Wireless Smart-Pen technology by Lithuanian Irons
USER MANUAL
IMPORTANT SAFETY INFORMATION………………………
MACHINE OVERVIEW…………………………………………
THE GRIP AND NEEDLE DEPTH ADJUSTMENT………….
EXCHANGEABLE BATTERIES……………………………….
THE BATTERY REPLACEMENT……………………………..
BASIC MACHINE CONTROL…………………………………
SCREEN OVERVIEW…………………………………………..
MEMORY PRESETS……………………………………………
DIGITAL SOFTNESS……………………………………………
DIGITAL SOFTNESS CONTROL………………………………
MAIN MENU……………………………………………………..
MAIN MENU PARAMETERS…………………………………..
TIMER MENU…………………………………………………….
SCREEN COLOR AND STYLE…………………………………
DIFFERENT SCREEN STYLES………………………………..
2nd MENU PAGE………………………………………………..
TECHNICAL SPECIFICATIONS………………………….…….
WARNING SIGNS……………………………………………….
SAFETY, CLEANING AND HYGIENE…………………………
SERVICE AND MAINTENANCE………………………….……
WARRANTY……………………………………………….……..
CONTENTS:
3
4
5
6
7
8
9
10
10
11
12
13
14
15
16
17
18
19
20
20
21
IMPORTANT SAFETY INFORMATION
- 3 -
•The device may not be used by persons (including children) with reduced physical, sensory or mental capabilities or lack of
experience or knowledge.
•If the device is not being used for a longer period of time, remove the battery.
•Carefully read this entire operating manual.
•Follow the safety regulations applicable to tattooing in your country.
•Only use needle cartridges with internal safety membrane.
•Any failure to observe the safety information and instructions may result in electric shock, a fire and/or cause serious injuries.
•Take the battery out of the machine before transporting or storing it. If the machine is unintentionally activated, there is a risk of
injury.
•Protect the battery from heat (such as from continuous sun exposure), fire and immersion into water. Do not store or operate the
battery near hot or flammable objects. There is a risk of explosion.
•Always place the batteries in the battery sections of Your machine package when not in use in order to protect them from external
influences.
•When not in use, keep the battery away from paper clips, coins, keys, nails, screws or any other small metal objects that cause the
contacts to be bridged.
•A short circuit between the battery contacts may cause burns or result in a fire.
•Only use the original charger to charge the battery. The risk of fire cannot be excluded if you do not use an original charger.
•Only use the battery in connection with original Cyber tattoo machines.
•Only use the supplied battery type NCR18500A. Any other batteries may cause severe injuries and a risk of fire.
•We will accept no liability and warranty if other batteries are used.
•Keep the battery away from children.
•Check the battery for damage.
•Do not charge a damaged battery or use it.
•Charge the battery fully prior to use.
•Do not place the charger and the battery near flammable materials. Only charge the battery in dry state and at a fireproof location.
There is a risk of fire due to the heat that builds up while charging.
•Fluid may leak from the battery if it is improperly used. Avoid contact with it. Rinse with water if you accidentally come in contact with
it. If the liquid gets into your eyes, also seek out your physician for additional help.
•Leaking battery fluid may cause skin irritations or burns.
•Batteries must not be exposed to mechanical impacts. There is a risk of damaging the battery.
•If damaged, or if the battery is improperly used, vapors may escape from the battery. Introduce fresh air and seek out a physician if
you have any physical symptoms. Vapors may irritate the respiratory system.
MACHINE OVERVIEW
Battery cap
Machine body: Custom
Brushless Faulhaber
Motor with 2 ball bearings
Machine grip
Cartridge needle
input
Color display
Control buttons
THE CYBER
Smart wireless Pen-Style tattoo machine for
use with needle cartridges. It features a
maintenance-free mechanism which offers
solid hit with minimum vibration and low
noise.
Package includes: CYBER machine, 2pcs.
of rechargeable Panasonic Li-ion batteries
(model 18500) and USB battery charger.
Machine frame parts are made from solid
rods of high grade aluminium, then
anodised.
The CYBER has a built-in color display to
show information and make it easier for the
user to control the device. Users can fully
configure this pen to their preference by
using features such as digital hit softness,
customisable voltage and softness memory
presets, changeable screen color and style,
screen brightness, sleep mode and button
sound control.
- 4 -
THE GRIP AND NEEDLE DEPTH ADJUSTMENT
Hold the machine body
while rotating the grip
- 5 -
The CYBER comes equipped as standard with 33mm grip.
The Grip is safe to be sterilised in an autoclave at temperatures not higher than 135° Celsius
or also suitable to be sprayed with cold sterilisation products.
To adjust needle depth, hold the machine body and simply rotate the grip clockwise or counter
clockwise.
Rotate the grip to remove it
or adjust needle depth
Friction O-Ring
Plastic click ring
Attention: If the Grip rotates too hard, add a bit of PTFE or other silicone grease on the friction
O-Ring and plastic click ring.
EXCHANGEABLE BATTERIES
- 6 -
Contact pin
Battery cap
2 x Batteries
The CYBER machine is designed for use with standard
rechargeable Panasonic Li-ion batteries (model 18500).
That allows easy to service or replace the battery if it
became worse. And also safe to store the machine on a
flight or any other extreme transportation (the battery has to
be removed and stored separately).
Attention: Always check and keep the battery
contacts, battery cap contact plate and machine
contact pin clean. Any dust, grease or vaseline will
worsen the contact and disrupt the smooth operation
of the machine or even damage the machine.
It is recommended to fully charge the batteries before their
first use for 2 - 3 hours.
THE BATTERY REPLACEMENT
- 7 -
Battery cap
1. Unscrew the battery cap. 2. Insert a charged battery “+” down.
+
-
3. Screw the battery cap back on to the rear end of the machine.
BASIC MACHINE CONTROL
- 8 -
To turn ON/OFF the machine, press and hold
the “Power button” for 3 seconds.
Power button
Step down
button
Step up
button
To increase the voltage / machine speed, press or hold
the “Step up button”. Single press increases the voltage
by 0,1 volts.
To decrease the voltage / machine speed, press or hold
the “Step down button”. Single press decreases the voltage
by 0,1 volts.
To turn ON/OFF the machine motor, single press the “Power button”.
Attention: We do not recommend turning on and run the motor with no
needle cartridge attached to the machine. The CYBER uses a slider
system mechanism without springs, so cartridge needle membrane works
as a back spring here and ensures stable, smooth and silent operation.
SCREEN OVERVIEW
- 9 -
Battery level
Voltage
(5.0V - 9.5V)
The machine
motor is turned on
Chosen memory
preset, 1 of 4
(A,B,C,D)
Active or
Total timer
Digital softness preset,
where ‘0’ is no softness
and ‘9’ is max. softness
VOLTAGE CONTROL
SCREEN
MEMORY PRESETS
- 10 -
Memory preset
(A,B,C,D)
The Cyber has a feature to automatically save user’s voltage
and digital softness as 1 of 4 presets: A , B , C or D.
Users can configure every preset to their preference.
To configure the preset, simply change the voltage and/or digital softness
and all changes will be automatically saved to the selected preset.
Press + buttons to switch between memory presets.
DIGITAL SOFTNESS
This is a feature that allows to control the machine motor power response
to the skin’s resistance and make it softer if needed. By choosing
between 10 levels user can adjust the sensitivity and softness. Special
software automatically calculates cartridge membrane hardness and
adjusts the softness parameter to the best value in selected mode.
“0” is a default motor work without additional softness and “9” is the
softest mode.
Digital softness
(0-9)
Attention: Do not remove or change needle cartridges while the machine is
running in digital softness mode. Different cartridges have different membranes.
Stop the machine motor, change the cartridge and turn on the motor again. That
way machine software will correctly recalculate cartridge membrane hardness.
- 11 -
DIGITAL SOFTNESS CONTROL
User can only control the Digital Softness while machine motor is running.
Digital Softness
bar
1. Press button to turn on the machine motor.
2. Press and hold the same button for 2 seconds to enter to Digital Softness control menu.
3. The following screen will
appear
4. Control the softness
using , buttons.
To come back to the voltage control screen, press and hold button for 2 seconds or leave the Digital
Softness screen and it will automatically switch back to the Voltage Control screen in 12 seconds.
- 12 -
MAIN MENU
Users can fully configure the machine to their preference in Main Menu.
1. Press + buttons to enter the Main Menu.
2. The following screen will appear:
3. Switch between parameters
using , buttons.
4. To enter or change the
parameter press button.
6. To exit the Main Menu press and hold
any of 3 buttons for 2 seconds.
1st page
2nd page
5. Scroll down to enter the 2nd page
- 13 -
MAIN MENU PARAMETERS
1st page
2nd page
1. Timer Menu
2. Screen color
style
3. Screen style
4. Screen brightness
5. Button sound
6. Sleep mode
- 14 -
TIMER MENU
1st page
Total timer, starts
automatically when user
turns on the machine.
Run timer, counts the
machine motor run time.
Turn OFF the timer.
1. Press button to enter the Timer Menu.
2. Select which timer to use on the main screen.
3. Press button to confirm selection.
Timer Menu
- 15 -
SCREEN COLOR AND STYLE
Press button to switch between 14 different screen color styles.
SCREEN COLOR
SCREEN STYLE
Press button to switch between 7 different screen styles.
- 16 -
DIFFERENT SCREEN STYLES
Voltage Control
screen
Voltage Control
screen
Digital
Softness
Digital
Softness
Voltage Control
screen
Digital
Softness
- 17 -
2nd MENU PAGE
Press button to change screen brightness.
Press button to change button sound.
Press button to change sleep mode.
3 modes: louder, quieter and no sound.
3 modes: short, medium and long.
Short: Screen dimming after 30 seconds, full shutdown after 20min.
Medium: Screen dimming after 1 min., full shutdown after 40min.
Long: Screen dimming after 1 min 30 sec., full shutdown after 60min.
Controls screen dimming when user does not press any button and full machine
shutdown, when the machine is not in use.
- 18 -
TECHNICAL SPECIFICATIONS
Dimension, D x L
33mm x 125mm
Weight (with battery)
190g (with battery)
Operating voltage
5.0 - 9.5 Volts
Needle stitches/second
55-135
Needle stroke length
4.0mm
Needle depth adjustment
4.0mm
Power intake
3W
Needle type
Cartridge needles
Drive
Brushless DC motor
Operating mode
Continuous operation
Battery designation
NCR18500A
Rated battery voltage
3.7 V
Battery type
Lithium-ion
Battery dimensions DxL
18.15mm x 49.36mm
Rated capacity value
1900 mAh
Charging method
CC-CV
Charging voltage
4.2 V
Battery weight
33.5g max.
Energy density
536 Wh/l, 204 Wh/kg
Charger input voltage
DC 5.0V 2.1A
Charger constant current
0.5A x 2 / 1A x 2
Charger Cut-Off Voltage
4.2 ± 0.05V
Charger Cut-Off Current
< 120mA
Operating Temperature
+10°C to +35°C
+50°F to +95°F
- 19 -
WARNING SIGNS
WARNING SIGN
DATA RESET
when factory reset is done
or parameters changed.
LOW BATTERY
Replace the battery with a
charged one.
TOO HIGH BATTERY
VOLTAGE
Wrong or bad battery,
replace the battery.
OVERLOAD
The motor is overloaded or
damaged.
SHORT CIRCUIT
Short circuit in the
electronics or motor.
The CYBER has smart testing software, that checks the machine and informs about
one of the following problems. This software stops or does not allow to start the motor
if one of these problems appear for the user and machine safety reasons.
- 20 -
SERVICE AND MAINTENANCE
The CYBER comes pre-lubricated from factory and does not require additional lubrication.
Do not use any type of oil for lubrication.
Any changes or modifications not approved by the manufacturer could void the warranty.
We strongly recommend contacting us to service Your device every 12 months to ensure
the proper condition of all working parts, internal clean up and fresh lubrication.
Service is subject to fees.
For service and maintenance inquiries, please contact: [email protected]
SAFETY, CLEANING AND HYGIENE
Although the grip is autoclavable we strongly recommend using plastic bags or barriers to
cover the machine and keep it clean. Never spray or pour fluids directly on the surface to
prevent fluids from entering the machine, it can cause short circuit or damage internal
system elements and will void the warranty.
Use only slightly damped piece of paper or wipes to apply disinfection/sterilisation products.
Always use cartridges with internal membrane. This will allow avoiding contamination inside
the machine. Any fluids, pigments or oil inside the machine will void the warranty and may
require additional service or replacement of internal parts.
Page is loading ...
/
