Brita PURITY Quell ST User manual

PURITY Quell ST

W a t e r F i l t e r S y s t e m

08/2019

d e u t s c h

e n g l i s h

f r a n ç a i s

n e d e r l a n d s

i t a l i a n o

e s p a ñ o l

p o l s k i

d a n s k

H a n d b u c h

M a n u a l

M o d e d ’ e m p l o i

H a n d b o e k

M a n u a l e

M a n u a l

Podręcznik

M a n u a l

русский язык

Руководство по

эксплуатации

Deutsch Seite 1 – 18

1 Begriffsübersicht

2 Allgemeine Informationen

3 Betriebs- und Sicherheitshinweise

4 Installation

5 Inbetriebnahme eines Neuﬁlters

6 Austausch der Filterkartusche

7 Filterkapazität

8 Instandhaltung

9 Abfragemodus

10 Fehlerbehebung

11 Batterie

12 Technische Daten

13 Bestellnummern

English Page 19 – 36

1 Deﬁnition of terms

2 General Information

3 Operating and Safety Information

4 Installation

5 Commissioning a New Filter

6 Replacing the Filter

7 Filter Capacity

8 Repair

9 Query Mode

10 Troubleshooting

11 Battery

12 Technical Data

13 Order Numbers

14 Information for Australian market

Français Page 37 – 54

1 Eléments

2 Généralités

3 Consignes d’utilisation et de sécurité

4 Installation

5 Mise en service d’un nouveau ﬁltre

6 Remplacement de la cartouche ﬁltrante

7 Capacité de ﬁltration

8 Entretien

9 Mode d’interrogation

10 Dépannage

11 Pile

12 Caractéristiques techniques

13 Références

Nederlands Pagina 55 – 72

1 Overzicht van de begrippen

2 Algemene informatie

3 Bedrijfs- en veiligheidsvoorschriften

4 Installatie

5 Inbedrijfstelling van nieuw ﬁlterpatroon

6 Vervangen van de ﬁlterpatroon

7 Filtercapaciteit

8 Onderhoud

9 Vraagmodus

10 Verhelpen van storingen

11 Batterij

12 Technische gegevens

13 Bestelnummers

Italiano Pagina 73 – 91

1 Panoramica delle deﬁnizioni

2 Informazioni generali

3 Informazioni sul funzionamento e sulla sicurezza

4 Installazione

5 Messa in funzione di un nuovo ﬁltro

6 Sostituzione della cartuccia ﬁltrante

7 Capacità ﬁltrante

8 Manutenzione

9 Modalità di interrogazione

10 Eliminazione dei guasti

11 Batteria

12 Dati tecnici

13 Numeri d‘ordine

14 Ulteriori informazioni sul prodotto

Español Página 92 – 108

1 Términos

2 Información general

3 Indicaciones de funcionamiento y seguridad

4 Instalación

5 Puesta en marcha de un ﬁltro nuevo

6 Cambio del cartucho ﬁltrante

7 Capacidad del ﬁltro

8 Mantenimiento

9 Modo de acceso

10 Solución de fallos

11 Batería

12 Datos técnicos

13 Números de pedido

Polski Strona 109 – 126

1 Przegląd pojęć

2 Informacje ogólne

3 Wskazówki dotyczące użytkowania

i bezpieczeństwa

4 Instalacja

5 Rozruch nowego ﬁltra

6 Wymiana wkładów ﬁltracyjnych

7 Wydajność ﬁltra

8 Konserwacja

9 Tryb odczytu

10 Usuwanie usterek

11 Bateria

12 Dane techniczne

13 Numery zamówień

Dansk Side 127 – 143

1 Oversigt over begreber

2 Generelle informationer

3 Drifts- og sikkerhedshenvisninger

4 Installation

5 Ibrugtagning af et nyt ﬁlter

6 Udskiftning af ﬁlterpatronen

7 Filterkapacitet

8 Vedligeholdelse

9 Kontrolmodus

10 Udbedring af fejl

11 Batteri

12 Tekniske data

13 Bestillingsnumre

Русский язык Страница 144 – 161

1 Термины

2 Общие сведения

3 Руководство по использованию и безопасности

4 Установка

5 Ввод в эксплуатацию нового фильтра

6 Замена фильтрующего картриджа

7 Ресурс фильтра

8 Уход за фильтром

9 Режим запроса

10 Устранение неполадок

11 Аккумулятор

12 Технические параметры

13 Артикулы для заказа

Page is loading ...

P U R I T Y 4 5 0 6 0 0 1 2 0 0

4 5 0



X X

6 0 0 X



X

1 2 0 0 X X



ATTENTION! ATTENTION!

DE

EN : The PURITY replacement cartridge may only be used in combination with the pressure vessel

that has been specically designed for its size.

DE: Die PURITY Filterkartusche darf nur in Kombination mit dem Druckbehälter verwendet

werden, der speziell für ihre Größe ausgelegt ist.

F R : La cartouche PURITY peut être utilisée uniquement avec la chambre de pression qui correspond

à sa taille.

N L : Het PURITY-reservepatroon mag alleen worden gebruikt in combinatie met de drukbehuizing

die speciaal voor die maat is ontworpen.

I T : Il ltro di ricambio PURITY può essere adoperato solo in combinazione con il recipiente a pres-

sione appositamente progettato per la sua capacità.

ES : El cartucho de recambio PURITY solo puede utilizarse junto con el depósito a presión diseñado

especícamente para su tamaño.

P L : Wymienny wkład ltrujący PURITY może być używany jedynie z pojemnikiem ciśnieniowym

o odpowiadających mu rozmiarach.

DK : PURITY udskiftningspatronen må kun anvendes i kombination med trykbeholderen, som er

specielt designet til dens størrelse.

R U : Сменный картридж PURITY можно использовать только с напорным резервуаром,

который был специально разработанный под его размер.

Page is loading ...

19

EN

2 General Information

2.1 Function and Application PURITY Quell ST

The BRITA PURITY Quell ST Water Filter System is used for decarbonisation of drinking water to

prevent limescale deposits in downstream appliances. Depending on the by-pass setting, calcium,

magnesium and metal ions can be selectively removed from the drinking water during the ﬂow pro-

cess. Furthermore, the ﬁlter material reduces cloudiness and organic impurities, as well as contents

which affect taste and odour (e.g. chlorine residues) in the ﬁltrate and bypass water. By-pass settings

on the connector head are used to set the total hardness reduction to the local water hardness or the

requirements of the application in order to achieve an optimum water quality. The ﬁlter systems are

available in 3 different ﬁlter system sizes (PURITY 450, PURITY 600 and PURITY 1200) and each

in the version without integrated measuring and display electronics or with measuring and display

(Advanced Control System, ACS-Technology) electronics.

Filter systems with ACS Technology show you the current remaining capacity and bypass setting of

your ﬁlter cartridge, the set type and size of the ﬁlter system and the last replacement date of the

ﬁlter cartridge. This ensures optimum ﬁlter control and water ﬁltrate quality. Further information on

the ﬁlter system with ACS Technology can be found in Chapter 5.2.

The unique IntelliBypass ensures a constant by-pass proportion over the entire usage periods, irre-

spective of the volumetric ﬂow of the terminal device concerned. The result is a consistently high water

quality speciﬁcally tailored to the application-speciﬁc requirements and the local water conditions.

Typical applications for BRITA PURITY Quell ST water ﬁlter systems are coffee and espresso

machines, hot and cold drinks vending machines as well as steam ovens (combi ovens) and air

humidiﬁers.

The ﬁlter system is designed for limited spaces, especially in drinks machines and kitchen installations

and can be operated horizontally and vertically.

The food quality of BRITA water ﬁlter products has been inspected and conﬁrmed by an independent

institute.

2.2 Guarantee provisions

The PURITY ﬁlter system is subject to the statutory guarantee of 2 years. A guarantee claim may

only be asserted if all of the instructions in this manual are followed and observed.

2.3 Storage/Transport

Adhere to the ambient conditions in the Technical Data (Chapter 12) for storage and transport.

The manual should be seen as part of the product and kept for the whole service life of the ﬁlter

system and passed on to subsequent owners.

1 Deﬁnition of Terms

1

Pressure Vessel

2

Filter Cartridge

3

Pressure Vessel Lid

4

Connector Head

(optionally with measuring unit)

5

Display Unit (optional)

6

Inlet Hose

7

Connection Inlet Hose

8

Terminal Device Connection

9

Flush Valve with Water Outlet

10

Connection of Outlet Hose

11

Filter Change Sticker

12

Kick Loops

13

Ejector Base

14

Display of the Display Unit (optional)

15

Lock

16

Mantle Handle

17

Reducer 1"– 3/4"

18

Transport Protective Cap

19

By-pass Screw

20

Lid Handle

21

Flush Hose

20

EN

2.4 Recycling/Disposal

Disposing of this product and its packaging in the correct manner protects people and the environment.

The battery and display unit must not be burnt and must not be disposed of in domestic waste.

Please ensure that these are disposed of correctly, in accordance with local regulations. See also

Chapter 11.

Used ﬁlter cartridges can be returned to the BRITA addresses listed (see back of the cover).

3 Operating and Safety Instructions

3.1 Qualiﬁed Personnel

Installation, ﬁlter replacement and maintenance of the ﬁlter system may be carried out only by

specialist staff.

3.2 Correct Use

The product can only operated perfectly and safely if it is installed, used and serviced in the manner

described in this manual.

Only solution-speciﬁc BRITA ﬁlter cartridges may be used for the applications listed.

3.3 Liability Exclusion

Installation must be performed precisely in accordance with the instructions in this manual. BRITA

shall not be held liable for any damage, including subsequent damage, arising from the incorrect

installation or use of the product.

3.4 Speciﬁc Safety Information

• Only water of drinking water quality may be used as intake water for the BRITA water ﬁlter

system. The BRITA water ﬁlter system is only suitable for cold water use within the water

intake temperature stated in Chapter 12. No microbiologically impaired water or water of

unknown quality may be used without appropriate disinfection.

• If there are ofﬁcial instructions to boil tap water, BRITA ﬁltered water must also be boiled. When

the requirement to boil water comes to an end, the ﬁlter cartridge must be replaced and the

connections cleaned.

• It is generally recommended to boil tap water for certain groups of people (e.g. people with

weakened immune systems, babies). This also applies to ﬁltered water.

• Note for people with kidney disease or dialysis patients: during the ﬁlter process, the potassium

content may be increased slightly. If you suffer from kidney disease and/or have to stick to

a special potassium diet, we recommend prior agreement with your doctor.

• The water ﬁltrate is classiﬁed in Category 2 according to DIN EN 1717.

• BRITA recommends that the ﬁlter system not be decommissioned for a long period. If the BRITA

ﬁlter system is not used for several days (2–3 days), we recommend that the PURITY Quell ﬁlter

system be ﬂushed with at least x* litres according to the table below. After stagnation periods of

over 4 weeks, the ﬁlter should be ﬂushed with at least x** litres (see table below) or else replaced.

Please also note that the maximum usage period of the ﬁlter cartridge is 12 months (Chapter 6).

Filter system x* ﬂush quantity

after 2–3 days stagnation

x** ﬂush quantity

after 4 weeks stagnation

PURITY 450 6 litres 30 litres

PURITY 600 12 litres 60 litres

PURITY 1200 24 litres 120 litres

• The ﬁlter system is not resistant to heavily concentrated cleaning agents (e.g. bleach, chlorinated

solvents, heavy oxidants) and must not come into contact with them.

• The ﬁlter system must not be opened or dismantled during operation. The ﬁlter cartridge must

not be opened.

• The pressure vessel and the pressure vessel lid of the ﬁlter systems have a service life of up to ten

years (from the date of installation), provided that they are installed and used correctly and the operat-

21

EN

ing conditions outlined in the Technical Data chapter are adhered to. They must always be replaced

after a maximum of ten years. The hoses must be replaced in rotation after a maximum of ﬁve years.

• Production date:

Production code sticker ﬁlter cartridge and box, example: B615002010

6 Production year, here: 2016

15 Production week, here: calendar week 15

002 Batch No. Filter medium, here the second batch ﬁlled in terms of quantity

010 Serial number of the ﬁlter cartridge, here the tenth cartridge from the second batch

Production code sticker connector head - Example: 1001801 E 619316008764

1001801 BRITA identiﬁcation number

E Supplier ID

6 Production year, here: 2016

19 Production week, here: calendar week 19

3 Production day from Monday (1) to Friday (5), here: Wednesday

16 Production year, here: 2016

008764 Serial identiﬁcation number

Production date pressure vessel and pressure vessel lid – example: 1115

11 Production month, here: November

15 Production year, here: 2015

3.5 Safety Assembly Instructions

• The terminal device operated with the ﬁlter must be free of limescale prior to installation.

• The ﬁlter system can also be operated downstream of water softening systems.

• Protect the ﬁlter system from sunlight and mechanical damage. Do not assemble near sources

of heat and open ﬂames.

• A stop valve must be installed before the ﬁlter system intake hose.

• If the water pressure is higher than 6.9 bar or if there are statutory requirements, a pressure

reducer must be installed before the ﬁlter system.

• A non-return valve according to DIN EN 13959 tested by the DVGW has been factory installed

at the water intake of the ﬁlter head.

• When choosing the material for parts that come into contact with water after the BRITA ﬁlter

system, it is important to remember that, due to the process, decarbonised water contains

free carbon dioxide. For this reason, only materials that are compatible with free carbon dioxide

must be used. We recommend the use of BRITA hoses.

• All parts must be installed in accordance with the country-speciﬁc guidelines on the installation

of drinking water facilities.

4 Installation

!

Caution: Prior to installation, read the Technical Data (Chapter 12) and the Operating and Safety

Information (Chapter 3). After the product has been stored and transported at temperatures below

0°C, it must be stored with the original packaging open for at least 24 hours before commissioning.

4.1 Delivery Scope

To install a PURITY Quell new ﬁlter, you need a pressure vessel

1

, ﬁlter cartridge

2

and pressure

vessel lid

3

.

Before installing, remove everything included in the delivery from the packaging and check that

everything is present:

1 x Pressure Vessel

1

1 x Pressure Vessel Lid

3

1 x Filter Cartridge

2

1 x Manual

1 x Carbonate hardness test or total hardness test

If anything is missing, please contact your local BRITA Ofﬁce.

22

EN

4.2 Assembling the Pressure Vessel and the Pressure Vessel Lid

• Stand with both feet on the kick loops

12

.

• Lift the pressure vessel

1

and turn it clockwise until the mantle handles

16

are over the kick loops

12

.

• Remove the transport protective cap

18

from the ﬁlter cartridge.

• Check that the O-ring seal of the ﬁlter cartridge

2

is correctly seated in the

groove and also check for dirt and damage.

Note: the cartridge seat has been lubricated with food-safe lubricant at the

factory.

• Stand on the kick loops

12

with both feet and place the pressure vessel lid

3

on the pressure vessel

1

. The position of the arrow marking on the lid handle

20

must match the “INSERT” groove.

• Press the pressure vessel lid

3

down and turn clockwise until the lock

15

engages.

4.3 Assembly of Inlet and Outlet Hoses

Note: The inlet and outlet hoses are not included in the standard scope of delivery. The use of

BRITA hose sets is recommended (Chapter 13).

• Fit inlet hose

6

at the inlet of the connector head

4

and outlet hose

10

at the outlet of the

connector head

4

.

Note: Inlet “IN” and outlet “OUT” of the connector head

4

are equipped with O-rings as

seals, therefore no additional ﬂat seals may be used here. Check that the O-rings are seated

correctly.

!

Caution: The max. tightening torque at the 1" and 3/4" connections must not exceed 15 Nm!

Only hose connections with ﬂat seals may be used. Hoses with conical screwed connections

damage the ﬁlter head connections and invalidate any guarantee claims. Only hoses that comply

with DVGW-W 543 may be used to connect the device.

Before assembly, note the direction of ﬂow on the upper side of the ﬁlter head, “IN” = water inlet,

“OUT” = water outlet. Prior to installation, note installation dimensions and operating position

(Chapter 12). If no original hoses are used, the 1"–3/4"

17

adapter supplied must be used to ensure

the return valve is sealed correctly (pre-ﬁtted in the water inlet).

5 Commissioning a New Filter

5.1 By-pass setting for ﬁlter systems without and with measuring and display unit

• For PURITY Quell ST ﬁlter systems: identify the local carbonate hardness in degrees of

German hardness °dH (BRITA nomenclature °KH) using the enclosed carbonate hardness test.

• Check the by-pass setting on the by-pass adjuster

19

.

Note: A 30% by-pass setting has been made in the factory, and might be changed to suit the

local carbonate hardness or total hardness and the application (Chapter 7).

23

EN

5.2 Commissioning the ﬁlter systems with measuring and display unit

Representation in operating mode

Local Carbonate

Hardness Set

Type/

By-Pass Proportion

Date Field: Installation or

last ﬁlter change date

Available residual

capacity in litres

Bar Display

Flow Symbol

Carbonate hardness

The units of carbonate hardness or total hardness can be set as required to German °dH (= display

setting °KH, °DH), English (°e = Clark) (= display setting °EH), French (°f) (= display setting °FH),

American (grains per gallon) (= display setting gpg) or international hardness values (mg/l CaCO

3

)

(= display setting mg/L).

If the setting for the type of hardness (= unit) is changed while the ﬁlter is operating, the values that

were set originally are converted automatically.

Bar chart

Representation of the remaining capacity using bar charts. After installation of a new ﬁlter system or

after a ﬁlter change, the symbolised ﬁlter cartridge is completely ﬁlled with 10 bars.

Bypass proportion in percentage

The by-pass proportion is deﬁned as the proportion of decarbonised water in the total amount of

ﬁltrate and is indicated as a percentage.

Flow symbol

When water is removed via the ﬁlter system, a graphic wave is shown on the display.

Available remaining capacity of the ﬁlter cartridge

The remaining capacity of the ﬁlter cartridge is shown in litres or in US gallons, depending on which

has been selected.

When water is removed, it counts backwards in 1 litre or 1 US gallon stages. If the cartridge is

already exhausted, the capacity is indicated as being negative by ﬂashing.

With a remaining capacity of 20% the last two bars in the bar chart start to ﬂash.

With a remaining capacity of 10% the last bar in the bar chart ﬂashes with the two change arrows.

From a remaining capacity of 0% the negative bars and the change arrows ﬂash alternately with

the remaining capacity shown in negative.

Date Field: Installation or

last ﬁlter change date

Local Carbonate

Hardness Set

Type/

By-Pass Proportion

Bar Display

Available residual

capacity in litres

Change arrow

24

EN

If the monthly limit has been reached up to a month before expiry of the set time limit, it is signalled

by the date ﬁeld ﬂashing.

If the monthly limit is 100% reached, it is signalled by alternate ﬂashing of the date ﬁeld and the

change arrows.

If the remaining capacity and the monthly limit are exceeded, the negative remaining capacity and

the date ﬁeld ﬂash alternately with the change arrows.

Date of the ﬁlter commissioning or last ﬁlter cartridge change

The date of ﬁlter commissioning or last ﬁlter cartridge change is indicated as follows:

Example: 28/10/09

28 Day, here the 28th day

10 Month, here October

09 Year, here 2009

Selecting the units of measurement

You can choose between European, American and international units of measurement on the

display.

For European units of measurement: depending on the type of ﬁlter system (STD, STM), select the

speciﬁed unit of measurement for water hardness °KH, °EH, °FH or ° DH. The unit of volume and

date format are then automatically displayed in litres and DD/MM/YY respectively.

For American units of measurement, select gpg (unit of measurement for water hardness); the

unit of volume and the date format are then automatically displayed in US gallons and MM/DD/YY

respectively.

For international units of measurement, select mg/L (unit of measurement for water hardness);

the unit of volume and the date format are then automatically displayed in litres and DD/MM/YY

respectively.

Parameterisation

The following parameters have to be entered:

• Filter system type and size

STD 4 = PURITY 450 Quell ST

STD 6 = PURITY 600 Quell ST

STD 12 = PURITY 1200 Quell ST

STM 4 = PURITY 450 Steam

STM 6 = PURITY 600 Steam

STM 12 = PURITY 1200 Steam

• Water hardness unit and water hardness value

The following units of hardness may be selected for the various types of ﬁlter system:

Unit of carbonate hardness for ﬁlter system types STD and STM:

°KH (German unit of hardness)

°EH (English unit of hardness)

°FH (French unit of hardness)

gpg (American unit of hardness)

mg/L (international unit of hardness)

25

EN

Monthly limit 2–12

Carbonate Hardness Type/Filter System Size

Date ﬁeldExhaustion after months

• Reminder function ﬁlter usage period in months

Irrespective of the remaining capacity display function, you can set a monthly limit of

2–12 months to activate a reminder function for ﬁlter replacement. If the monthly limit has been

reached up to a month before the export of the set time limit, it is signalled by the date ﬁeld

ﬂashing. Factory set to 12 months.

Example: When set to 9 months, the date ﬁeld starts to ﬂash on the display after 8 months.

Operating the display unit

To operate the display unit, it must be removed from the connecting ﬁttings.

Slide the display housing up approx. 10 mm and pull off the display unit.

The display unit is operated using a button on the back of the display unit.

The display unit is supplied in standby mode. To activate the display, press the

button on the back once brieﬂy and then reset after inputting the parameters.

Parameter input water hardness and ﬁlter system size

At this level, parameters needed for operation are set manually.

The type and size of ﬁlter system is selected, the unit of hardness is set, the local carbonate hard-

ness or total hardness of the tap water is entered, and the maximum cartridge service life (monthly

limit) is activated. After this the parameters must be accepted.

• To activate the display, press the back button once

(< 1 second) until the data ﬁeld appears.

< 1 sec

FIN

• Press and hold the button (> 4 seconds and

< 10 seconds) until the parameter input for the ﬁlter

system type and size ﬂashes.

> 4 sec

• Press and hold the button (> 2 seconds) until the ﬁlter

system type (STD, STM) and corresponding value for

the ﬁlter system size (04, 06, 12) has been reached.

> 2 sec

• Press the button once (< 1 second) to access the next

parameter input unit of hardness. The unit of hardness

ﬂashes.

< 1 sec

26

EN

• Press and hold the button (> 2 seconds) until the

desired unit of hardness has been selected.

> 2 sec

• Press the button once (< 1 second) to access the next

parameter input hardness value. The hardness value

input ﬂashes.

< 1 sec

• Press and hold the button (> 2 seconds) until the value

for the water hardness rises and keep it pressed until

the desired value has been reached.

> 2 sec

• Press the button (< 1 second) to access the next

parameter input monthly limit. The monthly limit input

ﬂashes.

< 1 sec

• Press the button (> 2 seconds) and keep it pressed

until the desired value has been reached.

> 2 sec

The set parameters can now be accepted.

If you want to accept the parameters, proceed as follows:

• Press the button once (< 1 second) until the message

“Reset” appears and ﬂashes.

< 1 sec

• Press the button once (> 2 seconds) until the total

capacity (at 0% bypass) and the current date appear.

> 2 sec

The set parameters have been accepted.

Note: If no input is made within 30 seconds, the display will return to standby or operating mode

without accepting amended parameters.

• Insert the display unit from the front at a height of approx. 10 mm and slide down. The loops on

the display part must be inserted in the grooves on the measuring head. Continue with Chapter

5.4 Flushing/Draining for Filter Systems with and without Measuring and Display Unit.

27

EN

5.3 By-pass setting

Determining the by-pass setting

The by-pass setting is identiﬁed according to the application and the carbonate hardness or total

hardness identiﬁed on the basis of the bypass and capacity table (Chapter 7). The by-pass is then

set on the by-pass screw

19

as follows:

Turn the by-pass screw

19

until the desired by-pass (0–50%) agrees with the marking.

!

Caution: Use Allen key 6mm or 7/32".

!

Caution: Never overwind the by-pass screw to avoid any damage.

5.4 Flushing/Bleeding Filter Systems with and without Measuring and Display Unit

Note: A 10 litre bucket is required for ﬂushing/draining.

• Position ﬁlter system horizontally.

• Completely open ﬂush valve

9

.

• Open the inlet valve

7

at inlet hose

6

while holding the ﬂush hose in the

bucket. Flush quantity at least 10 litres with a minimum volumetric ﬂow of 3 l/

min (180 l/h).

• Close ﬂush valve

9

, put ﬁlter system in upright position and empty bucket.

• Carefully open ﬂush valve

9

while holding the ﬂush hose in the bucket. Flush

quantity once again at least 10 litres.

• Close ﬂush valve

9

.

• Check system for any leaks.

• Note installation date of the ﬁlter system and the next exchange date on the enclosed sticker

and attach it to the pressure vessel. Note: There is space for several stickers on the pressure

vessel. Apply the new sticker with the installation date at the top position.

Note: Filter systems without measuring and display units are now ready for operation.

28

EN

• 5.5 Checking initialisation of ﬁlter systems with a measuring and display unit

• By-pass setting in percent, remaining capacity in litres, capacity bars and the current date must

be shown in the display.

• Note: If these values are not shown in the display, the ﬁlter system must be ﬂushed again

(Chapter 5.4) until the values are shown in the display. Filter systems with a measuring and

display unit are now ready for operation. Cf. Chapters 10.6 to 10.8

6 Replacing the Filter Cartridge

!

Caution: The PURITY replacement cartridge may only be used in combination with the pressure

vessel that has been speciﬁcally designed for its size. See cover.

!

Caution: During the exchange, carefully examine all dismantled parts! Faulty parts must be

exchanged and dirty parts should be cleaned. Read the Operating and Safety Information (Chapter 3)

prior to replacement. After the product has been stored and transported at temperatures below 0 °C,

it must be stored with the original packaging open for at least 24 hours before commissioning at the

ambient temperatures stated in Chapter 12.

Filter systems without a measuring and display unit

The ﬁlter cartridge must be replaced after 6–12 months, at the latest 12 months after commission-

ing, irrespective of the level of exhaustion of the ﬁlter system. If the capacity of the ﬁlter cartridge

has already been exhausted (Chapter 7), it must be exchanged earlier.

Filter systems with a measuring and display unit

The ﬁlter cartridge must be replaced no later than 12 months after commissioning, irrespective of

the level of exhaustion of the ﬁlter system. If the capacity of the ﬁlter cartridge has already been

exhausted (Chapter 7), it must be replaced earlier.

If the cartridge is already exhausted, the capacity is indicated as being negative by ﬂashing. No bars

are shown in the display.

If the monthly limit for the cartridge has been exceeded, this is indicated by the date ﬂashing.

Resetting the display unit

To operate the display unit it has to be removed from the connecting ﬁttings. Slide the display

housing up approx. 10 mm and pull off the display unit to the front. The display unit is operated

using a button on the back of the display unit.

• If this button is pressed (> 10 seconds), the data

set on initial installation will be accepted again, and

the capacity, by-pass setting and input date are all

updated.

> 10 sec

Note: This automatically sets the monthly limit to 12 months.

Note: If no input is made within 30 seconds, the display will return to operating mode without

accepting amended parameters.

Insert display unit from front at a height of approx. 10 mm and slide down. The loops on the display

part must be inserted in the grooves on the measuring head.

29

EN

6.1 Removing the Filter Cartridge

• Switch off power supply to the terminal device (remove plug).

• Close inlet valve

7

at inlet hose

6

.

• Place the ﬂushing hose in a bucket and remove pressure from the ﬁlter system by opening the

ﬂush valve. Catch the escaping water in a bucket.

Note: If the escaping water is more than 1 litre, the inlet valve

7

is not completely closed or is

blocked with scale.

• Stand on the kick loops

12

with both feet while opening the pressure vessel

lid

3

by pressing the lock

15

and turning it anticlockwise as far as it will go.

• Place the pressure vessel lid

3

vertically on both lid handles

20

.

Note: Do not turn the lid horizontally on its head.

• Stand on the kick loops

12

with both feet while turning the pressure vessel

1

anticlockwise by

the mantle handles

16

as far as it will go.

• Take your feet off the kick loops

12

and press the pressure vessel

1

down with both hands on

the mantle handles

16

.

• Remove exhausted ﬁlter cartridge

2

from the pressure vessel

1

.

• Place the exhausted ﬁlter cartridge

2

in the sink with the connection facing down to drain the

remaining water (> 5 min.).

• Lock the exhausted ﬁlter cartridge

2

with the transport protective cap

18

of the new ﬁlter

cartridge and return in the original packaging to the appropriate BRITA address listed on the

back of the cover.

6.2 Inserting the Filter Cartridge

• Check the connector seat of the ﬁlter cartridge O-ring

2

in the pressure vessel

lid

1

for dirt and damage.

• Check that the O-ring seal of the ﬁlter cartridge

2

is correctly seated in the

groove and also check for dirt and damage.

Note: The cartridge seat has been lubricated with food-safe lubricant at the

factory.

• Place the new ﬁlter cartridge

2

in the pressure vessel

1

.

• Stand on the kick loops

12

with both feet, lift the pressure vessel

1

turning it

clockwise until the mantle handle

16

is over the kick loops

12

.

• Stand on the kick loops

12

with both feet and place the pressure vessel

lid

3

on the pressure vessel

1

. The positioning of the arrow marking on the

lid handle

20

must line up with the “INSERT” groove.

• Press the pressure vessel lid

3

down and turn clockwise until the lock

15

engages.

• Switch on power supply to the terminal device (plug).

• To ﬂush and bleed the new ﬁlter cartridge

2

carry out the steps described under 5.3.

30

EN

7 Filter Capacity

7.1 Filter Capacity PURITY Quell ST

Carbonate Hardness

in °dH (°KH)

By-pass setting Filter capacity in litres

PURITY 450 PURITY 600 PURITY 1200

4 50% 8250 14100 25800

5 50% 8250 14100 25800

6 50% 8250 14100 25800

7 50% 7071 12086 22114

8 50% 6188 10575 19350

9 50% 5500 9400 17200

10 40% 4217 7207 13187

11 40% 3833 6552 1198 8

12 30% 3077 5260 9624

13 30% 2841 4855 8884

14 30% 2638 4508 8249

15 30% 2462 4208 7699

16 30% 2308 3945 7218

17 30% 2172 3713 6793

18 30% 2052 3506 6416

19 30% 1944 3322 6078

20 20% 1650 2820 5160

21 20% 1571 2686 4914

22 20% 1500 2564 4691

23 20% 1435 2452 4487

24 20% 1375 2350 4300

25 20% 1320 2256 4128

28 20% 1179 2014 3686

31 20% 1065 1819 3329

35 20% 943 1611 2949

By-pass and capacity table for combi ovens and conventional ovens

Depending on machine type, select by-pass setting 10% to achieve optimally treated water for the

combi oven/conventional oven. We will be happy to make speciﬁc recommendations.

Carbonate Hardness

in °dH (°KH)

By-pass setting Filter capacity in litres

PURITY 450 PURITY 600 PURITY 1200

4 10% 4991 8530 15607

5 10% 4991 8530 15607

6 10% 4991 8530 15607

7 10% 4278 7311 13378

8 10% 3743 6397 11706

9 10% 3327 5686 10405

10 10% 2995 5118 9364

11 10% 2722 4652 8513

12 10% 2496 4265 7804

13 10% 2304 3937 7203

14 10% 2139 3655 6689

15 10% 1996 3412 6243

16 10% 1872 3199 5853

17 10% 1762 3010 5508

18 10% 1664 2843 5202

19 10% 1576 2694 4929

20 10% 1497 2559 4682

21 10% 1426 2437 4459

22 10% 1361 2326 4257

23 10% 1302 2225 4071

24 10% 1248 2132 3902

31

EN

Carbonate Hardness

in °dH (°KH)

By-pass setting Filter capacity in litres

PURITY 450 PURITY 600 PURITY 1200

25 10% 1198 2047 3746

28 10% 1070 1828 3344

31 10% 966 1651 3021

35 10% 856 1462 2676

Note: The capacity limits refer to average utilisation of the terminal equipment, do not contain any

ﬁlter ﬂushing and cleaning cycles and depend on local water quality, ﬂow, mains pressure and ﬂow

continuity.

8 Repair

Regularly check the ﬁlter system for leaks. Regularly check the hoses for kinks. Bent hoses must be

replaced.

The complete ﬁlter system must be replaced in rotation after a maximum of ten years.

The hoses must be replaced in rotation after a maximum of ﬁve years.

!

Caution: Prior to changing, read the Technical Data (Chapter 12) and the Operating and Safety

Information (Chapter 3).

Regularly clean the outside of the ﬁlter system with a soft, damp cloth.

!

Caution: Do not use any substances incompatible with the material (Chapter 3.4) or abrasive

cleaning materials.

9 Query Mode

The following data can be queried in the query mode:

Production data

• Brieﬂy press button 1 x (< 1 second), the following message appears.

Serial Appliance Number Battery Service Life

ID Level Production Year

Production year: Example 08 = 2008

Device number: consecutive

Battery useful life: Example 31/12/19 = The battery in the display unit will be exhausted on 31/12/19

and the complete ﬁlter system has reached its max. usage period.

32

EN

Total volume meter

• Brieﬂy press button 2 x (< 1 second), the following message appears.

00 level current data (today)

00 Indicator for current level Filter system size

Current dateTotal volume meter

The total volume meter is managed at this level; it counts up from 0 irrespective of the cartridge change.

Memory Call-Up

In the Memory Call-Up mode, the data of the last 4 ﬁlter cartridges used can be called up.

• Brieﬂy press button 3 x (<1 second) until the following message appears.

-1, -2, -3, -4 level – data of the cartridges used before the current one.

Carbonate hardness By-pass

Total meter reading when

changing the ﬁlter cartridge

Date of inserting the cartridge

alternating

Cartridge indicator Type

At the top left, the indicator for the ﬁlter cartridge (-1 for previous ﬁlter cartridge) is displayed alter-

nately with the carbonate hardness set and the hardness unit. At the top right, the ﬁlter system

size is displayed alternately with the by-pass setting (display 1 s indicator, 1 s carbonate hardness),

at the bottom left, the meter reading when changing the cartridge (-1) and at the bottom right,

the installation date of the cartridge.

Meaning: the ﬁlter cartridge most recently used was a PURITY 1200 cartridge, the ﬁlter cartridge

was inserted on 25/06/09 and operated up to a meter reading of 23166 litres.

The carbonate hardness set was 14°KH and the by-pass measured was 30%.

The same applies to the cartridge(-2), preceding ﬁlter cartridge and the other preceding ﬁlter

cartridges -3, -4.

Error Messages

Error level E1 indicates whether an error has occurred in blend detection.

E1 is activated as soon as the current bypass is not correctly identiﬁed.

The word Start is then displayed together with the date of occurrence.

alternating

As soon as the current bypass setting is identiﬁed correctly again, the error has ended and the Stop

date is added. At error level 01 the Stop and Start display alternates every second.

33

EN

Error level E2 indicates whether and from when until when an error has occurred at the outlet water

meter. Display is similar to level E1.

Program Overview

ID-Information



00 Current level



-1 History level 1



-2 History level 2



-3 History level 3



-4 History level 4



E1 Error inlet metre



E2 Error drainage metre

Filter system type and size 2 sec.



Type of hardness (unit)

and value 2 sec.



Monthly limit 2 sec.



RESET 2 sec.



Parameter acceptance

Operating mode

ParameterisationRetrieval mode

1 x button Press button 4 seconds

30 sec.no activity =

no Parameter acceptance

20 sec. no activity

Carbonate hardness • Ca-

pacity • By-pass • last ﬁlter

change date

10 Troubleshooting

10.1 No water ﬂow

Cause: Water intake closed.

Troubleshooting: Open water intake on the upstream stop valve or inlet valve

7

on inlet hose

6

.

!

Caution: Installation and maintenance of the ﬁlter system may be carried out only by specialist staff.

10.2 No or low water ﬂow in spite of open water intake

Cause: Mains pressure too low.

Troubleshooting: Check mains pressure.

If the fault continues in spite of adequate mains pressure, check the ﬁlter

system and ﬁlter cartridge and change if necessary.

!

Caution: Prior to changing, read the Technical Data (Chapter 12) and the

Operating and Safety Information (Chapter 3).

34

EN

10.3 Leak at Screwed Connections

Cause: Screwed connections not ﬁtted correctly.

Troubleshooting: Check mains pressure. Check all screwed connections and mount according to

Chapter 4.

If the fault continues, exchange ﬁlter system.

!

Caution: Prior to changing, read the Technical Data (Chapter 12) and the

Operating and Safety Information (Chapter 3).

10.4 Leak after Filter Replacement

Cause: O-ring at the ﬁlter cartridge is not seated correctly.

Troubleshooting: Check correct seat of the O-ring (Chapter 6.2).

!

Caution: Prior to dismantling read the data (Chapter 12) and the Operating

and Safety Information (Chapter 3).

10.5 No Display Function

Cause: Battery drained.

Troubleshooting: Replace display unit (Order number see Chapter 13).

Note: When replacing the display unit, follow the enclosed manual.

10.6 Data on Display Flashing

Cause: Monthly limit expired or the remaining capacity of the ﬁlter cartridge is

exhausted (Chapter 5.2).

Troubleshooting: Replace ﬁlter cartridge (Chapter 6).

10.7 Bypass setting in the display does not agree with the setting of the bypass screw

(cf. 10.8/10.9)

Cause: Filter was not commissioned correctly.

Troubleshooting: Flush ﬁlter again (Chapter 5.4). Check data in the display after ﬂushing

(Chapter 5.5).

10.8 Bypass setting in the display does not agree with the setting of the bypass screw

(cf. 10.7/10.8)

Cause: Valve strip of the by-pass setting not set correctly.

Troubleshooting: Flush ﬁlter system again and readjust bypass screw (Chapter 5.3)

11 Battery

The installed battery is designed for a service life of approx. 10 years. The battery and display unit

must not be burnt and must not be disposed of in domestic waste.

To remove the battery, please proceed as follows:

• Remove the screw on the back of the display unit and open and remove the back

of the housing.

• Disconnect the soldered contacts on the battery with side cutters and remove the battery

from the bracket.

• Replace the back of the housing on the display unit and tighten the screw.

Dispose of the battery and display unit following

the local environmental guidelines for battery disposal.

35

EN

12 Technical Data

PURITY Quell ST ﬁlter system

PURITY 450 Quell ST PURITY 600 Quell ST PURITY 1200 Quell ST

MAE*

Distributor

head

MAE*

Distributor

head

MAE*

Distributor

head

Operating pressure 2 bar – max. 6.9 bar

Operating/water temperature 4°C to 30°C

Ambient tempera-

ture during

operation 10°C to 40°C

storage –20°C to 50°C

Flow rate with 1 bar pressure loss 300 l/h 350 l/h 300 l/h 350 l/h 300 l/h 350 l/h

Empty ﬁlter cartridge volume 3.9 l 5.8 l 10.9 l

Weight (dry/wet) 10 kg/12 kg 12 kg/15 kg 18 kg/24 kg

Dimensions 249 mm/222 mm/408 mm 249 mm/222 mm/520 mm 288 mm/255 mm/550 mm

Operating position Vertically or horizontally

Inlet connection G 1"

Outlet connection G 3/4"

* with ACS Technology

System Tested and Certiﬁed

by NSF International against

NSF/ANSI Standard 42 for the

reduction of Chlorine taste and

odor and against CSA B483.1.

Page is loading ...

Brita PURITY Quell ST User manual

Brita PURITY Quell ST User manual

in other languages

Related papers

Other documents