Anybus AWB5141 User manual

Brand: Anybus

Model: AWB5141

Category: Routers

Type: User manual

Anybus® Wireless Access Point IP30 with Mesh

USER MANUAL

SCM-1202-155

Version 1.1

Publicaon date 2022-06-02

ENGLISH

Important User Informaon

Disclaimer

The informaon in this document is for informaonal purposes only. Please inform HMS Networks of any

inaccuracies or omissions found in this document. HMS Networks disclaims any responsibility or liability for any

errors that may appear in this document.

HMS Networks reserves the right to modify its products in line with its policy of connuous product

development. The informaon in this document shall therefore not be construed as a commitment on the

part of HMS Networks and is subject to change without noce. HMS Networks makes no commitment to update

or keep current the informaon in this document.

The data, examples and illustraons found in this document are included for illustrave purposes and are only

intended to help improve understanding of the funconality and handling of the product. In view of the wide

range of possible applicaons of the product, and because of the many variables and requirements associated

with any parcular implementaon, HMS Networks cannot assume responsibility or liability for actual use

based on the data, examples or illustraons included in this document nor for any damages incurred during

installaon of the product. Those responsible for the use of the product must acquire sucient knowledge in

order to ensure that the product is used correctly in their specic applicaon and that the applicaon meets all

performance and safety requirements including any applicable laws, regulaons, codes and standards. Further,

HMS Networks will under no circumstances assume liability or responsibility for any problems that may arise as

a result from the use of undocumented features or funconal side eects found outside the documented scope

of the product. The eects caused by any direct or indirect use of such aspects of the product are undened and

may include e.g. compability issues and stability issues.

Contact Informaon

Postal address:

Box 4126

300 04 Halmstad, Sweden

E-Mail: inf[email protected]

Table of Contents

1. Preface .................................................................................................................................. 1

1.1. About This Document ........................................................................................................ 1

1.2. Document Convenons ..................................................................................................... 1

1.3. Trademarks ..................................................................................................................... 2

2. Safety .................................................................................................................................... 3

2.1. General Safety ................................................................................................................. 3

2.2. Intended Use ................................................................................................................... 3

3. Preparaon ............................................................................................................................ 4

3.1. Support and Resources ...................................................................................................... 4

4. Installaon ............................................................................................................................. 5

4.1. DIN Rail Mounng ............................................................................................................ 5

4.2. Connect Ground Screw ...................................................................................................... 6

4.3. Connect to Power ............................................................................................................. 6

4.3.1. Connect to Power via Terminal Block ............................................................................ 7

4.3.2. Connect to Power via Ethernet PoE .............................................................................. 8

4.4. Connect to Ethernet .......................................................................................................... 9

4.5. Connect Antennas ............................................................................................................ 9

5. Conguraon ......................................................................................................................... 10

5.1. Before You Begin Conguraon .......................................................................................... 10

5.2. Access the Web Management Interface ............................................................................... 10

5.3. Congure the Country/Region Sengs ................................................................................ 11

5.4. Submit and Save Conguraon .......................................................................................... 11

5.5. Factory Reset .................................................................................................................. 12

5.6. System .......................................................................................................................... 13

5.6.1. Informaon ............................................................................................................ 13

5.6.2. Login Seng ........................................................................................................... 13

5.6.3. Network Seng ....................................................................................................... 13

5.6.4. Date and Time ......................................................................................................... 14

5.6.5. DHCP Server ........................................................................................................... 14

5.7. Ethernet Port .................................................................................................................. 15

5.7.1. Port Status .............................................................................................................. 15

5.7.2. Port Seng ............................................................................................................. 15

5.7.3. Trac Control ......................................................................................................... 15

5.8. Wireless LAN .................................................................................................................. 16

5.8.1. WLAN Status ........................................................................................................... 16

5.8.2. WLAN Seng .......................................................................................................... 17

5.8.3. Mul SSID .............................................................................................................. 19

5.8.4. Mesh Sengs ......................................................................................................... 20

5.8.5. WLAN Security ........................................................................................................ 21

5.8.6. Advanced ............................................................................................................... 21

5.8.7. Radius Server .......................................................................................................... 22

5.8.8. Cercate File (Client Mode) ...................................................................................... 22

5.9. Security ......................................................................................................................... 22

5.9.1. Access Control ......................................................................................................... 22

5.9.2. Outbound Firewall ................................................................................................... 22

5.9.3. NAT Seng ............................................................................................................. 23

5.9.4. OpenVPN ............................................................................................................... 24

5.9.5. IPSec Seng ........................................................................................................... 25

Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1

5.9.6. L2TP Seng ............................................................................................................ 25

5.10. Warning ....................................................................................................................... 26

5.10.1. Ping Watchdog ...................................................................................................... 26

5.10.2. Syslog Seng ........................................................................................................ 26

5.11. Diagnoscs ................................................................................................................... 27

5.11.1. Event Logs ............................................................................................................ 27

5.11.2. ARP Table ............................................................................................................. 27

5.11.3. Ping ..................................................................................................................... 27

5.11.4. Trace Route ........................................................................................................... 28

5.11.5. Network Stascs .................................................................................................. 28

5.11.6. Associaon List ...................................................................................................... 28

5.12. Backup/Restore ............................................................................................................. 28

5.12.1. WEB Backup and Restore ......................................................................................... 28

5.13. Firmware Upgrade ......................................................................................................... 29

5.13.1. WEB Firmware Upgrade .......................................................................................... 29

5.14. Reset to Default ............................................................................................................. 30

6. Verify Operaon ..................................................................................................................... 31

6.1. Front Panel LED ............................................................................................................... 31

7. Technical Data ........................................................................................................................ 32

7.1. Technical Specicaons .................................................................................................... 32

8. Reference Guides ................................................................................................................... 33

8.1. Wireless Technology Basics ............................................................................................... 33

Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1

1. Preface

1.1. About This Document

This document describes how to install and congure Anybus® Wireless Access Point IP30 with Mesh.

For addional documentaon and soware downloads, FAQs, troubleshoong guides and technical support,

please visit www.anybus.com/support.

1.2. Document Convenons

Lists

Numbered lists indicate tasks that should be carried out in sequence:

1. First do this

2. Then do this

Bulleted lists are used for:

• Tasks that can be carried out in any order

• Itemized informaon

User Interacon Elements

User interacon elements (buons etc.) are indicated with bold text.

Program Code and Scripts

Program code and script examples

Cross-References and Links

Cross-reference within this document: Document Convenons

External link (URL): www.anybus.com

Preface Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1 Page 1 of 36

Safety Symbols

WARNING

Instrucon that must be followed to avoid a risk of death or serious injury.

WARNING

Instrucon à suivre pour éviter tout risque de décès ou de blessure grave.

CAUTION

Instrucon that must be followed to avoid a risk of personal injury.

CAUTION

Instrucon à suivre pour éviter tout risque de blessure.

IMPORTANT

Instrucon that must be followed to avoid a risk of reduced funconality and/or damage to the

equipment, or to avoid a network security risk.

Informaon Symbols

NOTE

Addional informaon which may facilitate installaon and/or operaon.

TIP

Helpful advice and suggesons.

1.3. Trademarks

Anybus® is a registered trademark of HMS Networks.

All other trademarks menoned in this document are the property of their respecve holders.

Anybus® Wireless Access Point IP30 with Mesh Trademarks

Page 2 of 36 SCM-1202-155 Version 1.1

2. Safety

2.1. General Safety

CAUTION

Ensure that the power supply is turned o before connecng it to the equipment.

CAUTION

Assurez-vous que l’alimentaon électrique est coupée avant de la brancher sur l’équipement.

CAUTION

Connecng power with reverse polarity or using the wrong type of power supply may damage the

equipment. Make sure that the power supply is connected correctly and of the recommended type.

CAUTION

Le fait de brancher l’alimentaon avec une polarité inversée ou d’uliser le mauvais type

d’alimentaon peut endommager l’équipement. Assurez-vous que l’alimentaon électrique est

correctement branchée et conforme au type recommandé.

CAUTION

This equipment contains parts that can be damaged by electrostac discharge (ESD). Use ESD

prevenon measures to avoid damage.

CAUTION

Cet équipement conent des pièces qui peuvent être endommagées par une décharge

électrostaque (ESD). Appliquez les mesures de prévenon ESD pour éviter les dommages.

2.2. Intended Use

The intended use of this equipment is to provide wireless LAN connecvity. The equipment receives and

transmits data on various physical levels and connecon types.

If this equipment is used in a manner not specied by the manufacturer, the protecon provided by the

equipment may be impaired.

Safety Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1 Page 3 of 36

3. Preparaon

3.1. Support and Resources

For addional documentaon and soware downloads, FAQs, troubleshoong guides and technical support,

please visit www.anybus.com/support.

TIP

Have the product arcle number available, to search for the product specic support web page. You

nd the product arcle number on the product cover.

Anybus® Wireless Access Point IP30 with Mesh Preparaon

Page 4 of 36 SCM-1202-155 Version 1.1

4. Installaon

4.1. DIN Rail Mounng

Figure 1. DIN rail mounng opon

1. Fasten the DIN clip with 3 (M3x6 at head) screws on the rear side of the access point.

2. Insert the upper end of the DIN rail clip into the DIN rail.

3. Push the boom of the DIN rail clip into the DIN rail.

Installaon Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1 Page 5 of 36

4.2. Connect Ground Screw

IMPORTANT

To avoid system damage, the equipment should be connected to ground.

Figure 2. Connect ground screw

• Establish a direct connecon between the ground screw and the grounding surface prior to connecng

devices.

4.3. Connect to Power

CAUTION

Ensure that the power supply is turned o before connecng it to the equipment.

CAUTION

Assurez-vous que l’alimentaon électrique est coupée avant de la brancher sur l’équipement.

CAUTION

Connecng power with reverse polarity or using the wrong type of power supply may damage the

equipment. Make sure that the power supply is connected correctly and of the recommended type.

CAUTION

Le fait de brancher l’alimentaon avec une polarité inversée ou d’uliser le mauvais type

d’alimentaon peut endommager l’équipement. Assurez-vous que l’alimentaon électrique est

correctement branchée et conforme au type recommandé.

Anybus® Wireless Access Point IP30 with Mesh Connect Ground Screw

Page 6 of 36 SCM-1202-155 Version 1.1

4.3.1. Connect to Power via Terminal Block

IMPORTANT

Use a power supply of 10-60 VDC for terminal block and 48 VDC for PoE.

Max power consumpon: 11.5 W

Figure 3. Connect to power via terminal blo

P-

10-60 VDC (terminal block) Max. 11.5 W

P+

1. Insert the posive and negave wires into the P- and P+ contact on the terminal block.

2. Tighten the 2 wire-clamp screws.

3. Connect the power wires to a DC power supply.

Connect to Power Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1 Page 7 of 36

4.3.2. Connect to Power via Ethernet PoE

Figure 4. Connect to power via Ethernet PoE

Port Funcon Power

2 PD WAN 1 Gbit/s PoE enabled IEEE 802.3af (48 VDC PoE)

• Connect the access point to an Ethernet network via the WAN PoE enabled port.

Anybus® Wireless Access Point IP30 with Mesh Connect to Power

Page 8 of 36 SCM-1202-155 Version 1.1

4.4. Connect to Ethernet

Figure 5. Connect to Ethernet

Port Funcon Speed

1 LAN 1 Gbit/s

• Connect the access point to an Ethernet network via the LAN port.

4.5. Connect Antennas

Placement Type

ANT 1 WLAN 1, RP-SMA connector, female

ANT 2 WLAN 2, RP-SMA connector, female

Connect to Ethernet Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1 Page 9 of 36

5. Conguraon

5.1. Before You Begin Conguraon

The access point is congured through web management.

NOTE

The switch default IP address is hp://192.168.10.1/.

NOTE

The default switch login user name is admin and the password is admin.

5.2. Access the Web Management Interface

Prepare for conguring the switch sengs via the web management interface.

Before You Begin

1. Connect the access point to your computer.

2. Connect the access point to power.

3. To link your computer with the access point, make sure that the IP address of the computer is located in the

same subnet as the switch default IP address.

Procedure

Access the web management interface:

1. In your browser, type hp://IP address and press Enter.

The web-based management interface login screen appears.

2. In the login screen, enter user name and password.

3. Click OK.

The web-based management interface welcome page appears.

To Do Next

•Congure the access point.

Anybus® Wireless Access Point IP30 with Mesh Conguraon

Page 10 of 36 SCM-1202-155 Version 1.1

5.3. Congure the Country/Region Sengs

IMPORTANT

To comply with the Radio Equipment Direcve (RED) and local radio regulaons you must congure

the country/region sengs before the access point is brought into use.

Procedure

Congure the Country sengs.

Figure 6. Country sengs

In the web management interface:

1. Navigate to the WLAN Sengs tab.

2. Select your country/region from the Country drop-down menu.

3. Press Submit buon for the seng to take eect.

5.4. Submit and Save Conguraon

To apply changes made on a conguraon page/tab, click Submit at the boom of the page.

To discard the changes, click Cancel.

Some pages have addional buons that are described in the respecve secons in this manual.

To save changed sengs permanently, click Save at the top of the conguraon page. The recent changes will

otherwise be discarded if the access point is rebooted.

Figure 7. Web Management Inteface, top menu

Congure the Country/Region Sengs Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1 Page 11 of 36

5.5. Factory Reset

Reset the access point to its factory sengs.

Figure 8. Factory reset buon

1. Ensure that the access point is powered on.

2. Use a pointed object, such as a ballpoint pen, to press and hold the reset buon for >10 seconds.

Result

• Once the reset buon is released, the access point reboots automacally.

• When the access point has successfully rebooted, the SYS LED turns green.

Anybus® Wireless Access Point IP30 with Mesh Factory Reset

Page 12 of 36 SCM-1202-155 Version 1.1

5.6. System

5.6.1. Informaon

Figure 9. System conguraon page

System Name Name of the unit Default: AP

System Descripon A short descripon of the unit for easier idencaon Default: WLAN AP

Soware Version The currently installed rmware version

MAC Address MAC address of the Ethernet network interface

IP Address IP Address of the Ethernet network interface

Subnet Mask Subnet mask of the Ethernet network interface

5.6.2. Login Seng

IMPORTANT

Seng a secure password for the unit is strongly recommended.

User Name / Guest Name Names for the normal user account and the guest account Default: admin/guest

New Password Enter a password for accessing the web interface

Conrm Password Re-type the new password again to conrm it

5.6.3. Network Seng

Table 1. IPv4 Conguraon

IP Assignment/Type Select stac or dynamic IP addressing (DHCP)

IP Address Stac IP address for the unit Default: 192.168.10.1

Subnet Mask Subnet mask when using stac IP Default: 255.255.255.0

Gateway IP Address Default gateway when using stac IP Default: 0.0.0.0.

DNS 1 IP address of primary DNS server when using stac IP

DNS 2 IP address of secondary DNS server when using stac IP

System Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1 Page 13 of 36

Table 2. WAN Seng (Router Mode)

WAN Access Type Select stac or dynamic IP addressing (DHCP)

IP Address Stac IP address for the unit Default: 192.168.1.1

Subnet Mask Subnet mask when using stac IP Default: 255.255.255.0

Gateway IP Address Default gateway when using stac IP Default: 0.0.0.0.

DNS 1 IP address of primary DNS server when using stac IP

DNS 2 IP address of secondary DNS server when using stac IP

5.6.4. Date and Time

Current Time Set the date and me manually

Get PC Time Click to update the date and me from the connected PC

Time Zone Select the desired me zone

NTP When enabled, the date and me will be updated automacally from a specied NTP server. Select an NTP

server in the dropdown list or enter the IP address for the NTP server.

5.6.5. DHCP Server

IMPORTANT

Do not enable DHCP Server if there is already an acve DHCP server on the network, as this may

result in IP address conicts.

DHCP Seng Enable/disable the internal DHCP server

IP Address Start

Set the range of IP addresses that can be allocated by the DHCP Server

IP Address End

Subnet Mask Subnet mask for the DHCP Server Default: 255.255.255.0

Gateway Default gateway for the DHCP Server.

WIN S1 IP address for primary WINS Server

WIN S2 IP address for secondary WINS Server

Primary DNS Server IP address of primary DNS server

Secondary DNS Server IP address of secondary DNS server

Lease Time Maximum DHCP lease me in minutes (range: 15-44640 minutes) Default: 1440

Table 3. DHCP Leased Entries

IP Address IP address assigned by the DNS server

MAC Address MAC Address of the node

Time to expire(s) Remaining DHCP lease me for the node

Anybus® Wireless Access Point IP30 with Mesh System

Page 14 of 36 SCM-1202-155 Version 1.1

5.7. Ethernet Port

Figure 10. Ethernet Port conguraon page

5.7.1. Port Status

Port Ethernet port number (label)

Link Link Up = Ethernet link established Link Down = no Ethernet link

Speed/Duplex Speed (10/100/1000 Mbit/s) and duplex mode (Half/Full) for the port.

5.7.2. Port Seng

Port Ethernet port number (label)

State Enable or disable this port Default: Enable

Speed/Duplex Select the speed and duplex mode for the port. Ports 1–2 (Gigabit Ethernet) can be set to AutoNegoaon (1

Gbit/s), 100 Full and 100 Half. Default: AutoNegoaon

5.7.3. Trac Control

Enable Trac Control Enable/disable trac control

Outgoing Rate Limit Maximum outgoing data rate Default: 1024000 kbit/s

Outgoing Burst Maximum outgoing burst size Default: 20 kBytes

Ethernet Port Anybus® Wireless Access Point IP30 with Mesh

SCM-1202-155 Version 1.1 Page 15 of 36

5.8. Wireless LAN

Figure 11. WLAN conguraon page

5.8.1. WLAN Status

Operaon Mode Operaon mode of the WLAN interface. See WLAN Seng (page 17).

Wireless Mode WLAN mode

SSID SSID of the WLAN interface

Encrypon Encrypon mode used

ACK Timeout For long distance connecons, typically point-to-point, acknowledgment (ACK) meout can be set manually to

avoid excessive retransming.

WMM Enable WMM enabled/disabled

Noise Floor Background noise level (dBm)

Anybus® Wireless Access Point IP30 with Mesh Wireless LAN

Page 16 of 36 SCM-1202-155 Version 1.1

Page is loading ...

Anybus AWB5141 User manual

Brand: Anybus

Model: AWB5141

Category: Routers

Type: User manual

Download PDF

report

Anybus AWB5141 User manual

Anybus AWB5141 User manual

Related papers

Other documents