Satco 65-960 Operating instructions

Satco
Brand
Satco
Model
65-960
Category
Mounting kits
Type
Operating instructions

This manual is also suitable for

Satco 65-960 is a versatile and durable LED shop light designed for both plug-in and hardwire applications. With its adjustable hook mount and optional ceiling mount, it offers flexible installation options for various indoor environments. The high-pro design provides ample illumination for workshops, garages, and other industrial or commercial spaces. The fixture can be angled up to 50 degrees vertically, allowing for precise light direction. Additionally, the included wire guard and suspension kit enable further customization and protection in specific use cases.

Satco 65-960 is a versatile and durable LED shop light designed for both plug-in and hardwire applications. With its adjustable hook mount and optional ceiling mount, it offers flexible installation options for various indoor environments. The high-pro design provides ample illumination for workshops, garages, and other industrial or commercial spaces. The fixture can be angled up to 50 degrees vertically, allowing for precise light direction. Additionally, the included wire guard and suspension kit enable further customization and protection in specific use cases.

Satco Products, Inc.
Brentwood, NY 11717© Copyright 2023 Satco Products, Inc. 4/23 1
WARNING: Risk of Fire or Electric Shock
• To avoid damage, falling, electric shock or re, do not modify the lamp or
replace accessories without conrming with the supplier rst.
• Only authorized, qualied personnel should install this xture and should
follow the owner’s manual. Any improper installation might cause failure,
electric shock, re or other injury, damage or hazard.
• Disconnect power before installation or any maintenance of the xture.
• Do not dismantle the xture without the supplier’s authorization.
• Do not touch the power supply when the xture is operating.
• The external flexible cable or cord of this xture cannot be replaced; if the
cord is damaged, the xture shall be destroyed.
• Terminal block not included. The electrical tting must be installed by a
licensed electrician.
• For use in environments where an accumulation of non-conductive dust
on the xture may be expected.
IMPORTANT: This product must be installed in accordance with the
applicable installation code by a person familiar with the construction and
operation of the product and the hazards involved. This product is suitable
for 120V only.
LED HI-PRO SHOP LIGHT
Models: 65/960, 65/961, 65/962, 65/963, 65/964, 65/965,
65/970, 65/971, 96/972, 65/973, 65/974, 65/975, 65/956, 95/957, 65/959
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing xture. Retain for future reference.
WIRING DIAGRAM & INSTRUCTIONS
This product is suitable for both plug in and hardwire applications.
For hardwired applications, cut plug and strip back the SVT to
access the leads. Make sure power is off and connect the black
wire to the AC Line, the white to the AC Neutral and the green to
the ground. Make sure all connections are capped and sealed. Turn
power back on.
INSTALLATION: Hook Mount
STEP 1: Screw the hook into the fixture, tighten
and secure.
STEP 2: Hang the fixture on the ceiling hook
or chain.
STEP 3: Connect wires using the wiring diagram and
instructions on gure 1. Make sure connections are
capped and sealed.
120V
Figure1
Satco Products, Inc.
Bre n t wood, NY 11717© Copyright 2023 Satco Products, Inc. 4/23 2
INSTALLATION: Ceiling Mount
Additional Accessories:
STEP 1: Use a pen or sharp tool and mark holes
through the mounting surface on the ceiling and
drill holes. Fix screws into the holes with a hammer.
NOTE: By adjusting the
bracket screws, the xture
can be angled 50° to the
left or right vertically.
STEP 2: Align the bracket hole with screw hole
and push the fixture to one side and secure.
STEP 3: Plug xture into outlet or for hardwired
applications follow instructions on page 1. Make
sure connections are capped and sealed.
To attach the wire guard, use the provided screws to
attach to the pre-tapped holes on the face of the xture.
To attach the suspension kit, use the provided screws to
attach to the pre-tapped holes on the back of the xture.
Wire Guard Installation:
Suspension Kit Installation:
Wire Guard
LED HI-PRO SHOP LIGHT
Models: 65/960, 65/961, 65/962, 65/963, 65/964, 65/965,
65/970, 65/971, 96/972, 65/973, 65/974, 65/975
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing xture. Retain for future reference.
  • Page 1 1
  • Page 2 2

Satco 65-960 Operating instructions

Satco
Brand
Satco
Model
65-960
Category
Mounting kits
Type
Operating instructions
This manual is also suitable for

Satco 65-960 is a versatile and durable LED shop light designed for both plug-in and hardwire applications. With its adjustable hook mount and optional ceiling mount, it offers flexible installation options for various indoor environments. The high-pro design provides ample illumination for workshops, garages, and other industrial or commercial spaces. The fixture can be angled up to 50 degrees vertically, allowing for precise light direction. Additionally, the included wire guard and suspension kit enable further customization and protection in specific use cases.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents