the output

displays on or off – by individual port, or all ports. See

IR Remote Control Operation, page 18.

Note: This pushbutton only works on VM0202H.

2 video output

pushbuttons 1-2

Press the video output pushbuttons 1-2 to select the

display you want to configure, then within 2 seconds

press the input pushbutton 1-2 to select the source for

the display. For detailed instructions, see IR Remote

Control Operation, page 18.

3 video input

pushbuttons 1-2

Press the input pushbuttons 1-2 to select the source

you want to display after you have pressed an output

pushbutton 1-2. You must press the input pushbutton

within 2 seconds after pressing the output pushbutton,

For detailed instructions, see IR Remote Control

Operation, page 18.

1

2

3

9

Chapter 2

Hardware Setup

Rack Mounting

For convenience and flexibility, the VM0202H / VM0202HB can be mounted

on system racks. To rack mount a unit do the following:

Note: The unit used in the diagram below is VM0202H, the procedure for

connecting the VM0202HB is identical to the VM0202H.

1. Using the screws provided in the mounting kit, screw the mounting

bracket to the side of the unit as show in the diagram below:

1. Important safety information regarding the placement of this

device is provided on page 39. Please review it before

proceeding.

2. Make sure that the power to all devices connected to the

installation are turned off.

3. Make sure that all devices you will be installing are properly

grounded.

VM0202H / VM0202HB User Manual

10

2. Screw the bracket into a convenient location on the rack.

Page is loading ...

ATEN VM0202H, VM0202HB User manual

Related papers

Other documents