Hushmat 10201 is a damping material used for automotive sound deadening. Here is a summary of its capabilities and use cases based on the information in the instruction manual:
- Reduces road and tire noise by applying the material to the inside of the outer door skin and covering at least 60% of the surface area.
- Eliminates rattles by applying the material to the door frame, covering all access holes.
- Enhances car audio sound experience by reducing vibrations and improving the sound quality of speakers.
- Easy to install by removing the brown release paper and applying the sheet through the access holes in the door frame.
Hushmat 10201 is a damping material used for automotive sound deadening. Here is a summary of its capabilities and use cases based on the information in the instruction manual:
- Reduces road and tire noise by applying the material to the inside of the outer door skin and covering at least 60% of the surface area.
- Eliminates rattles by applying the material to the door frame, covering all access holes.
- Enhances car audio sound experience by reducing vibrations and improving the sound quality of speakers.
- Easy to install by removing the brown release paper and applying the sheet through the access holes in the door frame.
Universal Door Installation Instructions*
(Good, Better, Best)
Remove door panel from door disconnect all hardware and wire harnesses
bet
ween
panel
and door.
Remove plastic environmental barrier from door frame and hold to re-apply after
install is complete.
Note: HushMat Door installation guide is presented as an example of one vehicles door to illustrate the universal
application of HushMat in all vehicle doors. Your trim panels, sheet metal, frame configuration might look different –
however the application of HushMat on a vehicle is consistent. If you are unsure of your ability to disassemble, install and
reassemble your vehicles doors as illustrated we advise you to take your vehicle to a custom installation center near you.
You can search for these custom installation centers on the Zip Code Lookup feature on https://HushMat.com .
Basic Door Installation (“GOOD”)
Apply HushMat Ultra Silver or Black Foil damping material to the inside of the
outer door skin by removing the brown release paper from the Ultra and passing
the sheet through the largest access hole in the frame.
Several ins
t
allers
prefer HushMat Ultra black foil as it does not reflect light and
will not be seen through speaker grills and other holes in your door.
Position the sheet against the outer skin by using the smaller access holes
through door frame. Cover a minimum of 60% of the door skin starting in the
center and work toward the outer edges of the door.
High Performance Door Installation (“BETTER”)
For the highest performance we recommend taking the larger sheets of HushMat
Ultra and apply them to the door frame covering all access holes through the
door. Start on one edge of the door frame and peel back the brown release
paper from the sheet and apply from the top of the frame to the bottom.
The HushMat Ultra also serves as the vapor barrier that you removed.
Carefully cut access slits through the HushMat Ultra where wiring or door
hardware must pass through. Pull wiring or hardware through slits.
Reinstall door speaker and hardware to the door.
Superior Performance Door Installation (“BEST”)
Eliminate the high frequency road, tire and wind noise by installing HushMat
Silencer Megabond ¼” sound absorbing foam to the back of the door panel
Lay the door panel on a table with the back of the panel facing up. Lay one
sheet of Silencer Megabond ¼” foam against the door panel with the white
release paper on the foam. Place the edge of the foam just inside the fasteners
or clips that secure the panel to the door.
Cut around all panel fastening points, speaker grill, wire harness pass through of
any
mechanical
hardware that will be attached to the vehicle door by slitting the
foam and pulling the device through the foam.
Secure all hardware and electrical connections from the door panel to the door
and place the panel back onto the vehicle. Test each device to ensure function
before securing the panel.
Cut away any foam that overhangs the edges of the door panel with scissors
or a utility knife. Hand press the foam to the panel across the surface.
Starting at one straight edge peel back the white release paper and press the
sheet onto the straight edge of the door panel. Peel back the release
paper completely from the sheet and work around the outer edges of the door
panel applying finger/hand pressure to the foam surface.
Secure the door panel to the door and the door installation is complete.
Repeat the above steps for each door in your vehicle.
HushMat Product used – Good, Better and Best Installation
Good -- Basic Door Install- 2 Doors Goal solid door slam/eliminate rattles
HushMat Ultra Damping material One (1) –10200/10201 (Black or Silver Foil)
Ten (10) Square feet. (5 Sq. Ft. per Door)
Better - Door Install- 2 Doors
HushMat Ultra Damping Material (Black or Silver Foil)
Two (2) 10200/10201 Door Kits (10 Sq. Ft. per door)
Best - Superior Performance Door Install- 2 Doors for ultimate car audio sound experience
HushMat Ultra Damping Material (Black or Silver foil)
Two (2) 10200/10201 Door Kits (10 Sq. Ft. per Door)
HushMat Silencer Megabond ¼” sound absorbing foam
20200 One (1) - 23” x 36” Sheet per door
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Hushmat 10201 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Hushmat 10201 is a damping material used for automotive sound deadening. Here is a summary of its capabilities and use cases based on the information in the instruction manual:
- Reduces road and tire noise by applying the material to the inside of the outer door skin and covering at least 60% of the surface area.
- Eliminates rattles by applying the material to the door frame, covering all access holes.
- Enhances car audio sound experience by reducing vibrations and improving the sound quality of speakers.
- Easy to install by removing the brown release paper and applying the sheet through the access holes in the door frame.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Arrow GS83 Installation guide
-
Chrysler 2017 Pacifica User manual
-
Hybrid Audio Technologies Imagine I69-2 User manual
-
Porsche 911 GT2 - Quick start guide
-
Hybrid Audio Technologies Imagine I69-2 Installation Manual & User's Reference
-
Era Replica Automobiles 427 ROADSTER User manual
-
Opel ASTRA Owner's manual
-
-
Porsche 911 CARRERA 4 CABRIOLET User manual
-
Hybrid Audio Technologies Clarus C61-2 User manual
