2. Edelbrock
  3. 14651465

Edelbrock 14651465 Operating instructions

  • Hello! I'm your chat assistant. I've reviewed the installation instructions for the Edelbrock Off-Road Needle & Seat Assembly, specifically the Performer Series 1465 model. This document provides step-by-step guidance on replacing the original assembly and setting the correct float level for off-road use. I'm ready to answer any questions you have about the installation process or the features of this product.
  • What is the catalog number of the needle and seat assembly?
    What is the proper off-road float level setting?
    What should I do if I have questions?
BEND HERE MEASURE AT
OUTSIDE END
7/16"
Needle and Seat assembly
Off-Road Needle & Seat Assembly
for Performer Series Carburetors
Catalog # 1465
Installation Instructions
Please study these instructions carefully before installing your Off-Road
needle & seat assembly. If you have any questions, do not hesitate to contact our
Technical Hotline at: (800) 416-8628 from 7:00 am to 5:00 pm, Monday
through Friday, Pacific Standard Time or e-mail us at: [email protected].
Use Owner's Manual supplied with carburetor for disassembly and reassembly.
Remove original needle and seat assembly and replace with #1465 (Figure 1). To
reset float level, see Figure 2 for proper offroad setting (7/16").
OFF-ROAD FLOAT LEVEL
With bowl cover inverted, bowl cover gasket in
place, and weight of float seating needle, there
should be 7/16" between top of each float and bowl
cover gasket (at outer end). The sides of floats
should be parallel to the outer edge of the bowl
cover. To adjust, bend float lever.
CAUTION! DO NOT PRESS NEEDLE INTO
SEAT WHEN ADJUSTING FLOAT LEVEL.
Brochure #63-0162
© 2002 Edelbrock Corporation
Catalog #1465
Rev. 12/02
Figure 1 Figure 2
®
BEND HERE MEASURE AT
OUTSIDE END
7/16"
Needle and Seat assembly
Off-Road Needle & Seat Assembly
for Performer Series Carburetors
Catalog # 1465
Installation Instructions
Please study these instructions carefully before installing your Off-Road
needle & seat assembly. If you have any questions, do not hesitate to contact our
Technical Hotline at: (800) 416-8628 from 7:00 am to 5:00 pm, Monday
through Friday, Pacific Standard Time or e-mail us at: [email protected].
Use Owner's Manual supplied with carburetor for disassembly and reassembly.
Remove original needle and seat assembly and replace with #1465 (Figure 1). To
reset float level, see Figure 2 for proper offroad setting (7/16").
OFF-ROAD FLOAT LEVEL
With bowl cover inverted, bowl cover gasket in
place, and weight of float seating needle, there
should be 7/16" between top of each float and bowl
cover gasket (at outer end). The sides of floats
should be parallel to the outer edge of the bowl
cover. To adjust, bend float lever.
CAUTION! DO NOT PRESS NEEDLE INTO
SEAT WHEN ADJUSTING FLOAT LEVEL.
Brochure #63-0162
© 2002 Edelbrock Corporation
Catalog #1465
Rev. 12/02
Figure 1 Figure 2
®
BEND HERE MEASURE AT
OUTSIDE END
7/16"
Needle and Seat assembly
Off-Road Needle & Seat Assembly
for Performer Series Carburetors
Catalog # 1465
Installation Instructions
Please study these instructions carefully before installing your Off-Road
needle & seat assembly. If you have any questions, do not hesitate to contact our
Technical Hotline at: (800) 416-8628 from 7:00 am to 5:00 pm, Monday
through Friday, Pacific Standard Time or e-mail us at: [email protected].
Use Owner's Manual supplied with carburetor for disassembly and reassembly.
Remove original needle and seat assembly and replace with #1465 (Figure 1). To
reset float level, see Figure 2 for proper offroad setting (7/16").
OFF-ROAD FLOAT LEVEL
With bowl cover inverted, bowl cover gasket in
place, and weight of float seating needle, there
should be 7/16" between top of each float and bowl
cover gasket (at outer end). The sides of floats
should be parallel to the outer edge of the bowl
cover. To adjust, bend float lever.
CAUTION! DO NOT PRESS NEEDLE INTO
SEAT WHEN ADJUSTING FLOAT LEVEL.
Brochure #63-0162
© 2002 Edelbrock Corporation
Catalog #1465
Rev. 12/02
Figure 1 Figure 2
®
BEND HERE MEASURE AT
OUTSIDE END
7/16"
Needle and Seat assembly
Off-Road Needle & Seat Assembly
for Performer Series Carburetors
Catalog # 1465
Installation Instructions
Please study these instructions carefully before installing your Off-Road
needle & seat assembly. If you have any questions, do not hesitate to contact our
Technical Hotline at: (800) 416-8628 from 7:00 am to 5:00 pm, Monday
through Friday, Pacific Standard Time or e-mail us at: [email protected].
Use Owner's Manual supplied with carburetor for disassembly and reassembly.
Remove original needle and seat assembly and replace with #1465 (Figure 1). To
reset float level, see Figure 2 for proper offroad setting (7/16").
OFF-ROAD FLOAT LEVEL
With bowl cover inverted, bowl cover gasket in
place, and weight of float seating needle, there
should be 7/16" between top of each float and bowl
cover gasket (at outer end). The sides of floats
should be parallel to the outer edge of the bowl
cover. To adjust, bend float lever.
CAUTION! DO NOT PRESS NEEDLE INTO
SEAT WHEN ADJUSTING FLOAT LEVEL.
Brochure #63-0162
© 2002 Edelbrock Corporation
Catalog #1465
Rev. 12/02
Figure 1 Figure 2
®
/