Page is loading ...
ATTENTION:
Do not use the equipment
without rst reading the
instruction manual.
SPIN
OPERATOR FOR
SOCIAL DOOR PIVOTING
Technical manual
P30194 - 09/2022
Rev. 1
Manufactured by: Motoppar Indústria e Comércio de Automatizadores Ltda
Av. Dr. Labieno da Costa Machado, 3526 - Distrito Industrial - Garça - SP - CEP 17406-200 - Brasil
CNPJ: 52.605.821/0001-55
www.ppa.com.br | +55 14 3407 1000
2 3
IMPORTANT SAFETY INSTRUCTIONS
Recommendation:
For the installation of the equipment, it is important that the installer
specialist PPA follow all instructions cited in this MANUAL TECHNICAL
and USER MANUAL.
With the USER MANUAL, the installer must present all the information,
uses and safety items of the equipment to the user.
Before using the SPIN SOCIAL DOOR OPERATOR, read and strictly
follow all instructions contained in this manual.
- Before installing the automate, make sure that the network local
electrical power complies with that required on the equipment
identification label. Connect the power cord, only to sockets
connected to the grounding network;
- Do not turn on the mains until installation / maintenance is completed
completed. Always make the electrical connections of the board with
the electrical network turned off;
- After installation, make sure that the door parts do not fall apart
extend along the roads and the public footpath;
- Under no circumstances eliminate the grounding pin of the plug. Do
not use adapters that eliminate this connection Earth. It is mandatory
to use the Earth pin.
- The equipment is intended to be installed at a height of at least 2.5
m above floor level or other access level.
INDEX
Important Safety Instructions ...............................................................................................3
Tools required for installation ............................................................................................... 4
Electrical installation ............................................................................................................ 4
Care with the electrical installation ...................................................................................... 5
Technical characteristics ......................................................................................................6
Installation and fixation of the operator ...............................................................................7
Arm fixation ..............................................................................................................7
Fixing the operator on the wall ................................................................................. 7
How to fix the guide to the door ................................................................................ 9
Photocell .................................................................................................................10
Closing the operator cover ....................................................................................11
Maintenance ...................................................................................................................... 12
Defects, probable causes and corrections ............................................................12
4 5
TOOLS REQUIRED FOR INSTALLATION
Below are some tools needed to install the operator:
ELECTRICAL INSTALLATION
For electrical installation, the network must contain the following characteristics:
- 127V or 220V electrical network;
- Have 5A circuit breakers in the electric power distribution box;
- 3/4" diameter conduits between the electrical power distribution box and the total
shutdown device;
- 3/4" diameter conduits between the total shutdown device and the operator
connection point;
- 1/2" diameter conduits for external and optional pushbuttons;
- 1/2" diameter conduits for safety photocells (mandatory).
PENCIL
SCREWDRIVER
SAW
ARCH
FRAME
UNIVERSAL
PLIERS
ALLEN WRENCH
3, 4 and 6mm
HAMMER
PHILIPS KEY
CUTTING
PLIERS
10mm CANNON
WRENCH
DRILLING
MACHINE
STAR KEY
PEAK
PLIERS
MOUTH KEY 10, 13,
22 and 28mm
COMMON LEVEL
HOSE
LEVEL
STAIRS
RATCHET
CARE WITH THE ELECTRICAL INSTALLATION
To avoid damage to the wiring, it is important that all conductors are correctly
attached to the operator. The passage of the wiring must be done through conduits,
passing internally through the base of the floor, ensuring that none of the wiring
conductors is trapped and damaged.
IMPORTANT
The instrument shall be powered via a residual differential current (DR)
device with a rated residual operating current exceeding 30 mA.
6 7
INSTALLATION AND FIXATION OF THE OPERATOR
ARM FIXATION
Fit the articulated arm on the gearmotor shaft and, using an Allen key, secure it
with the screw that comes with the kit.
FIXING THE OPERATOR ON THE WALL
Fix the operator leaving a distance from the turning point of the door to the 350mm
motor output shaft.
PARAMETER AND TECHNICAL CHARACTERISTICS
OPERATOR TYPE PIVOTING PIVOTING PIVOTING PIVOTING
MODEL SINGLE-PHASE SINGLE-PHASE SINGLE-PHASE SINGLE-PHASE
RATED VOLTAGE 220 V 220 V 127 V 127 - 220 V
NOMINAL
FREQUENCY 60 Hz 50 Hz 60 Hz 60 Hz
RATED POWER 200 W 330 W 360 W 35 W
ENGINE
ROTATION 3492 rpm 2910 rpm 3492 rpm 1200 rpm
NOMINAL CHAIN 1,7 A 2,4 A 3,4 A 0,5 A
REDUCTION 1:111,5 1:111,5 1:111,5 1:111,5
LINEAR SPEED 1,6 m/minute 1,3 m/minute 1,6 m/minute 0,6 m/minute
MANEUVERS 240 cycles hour 240 cycles hour 240 cycles hour Intense
DEGREE OF
PROTECTION IPX 0 IPX 0 IPX 0 IPX 0
RAIL Aluminum Aluminum Aluminum Aluminum
TEMPERATURE
RANGE
-5°C
+50 °C
-5°C
+50 °C
-5°C
+50 °C
-5°C
+50 °C
TYPE OF
INSULATION Class B, 130 ° C Class B, 130 ° C Class B, 130 ° C Class B, 130 ° C
TECHNICAL CHARACTERISTICS
350 mm
8 9
If the door has an internal opening, fix the operator so that the drive arm is a little
above the top of the door leaf.
If the door has na external opening, fix the operator so that the drive arm is a little
below the top of door leaf.
HOW TO FIX THE GUIDE TO THE DOOR
After fixing the operator with the drive arm, fix the aluminum guide to the door so
that the actuation arm does not go over the limit and does not come out outside
the guide (fix the aluminum guide in the center of the door).
NOTE: Manually check if the door opens and closes correctly without friction.
Before fixing the guide to the sheet, check that the drive arm does not exceed the
ends.
DRIVE ARM MUST
BE ABOVE THE TOP OF THE LEAF
DRIVE ARM MUST
BE BELOW THE TOP OF THE LEAF
ALUMINUM GUIDE
10 11
VERMELHO
PRETO
AZUL
LARANJA
PHOTOCELL
Fixing and connecting the photocell
1. Pass 1 4-way cable going from the TX to the board, passing through the rail and
fixed with clamps.
2. Pass 1 4-way cable going from RX to the board, passing through the rail and
fixed with clamps.
The command for activating the photocell must be made from an NC (Normally
Closed) contact, that is, for the board to receive a photocell command, the
connection between FOTO and GND of the CN6 connector must be opened.
Precautions
- Do not install the receiver unit facing directly towards the sun;
- Make sure that the side with the wire exit is facing down;
TX RX
30 cm
Photocell wiring diagram
CLOSING THE OPERATOR COVER
After all connections and adjustments have been made, place the board cover,
close the operator cover and secure it with 2 M5 x 10 screws.
Then glue the PPA sticker, as shown in the figure.
SCREW S M5 X10
RED
ORANGE
BLACK
BLUE
12
MAINTENANCE
Before any Maintenance, remove the power cable from the mains.
DEFECTS, PROBABLE CAUSES AND CORRECTIONS
Some DEFECTS, PROBABLE CAUSES AND CORRECTIONS will be mentioned,
which may occur in your Operator, if Maintenance needs to occur.
DEFECTS PROBABLE CAUSES CORRECTIONS
Door opening and closing
alone
-Dirt on the rail.
-Dirt on the door guide.
-Radar deregulated, is
picking up the movement
of the leaf.
-Clean Rail.
-Clean door guides.
-Adjust radar sensitivity.
Door opening slowly -Lack of electricity.
-Activate the radar and
wait for the door to open
and close slowly.
Door opened and didn't
close -Obstructed photocell. -Unclog the photocell.
/
