Gigabyte GA-AX370-Gaming Owner's manual

Brand: Gigabyte

Model: GA-AX370-Gaming

Type: Owner's manual

To reduce the impacts on global warming, the packaging materials of this product

are recyclable and reusable. GIGABYTE works with you to protect the environment.

For more product details, please visit GIGABYTE's website.

GA-AX370-Gaming

User's Manual

Rev. 1001

12ME-AX37GM-1001R

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without prior notice.

No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or

by any means without GIGABYTE's prior written permission.

For quick set-up of the product, read the Quick Installation Guide included with the product.

In order to assist in the use of this product, carefully read the User's Manual.

For product-related information, check on our website at: http://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means

the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard

BIOS, drivers, or when looking for technical information.

Example:

Motherboard

GA-AX370-Gaming

Mar. 17, 2017

Motherboard

GA-AX370-Gaming

- 3 -

Table of Contents

GA-AX370-Gaming Motherboard Layout ........................................................................4

Chapter 1 Hardware Installation .....................................................................................5

1-1 Installation Precautions .................................................................................... 5

1-2 ProductSpecications ...................................................................................... 6

1-3 Installing the CPU ............................................................................................ 9

1-4 Installing the Memory ....................................................................................... 9

1-5 Installing an Expansion Card ......................................................................... 10

1-6 Back Panel Connectors .................................................................................. 10

1-7 Internal Connectors ........................................................................................ 12

Chapter 2 BIOS Setup ..................................................................................................20

2-1 Startup Screen ............................................................................................... 20

2-2 M.I.T. .............................................................................................................. 21

2-3 System ........................................................................................................... 25

2-4 BIOS ............................................................................................................... 26

2-5 Peripherals ..................................................................................................... 29

2-6 Chipset ........................................................................................................... 31

2-7 Power ............................................................................................................. 32

2-8 Save & Exit ..................................................................................................... 34

Chapter 3 Appendix ......................................................................................................35

3-1 ConguringaRAIDSet .................................................................................. 35

3-2 DriversInstallation .......................................................................................... 37

RegulatoryStatements .............................................................................................. 38

Contact Us ................................................................................................................ 40

- 4 -

GA-AX370-Gaming Motherboard Layout

* The box contents above are for reference only and the actual items shall depend on the product package you obtain.

The box contents are subject to change without notice.

Box Contents

5GA-AX370-Gaming motherboard 5Quick Installation Guide

5Motherboard driver disk 5Four SATA cables

5User's Manual 5I/O Shield

Socket AM4

KB_MS_USB30

CPU_FAN

SYS_FAN1

ATX

F_USB30_2

AUDIO

DDR4_4

DDR4_2

BAT

ATX_12V

CODEC

CLR_CMOS

M_BIOS

Realtek®

GbE LAN

PCIEX16

PCIEX1_2

iTE®

Super I/O

GA-AX370-Gaming

F_PANEL

F_AUDIO

SPDIF_O

PCIEX1_1

SATA3

USB30_LAN

HDMI

0 2 4 6

1 3 5 7

AMD

X370

F_USB2TPM

R_USB30

B_BIOS

R_USB31

M2F_32G

80 60 42110

DDR4_3

DDR4_1

F_USB30_1

SYS_FAN3_PUMP

PCIEX1_3

PCIEX4

SYS_FAN2

F_USB1COMA

ASMedia®

USB 3.1 Gen 2

Controller

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damagedasaresultofelectrostaticdischarge(ESD).Priortoinstallation,carefullyreadtheuser's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Priortoinstallation,donotremoveorbreakmotherboardS/N(SerialNumber)stickeror

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•When connecting hardware components to the internal connectors on the motherboard, make

sure they are connected tightly and securely.

•When handling the motherboard, avoid touching any metal leads or connectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

componentssuchasamotherboard,CPUormemory.IfyoudonothaveanESDwriststrap,

keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Donotplacethecomputersystemonanunevensurface.

•Donotplacethecomputersysteminahigh-temperatureorwetenvironment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product,pleaseconsultacertiedcomputertechnician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its installation

and/or grounding instructions.

- 5 -

1-2 ProductSpecications

CPU AM4 Socket:

- AMDRyzen™ processor

- AMD7thGenerationA-series/Athlon™ processors

(Go to GIGABYTE's website for the latest CPU support list.)

Chipset AMD X370

Memory 4 x DDR4 DIMM sockets supporting up to 64 GB of system memory

Dual channel memory architecture

Support for DDR4 2667 (Note)/2400/2133 MHz memory modules

 Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in

non-ECCmode)

Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules

Support for Extreme Memory Prole (XMP) memory modules

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Onboard

Graphics

Integrated Graphics Processor:

 - 1xHDMIport,supportingamaximumresolutionof4096x2160@24Hz

* Support for HDMI 1.4 version.

- Maximum shared memory of 2 GB

Audio Realtek® ALC892 codec

High Denition Audio

2/4/5.1/7.1-channel

Support for S/PDIF Out

LAN Realtek® GbE LAN chip (10/100/1000 Mbit)

Expansion Slots 1 x PCI Express x16 slot, running at x16 (PCIEX16) (Note)

* For optimum performance, if only one PCI Express graphics card is to be installed,

be sure to install it in the PCIEX16 slot.

(The PCIEX16 slot conforms to PCI Express 3.0 standard.)

1 x PCI Express x16 slot, running at x4 (PCIEX4)

3 x PCI Express x1 slots

* The PCIEX4 slot shares bandwidth with the PCIEX1_2 and PCIEX1_3 slots. The

PCIEX4 slot operates at up to x2 mode when the PCIEX1_2/PCIEX1_3 slot is

populated. The PCIEX4 slot operates at up to x4 mode when both of the PCIEX1_2

and PCIEX1_3 slots are empty.

(The PCIEX4 and PCI Express x1 slots conform to PCI Express 2.0 standard.)

Multi-Graphics

Technology  Support for AMD Quad-GPU CrossFire™ and 2-Way AMD CrossFire™ technologies

Storage Interface  1 x M.2 connector (Socket 3, M key, type 2242/2260/2280/22110 SATA and PCIe

x4 (Note)/x2 SSD support)

8 x SATA 6Gb/s connectors

Support for RAID 0, RAID 1, and RAID 10

* Refer to "1-7 Internal Connectors," for the installation notices for the M.2 and SATA

connectors.

(Note) ActualsupportmayvarybyCPU.

- 6 -

USB ASMedia® USB 3.1 Gen 2 Controller:

- 2 x USB 3.1 Gen 2 Type-A ports (red) on the back panel

Chipset:

- 6 x USB 3.1 Gen 1 ports (2 ports on the back panel, 4 ports available

through the internal USB headers)

- 4 x USB 2.0/1.1 ports (available through the internal USB headers)

CPU:

- 4 x USB 3.1 Gen 1 ports on the back panel

Internal

Connectors

1 x 24-pin ATX main power connector

1 x 8-pin ATX 12V power connector

1 x CPU fan header

2 x system fan headers

1 x system fan/water cooling pump header

1 x M.2 Socket 3 connector

8 x SATA 6Gb/s connectors

1 x front panel header

1 x front panel audio header

1 x S/PDIF Out header

1 x serial port header

2 x USB 3.1 Gen 1 headers

2 x USB 2.0/1.1 headers

1 x Trusted Platform Module (TPM) header

1 x Clear CMOS jumper

Back Panel

Connectors

1 x PS/2 keyboard/mouse port

1 x HDMI port

6 x USB 3.1 Gen 1 ports

2 x USB 3.1 Gen 2 Type-A ports (red)

1 x RJ-45 port

 6 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Side Speaker

Out, Line In, Line Out, Mic In)

I/O Controller iTE® I/O Controller Chip

Hardware

Monitor

Voltage detection

Temperature detection

Fan speed detection

Overheating warning

Fan fail warning

Fan speed control

* Whether the fan (pump) speed control function is supported will depend on the fan

(pump) you install.

BIOS

2 x 128 Mbit ash

Use of licensed AMI UEFI BIOS

Support for DualBIOS ™

PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0

- 7 -

Unique Features Support for APP Center

* Available applications in APP Center may vary by motherboard model. Supported

functions of each application may also vary depending on motherboard specications.

- @BIOS

- 3DOSD

- AmbientLED

- AutoGreen

- BIOS Setup

- Cloud Station

- Color Tempertaure

- EasyTune

- Fast Boot

- Game Boost

- ON/OFF Charge

- Smart Backup

- Smart Keyboard

- Smart TimeLock

- System Information Viewer

- USB Blocker

- V-Tuner

Support for Q-Flash

Support for Xpress Install

Bundled

Software

Norton® Internet Security (OEM version)

cFosSpeed

Operating

System

Support for Windows 10 64-bit

Support for Windows 7 64-bit

* Please download the "Windows USB Installation Tool" from GIGABYTE's website

and install it before installing Windows 7.

Form Factor ATX Form Factor; 30.5cm x 23.0cm

* GIGABYTEreservestherighttomakeanychangestotheproductspecicationsandproduct-relatedinformationwithout

prior notice.

Please visit GIGABYTE's website

for support lists of CPU, memory

modules,SSDs,andM.2devices.

Please visit the Support\Utility List

page on GIGABYTE's website to

download the latest version of apps.

- 8 -

1-3 Installing the CPU

Installing the CPU

Locatethepinone(denotedbyasmalltriangle)oftheCPUsocketandtheCPU.

AM4 Socket

A Small Triangle Marking

DenotesPinOneofthe

Socket AM4 CPU

A Small Triangle Marking

DenotesCPUPinOne

1-4 Installing the Memory

DualChannelMemoryConguration

ThismotherboardprovidesfourmemorysocketsandsupportsDualChannelTechnology.Afterthememory

isinstalled,theBIOSwillautomaticallydetectthespecicationsandcapacityofthememory.EnablingDual

Channel memory mode will double the original memory bandwidth.

The four memory sockets are divided into two channels and each channel has two memory sockets as following:

ChannelA:DDR4_2,DDR4_4

ChannelB:DDR4_1,DDR4_3

Readthefollowingguidelinesbeforeyoubegintoinstallthememory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the

same capacity, brand, speed, and chips be used.

(GotoGIGABYTE'swebsiteforthelatestsupportedmemoryspeedsandmemorymodules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

ReadthefollowingguidelinesbeforeyoubegintoinstalltheCPU:

•Make sure that the motherboard supports the CPU.

(GotoGIGABYTE'swebsiteforthelatestCPUsupportlist.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locatethenotchesonbothsidesoftheCPUandalignmentkeysontheCPUsocket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•DonotturnonthecomputeriftheCPUcoolerisnotinstalled,otherwiseoverheatinganddamage

of the CPU may occur.

•SettheCPUhostfrequencyinaccordancewiththeCPUspecications.Itisnotrecommended

thatthesystembusfrequencybesetbeyondhardwarespecicationssinceitdoesnotmeetthe

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications,pleasedosoaccordingtoyourhardwarespecicationsincludingtheCPU,graphics

card, memory, hard drive, etc.

Please visit GIGABYTE's website for details on hardware installation.

- 9 -

1-5 Installing an Expansion Card

Readthefollowingguidelinesbeforeyoubegintoinstallanexpansioncard:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

1-6 Back Panel Connectors

PS/2 Keyboard/Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

USB 3.1 Gen 1 Port

TheUSB3.1Gen1portsupportstheUSB3.1Gen1specicationandiscompatibletotheUSB2.0

specication.UsethisportforUSBdevices.

HDMI Port

TheHDMIportisHDCPcompliantandsupportsDolbyTrueHDandDTSHD

MasterAudio formats. Italsosupportsupto 192 KHz/24bit 8-channelLPCM

audiooutput.YoucanusethisporttoconnectyourHDMI-supportedmonitor.Themaximumsupported

resolutionis4096x2160@24 Hz, butthe actual resolutions supportedare dependent on themonitor

being used.

AfterinstallingtheHDMIdevice,makesuretosetthedefaultsoundplaybackdevicetoHDMI.(The

itemnamemaydifferdependingonyouroperatingsystem.)

USB 3.1 Gen 2 Type-A Port (Red)

TheUSB3.1Gen2Type-AportsupportstheUSB3.1Gen2specicationandiscompatibletotheUSB

3.1Gen1andUSB2.0specication.UsethisportforUSBdevices.

DuetoCPUlimitations,readthefollowingguidelinesbeforeinstallingthememoryinDualChannelmode.

1. DualChannelmodecannotbeenabledifonlyonememorymoduleisinstalled.

2. WhenenablingDualChannelmodewithtwoorfourmemorymodules,itisrecommendedthatmemory

of the same capacity, brand, speed, and chips be used. For optimum performance, when enabling

DualChannelmodewithtwomemorymodules,werecommendthatyouinstallthemintheDDR4_1

andDDR4_2sockets.

DualChannelMemoryCongurationsTable:

DDR4_4 DDR4_2 DDR4_3 DDR4_1

2 Modules - - DS/SS - - DS/SS

DS/SS - - DS/SS - -

4 Modules DS/SS DS/SS DS/SS DS/SS

(SS=Single-Sided,DS=Double-Sided,"--"=NoMemory)

- 10 -

Please visit GIGABYTE's website for more software information.

•Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour

device and then remove it from the motherboard.

•Whenremovingthecable,pullitstraightoutfromtheconnector.Donotrockitsidetosidetoprevent

an electrical short inside the cable connector.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following

describesthestatesoftheLANportLEDs.

ActivityLED

Connection/

SpeedLED

LAN Port

ActivityLED:Connection/SpeedLED:

State Description

Orange 1 Gbps data rate

Green 100 Mbps data rate

Off 10 Mbps data rate

State Description

Blinking Datatransmissionorreceivingisoccurring

Off No data transmission or receiving is occurring

Center/Subwoofer Speaker Out (Orange)

Usethisaudiojacktoconnectcenter/subwooferspeakersina5.1/7.1-channelaudioconguration.

Rear Speaker Out (Black)

Thisjackcanbeusedtoconnectrearspeakersina4/5.1/7.1-channelaudioconguration.

Side Speaker Out (Gray)

Usethisaudiojacktoconnectsidespeakersina7.1-channelaudioconguration.

Line In (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out (Green)

The line out jack. Use this audio jack for a headphone or 2-channel speaker. This jack can be used to

connectfrontspeakersina4/5.1/7.1-channelaudioconguration.

Mic In (Pink)

The Mic in jack.

- 11 -

1-7 Internal Connectors

Readthefollowingguidelinesbeforeconnectingexternaldevices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

1) ATX_12V

2) ATX

3) CPU_FAN

4) SYS_FAN1/2

5) SYS_FAN3_PUMP

6) SATA3 0/1/2/3/4/5/6/7

7) M2F_32G

8) F_PANEL

9) SPDIF_O

10) F_AUDIO

11) COMA

12) F_USB30_1/F_USB30_2

13) F_USB1/F_USB2

14) TPM

15) BAT

16) CLR_CMOS

1210 511

- 12 -

DEBUG

PORT

G.QBOFM

131

2412

ATX

1/2) ATX_12V/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

onthemotherboard.Beforeconnectingthepowerconnector,rstmakesurethepowersupplyisturned

off and all devices are properly installed. The power connector possesses a foolproof design. Connect the

power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,

the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high

powerconsumptionbeused(500Worgreater).Ifapowersupplyisusedthatdoesnotprovidethe

required power, the result can lead to an unstable or unbootable system.

ATX:

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3GND 15 GND

4 +5V 16 PS_ON(softOn/Off)

5GND 17 GND

6 +5V 18 GND

7GND 19 GND

8 Power Good 20 NC

95VSB(standby+5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin

ATX)

23 +5V(Onlyfor2x12-pinATX)

12 3.3V (Only for 2x12-pin

ATX)

24 GND(Onlyfor2x12-pinATX)

ATX_12V:

Pin No. Denition Pin No. Denition

1GND(Onlyfor2x4-pin12V) 5+12V(Onlyfor2x4-pin12V)

2GND(Onlyfor2x4-pin12V) 6+12V(Onlyfor2x4-pin12V)

3GND 7 +12V

4GND 8 +12V

DEBUG

PORT

G.QBOFM

ATX_12V

- 13 -

3/4) CPU_FAN/SYS_FAN1/SYS_FAN2 (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire

isthegroundwire).ThemotherboardsupportsCPUfanspeedcontrol,whichrequirestheuseofaCPU

fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be

installed inside the chassis.

Pin No. Denition

1GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

5) SYS_FAN3_PUMP (System Fan/Water Cooling Pump Header)

The fan/pump header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a

foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation

(theblackconnectorwireisthegroundwire).Thespeedcontrolfunctionrequirestheuseofafanwith

fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed

inside the chassis. The header also provides speed control for a water cooling pump, refer to Chapter 2,

"BIOS Setup," "M.I.T.," for more information

Pin No. Denition

1GND

2 Voltage Speed Control

3 Sense

4 PWM Speed Control

DEBUG

PORT

G.QBOFM

•Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

•Thesefanheadersarenotcongurationjumperblocks.Donotplaceajumpercapontheheaders.

6) SATA3 0/1/2/3/4/5/6/7 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standard. Each SATA connector supports a single SATA device. The SATA connectors support

RAID0,RAID1,andRAID10.RefertoChapter3,"ConguringaRAIDSet,"forinstructionsonconguring

aRAIDarray.

Pin No. Denition

1GND

2 TXP

3 TXN

4GND

5RXN

6RXP

7GND

SATA3 0 2 4 6

1 3 5 7

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

SYS_FAN1

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

CPU_FAN SYS_FAN2

DEBUG

PORT

G.QBOFM

- 14 -

7) M2F_32G (M.2 Socket 3 Connector)

 TheM.2connectorsupportsM.2SATASSDsandM.2PCIeSSDsandsupportsSATARAIDconguration

throughtheAMDChipset.PleasenotethatanM.2PCIeSSDcannotbeusedtocreateaRAIDarray. Refer

toChapter3,"ConguringaRAIDSet,"forinstructionsonconguringaRAIDarray.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3 4 5

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_

USB0_B

B_ F_USB3



80110 60 42

SelecttheproperholefortheM.2SSDtobeinstalledandrefastenthescrewandnut.

FollowthestepsbelowtocorrectlyinstallanM.2SSDintheM.2connector.

Step 1:

Use a screw driver to unfasten the screw and nut from the motherboard. Locate the proper mounting hole

fortheM.2SSDtobeinstalledandthenscrewthenutrst.

Step 2:

SlidetheM.2SSDintotheconnectoratanangle.

Step 3:

PresstheM.2SSDdownandthensecureitwiththescrew.

SATA3 0 SATA3 1 SATA3 2 SATA3 3 SATA3 4 SATA3 5 SATA3 6 SATA3 7

M.2SATASSD aaaaaaar

M.2PCIex4SSD*

aaaaaaaa

M.2PCIex2SSD

aaaaaaaa

NoM.2SSDInstalled aaaaaaaa

a: Available, r: Not available

* ForAMDRyzen™ processor only.

Connector

Type of

M.2SSD

Installation Notices for the M2F_32G and SATA Connectors:

DuetothelimitednumberoflanesprovidedbytheChipset,theavailabilityoftheSATAconnectorsmaybe

affected by the type of devices installed in the M2F_32G connector. The M2F_32G connector shares bandwidth

withtheSATA37connector.Refertothefollowingtablefordetails.

- 15 -

9) SPDIF_O (S/PDIF Out Header)

 ThisheadersupportsdigitalS/PDIFOutandconnectsaS/PDIFdigitalaudiocable(providedbyexpansion

cards)fordigitalaudiooutputfromyourmotherboardtocertainexpansioncardslikegraphicscardsand

soundcards.Forexample,somegraphicscardsmayrequireyoutouseaS/PDIFdigitalaudiocablefor

digitalaudiooutputfromyourmotherboardtoyourgraphicscardifyouwishtoconnectanHDMIdisplay

tothegraphicscardandhavedigitalaudiooutputfromtheHDMIdisplayatthesametime.Forinformation

aboutconnectingtheS/PDIFdigitalaudiocable,carefullyreadthemanualforyourexpansioncard.

Pin No. Denition

1SPDIFO

2GND

8) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator

on the chassis to this header according to the pin assignments below. Note the positive and negative pins

before connecting the cables.

System Status LED

S0 On

S3/S4/S5 Off

•PW(PowerSwitch,Red):

Connects to the power switch on the chassis front panel. You may

congurethewaytoturnoffyoursystemusingthepowerswitch(refer

toChapter2,"BIOSSetup,""Power,"formoreinformation).

•SPEAK (Speaker,Orange):

Connects to the speaker on the chassis front panel. The system reports

system startup status by issuing a beep code. One single short beep

will be heard if no problem is detected at system startup.

•PLED/PWR_LED (PowerLED,Yellow/Purple):

Connects to the power status indicator

onthechassisfrontpanel.TheLEDison

whenthesystemisoperating.TheLEDis

off when the system is in S3/S4 sleep state

orpoweredoff(S5).

•HD (HardDriveActivityLED,Blue):

 ConnectstotheharddriveactivityLEDonthechassisfrontpanel.TheLEDisonwhentheharddriveis

reading or writing data.

•RES (ResetSwitch,Green):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the

computerfreezesandfailstoperformanormalrestart.

•CI (ChassisIntrusionHeader,Gray):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been

removed. This function requires a chassis with a chassis intrusion switch/sensor.

•NC (Orange):NoConnection.

PowerLED

DEBUG

PORT

G.QBOFM

CI-

CI+

PWR_LED-

PWR_LED+

PLED-

PW-

SPEAK+

SPEAK-

PLED+

PW+

PowerLED

HD-

RES+

HD+

RES-

HardDrive

ActivityLED

Reset

Switch Chassis Intrusion

Header

Power Switch Speaker

PWR_LED-

The front panel design may differ by chassis. A front panel module mainly consists of power switch,

resetswitch,powerLED,harddriveactivityLED,speakerandetc.Whenconnectingyourchassis

front panel module to this header, make sure the wire assignments and the pin assignments are

matched correctly.

- 16 -

Pin No. Denition Pin No. Denition

1 VBUS 11 D2+

2SSRX1- 12 D2-

3SSRX1+ 13 GND

4GND 14 SSTX2+

5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 GND

7GND 17 SSRX2+

8D1- 18 SSRX2-

9D1+ 19 VBUS

10 NC 20 No Pin

12) F_USB30_1/F_USB30_2 (USB 3.1 Gen 1 Headers)

 TheheadersconformtoUSB3.1Gen1andUSB2.0specicationandcanprovidetwoUSBports.For

purchasing the optional 3.5" front panel that provides two USB 3.1 Gen 1 ports, please contact the local

dealer.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3 4 5

 S3 BSSS U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

10) F_AUDIO (Front Panel Audio Header)

 ThefrontpanelaudioheadersupportsHighDenitionaudio(HD)andAC'97audio.Youmayconnectyour

chassis front panel audio module to this header. Make sure the wire assignments of the module connector

match the pin assignments of the motherboard header. Incorrect connection between the module connector

and the motherboard header will make the device unable to work or even damage it.

ForHDFrontPanelAudio: For AC'97 Front Panel Audio:

•ThefrontpanelaudioheadersupportsHDaudiobydefault.

•Audio signals will be present on both of the front and back panel audio connections simultaneously.

•Some chassis provide a front panel audio module that has separated connectors on each wire

instead of a single plug. For information about connecting the front panel audio module that has

different wire assignments, please contact the chassis manufacturer.

Pin No. Denition

1 MIC2_L

2GND

3MIC2_R

4 NC

5LINE2_R

6 Sense

7FAUDIO_JD

8 No Pin

9 LINE2_L

10 Sense

Pin No. Denition

1 MIC

2GND

3 MIC Power

4 NC

5LineOut(R)

6 NC

7 NC

8 No Pin

9LineOut(L)

10 NC

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3 4 5

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_

USB0_B

B_ F_USB3



9 1

10 2

11) COMA (Serial Port Header)

The COM header can provide one serial port via an optional COM port cable. For purchasing the optional

COM port cable, please contact the local dealer.

Pin No. Denition Pin No. Denition

1NDCD- 6NDSR-

2 NSIN 7 NRTS-

3 NSOUT 8 NCTS-

4NDTR- 9NRI-

5GND 10 No Pin

- 17 -

14) TPM (Trusted Platform Module Header)

 YoumayconnectaTPM(TrustedPlatformModule)tothisheader.

Pin No. Denition Pin No. Denition

1 LCLK 11 LAD0

2GND 12 GND

3LFRAME 13 NC

4 No Pin 14 NC

5LRESET 15 SB3V

6 NC 16 SERIRQ

7LAD3 17 GND

8LAD2 18 NC

9 VCC3 19 NC

10 LAD1 20 NC

15) BAT (Battery)

 Thebatteryprovidespowertokeepthevalues(suchasBIOScongurations,date,andtimeinformation)

intheCMOSwhenthecomputeristurnedoff.Replacethebatterywhenthebatteryvoltagedropstoalow

level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.

2. Gently remove the battery from the battery holder and wait for one minute. (Or

use a metal object like a screwdriver to touch the positive and negative terminals

ofthebatteryholder,makingthemshortfor5seconds.)

3. Replacethebattery.

4. Plug in the power cord and restart your computer.

•Always turn off your computer and unplug the power cord before replacing the battery.

•Replacethebatterywithanequivalentone.Dangerofexplosionifthebatteryisreplacedwith

an incorrect model.

•Contact the place of purchase or local dealer if you are not able to replace the battery by yourself

or uncertain about the battery model.

•Wheninstallingthebattery,notetheorientationofthepositiveside(+)andthenegativeside(-)

ofthebattery(thepositivesideshouldfaceup).

•Used batteries must be handled in accordance with local environmental regulations.

13) F_USB1/F_USB2 (USB 2.0/1.1 Headers)

 TheheadersconformtoUSB2.0/1.1specication.EachUSBheadercanprovidetwoUSBportsviaan

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Denition Pin No. Denition

1Power(5V) 6USBDY+

2Power(5V) 7GND

3USBDX- 8GND

4USBDY- 9 No Pin

5USBDX+ 10 NC

•DonotplugtheIEEE1394bracket(2x5-pin)cableintotheUSB2.0/1.1header.

•Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord

from the power outlet to prevent damage to the USB bracket.

DEBUG

PORT

G.QBOFM

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3 4 5

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

- 18 -

16) CLR_CMOS (Clear CMOS Jumper)

 UsethisjumpertocleartheBIOScongurationandresettheCMOSvaluestofactorydefaults.Toclear

the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

•Always turn off your computer and unplug the power cord from the power outlet before clearing

the CMOS values.

•Aftersystemrestart,gotoBIOSSetuptoloadfactorydefaults(selectLoadOptimizedDefaults)or

manuallyconguretheBIOSsettings(refertoChapter2,"BIOSSetup,"forBIOScongurations).

Open: Normal

Short: Clear CMOS Values

- 19 -

Chapter 2 BIOS Setup

BIOS(Basic Input and Output System) records hardware parameters of the systemin the CMOS on the

motherboard.ItsmajorfunctionsincludeconductingthePower-OnSelf-Test(POST)duringsystemstartup,

saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows

theusertomodifybasicsystemcongurationsettingsortoactivatecertainsystemfeatures.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to

keepthecongurationvaluesintheCMOS.

ToaccesstheBIOSSetupprogram,pressthe<Delete>keyduringthePOSTwhenthepoweristurnedon.

ToupgradetheBIOS,useeithertheGIGABYTEQ-Flashor@BIOSutility.

•Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.

•@BIOSisaWindows-basedutilitythatsearchesanddownloadsthelatestversionofBIOSfromtheInternet

and updates the BIOS.

•BecauseBIOSashingispotentiallyrisky,ifyoudonotencounterproblemsusingthecurrentversionofBIOS,

itisrecommendedthatyounotashtheBIOS.ToashtheBIOS,doitwithcaution.InadequateBIOSashing

may result in system malfunction.

•Itisrecommendedthatyounotalterthedefaultsettings(unlessyouneedto)topreventsysteminstabilityorother

unexpected results. Inadequately altering the settings may result in system's failure to boot. If this occurs, try to

cleartheCMOSvaluesandresettheboardtodefaultvalues.(Refertothe"LoadOptimizedDefaults"sectionin

thischapterorintroductionsofthebattery/clearCMOSjumperinChapter1forhowtocleartheCMOSvalues.)

2-1 Startup Screen

The following startup Logo screen will appear when the computer boots.

(SampleBIOSVersion:F1a)

Function Keys

•When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.

•The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

TherearetwodifferentBIOSmodesasfollowsandyoucanusethe<F2>keytoswitchbetweenthetwomodes.

The Classic Setup mode provides detailed BIOS settings. You can press the arrow keys on your keyboard to move

amongtheitemsandpress<Enter>toacceptorenterasub-menu.Oryoucanuseyourmousetoselectthe

item you want. Easy Mode allows users to quickly view their current system information or to make adjustments

foroptimumperformance.InEasyMode,youcanuseyourmousetomovethroughcongurationitems.

- 20 -

Page is loading ...

Gigabyte GA-AX370-Gaming Owner's manual

Gigabyte GA-AX370-Gaming Owner's manual

Gigabyte GA-AX370-Gaming Owner's manual

Related papers