PARADOX Esprit 748ES Programming Manual

PARADOX
Brand
PARADOX
Model
Esprit 748ES
Category
Touch screen monitors
Type
Programming Manual
48ESEP-02
SOFTWARE VERSION 3.10
CONTROL PANEL RESET:
Installer lock must be unlocked.
(Address 058: enter any value other than 147)
Power down reset
(1) Remove battery and AC to power down the unit.
(2) Connect a jumper between "reset jumper" pins.
(3) Connect AC then the battery.
(4) Wait 10 seconds.
(5) Remove jumper.
Factory default installer and master codes will be reinstated. Values entered at addresses 008-043, 062-126 and 300-527
as well as all user codes, will be erased ([2ND] [2ND]). Programmed values of all other addresses do not change.
HEXA PROGRAMMING:
All digits from 0 to F are valid. Values are programmed into
memory locations from address 000 to 043 and from address
300 to 527.
1) Press [ENTER]+ installer code.
2) [
ENTER
]
will flash (programming mode).
3) Enter 3 digit memory address.
4) Current value will be displayed on keypad.
5) Enter 2 digit data.
6) Go to step 3 for next address.
To exit programming mode, press [CLEAR].
STREAMLINED SECTION PROGRAMMING
Can be used to program sections 00 to 67. (addresses 000 to 043 and 300 to 527)
Press [ENTER], installer code, and [7]. ([2ND]and [ENTER]keys alternately flash.)
Enter a 2-digit section number, followed by 8 digits to program that section (confirmation beep). Data will be saved auto-
matically and the software advances to the next programming section. To exit programming mode press [CLEAR].
INSTALLER CODE: (reset code 747474)(addresses 000, 001, 002) SECTION 00
Full access to programming, except access codes.
(addresses 127-299) No access to arming/disarming. Can be used to
modify installer code. Use only numeric keys from [1] to [10]. (key [10] = 0)
PANEL ANSWER OPTIONS: (address 003) SECTION 00
First digit disables “Answering Machine Override” (key [2ND]or key [1]), or determines period of time between first and
second call (see table below). Second digit determines number of rings required before panel will answer. If [2ND][2ND]is
entered, panel will not answer. (Default value is [2ND] [8].)
- 1 -
Value of
2ND digit = 10
( 8+ 2= 10)
Value of
1ST digit = 3
( 2+ 1= 3)
VALUE = "3A"
HEXA DISPLAY
No display = SKIP (empty) No light = 0
10 = [0] = [A]
If key is lit =8 =4 =2 =1
If key is lit =8 =4 =2 =1
TELEPHONE AND ACCOUNT NUMBERS: (reset empty)
If only one central station phone number is used, program the same number for telephone number 1 and 2.
[10] = the number "0" [BYP]= switch from pulse to tone while dialing
[11] = *[MEM]= pause 4 seconds
[12] = # [TRBL]= end of number
COMPUTER TELEPHONE NUMBER: (View at addresses 008 to 015.)
02__ / __ / __ / __ / __ / __ / __ / __ 03__ / __ / __ / __ / __ / __ / __ / __
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CENTRAL STATION TELEPHONE NUMBER 1: (View at addresses 016 to 023.)
04 __ / __ / __ / __ / __ / __ / __ / __ 05 __ / __ / __ / __ / __ / __ / __ / __
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CENTRAL STATION TELEPHONE NUMBER 2: (View at addresses 024 to 031.)
06 __ / __ / __ / __ / __ / __ / __ / __ 07 __ / __ / __ / __ / __ / __ / __ / __
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
ACCOUNT "A" AND "B": (View at addresses 032 to 035.)
08 ___ / ___ / ___ / ___ ___ / ___ / ___ / ___
1 2 3 4 5 6 7 8
A B
If only one account number is required, the same number must be entered for both account "A" and "B".
- 2 -
PG748ES
Press [
TRBL
] to end phone
number if less than 16
dig
its are programmed.
Press [
TRBL
] to end phone
number if less than 16
dig
its are programmed.
For 3 digit account num-
bers, enter "skip" ([2ND])
as first digit.
Press [
TRBL
] to end phone
number if less than 16
dig
its are programmed.
Streamline
section Streamline
section
Streamline
section Streamline
section
Streamline
section Streamline
section
Streamline
section
[2 ]ND
[2 ]ND [2 ]ND
Streamline
section Data Description Address
___/___
___/___
/
___/___
___ ___
Future use
1st digit: value must be entered i.e.
2nd digit: time correction (See table)
1st digit: telephone 1 format
2nd digit: telephone 2 format
1st digit: PGM 1 type
2nd digit: PGM 2 type
[2 ]ND 036
037
038
039
09
PGM 1
PGM 2
PGM mask 1
PGM mask 2
040
041
042
043
___/___
___/___
/
___/___
___ ___
10
TIME CORRECTION:
(address second digit)037
[2 ]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
ND - No adjustment
- Plus 4 sec.
- Plus 8 sec.
- Plus 12 sec.
- Plus 16 sec.
- Plus 20 sec.
- Plus 24 sec.
- Plus 28 sec.
[8]
[9]
[10]
[11]
[12]
[]
[]
[]
- Minus 4 sec.
- Minus 8 sec.
- Minus 12 sec.
- Minus 16 sec.
- Minus 20 sec.
- Minus 24 sec.
- Minus 28 sec.
- Minus 32 sec.
BYP
MEM
TRBL
COMMUNICATOR FORMATS
Key
[2 ]
[1]
[2]
[3]
[4]
[5]
ND [6]
[7]
[8]
[9]
[10]
[]
TRBL
= slow (1400Hz, 1900Hz, 10bps)
= (1400Hz, 1800Hz, 10bps)
= fast (1400Hz, 1900Hz, 20bps)
= (2300Hz, 1800Hz, 20bps)
= (40bps with 1400Hz handshake)
= (40bps with 2300Hz handshake)
ADEMCO
SILENT KNIGHT
SESCOA
RADIONICS
RADIONICS
= with PARITY (1400Hz, 40bps)
= with PARITY (2300Hz, 40bps)
= express
= contact ID (programmable codes)
= contact ID (all codes)
= - no handshake (personal dialing)
RADIONICS
RADIONICS
ADEMCO
ADEMCO
ADEMCO
DTMF
- 3 -
PG748ES
For addresses to , see pages 7 to 10.044 126
CID
100:
110:
111:
112:
113
114:
115:
116:
117:
118:
120:
121:
122:
123:
130:
131:
132:
133:
136:
137:
138:
140:
150:
151:
152:
153:
154:
155:
156:
157:
158:
159:
161:
CID
300:
301:
302
305:
306:
309:
320:
321:
323:
350:
351:
354:
370:
371:
372:
373:
382:
383:
400:
401:
402:
403:
404:
407:
410:
441:
570:
572:
573:
574:
601:
602:
625:
PROG. VALUE
[2 ] / [1]
[2 ] / [2]
[2 ] / [3]
[2 ] / [4]
[2 ] / [5]
[2 ] / [6]
[2 ] / [7]
[2 ] / [8]
[2 ] / [9]
[2 ] / [10]
[2 ] / [11]
[2 ] / [12]
[2 ] / [ ]
[2 ] / [ ]
[2 ] / [ ]
[1] / [2 ]
[1] / [1]
[1] / [2]
[1] / [3]
[1] / [4]
[1] / [5]
[1] / [6]
[1] / [7]
[1] / [8]
[1] / [9]
[1] / [10]
[1] / [11]
[1] / [12]
[1] / [ ]
[1] / [ ]
[1] / [ ]
[2] / [2 ]
[2] / [1]
ND
ND
ND
ND
ND
ND
ND
ND
ND
ND
ND
ND
ND BYP
ND MEM
ND TRBL
ND
BYP
MEM
TRBL
ND
PROG. VALUE
[2] / [2]
[2] / [3]
[2] / [4]
[2] / [5]
[2] / [6]
[2] / [7]
[2] / [8]
[2] / [9]
[2] / [10]
[2] / [11]
[2] / [12]
[2] [ ]
[2] [ ]
[2] [ ]
[3] / [2 ]
[3] / [1]
[3] / [2]
[3] / [3]
[3] / [4]
[3] / [5]
[3] / [6]
[3] / [7]
[3] / [8]
[3] / [9]
[3] / [10]
[3] / [11]
[3] / [12]
[3] [ ]
[3] [ ]
[3] [ ]
[4] / [2 ]
[4] / [1]
[4] / [2]
/
/
/
/
/
/
BYP
MEM
TRBL
ND
BYP
MEM
TRBL
ND
REPORTING CODE
AUXILIARY ALARM
FIRE ALARM
FIRE SMOKE
COMBUSTION
WATER FLOW
HEAT
PULLSTATION
DUCT
FLAME
NEAR ALARM
PANIC ALARM
DURESS
SILENT PANIC
AUDIBLE PANIC
BURGLARY
PERIMETER BURG.
INTERIOR BURG.
24HR BURGLARY
BURGLARY OUTDOOR
BURGLARY TAMPER
BURGLARY NEAR ALARM
GENERAL ALARM
24 HOUR AUX
GAS DETECTED
REFRIGERATION
LOSS OF HEAT
WATER LEAKAGE
FOIL BREAK ALARM
DAY TROUBLE ALARM
LOW GAS LEVEL
HIGH TEMPERATURE
LOW TEMPERATURE
LOSS AIR FLOW
REPORTING CODE
SYSTEM TROUBLE
AC LOSS
LOW SYSTEM BATTERY
SYSTEM RESET
PROGRAM CHANGED
BATTERY TEST FAIL
SOUNDER/RELAY TROUBLE
BELL 1 TROUBLE
ALARM RELAY TROUBLE
COMMUNICATION TROUBLE
TELCO 1 FAULT
FAIL TO COMMUNICATE
PROTECTION LOOP TROUBLE
PROTECTION LOOP OPEN
PROTECTION LOOP SHORT
FIRE LOOP TROUBLE
SENSOR TROUBLE
SENSOR TAMPER
OPEN/CLOSE
OPEN/CLOSE BY USER #
GROUP OPEN/CLOSE
AUTOMATIC OPENING/CLOSING
LATE TO OPEN/CLOSE
REMOTE ARM DOWNLOAD
REMOTE ACCESS
OPEN/CLOSE - STAY MODE
BYPASS
24 HOUR ZONE BYPASS
BURGLARY BYPASS #
GROUP BYPASS
MANUAL TEST
PERIODIC TEST
TIME/DATE RESET
PROGRAMMABLE CONTACT ID EVENT CODES
All addresses from to (sections to ) programmed with values other than will report the contact
ID codes corresponding to the values programmed. Values to be programmed should be selected from this table.
300 527 11 67 [2 ] [2 ]ND ND
- 4 -
REPORTING CODES: (reset code = “empty" )
All digits from to are valid. Enter (skip) = digit will not be reported except for contact I.D. programmable codes.
For single digit reporting enter "skip" ( ) as first digit.
(Select Contact I.D (all codes) - key for both central station numbers at section - address .)
[2 ] [2 ]
[1] [F] [2 ]
[2 ]
[10] 09 038
ND ND
ND
ND
If CONTACT I.D. format (all codes) is selected, addresses 300 to 527 (sections 11 to 67) do not have to be programmed.
PG748ES
___/___
___/___
/
___/___
___ ___
Auto / Espload
Master
User code 1
User code 2
300
301
302
303
Streamline
section Streamline
section
Data Data
Description Description
Address Address
ARMING CODES:(closing)
___/___
___/___
/_
___/___
___ __
User code 23
User code 24
User code 25
User code 26
324
325
326
327
17
11
___/___
___/___
/
___/___
___ ___
User code 3
User code 4
User code 5
User code 6
304
305
306
307
___/___
___/___
/_
___/___
___ __
User code 27
User code 28
User code 29
User code 30
328
329
330
331
12
18
User code 7
User code 8
User code 9
User code 10
User code 15
User code 16
User code 17
User code 18
308
309
310
311
316
317
318
319
User code 31
User code 32
User code 33
User code 34
User code 39
User code 40
User code 41
User code 42
332
333
334
335
340
341
342
343
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
13
15
19
21
User code 11
User code 12
User code 13
User code 14
User code 19
User code 20
User code 21
User code 22
312
313
314
315
320
321
322
323
14
16
User code 35
User code 36
User code 37
User code 38
User code 43
User code 44
User code 45
User code 46
User code 47
User code 48 /
(Duress)
See next page
336
337
338
339
344
345
346
347
348
349
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
___/___
___/___
___/___
___/___
/_
___/___
___ __
___/___
___/___
/_
___/___
___ __
20
22
23
PG748ES
- 5 -
REPORTING CODES:
(reset code )
"empty"
Streamline
section Streamline
section
Data Data
Description Description
Address Address
DISARMING CODES:(opening)
___/___
___/___
/_
___/___
___ __
User code 21
User code 22
User code 23
User code 24
372
373
374
375
29
___/___
___/___
/
___/___
___ ___
User code 1
User code 2
User code 3
User code 4
352
353
354
355
___/___
___/___
/_
___/___
___ __
User code 25
User code 26
User code 27
User code 28
376
377
378
379
24
30
User code 5
User code 6
User code 7
User code 8
User code 13
User code 14
User code 15
User code 16
356
357
358
359
364
365
366
367
User code 29
User code 30
User code 31
User code 32
User code 37
User code 38
User code 39
User code 40
380
381
382
383
388
389
390
391
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
25
27
31
33
User code 9
User code 10
User code 11
User code 12
User code 17
User code 18
User code 19
User code 20
360
361
362
363
368
369
370
371
26
28
User code 33
User code 34
User code 35
User code 36
User code 41
User code 42
User code 43
User code 44
User code 45
User code 46
User code 47
User code 48 /
(Duress)
384
385
386
387
392
393
394
395
396
397
398
399
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
___/___
___/___
___/___
___/___
___/___
___/___
/_
___/___
___ __
___/___
___/___
/_
___/___
___ __
32
34
35
Espload
Master
See previous page
350
351
___/___
___/___
Streamline
section Streamline
section
Data Data
Description Description
Address Address
ALARM CODES ZONE 1 TO 12: ALARM CODES ZONE 13 TO 24:
___/___
___/___
/
___/___
___ ___
Zone 5
Zone 6
Zone 7
Zone 8
404
405
406
407
___/___
___/___
/_
___/___
___ __
Zone 13
Zone 14
Zone 15
Zone 16
Keypad 1
Keypad 2
412
413
414
415
37
39
Zone 9
Zone 10
Zone 11
Zone 12
408
409
410
411
Zone 17
Zone 18
Zone 19
Zone 20
416
417
418
419
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
38
40
Zone 21
Zone 22
Zone 23
Zone 24
420
421
422
423
___/___
___/___
/
___/___
___ ___
41
Zone 1
Zone 2
Zone 3
Zone 4 (fire)
400
401
402
403 (see add.100)
___/___
___/___
___/___
___/___
36
23
PG748ES
- 6 -
REPORTING CODES:
(reset code )
"empty"
Streamline
section
Streamline
section
Streamline
section
Streamline
section
Data
Data
Data
Data
Description
Description
Description
Description
Address
Address
Address
Address
ZONE 1 TO 12 RESTORE CODES:
ZONE 1 TO 12 SHUTDOWN CODES:
ZONE 13 TO 24 RESTORE CODES:
ZONE 13 TO 24 SHUTDOWN CODES:
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
Zone 5
Zone 6
Zone 7
Zone 8
Zone 5
Zone 6
Zone 7
Zone 8
428
429
430
431
452
453
454
455
___/___
___/___
/_
___/___
___ __
___/___
___/___
/_
___/___
___ __
Zone 13
Zone 14
Zone 15
Zone 16
Keypad 1
Keypad 2
Zone 13
Zone 14
Zone 15
Zone 16
Keypad 1
Keypad 2
436
437
438
439
460
461
462
463
43
49
45
51
Zone 9
Zone 10
Zone 11
Zone 12
Zone 9
Zone 10
Zone 11
Zone 12
432
433
434
435
456
457
458
459
Zone 17
Zone 18
Zone 19
Zone 20
Zone 17
Zone 18
Zone 19
Zone 20
440
441
442
443
464
465
466
467
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
44
50
46
52
Zone 21
Zone 22
Zone 23
Zone 24
Zone 21
Zone 22
Zone 23
Zone 24
444
445
446
447
468
469
470
471
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
47
53
Zone 1
Zone 2
Zone 3
Zone 4 (fire)
Zone 1
Zone 2
Zone 3
Zone 4
424
425
426
427 (see add. 100)
448
449
450
451
___/___
___/___
___/___
___/___
___/___
___/___
___/___
___/___
42
48
Streamline
section Streamline
section
Data Data
Description Description
Address Address
TAMPER 1 TO 12 TROUBLE CODES: TAMPER 13 TO 24 TROUBLE CODES:
___/___
___/___
/
___/___
___ ___
Tamper 5
Tamper 6
Tamper 7
Tamper 8
476
477
478
479
___/___
___/___
/_
___/___
___ __
Tamper 13
Tamper 14
Tamper 15
Tamper 16
484
485
486
487
55
57
Tamper 9
Tamper 10
Tamper 11
Tamper 12
480
481
482
483
Tamper 17
Tamper 18
Tamper 19
Tamper 20
488
489
490
491
___/___
___/___
/
___/___
___ ___
___/___
___/___
/
___/___
___ ___
56
58
Tamper 21
Tamper 22
Tamper 23
Tamper 24
492
493
494
495
___/___
___/___
/
___/___
___ ___
59
Tamper 1
Tamper 2
Tamper 3
Tamper 4
472
473
474
475
___/___
___/___
___/___
___/___
54
DECIMAL PROGRAMMING
3 Digit Decimal Value Programming
Used to program addresses 044 to 061. Values entered must contain 3 digits between "000" and "255". ([10] = 0)
Decimal value programming:
1) Press [ENTER]+ installer code. ([ENTER]key will flash.)
2) Enter 3 digit address (044 to 061).
3) Current value will be displayed on keypad.
4) Enter 3 digit DECIMAL value.
5) Repeat from step 2 onward for next address.
To exit programming mode press [CLEAR].
044: ___/___/___ (hours) Auto arm time (between "000" and "023")
045: ___/___/___ (minutes) Auto arm time (between "000" and "059")
046: ___/___/___ (days) Auto test report every ? days (between "001" and "255") (000 = disabled)
047: ___/___/___ (hours) Auto test report (between "000" and "023")
048: ___/___/___ (minutes) Auto test report (between "000" and "059")
- 7 -
PG748ES
DECIMAL PROGRAMMING
049: ___/___/___ (seconds) Exit delay
(factory default 60 seconds)
050: ___/___/___ (seconds) Entry delay 1
(factory default 45 seconds)
051: ___/___/___ (seconds) Entry delay 2
(factory default 45 seconds)
052: ___/___/___ (minutes) Bell cut-off time
(factory default 5minutes)
053: ___/___/___ ( x 15 mSec.) Zone speed
(factory default 600 mSec.)
054: ___/___/___ (minutes) Power failure report delay
(factory default 30 minutes)
(000 = disabled)
055: ___/___/___ ( x 15 minutes) "No movement" report time
(factory default 8hours)
(000 = disabled)
056: ___/___/___ PGM timer setting (001 to 127 for seconds and 129 to 255 for minutes)
(factory default 5seconds)
Add 128 to desired value in minutes (i.e. for 5 minutes: enter 5 + 128 = 133)
057: ___/___/___ Intellizone delay (in seconds, minimum = 10 seconds)
(factory default 48 seconds)
058: ___/___/___ Installer code lock (147 = locked, 000 = unlocked)
059: ___/___/___ (seconds) Programmable delay before alarm transmission (5 to 63 seconds) (000 = disabled)
060: ___/___/___ (seconds) Recent closing delay (000 = disabled)
061: ___/___/___ Future Use
FEATURE SELECT PROGRAMMING
Addresses 062-126.
"
ON
"
/
"
OFF
"
status of the key lights determines feature selection.
In programming mode, enter 3 digit memory address (062 to 126). To save entries, press
[ENTER
].
To exit programming mode press
[CLEAR].
Reset =
"
OFF
"
for addresses 062 to 126.
Addresses 080 to 085 for future use.
- 8 -
PG748ES
[5]
[2]
[4]
[2]ND
[1]
[3]
[6]
[11][11]
[8]
[10][10]
[7]
[9]
[12][12]
-9-
stayarm/SystemA
enabled
enabled
Bellsquawkonarm/disarm
Autozoneshutdown
See"Reporting"table
(1:1.5)PulseUSA(1:2)PulseEurope
enabledenabled
enabled
Autoarmontime
Autoarmonnomovement [5]
[2]
Keyswitch=regulararm
[4] enabledCallback
[2]ND
[1]
See"TLM"table
[3] enabled
Keyswitcharming
[6]
generatesonlyareport
Silentzone/panicgeneratesasilentalarm
[11][11]
[8]
[10][10]
[7]
Pulsedialing
Partitioning Tonedialing(DTMF)
enabled
[9]
[12][12]
086: KEY
OFF/ONOFF/ON
onlyafteralarm
audible
enabled
audible
enabled
fire
onzoneclosure
4digit
enabled
enabled
enabled
088: OFF/ONOFF/ON
enabled
enabled
KEY
noEOL
Reportzonerestoreonbellcut-off
TamperRecognition
Automaticeventbuffertransmission
Alwaysreportdisarm
Panic2silent
Panic1silent
Panic3silent
6digitaccesscodes
Keyregulararm[10]
KeystayorsystemAarm[11]
Beeponexitdelay
ZoneswithEOL(1K)W
(keys&)[1][3]
(keys&[4][6])
(keys&)[7][9]
Address086,Key[2][1]ND
REPORTINGOPTIONS
Regularreporting
Reportingdisabled
Splitreporting:Alarms
Systemreport
Doublereporting
1,2,1,2,1,2,1,2,failtocomm.
1,1,1,1,1,1,1,1,failtocomm.
2,2,2,2,2,2,2,2,failtocomm.
1,1,1,1,1,1,1,1,failtocomm.,
2,2,2,2,2,2,2,2,failtocomm.
*
Onalarm,allreportsaremadetoTel.#1untilsystemisdisarmed.
(Oncedisarmed,systemreportsaremadetoTel.#2)
*
Address086,Key[11][12]
N/A N/A
090:
Excludepowerfailurefromtroubledisplay OFF/ONOFF/ON
[3]
[1] enabled
[2] stay/SystemA
Autoarm=regulararm
KEY
[6] tamperfollowszonebypassdefinitionNotamperbypass [5]
[4]
enabled
enabled
enabled
enabled
[7]
[8]
[9]
[10]
[11]
[12]
FEATURESELECTPROGRAMMING (continued)
(On/offstatusofkeylightsdetermineswhichfeatureisselected.)
Keypad1zonesupervision
Audibletroublewarning
Duress
Keypad2zonesupervision
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A N/A
N/A
Keypadsoftwareversionspriorto 4.0 Keypadsupervisionmustbe OFF
}
Keypadsoftwareversionsonward4.0 Keypadsupervisionmustbe ON
}(SeeWiringDiagram)
PG748ES
TAMPER/WIREFAULTDEFINITIONS
**
**
Address088,Key[10][11]
*
*
Note: Do not use the Intellizone feature and an entry delay for the same zone, otherwise an alarm may occur as a user
tries to disarm the system.
KEY ACCESS PROGRAMMING
Programs features quickly, without entering addresses or section numbers.
To activate “key access programming”, press [ENTER], followed by installer, master or user code 1. (Code required
depends on the feature you wish to access - see below.) Press the key corresponding to the desired feature.
Press [ENTER]or [CLEAR]to exit.
key
[8] Installer test mode
(installer code only)
In installer test mode, a confirmation beep (intermittent) indicates test is "on", a "rejection" beep (long)
indicates test is "off". The bell will squawk during walk testing to indicate opened, functional zones.
[9] "Auto arming" time program
(all 3 codes)
Key [9] flashes. Enter two digits (00 to 23) for hours + 2 digits (00 to 59) for minutes.
[MEM]"Panel time" and clear "trouble 8"
(all 3 codes)
Key [MEM]flashes. Enter two digits (00 to 23) for hours + 2 digits (00 to 59) for minutes.
[BYP]Test report
(all 3 codes)
Reporting is enabled at address 086, keys [11], [12]. A value must be entered at address 512, and both
telephone and account numbers must be programmed.
[TRBL]Call Espload via telephone
(all 3 codes)
Panel identifier and PC password (addresses 004-007) and computer telephone number (addresses 008-015)
must be programmed.
[AWAY]Answer Espload
(all 3 codes)
This feature is available when using the ADP-1 adapter. In Espload, "blind dial" must be activated in "modem
setup" section, and panel phone number programmed (works also without ADP-1).
[STAY]Cancel communication attempts
(master code and user 1 can only stop calls to Espload)
Until next reportable event
(installer code - all communications)
When communicating with Espload, it is impossible to enter programming mode.
PG748ES
- 10 -
The system hardware will recognize the following zone conditions:
Note: Keypad zones always use (1K OHM) EOL resistor.
SINGLE ZONE CONNECTIONS
ZONE connection, without EOL resistor (N.C. contacts)
address 088, key [MEM] = "on"
key [10] = "off" (reset)
key [11] = "off" (reset)
N.C. contacts see Figure 1
ZONE connection, with EOL resistor (N.C. and N.O. contacts)
address 088, key [MEM] = "off" (reset)
key [10] = "off" (reset)
key [11] = "off" (reset)
N.C. and/or N.O. contacts, see Figure 2
ZONE connection, without EOL resistor, with tamper recognition (N.C. contacts)
address 088, key [MEM] = "on"
key [10] =
key [11] =
Tamper transmits separate code, see Figure 3
ZONE connection, with EOL resistor, with tamper recognition, and with wire fault
(short circuit) recognition (N.C. contacts)
address 088, key [MEM] = "off"
key [10] =
key [11] =
Tamper/wire fault transmits separate code, see Figure 4
- 11 -
PG748ES
See "Tamper/wire Fault Definitions
and Options"
See "Tamper/wire Fault Definitions
and Options"
ESPRIT 748ES CONNECTION DIAGRAMS
ESPRIT748ES WIRINGDIAGRAM
BLACK
RED
Caution: Disconnectbatterybeforereplacingfuse.
BRN
GRY
GRN
RED
"TLM"LED
Shortflash=OK
Longflash=Fault
OFF=Disabled
Constant=OnLine
COM
COMZ1 Z2 Z3 Z4 Z5 Z6COM COM COM COM COM
COMCOMCOMCOMCOMCOM
AC AUX AUX
AUX AUXAUX
BELL
PG1 PG2
N.C. N.0.
BATT
GRN YEL
+AC AC
BATT
5AMP
DIALER
Warning:
Disconnecttelephone
linebeforeservicing.
xxx-xx
xxx
Zone
13or14
KEYSWITCHCONNECTION
KEYSWITCH KYPDGRN
KYPDBLK
220W
N.C.
N.O.
1K
EOL
W
*
Zone13 Zone14
Keypadsoftwareversionspriorto 4.0 Keypadsupervisionmustbe OFF
}
Keypadsoftwareversionsonward4.0 Keypadsupervisionmustbe ON
}
*
(SeeAddress,key)090[11][12]
FIRERESET
ToprogramPGM1toconduct4secondsmokedetectorresetwhen
andarepressedsimultaneously:[][]CLEARENTER
Address=(firstdigit)
Address=
039[]
040[5][10]
BYP Address=
Address=
042[2][6]
056[10][10][4]
ND
Forresistorvalues,
referto639
installationmanuals.
Keyswitchcanbeusedin
parallelwithkeypad(Noton
ULsystems).
GROUNDSTARTCIRCUIT
RNG
WHT
BLK RED
YEL
MR3-UL
+AUX
PGM
FIREALARMZONECONNECTIONS
*PGMmaximum50mA
Smokedetector
powersupervision
relay,12VDC
COM
Smoke
detector
Smoke
detector
PGM Z3
AUX
+
1K
EOL
W
Smokedetectormustbe4wirelatching-
ULFalconmodel5454,ULCBRK2412.
PowersupervisionrelaymodelMR3-UL.
*WHT
BLK RED
MR3-UL
+AUX
PGM
PGMOUTPUTRELAY
YELBRN
COM N.C. N.O.
780IndustrialBlvd.,St-Eustache,Montreal,Quebec,CanadaJ7R5V3Fax:(450)491-2313http://www.paradox.ca ParadoxSecuritySystemsGraphicDept
PRINTEDINCANADA-09/01
Tometallicenclosure
andgroundingrod
TRANSFO
A.C.
POWER
16VAC75VA
UL:K12ModelT16V75
ULC:FrostModelFTC7516Q
Warning: Improperconnectionmay
resultindamagetothesystem.
BELLOUTPUT1Amax.
UL/ULC:650mAmax.24hr.stanby.Belloutput
willshutdownifcurrentexceeds3A.
Smokeandheatdetectors
EOL
RES
N.O.contacts
*Zone3=Firezoneifzone
definitionis"24hour".
1KW
GREEN
Canbeusedasadditional
aux.powerterminals
AUXPOWER1.2Amax.
UL/ULC225mAmax.for24hr.standby.
Ifyouhaveadditionalwiringtoconnectto
auxiliarypower,youcanusethered(+)and
black(-)keypadconnectors.Aux.powerwill
shutdownifcurrentexceeds3A.
BELL
SIREN
Batterychargingcurrent
Jumperoff:350mA
Jumperon:700mA
Charging
and
batterytest
LED
(every60seconds)
SERIAL
OUTPUT
RESET
JUMPER
DIALER
RELAY
+
UL/ULC:Wheelock46T-12 KEYPAD
639
MAX2persystem KEYPAD
616/636/646
MAX5persystem
NotpermittedonULlistedsystems
NOTE: Keypadzonesshouldbe
programmedas24hr.zones.not
**
**
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

PARADOX Esprit 748ES Programming Manual

PARADOX
Brand
PARADOX
Model
Esprit 748ES
Category
Touch screen monitors
Type
Programming Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents