Gigabyte G481-S80 User manual

G481-S80

Dual LGA3647 Sockets Motherboard for Intel® Xeon® Processor Scalable Family Processors

User Manual

Rev. 1.1

Copyright

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without

prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of documentation:

 User Manual: detailed information & steps about the installation, conguration and use of this

product (e.g. motherboard, server barebones), covering hardware and BIOS.



User Guide: detailed information about the installation & use of an add-on hardware or

software component (e.g. BMC rmware, rail-kit) compatible with this product.

 Quick Installation Guide: a short guide with visual diagrams that you can reference easily for

installation purposes of this product (e.g. motherboard, server barebones).

Please see the support section of the online product page to check the current availability of these

documents.

For More Information

For related product specications, the latest rmware and software, and other information please visit our website at

http://www.gigabyte.com

For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller

portal: http://reseller.b2b.gigabyte.com

For further technical assistance, please contact your GIGABYTE representative or visit

https://esupport.gigabyte.com/ to create a new support ticket

For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:

server[email protected]

Conventions

The following conventions are used in this user's guide:

NOTE!

Gives bits and pieces of additional

information related to the current topic.

CAUTION!

Gives precautionary measures to

avoid possible hardware or software problems.

WARNING!

Alerts you to any damage that might

result from doing or not doing specic actions.

Server Warnings and Cautions

Before installing a server, be sure that you understand the following warnings and cautions.

WARNING!

To reduce the risk of electric shock or damage to the equipment:

• Do not disable the power cord grounding plug. The grounding plug is an important safety

feature.

• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

• Unplug the power cord from the power supply to disconnect power to the equipment.

• Do not route the power cord where it can be walked on or pinched by items placed against it.

Pay particular attention to the plug, electrical outlet, and the point where the cord extends from

the server.

WARNING!

To reduce the risk of personal injury from hot surfaces, allow the drives

and the internal system components to cool before touching them.

WARNING!

This server is equipped with high speed fans. Keep away from hazardous

moving fan blades during servicing.

CAUTION!

• Do not operate the server for long periods with the access panel open or removed. Operat-

ing the server in this manner results in improper airow and improper cooling that can lead to

thermal damage.

• Danger of explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent type recommended by the manufacturer.

• Dispose of used batteries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)

CAUTION!

ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU

PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,

PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-

TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER

WHEN HANDLING PARTS.

Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by

their edges without any component and pin touching. After removing a board from its protective

wrapper or from the system, place the board component side up on a grounded, static free sur-

face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over

any surface.

System power on/o: To remove power from system, you must remove the system from

rack. Make sure the system is removed from the rack before opening the chassis, adding, or

removing any non hot-plug components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be

present on power, telephone, and communication cables. Turn off the system and disconnect the

cables attached to the system before servicing it. Otherwise, personal injury or equipment dam-

age can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage drives,

boards, and other parts. We recommend that you perform all procedures in this chapter only at

an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic

wrist strap attached to chassis ground (any unpainted metal surface on the server) when handling

parts.

ESD and handling boards: Always handle boards carefully. They can be extremely

sensitive to electrostatic discharge (ESD). Hold boards only by their edges. After removing a

board from its protective wrapper or from the system, place the board component side up on a

grounded, static free surface. Use a conductive foam pad if available but not the board wrapper.

Do not slide board over any surface.

Installing or removing jumpers: A jumper is a small plastic encased conductor that slips

over two jumper pins. Some jumpers have a small tab on top that can be gripped with ngertips

or with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when

using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with

the pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the

jumper, causing intermittent problems with the function con-trolled by that jumper. Take care to

grip with, but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the

board may bend or break.

CAUTION!

Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery

only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-

teries according to the manufacturer’s instructions.

- 7 -

Table of Contents

Chapter 1 Hardware Installation ...................................................................................11

1-1 Installation Precautions .................................................................................. 11

1-2 Product Specications .................................................................................... 12

1-3 System Block Diagram ................................................................................... 15

1-4 NV Link Diagram ............................................................................................ 16

Chapter 2 System Appearance ..................................................................................... 17

2-1 Front View ...................................................................................................... 17

2-2 Rear View ....................................................................................................... 18

2-3 Front Panel Buttons and LEDs ....................................................................... 19

2-4 Front System LAN LEDs ................................................................................ 20

2-5 Rear System LAN LEDs ................................................................................. 20

2-6 Power Supply Unit (PSU) LED ....................................................................... 21

2-7 Hard Disk Drive LEDs .................................................................................... 21

2-8 Memory Status LED ....................................................................................... 22

Chapter 3 System Hardware Installation ......................................................................23

3-1 Removing the Top Rear Cover ....................................................................... 24

3-2 Removing and Installing the Air Duct ............................................................. 25

3-3 Installing the CPU and Heatsink .................................................................... 26

3-4 Installing the Memory ..................................................................................... 28

3-4-1 Six Channel Memory Conguration ........................................................................28

3-4-2 Installing a Memory ...............................................................................................29

3-4-3 DIMM Population Rule ............................................................................................29

3-4-4 DIMM Population Table .........................................................................................30

3-4-5 Intel Optane DCPMM DIMM Population Rule ........................................................31

3-5 Installing the GPU Card (SXM2 Card) and Heatsink ..................................... 32

3-6 Installing the LAN Card (PCIe x16 Card) ....................................................... 37

3-7 Installing the 2.5" Hard Disk Drive.................................................................. 38

3-8 Replacing the System FAN Module ............................................................... 39

3-9 Removing the Top Front Cover ...................................................................... 40

3-10 Replacing the Power Supply .......................................................................... 41

3-11 Cable Connections ......................................................................................... 42

3-11-1 Motherboard to SXM2 Board ..................................................................................42

3-11-2 Motherboard to 2.5" HDD Backplane Board ...........................................................43

3-11-3 Motherboard to Power Board .................................................................................44

- 8 -

3-11-4 SXM2 Board to Power Board .................................................................................45

Chapter 4 Motherboard Components ...........................................................................46

4-1 Motherboard Components ............................................................................. 46

4-2 Jumper Settings ............................................................................................ 47

Chapter 5 BIOS Setup ..................................................................................................48

5-1 The Main Menu .............................................................................................. 50

5-2 Advanced Menu ............................................................................................. 53

5-2-1 iSCSI Conguration ................................................................................................54

5-2-2 Intel(R) Virtual RAID on CPU .................................................................................55

5-2-3 Intel(R) I350 Gigabit Network Connection ..............................................................56

5-2-4 VLAN Conguration ................................................................................................58

5-2-5 Intel(R) Omni-Path HFI 100 Series .........................................................................61

5-2-6 Intel(R) Ethernet Controller X550 ...........................................................................63

5-2-7 LSI SAS3 MPT Controller SAS3008 .......................................................................65

5-2-8 Trusted Computing .................................................................................................66

5-2-9 Serial Port Console Redirection .............................................................................67

5-2-10 SIO Conguration ...................................................................................................70

5-2-11 PCI Subsystem Settings .........................................................................................71

5-2-12 Network Stack Conguration ..................................................................................73

5-2-13 Post Report Conguration ......................................................................................74

5-2-14 NVMe Conguration ...............................................................................................75

5-2-15 USB Conguration ..................................................................................................76

5-2-16 Chipset Conguration .............................................................................................77

5-3 Chipset Setup Menu ....................................................................................... 78

5-3-1 Processor Conguration .........................................................................................79

5-3-2 Common RefCode Conguration ...........................................................................81

5-3-3 UPI Conguration ...................................................................................................82

5-3-4 Memory Conguration ............................................................................................83

5-3-5 IIO Conguration ....................................................................................................85

5-3-6 Advanced Power Management Conguration ........................................................87

5-3-7 PCH Conguration .................................................................................................90

5-3-8 Miscellaneous Conguration ..................................................................................92

5-3-9 Server ME Conguration ........................................................................................93

5-3-10 Runtime Error Logging ...........................................................................................94

5-3-11 Power Policy ...........................................................................................................96

5-4 Server Management Menu ............................................................................. 98

5-4-1 System Event Log ................................................................................................100

5-4-2 View FRU Information ..........................................................................................101

5-4-3 BMC VLAN Conguration .....................................................................................102

5-4-4 BMC Network Conguration .................................................................................103

- 9 -

5-4-5 IPv6 BMC Network Conguration .........................................................................104

5-5 Security Menu .............................................................................................. 105

5-5-1 Secure Boot .........................................................................................................106

5-6 Boot Menu .................................................................................................... 108

5-6-1 UEFI NETWORK Drive BBS Priorities ................................................................110

5-6-2 UEFI Application Boot Priorities .................................................................. 111

5-7 Save & Exit Menu ......................................................................................... 112

5-8 BIOS POST Codes ...................................................................................... 114

5-8-1 AMI Standard - PEI ...............................................................................................114

5-8-2 AMI Standard - DXE .............................................................................................114

5-8-3 AMI Standard - ERROR .......................................................................................116

5-8-4 Intel UPI POST Codes .......................................................................................... 117

5-8-5 Intel UPI Error Codes ...........................................................................................117

5-8-6 Intel MRC POST Codes .......................................................................................118

5-8-7 Intel MRC Error Codes .........................................................................................118

5-8-8 Intel PM POST Codes ..........................................................................................119

5-8-9 Intel PM POST Codes ..........................................................................................119

5-9 BIOS POST Beep code (AMI standard) ....................................................... 120

5-9-1 PEI Beep Codes ...................................................................................................120

5-9-2 DXE Beep Codes .................................................................................................120

5-10 BIOS Recovery Instruction ........................................................................... 121

- 10 -

This page intentionally left blank

- 11 - Hardware Installation

1-1 Installation Precautions

The motherboard/system contain numerous delicate electronic circuits and components which

can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully

read the service guide and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist

strap, keep your hands dry and rst touch a metal object to eliminate static electricity.

•

Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power

supply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your

hardware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

.

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to

system components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

Chapter 1 Hardware Installation

Hardware Installation - 12 -

1-2 Product Specications

CPU 2nd Generation Intel® Xeon® Scalable and Intel® Xeon® Scalable Processors

Intel® Xeon® Platinum Processor, Intel® Xeon® Gold Processor, Intel® Xeon®

Silver Processor and Intel® Xeon® Bronze Processor

NOTE: If only 1 CPU is installed, some PCIe or memory functions might be

unavailable.

Socket 2 x LGA 3647

Socket P0

Mounting pitch: Narrow ILM

TDP up to 205W

Chipset Intel® C621 Express Chipset

Memory 24 x DIMM slots

DDR4 memory supported only

6-channel memory architecture

RDIMM modules up to 32GB supported

LRDIMM modules up to 64GB supported

Support Intel® Optane™ DC Persistent Memory

1.2V modules: 2933 (1DPC)/2666/2400/2133 MHz

NOTE:

1. 2933MHz for 2nd Generation Intel® Xeon® Scalable Processors only

2. Intel® Optane™ DC Persistent Memory for 2nd Generation Intel® Xeon®

Scalable Processors only

LAN Rear Side:

1 x 10/100/1000 management LAN

Front Side:

2 x 1Gb/s BASE-T LAN port (Intel® I350-AM2)

1 x 10/100/1000 management LAN

4 x QSFP28 LAN port with Intel® Omni-Path Host Fabric Interface (optional)

- 25Gb/s bandwidth per port, total 100Gb/s bandwidth with 4 QSFP28 ports

NOTE: Please select Intel® Xeon processors with Omni-Path Architecture to

enable Intel® Omni-Path Host Fabric Interface

Expansion Slot 8 x SXM2 socket (Gen3 x8 bus) for NVIDIA Tesla® V100/P100 SXM2 module

Rear Side:

4 x PCIe x16 (Gen3 x16 bus) half-length low-prole slot

1 x OCP mezzanine slot

- PCIe Gen3 x8

- Type1, P1, P2, P3, P4, K2, K3

Front Side:

1 x PCIe x16 (Gen3 x8 bus) half-length low-prole slot

Video Integrated in Aspeed® AST2500

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp, DDR4 SDRAM

- 13 - Hardware Installation

Storage 10 x 2.5" hot-swappable HDD/SSD bay

- 2 x amber HDD tray compatible with NVMe devices only

- 2 x amber HDD tray compatible with NVMe, SATA/SAS devices

- 6 x blue HDD tray compatible with SATA/SAS devices only

NOTE: SAS card is required to enable the SAS devices support.

SATA Supported

RAID SATA/SAS drives:

Intel® SATA RAID 0/1/5/10

NVMe drives:

Intel® Virtual RAID On CPU (VROC) RAID 0, 1, 5

NOTE: VROC module is compatible with Intel® SSD only.

Internal I/O 1 x TPM header

1 x VROC connector

1 x Front VGA header

1 x Serial header

12 x System fan connector (23000rpm)

Front Panel

LED/Button/

Port/Connector

2 x USB3.0 port

1 x VGA connector

3 x RJ45 LAN connector with LED

4 x Omni-Path QSFP28 LAN port (reserved)

1 x Power button with LED

1 x ID button with LED

1 x Reset button

1 x NMI button

1 x System status LED

1 x HDD access LED

1 x Omni-Path activity LED

Rear Panel

LED/Button/

Port/Connector

1 x MLAN (reserved, enabled by cable switch)

Backplane I/O 2 x port compatible with NVMe only

2 x hybrid port compatible with NVMe and SATA/SAS

6 x port compatible with SATA/SAS only

TPM 1 x TPM header

TPM2.0 kit: CTM010 (optional)

Hardware Installation - 14 -

System

Management

Aspeed® AST2500 management controller

Avocent® MergePoint IPMI 2.0 web interface:

Network settings

Network security settings

Hardware information

Users control

Services settings

IPMI settings

Sessions control

LDAP settings

Power control

Fan proles

Voltages, fans and temperatures monitoring

System event log

Events management (platform events, trap settings, email settings)

Serial Over LAN

vKVM & vMedia (HTML5)

Power Supply 4 x 2200W redundant PSU

80 PLUS Platinum

AC Input:

- 100-127V/ 14A, 47-63Hz

- 200-240V/ 12.6A, 47-63Hz

DC Output:

- Max. 1200W/ 100-127V, +12.12V/ 95.6A, +12Vsb/ 3.5A

- Max. 2200W/ 200-240V, +12.12V/ 178.1A, +12Vsb/ 3.5A

NOTE: The system power supply requires C19 type power cord.

Operating

System

Compatibility

Windows Server 2012 R2 (x64) Update 1

Windows Server 2016

Red Hat Enterprise Linux 6.9 (x64)

Red Hat Enterprise Linux 7.3 (x64)

SUSE Linux Enterprise Server 11.4 (x64)

SUSE Linux Enterprise Server 12.2 (x64)

Ubuntu 16.04.2 LTS (x64)

VMware ESXi 6.5

Ambient

Temperature

Relative

Humidity

Operating temperature: 10°C to 35°C

Non-operating temperature: -40°C to 60°C

Operating humidity: 8% - 80% (non-condensing)

Non-operating humidity: 20% - 95% (non-condensing)

System

Dimension

4U

447 (W) x 175.2 (H) x 822.15 (D) (mm)

17.60 (W) x 6.90 (H) x 32.37 (D) (inch)

Gross weight: 57kg

* We reserve the right to make any changes to the product specications and product-related information without prior

notice.

- 15 - Hardware Installation

1-3 System Block Diagram

2A~2D

PCIe3.0 x8

PCIe x16 slot (Gen3 x8)

(Front side, support MD2 card)

2/3 x UPI @9.6/10.4 GT/s

PCIe2.0 x4

2 x USB3.0/USB2.0

2 x1G Base-T LAN

(Front Side)

PCIe2.0 x1

2 x USB2.0

LPC/eSPI

Intel I350

NCSI

BMC

ASPEED

AST2500

MLAN

10/100/1G

PHY(1ch)

MAC

DMI3 x4

2 x USB 3.0

(Front Side)

BIOS

SPI Flash 32MB

VGA

TPM

10 x SATAIII

PCIe3.0 x8

8-bay 2.5" SATA + 2-bay 2.5" SATA/NVMe +2-bay 2.5" NVMe

PCH

Intel C621

Lewisburg

PCIe3.0 x16

PLX

PCIe3.0 x16

PCIe3.0 x8

PLX PLX

PCIe x8 Proprietary slot

(Rear side, for OCP LAN card)

PCIe x16 slot

(Inﬁniband)

PCIe x16 slot

(Inﬁniband)

PCIe x16 slot

(Inﬁniband)

PCIe x16 slot

(Inﬁniband)

NVLINK

PLX

GPU#0 GPU#1 GPU#6 GPU#7GPU#2 GPU#3 GPU#4 GPU#5

Skylake SP

Cascade Lake SP

LGA3647 (Socket P0)

CPU0

Skylake SP

Cascade Lake SP

LGA3647 (Socket P0)

CPU1

6-Channel DDR4

12 x DIMM slots

6-Channel DDR4

12 x DIMM slots

Hardware Installation - 16 -

PCIe

Switch

PCIe

Switch

PCIe

Switch

PCIe

Switch

GPU

2

GPU

0

GPU

3

GPU

1

CPU

0

CPU

1

GPU

4

GPU

6

GPU

5

GPU

7

UPI / QPI

PCIe Gen3 x16 @ 8Gb/s

Pascal: 4 NVLinks @ 40GB/s

Volta: 6 NVLinks @ 50GB/s

1-4 NV Link Diagram

- 17 - System Appearance

Chapter 2 System Appearance

2-1 Front View

• Go to the section 2-3 Front Panel Buttons and LEDs for detail description of function

LEDs.

12 3 4 5 6

7

HDD #0

HDD #1

HDD #2

HDD #3

HDD #4

HDD #5

HDD #6

HDD #7

HDD #8

HDD #9

No. Description No. Description

1. PCIe Card Slot 5. USB 3.0 Port x 2

2. Front Panel LEDs and Buttons 6. VGA Port

3. 1 GbE LAN Port x 2 7.

2.5-inch HDD Bay x 10 (#0 to #9)

*SATA supported only: #0 to #5

*Both SATA and NVMe supported: #6 to #7

*NVMe supported only: #8 to #9

4. 10/100/1000 Server Management LAN Port

System Appearance - 18 -

2-2 Rear View

5

6

4 3

12

PSU #1PSU #2PSU #3PSU #4

No. Description No. Description

1. PCIe x16 Slot x 2 (for LAN card) 4. OCP Card Slot (optional)

2. PCIe x16 Slot x 2 (for LAN card) 5. 10/100/1000 Server Management

LAN Port (*1)

3. Power Supply Unit x 4 (PSU #1 to #4) 6. LAN Module

NOTE:

*1: An OCP LAN card is required for using the 10/100/1000 server management LAN port on the rear panel.

- 19 - System Appearance

2-3 Front Panel Buttons and LEDs

1

3456

2

No. Name Color Status Description

1. Reset Button -- -- Press this button to reset the system.

2. HDD Status

LED

Green On Indicates locating the HDD.

Blink Indicates accessing the HDD.

Amber On Indicates HDD error.

Green /

Amber Blink Indicates HDD rebuilding.

N/A Off Indicates no HDD access or no HDD error.

3. System

Status LED

Green Solid On Indicates system is operating normally.

Amber

Solid On

Indicates a critical condition, may include:

- System fan failure

- System temperature

Blink

Indicates non-critical condition, may include:

- Redundant power module failure

- Temperature and voltage issue

- Chassis intrusion

N/A Off

Indicates system is not ready, may include:

- POST error

- NMI error

- Processor or terminator is missing

4. NMI Button -- --

Press this button for the server to generate a NMI to the

processor. If multiple-bit ECC errors occur, the server will

effectively be handled.

5. ID Button

with LED -- -- Press this button to activate system identication.

6. Power Button

with LED

Green On Indicates the system is powered on.

Green Blink System is in ACPI S1 slate (sleep mode).

N/A Off Indicates system is not powered on or in ACPI S5 slate

(power off) or system is in ACPI S4 slate (hibernation mode).

System Appearance - 20 -

2-4 Front System LAN LEDs

1 1

1

2 2

2

No. Name Color Status Description

1. GbE Speed

LED

Yellow On 1 Gbps data rate

Green On 100 Mbps data rate

N/A Off 10 Mbps data rate

2. GbE Link /

Activity LED

Green On Link between system and network or no access

Blink Data transmission or reception is occurring.

N/A Off No data transmission or reception is occurring.

2-5 Rear System LAN LEDs

12

No. Name Color Status Description

1. GbE Speed

LED

Yellow On 1 Gbps data rate

Green On 100 Mbps data rate

N/A Off 10 Mbps data rate

2. GbE Link /

Activity LED

Green On Link between system and network or no access

Blink Data transmission or reception is occurring.

N/A Off No data transmission or reception is occurring.

Page is loading ...

Gigabyte G481-S80 User manual

Gigabyte G481-S80 User manual

Related papers

Other documents