Chief MSB6306 Installation guide
- Category
- Flat panel accessories
- Type
- Installation guide
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Medium Flat Panel Interface Bracket
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
MSB6306
MSB6306 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm). Do
not install drywall anchors into the seam between drywall
pieces.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the MSB6306 up to (and
including) the display does not exceed 125 lbs (56.7 kg).
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
DIMENSIONS
16.83
428
13.00
330
11.71
297
1.97
50
4.38
111
1.97
50
4.48
114
3.94
100
3.94
100 400 x 400
PATTERN
300 x 300
PATTERN
MOUNTING BUTTONS FIT
INTO SLOTS ON MOUNT
2" OR 4" VERTICAL
OFFSET AVAILABLE
FOR NON-CENTERED
MOUNTING PATTERNS
1.09
ADDED DEPTH
(20mm SPACERS)
28
.70
ADDED DEPTH
(10mm SPACERS)
18
Installation Instructions MSB6306
3
TOOLS / PARTS FOR INSTALLATION
ASSEMBLY AND INSTALLATION
1. Attach mounting buttons (D) to interface bracket (A) using
four #10-24 x 1/2" button head cap screws (E) and a 1/8"
hex key (H). (See Figure 1)
NOTE: 2" or 4" offset holes available to use for non-centered
mounting patterns. (See Figure 1)
Figure 1
2. Select proper screws (B and C) and spacers (F and G) to
use for specific display based on mounting hole depth and
location.
3. Place four spacers (F or G) over mounting holes on back of
display. (See Figure 2)
4. Use four Phillips pan machine screws (B or C) to secure
interface bracket (A) to display. (See Figure 2)
NOTE: Use interior mounting holes for 300x300 mounting
patterns. (See Figure 2)
Figure 2
5. Complete installation following the installation instructions
provided with mount.
1/8"
(Included) A (1)
[Interface
Bracket]
B (4)
M8 X 25mm
D (4)
[mounting button]
E (4)
#10-24 x 1/2"
H (1)
1/8"
C (4)
M8 x 35mm F (4)
M20
G (4)
M10
(E) x 4
(A)
(D) x 4
1
2" or 4" offset
holes
4
(B or C) x 4
(F or G) x 4
3
300 x 300
holes
300 x 300
holes
MSB6306 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002278 Rev00
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
12/12
-
1
-
2
-
3
-
4
Chief MSB6306 Installation guide
- Category
- Flat panel accessories
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI