RESTORER PXRA2676KIT User manual

Brand
RESTORER
Model
PXRA2676KIT
Category
Power tools
Type
User manual
4" RESTORER
Model # PXRA2676
Owner’s Manual
PRODUCT SPECIFICATIONS
Rating:
120 V, 60 Hz AC
Amperes:
3.5 A
Speed:
1,000 – 3,200 RPM (no load)
Sanding roller size:
2
13
/
16
" (72mm) diameter
4" (100mm) wide
Weight:
4 lb. 8 oz. (2.0 kg)
Need Assistance?
Call our toll free customer support line: (888) 848-5175
Technical questions
Replacement parts
Parts missing from package
2
Product specifications ………….………………………………………………………………...
Table of contents ……………………………………………………………………..................
General safety warnings …………………………………………………………………………
Eye, ear & lung protection ……………………………………………………………………….
Electrical safety …………………………………………………………………………………...
Power tool safety ……………………………………………………………………..................
General safety rules ……………………………………………………………………………...
Work area ………………………………………………………………….……………………...
Electrical safety …………………………………………………………………………………...
Personal safety …………………………………………………………………………………...
Power tool use and care .………………………………………………………………………..
Service …………………………………………………………………………………………….
Specific safety rules ……………………………………………………………………………...
Guidelines for extension cords ………………………………………………………………….
Symbols ……………………………………………………………………………………………
Know your restorer ……………………………………………………………..........................
Assembly and operating …………………………………………………………………………
Changing sanding sleeve on roller ……………………………………………………………..
Variable speed control …………………………………………………………………………...
ON/OFF trigger switch …………………………………………………………………………...
Lock-on button ……………………………………………………………………………………
Sanding ……………………………………………………………………………………………
Cleaning the tool …………………………………………………………………………………
Maintenance ………………………………………………………………………………………
Exploded view …………………………………………………………………………………….
Parts list ……………………………………………………………………………………………
Warranty ……………………………………………………………………….………………….
TABLE OF CONTENTS
EYE, EAR & LUNG PROTECTION
This instruction manual includes the following:
General Safety Rules
Specific Safety Rules and Symbols
Functional Description
Assembly
Operation
Maintenance
Accessories
GENERAL SAFETY WARNINGS
WARNING: Before using this tool or any of its accessories, read this
manual and follow all Safety Rules and Operating Instructions. The important
precautions, safeguards and instructions appearing in this manual are not
meant to cover all possible situations. It must be understood that common
sense and caution are factors which cannot be built into the product.
!
SAVE THESE INSTRUCTIONS FOR REFERENCE
3
WARNING: Use hearing protection, particularly during extended
periods of operation of the tool, or if the operation is noisy.
!
!
ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CAN/CSA
STANDARD Z94.3 or ANSI SAFETY STANDARD Z87.1
FLYING DEBRIS can cause permanent eye damage. Prescription
eyeglasses ARE NOT a replacement for proper eye protection.
WARNING: Non-compliant eyewear can cause serious injury if
broken during the operation of a power tool.
4
ELECTRICAL SAFETY
GENERAL SAFETY WARNINGS
WARNING: To avoid electrical hazards, fire hazards or damage to the
tool, use proper circuit protection.
This tool is wired at the factory for 120 V AC operation. It must be
connected to a 120 V AC, 15 A circuit that is protected by a time-delayed
fuse or circuit breaker. To avoid shock or fire, replace power cord
immediately if it is worn, cut or damaged in any way.
SAVE THESE INSTRUCTIONS FOR REFERENCE
WEAR A DUST MASK THAT IS DESIGNED TO BE USED WHEN
OPERATING A POWER TOOL IN A DUSTY ENVIRONMENT.
WARNING: Dust that is created by power sanding, sawing, grinding,
drilling, and other construction activities may contain chemicals that are
known to cause cancer, birth defects, or other genetic abnormalities. These
chemicals include:
Lead from lead-based paints
Crystalline silica from bricks, cement, and other masonry
products
Arsenic and chromium from chemically treated lumber
The level of risk from exposure to these chemicals varies, according to how
often this type of work is performed. In order to reduce exposure to these
chemicals, work in a well-ventilated area, and use approved safety
equipment, such as a dust mask that is specifically designed to filter out
microscopic particles.
!
5
WARNING: Read all safety
warnings and instructions. Failure to
follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or
fumes.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric
shock.
Avoid body contact with earthed or
grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an
increased risk of electric shock if your body is
earthed or grounded.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep the cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric
shock.
When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of a ground fault
circuit interrupter (GFCI) reduces the risk of
electric shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the
switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energizing power tools that have the
switch on invites accidents.
Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
Dress properly. Do not wear loose clothing
or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewelry or long hair can be caught in
moving parts.
POWER TOOL SAFETY
!
SAVE THESE INSTRUCTIONS FOR REFERENCE
6
Personal safety – cont’d
If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool’s operation. If
damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Hold power tool by insulated gripping
surfaces, because the abrasive sleeve may
contact its own cord. Cutting a "live" wire may
make exposed metal parts of the tool "live" and
could give the operator an electric shock.
SERVICE
Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
POWER TOOL SAFETY
SAVE THESE INSTRUCTIONS FOR REFERENCE
7
WARNING: Know your Restorer. Do not
plug in the Restorer until you have read and
understand this Instruction Manual. Learn
the tool’s applications and limitations, as
well as the specific potential hazards related
to this tool. Following this rule will reduce the
risk of electric shock, fire, or serious injury.
Always wear eye protection. Any power
tool can throw foreign objects into your
eyes and cause permanent eye damage.
ALWAYS wear safety goggles (not glasses) that
comply with CAN/CSA Standard Z94.3 or ANSI
safety standard Z87.1. Everyday glasses have
only impact resistant lenses. They ARE NOT
safety glasses.
WARNING: Glasses or goggles not in
compliance with ANSI Z87.1 could cause
serious injury when they break.
WARNING: Always use a dust mask
when sanding or stripping paint.
WARNING: Always use hearing
protection when using this tool, particularly
during extended periods of operation.
WARNING: Always unplug the tool from
the power source before changing the roller,
sanding cylinder, accessory and when
cleaning the tool.
WARNING: FIRE HAZARD:
Never use this tool near explosive
atmosphere or combustible materials. If the
sandpaper hits a nail or any ferrous metal, a
spark could cause an explosion of fire.
WARNING: FIRE HAZARD:
Collected sanding dust from sanding
coatings such as polyurethane, linseed oil
etc. can self-ignite. To reduce the risk, clear
dust frequently from the sanding drum area and
from the surrounding work area. Strictly follow
the cleaning instructions in the Owner’s Manual
and coating manufacturer’s instructions.
WARNING: Always use safety goggles
and a dust mask when using compressed air
to remove sanding dust from the tool.
WARNING: Make sure the roller has
come to a full stop before taking your hands
off the tool. If the roller is still moving, the tool
may move erratically and either damage the
workpiece or cause injury to the user.
Always place the Restorer on its “nose”
(balanced between the front handle and the
roller housing) when the tool is turned OFF and
when storing the tool. This will prevent
inadvertent loss of control if the tool is
accidentally turned ON. It will also avoid the
roller from developing a flat spot if the tool is
stored for long periods of time with weight on
the roller.
Always use two hands when operating the
Restorer. One hand should be used on the front
handle and the other hand should be placed on
the rear handle to operate the switches. Using
both hands will provide better control over the
tool.
Do not wear gloves, neckties or loose clothing.
Secure the workpiece. Use clamps or a vise to
hold the work when practical. It is safer than
using your hand and it frees both hands to
operate the tool.
Do not use this tool on material too small to be
securely held.
Make sure there are no nails or foreign objects
in the part of the workpiece to be sanded or
cleaned.
Always keep hands out of the path of the roller.
Avoid awkward hand positions where a sudden
slip could cause your hand to move into the path
of the roller.
SPECIFIC SAFETY RULES
!
!
!
!
!
SAVE THESE INSTRUCTIONS FOR REFERENCE
!
!
!
!
8
Make sure your extension cord is the proper
size. When using an extension cord, be sure to
use one heavy enough to carry the current the
tool will draw. An undersized cord will cause a
drop in line voltage resulting in loss of power
and overheating. The table at right shows the
correct size to use according to cord length and
nameplate ampere rating. If in doubt, use the
next heavier gauge. The smaller the gauge
number the heavier the cord.
Be sure your extension cord is properly
wired and in good condition. Always replace a
damaged extension cord or have it repaired by a
qualified electrician before using it. Protect your
extension cord from sharp objects, excessive
heat and damp or wet areas.
Use a separate electrical circuit for your
power tools. This circuit must not be less than
14 gauge wire and should be protected with
either a 15A time delay fuse or circuit breaker.
Before connecting the power tool to the power
source, make sure the switch is in the OFF
position and the power source is the same as
indicated on the nameplate. Running at lower
voltage will damage the motor.
WARNING: Repair or replace damaged
or worn extension cords immediately.
Select the appropriate extension cord gauge
and length using the chart at right.
When operating a power tool outdoors, use
an outdoor extension cord marked “W-A” or
“W”. These cords are rated for outdoor use and
reduce the risk of electric shock.
WARNING: Keep the extension cord
clear of the working area. Position the cord
so it will not get caught on the workpiece,
tools or any other obstructions while you are
working with the power tool.
GUIDELINES FOR EXTENSION CORDS
!
MINIMUM GAUGE (AWG) EXTENSION
CORDS (120 V use only)
Ampere rating
Total length in feet
More
than
Not
more
than
7.5 m
(25')
15 m
(50')
30 m
(100')
45 m
(150')
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Applicable
!
SAVE THESE INSTRUCTIONS FOR REFERENCE
9
This symbol designates that this tool Conforms
to UL Std. 60745-1, 60745-2-4 and is Certified
to CAN/CSA Std.C22.2 No. 60745-1, 60745-2-4
by ETL Testing Laboratories, Inc.
3042597
JD2676U
LISTED
V
Volts
A
Amperes
Hz
Hertz
W
Watts
kW
Kilowatts
Microfarads
L
Liters
kg
Kilograms
H
Hours
N/cm
2
Newtons per square
centimeter
Pa
Pascals
OPM
Oscillations per minute
Min
Minutes
S
Seconds
or a.c.
Alternating current
Three-phase alternating
current
Three-phase alternating
current with neutral
Direct current
No load speed
Alternating or direct
current
Class II construction
Splash-proof
construction
Watertight construction
Protective grounding at
grounding terminal,
Class I tools
Revolutions or
reciprocations per
minute
Diameter
Off position
Directional arrow
Warning symbol
Wear your safety
glasses
Wear a dust mask
Wear hearing protection
Fire hazard
Read all instructions
SYMBOLS
WARNING: Some of the following symbols may appear on the Restorer. Study
these symbols and learn their meaning. Proper interpretation of these symbols will
allow for more efficient and safer operation of this tool.
!
10
KNOW YOUR RESTORER
Coarse
sanding sleeve
(2)
Medium
sanding sleeve
(2)
Fine
sanding sleeve
(2)
Air vents
Lock-on
button
Front
handle
Variable speed
control
Roller
ON/OFF
trigger switch
Roller end
cover clamp
Main
handle
Roller end
cover
Roller end
cover hasp
Dust
port
11
CHANGING SANDING SLEEVE ON ROLLER
WARNING: Remove the plug from the
power source before installing or removing a
sanding roller.
1. Lift the two roller end cover hasps (1) away
from the main housing (2) (Fig. 1).
2. Release the RIGHT hasp from the roller
end cover (3).
3. Pull the cover out from the main housing
and flip it toward the front of the tool using
the LEFT hasp as a hinge (Fig 2).
4. Slide the roller (4) off the roller shaft (5).
5. Remove the old sanding sleeve and slide
the new sanding sleeve (6) onto the roller
(4) (Fig. 3).
NOTE: Rotate the roller sleeve counter-
clockwise as you slide the roller sleeve fully
onto the roller. Make sure it is centered on
the roller and is not overhanging one end
of the roller.
6. Slide the roller onto the roller shaft (Fig. 4).
NOTE: The roller can only be installed one
way. When properly installed, the
directional arrow (7) on the end of the roller
will be visible.
7. Reinstall the roller end cover and fasten it
in place with the two roller end cover
hasps.
CAUTION: Make sure the roller end cover
is properly seated onto the main housing
and the hasps snap into place.
VARIABLE SPEED CONTROL
The variable speed control (1) can be rotated to
change the speed at which the roller will rotate
(Fig. 5). Rotate the speed control to the LEFT
(#1) for slowest speed and to the right (MAX) for
the fastest speed.
NOTE: See "SANDING" section of this manual
for recommended speeds.
ASSEMBLY AND OPERATING
!
Fig. 1
1
2
1
3
Fig. 2
Fig. 4
7
Fig. 3
6
4
12
VARIABLE SPEED CONTROL – cont’d
ON/OFF TRIGGER SWITCH
The ON/OFF trigger switch (1) is a single
function switch (Fig. 6). To turn the tool ON,
squeeze the trigger. To turn the tool OFF,
release the trigger.
LOCK-ON BUTTON
The lock-on button (2) is used to lock the
ON/OFF trigger switch in the ON position
(Fig. 7). Locking the trigger switch in the ON
position will reduce hand fatigue when operating
the tool for extended periods of time.
1. To lock the trigger switch in the ON
position, squeeze the trigger (1) to turn the
tool ON.
2. While squeezing the trigger, press the lock-
on button (2) into the handle.
3. While holding the lock-on button into the
handle, release the trigger. At this point,
the tool will remain running.
4. To release the lock-on button to turn the
tool OFF, squeeze and then release the
trigger. The trigger switch will then turn
OFF.
WARNING: Be sure the lock button is not
depressed by cycling the ON/OFF switch
several times or by depressing and releasing
the switch several times before plugging in your
restorer. Damage to your tool or personal injury
may result.
ASSEMBLY AND OPERATING
Fig. 5
1
Fig. 6
1
Fig. 7
1
2
For safety reasons, the operator must
read the sections of this Owner’s
Manual entitled "GENERAL SAFETY
WARNINGS", "POWER TOOL SAFETY",
"SPECIFIC SAFETY RULES",
"GUIDELINES FOR EXTENSION
CORDS" and "SYMBOLS" before using
this Restorer.
Verify the following every time the
Restorer is used:
1. There are no flammable or
explosive materials in the work
area.
2. Restorer cord is not damaged.
3. Safety glasses and dust mask are
being worn.
4. Hearing protection is being worn.
5. Sanding sleeve is the correct type
for the job.
6. Sanding sleeve is in good condition
and is properly installed.
Failure to observe these safety rules will
significantly increase the risk of injury.
WARNING
!
!
13
SANDING
This tool can be used to sand rough material or
to remove paint, varnish or other finishes.
WARNING: Always use safety glasses,
dust mask and hearing protection when
operating this tool. Failure to wear these
protective devices may cause serious
injuries.
WARNING: Never use this tool near
flammable materials. A spark from sanding
hidden fasteners could ignite flammable
materials.
WARNING: An unsecured workpiece
could be thrown toward the operator causing
injury.
WARNING: Clamp or otherwise secure
your workpiece to prevent it from moving under
the Restorer while being sanded.
WARNING: Always use two hands to
operate this tool. One hand should be on the
front handle and the other on the rear
handle. Failure to use two hands may cause
the tool to be difficult to control and possibly
cause serious injury to the operator.
Do NOT cover the cooling vents in the tool. This
will cause the tool to overheat and damage the
tool.
Before starting any sanding project, you should
practice sanding on a scrap workpiece similar to
the item to be sanded. This will allow you to get
the "feel" of the tool and also establish the grit of
the sanding sleeve and tool speed to best suit
the type of material being sanded.
In general, removing heavier finishes and when
sanding rough surfaces, a coarser sanding
sleeve and slower tool speeds are
recommended. Slower speeds will reduce the
heat created while sanding and reduce the
tendency of the sanding sleeve to become
clogged. For sanding smoother surfaces without
finishes, finer sanding sleeves and higher tool
speeds are recommended.
To begin sanding, install the appropriate
sanding sleeve, set the tool speed and squeeze
the trigger switch to turn the tool ON.
NOTE: The sanding sleeve should NOT be in
contact with the workpiece until it has reached
its operating speed.
Once the tool has reached its operating speed,
hold onto the tool with both hands and carefully
bring the sanding sleeve into contact with the
workpiece.
NOTE: When the sanding sleeve contacts the
workpiece, the tool will tend to be pulled forward
away from you. Make sure you have a firm grip
on the tool with both hands.
DO NOT FORCE THE RESTORER. The weight
of the Restorer usually provides adequate
pressure. Let the Restorer and the sandpaper
do the work. Applying added pressure will slow
the motor, increase the wear on the sanding
sleeve and greatly reduce the tool speed. Motor
damage may occur if excessive downward
pressure is applied. It will also create an inferior
finish on sanded work. Any finish or resin on
wood will soften from the frictional heat, causing
the sanding sleeve to become clogged very
quickly. Do not sand in one spot as the sanding
sleeve will remove too much material, making
the surface uneven.
When sanding wood, always move the Restorer
forward and backward with the grain (Fig. 8).
Sanding across the grain will not leave a smooth
surface.
ASSEMBLY AND OPERATING
!
!
!
!
Fig. 8
!
14
SANDING – cont’d
Always keep the tool "moving" when the sanding
sleeve is in contact with the workpiece. This is
particularly important when sanding wood or
other soft materials. Failure to keep the tool
"moving" will result in gouges in the workpiece.
Do not allow sanding dust to accumulate in the
tool. Stop and clean out all loose sanding dust
at regular intervals to prevent unnecessary
buildup that will cause the tool to be inefficient
and to guard against overheating. Refer to
"CLEANING THE TOOL" for details.
Always place the Restorer on its “nose”
(balanced between the front handle and the
roller housing) when the tool is turned OFF and
when storing the tool (Fig. 9). This will prevent
inadvertent loss of control if the tool is
accidentally turned ON. It will also prevent the
roller from developing a flat spot if the tool is
stored for long periods of time with weight on
the roller.
CLEANING THE TOOL
It is important to keep the tool as clean as
possible to reduce the risk of fire and to produce
the best possible sanding results.
WARNING: Always remove the plug
from the power source before removing the
sanding roller and before cleaning the tool.
WARNING: Always wear safety goggles
and a dust mask when using compressed air
to remove sanding dust from the tool.
WARNING: Do not at any time allow
brake fluids, gasoline, petroleum-based
products, penetrating oils, etc. to come in
contact with plastic parts. They contain
chemicals that can damage, weaken or
destroy plastic.
1. Unlatch the roller end cover (Fig. 1).
2. Remove the roller from the tool.
3. Remove the sanding sleeve from the roller.
4. Use compressed air to blow all the loose
sanding dust from the:
roller housing,
roller end cover.
slots in the roller, and
dust chute in the back of the rear
handle.
NOTE: If compressed air is not available, use a
soft DRY long bristled brush to remove the
sanding dust.
Use a clean, dry cloth to remove sanding dust
from the other tool components.
NOTE: Do NOT use any solvents or water on
the cloth.
!
!
!
ASSEMBLY AND OPERATING
Fig. 9
15
GENERAL
WARNING: When servicing, use only
identical replacement parts. Use of any other
replacement parts may create a hazard or
cause product damage.
DO NOT use solvents when cleaning plastic
parts. Most plastics are susceptible to damage
from various types of commercial solvents and
may be damaged by their use. Use a clean cloth
to remove dirt, dust, oil, grease, etc.
WARNING: Do not at any time allow
brake fluids, gasoline, petroleum-based
products, penetrating oils, etc. to come in
contact with plastic parts. They contain
chemicals that can damage, weaken or
destroy plastic.
DO NOT abuse power tools. Abusive practices
can damage the tool as well as the workpiece.
WARNING: DO NOT attempt to modify
tools or create accessories not
recommended. Any such alteration or
modification is misuse and could result in a
hazardous condition leading to possible
serious injury. It will also void the warranty.
It has been found that electric tools are
subjected to accelerated wear and possible
premature failure when they are used on
fiberglass boats and automotive parts,
wallboard, spackling compounds or plaster. The
chips and grindings from these materials are
highly abrasive to electric tool parts such as
bearings, brushes, commutators, etc.
Consequently, it is not recommended that this
tool be used for extended work on any
fiberglass material, wallboard, spackling
compounds or plaster. During any use on these
materials it is extremely important that the tool is
cleaned frequently by blowing the dust out of the
tool with an air jet. See "CLEANING THE TOOL"
section of this manual for details.
WARNING: Always wear safety goggles
or safety glasses with side shields during all
sanding operations. It is critical that you also
wear safety goggles or safety glasses with
side shields and a dust mask while blowing
dust out of the Restorer with an air jet.
Failure to take these safety precautions
could result in permanent eye or lung
damage.
LUBRICATION
All of the bearings in this restorer are lubricated
with a sufficient amount of high grade lubricant
for the life of the unit under normal conditions.
Therefore, no further lubrication is required.
MAINTENANCE
!
!
!
!
EXPLODED VIEW
16
1
23
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
17
WARNING: When servicing, use only original equipment replacement parts. The use of any
other parts may create a safety hazard or cause damage to the Restorer.
WARNING: To assure SAFETY and RELIABILITY of repairs, maintenance and accessories, the
use of any accessory not recommended for use with this tool could be hazardous. Recommended
accessories for use with your tool are available from your local dealer or authorized service center. If
you need assistance regarding accessories, please call the toll-free helpline at 1-866-349-8665
(Monday through Friday 9:00am – 5:00pm Eastern Time).
Any attempt to repair or replace electrical parts on this Restorer may create a safety hazard unless
repairs are performed by a qualified technician. For more information, call the toll-free helpline, at
1-866-349-8665 (Monday through Friday 9:00am – 5:00pm Eastern Time).
Always order by PART NUMBER, not by key number.
Key #
Part #
Part Name
Quantity
1
1190030064
Cord & plug
1
2
3140010054
Cord sleeve
1
3
4030010099
Tapping screw ST3.9x14
2
4
2030050002
Strain relief
1
5
1061260001
Switch
1
6
1130010248
Circuit board
1
7
3011300001
Housing
1
8
4030010106
Tapping screw ST3.9X19
12
9
3150010116
Fan
1
10
1010310001
Rotor
1
11
4010010054
Bearing 6000 2RS
1
12
2040080048
Transmission gear
1
13
2040040116
Gear shaft
1
14
3150070101
Gear cover
1
15
4030010099
Tapping screw ST3.9X14
5
16
4010010043
Bearing 6000 Z
1
17
2040080049
Output gear
1
18
2030170007
bearing washer
1
19
4010010086
Bearing 6002 Z
1
20
2040310051
Coupling sleeve
1
21
2040040117
Output shaft
1
22
6300010003
Roller
2
23
2040310052
Quick coupling sleeve
2
24
4010010084
Bearing 6002 2RS
2
25
4100020010
Spring washer Φ14
1
26
4030010180
Tapping screw ST3.9X10
2
27
2030020269
Bearing washer
2
28
3160010073
Rear cover
1
29
4010010042
Bearing 696
2
30
1020310001
Stator
1
31
4010010053
Bearing 607 2RS
1
32
4030010169
Tapping screw ST3.9X55
2
33
2030030281
Hasp
2
PARTS LIST
!
!
18
Key #
Part #
Part Name
Quantity
34
4030010008
Tapping screw ST2.5X8
4
35
1230010146
Carbon brush
2
36
2030070053
Brush holder
2
37
3160010072
Motor cover
1
38
4030010106
Tapping screw ST3.9X19
3
39
1250010002
Terminal block
1
Rev 1.9 20/07/2016
THREE YEAR LIMITED WARRANTY
PORTER-CABLE will repair, without charge, any defects due to faulty materials
or workmanship for three years from the date of purchase. This warranty does
not cover part failure due to normal wear or tool abuse. For further detail of
warranty coverage and warranty repair information, visit www.portercable.com
or call (888) 848-5175. This warranty does not apply to accessories or damage
caused where repairs have been made or attempted by others. This warranty
gives you specific legal rights and you may have other rights which vary in
certain states or provinces.
In addition to the warranty, PORTER-CABLE tools are covered by our:
1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace
worn parts caused by normal use, for free, any time during the first year after
purchase.
90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with
the performance of your PORTER-CABLE Power Tool, Laser, or Nailer for any
reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
To register your tool for warranty service, visit our website at
www.portercable.com.
LATIN AMERICA: This warranty does not apply to products sold in Latin
America. For products sold in Latin America, see country specific warranty
information contained in the packaging, call the local company or see website for
warranty information.
PARTS LIST
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

RESTORER PXRA2676KIT User manual

Brand
RESTORER
Model
PXRA2676KIT
Category
Power tools
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents