Beninca MATRIX and CP.BULL Owner's manual

CENTRALE DI COMANDO

CONTROL UNIT

STEUEREINHEIT

CENTRALE DE COMMANDE

CENTRAL DE MANDO

CENTRALKA STEROWANIA

L8542124

Rev. 05/07/03

Libro istruzioni

Operating instructions

Betriebsanleitung

Livret d’instructions

Manual de instrucciones

Książeczka z instrukcjami

UNIONE NAZIONALE COSTRUTTORI

AUTOMATISMI PER CANCELLI, PORTE,

SERRANDE ED AFFINI

MATRIX/MATRIX-RE

CP.BULL/CP.BULL-RI

MATRIX CP.BULL

Page is loading ...

4

5

Collegamento dispositivi di sicurezza vericati

Connection of tested safety devices

Anschluss geprüfter Sicherheitsvorrichtungen

Branchement dispositifs de sécurité vériés

Conexión de los dispositivos de seguridad vericados

Połączenia sprawdzanych urządzeń bezpieczeństwa







 







 

   

  

  

  

   

   

  

  

  

   

Page is loading ...

10

11

MATRIX/CP.BULL Control Unit

The MATRIX/CP.BULL electronic control unit can be used to control 1 230Vac motor, with power not exceeding 1000W.

It is provided with “Single fault test” function, in compliance with the Machinery Directive 98/37/EC.

GENERAL WARNINGS

a) The electrical installation and the operating logic must comply with the regulations in force.

b) The leads fed with different voltages must be physically separate, or they must be suitably insulated with additional insulation of

at least 1 mm.

c) The leads must be secured with an additional xture near the terminals.

d) Check all the connections again before switching on the power.

e) The unused N.C. inputs must be bridged.

INPUT/OUTPUT FUNCTIONS

MATRIX/CP.BULL Control Unit

Terminal No. Function Description

1-2 Power supply Input, 230Vac 50Hz (1-Phase/2-Neutral)

3 GND Connection to ground (compulsory)

4-5 Aerial Connection of the insertable radio receiver card (4-signal/5-display).

6-7 RX 2° Ch

Output, second radio channel of the receiver. N.O. voltage-free contact.

This output is not available in CP.BULL-RI and MATRIX control units with built-in receiver.

8-9 24Vac Output: power supply of accessories, 24Vac/500mA max.

10-11

SCA o

Service light

Normally Open (N.O.) free contact. Conguration like SCA (open gate warning LED) or timed

service light (see SERL Logic).

In CP.BULL-RI and MATRIX control units with built-in receiver, this contact can be preset as

output of second radio contact (see 2ChLogic).

12-13 PHOTO TEST

N.O. free contact. It is used to power photocell transmitters in TEST operating mode.

See diagram “Connection of tested safety devices” and TST1 and TST2 Logic.

14 COM Common for control inputs.

15 OPEN Input, OPEN push-button (N.O. contact).

16 CLOSE Input, CLOSE push-button (N.O. contact)

17 Step-by-Step Input, step-by-step push-button (N.O. contact)

18 PED

Input, pedestrian push-button (N.O. contact). It controls the partial opening. Conguration is

through parameter TPED. When TCA time has elapsed (if activated) a closure control signal

is sent.

19 COM Common, for limit switches and safety devices

20 STOP Input, STOP push-button (N.C. contact)

21 PHOT O

Input, (N.C. contact) for safety devices (e.g. photocells).

In the closing phase: the contact opening causes the motor stop. Common: when the photo-

cell is released, the motor inverts the movement direction (open).

In the opening phase: the contact opening causes the motor stop. When the photocell is

released, the motor re-starts the opening operation.

22 SWO Input, OPEN limit switch (N.C. contact)

23 SWC Input, CLOSE limit switch (N.C. contact)

24 PHOT C

Input (N.C. contact) for safety devices (e.g. photocells).

In the closing phase: Conguration through PHTC Logic.

In the opening phase: Conguration through PHTC Logic.

25-26 DAS

Input, safety edge

Resistive edge: “DAS” Jumper closed

Mechanical edge: “DAS” Jumper open

When the edge is activated, the gate movement is stopped and reversed for about 3s.

If the edge is not in use: “DAS” Jumper open, 25-26 terminals are short-circuited.

27-28-29 Motor

Connection of motor 230Vac - single-phase:

27-Phase/28-Common/29-Phase

27-30 Capacitor Connection of capacitor

31-32 Blinker Connection of blinker, 230Vac 40W max.

To check connections:

1) Cut-off power supply.

2) Manually release the wing, move it to approx. half-stroke and lock it again.

3) Reset power supply.

4) Send a step-by-step control signal by pressing the button or the remote control key.

5) The wing should start an opening movement. If this is not the case, invert the movement wires (27< >29) of the motor and the

limit switch wires SWO-SWC (22< >23).

10

11

Fuses

F1 Output protection fuse for motor and blinker

F2 Protection fuse of transformer

F3 Output protection fuse of accessories and signals

Programming

The programming of the various functions of the control unit is carried out using the LCD display on the control unit and setting

the desired values in the programming menus described below.

The parameters menu allows you to assign a numerical value to a function, in the same way as a regulating trimmer.

The logic menu allows you to activate or deactivate a function, in the same way as setting a dip-switch.

Other special functions follow the parameters and logic menus and may vary depending on the type of control unit or the software

release.

The CP.BULL-RI and MATRIX control units are equipped with a built-in radio module to receive both

xed code and variable code control signals with a frequency of 433.92MHz, able to store up to 64 different codes in memory.

The RADIO menu and the 2Ch and CVAR logic are available in these control units only.

The CP.BULL and MATRIX-RE control units are equipped with connector for extractable receiver.

To access programming:

1 Press the button <PG>, the display goes to the rst menu, Parameters “PAR”.

2 With the <+> or <-> button, select the menu you want (PAR>>LOG>>RADIO>>NMAN>>RES)

3 Press the button <PG>, the display shows the rst function available on the menu.

4 With the <+> or <-> button, select the function you want.

5 Press the button <PG>, the display shows the value currently set for the function selected.

6 With the <+> or <-> button, select the value you intend to assign to the function.

7 Press the button <PG>, the display shows the signal “PRG” which indicates that programming has been completed.

Notes:

Simultaneously pressing <+> and <-> from inside a function menu allows you to return to the previous menu without making any

changes.

Simultaneously pressing <+> and <-> when the display is switched off shows the card software release.

Hold down the <+> key or the <-> key to accelerate the increase/decrease of the values.

After waiting 30s the control unit quits programming mode and switches off the display.

Parameters, Logic and Special Functions

The tables below describe the individual functions available in the control unit.

MENU FUNCTION

Settable values

MIN-MAX-(Default)

MEMO

PARAMETERS

TCA

Automatic closure time. It is activated only with “TCA”=ON logic.

At the end of the preset time, the control unit controls a closure operation.

1-240-(40s)

Tped

The area covered by the gate during its partial opening movement (pedestrian)

is adjusted.

20-250-(50 cm)

Tsm

The area covered by the gate during the braking phase is adjusted.

0 = braking disabled

0-250-(0 cm)

PMo

The torque applied to the motor in the opening phase is adjusted.* 1-99-(50%)

PMC

The torque applied to the motor in the closing phase is adjusted *. 1-99-(50%)

Pso

The torque applied to the motor during braking in the closing phase is ad-

justed.*

1-99-(50%)

Psc

The torque applied to the motor during braking in the opening phase is ad-

justed *

1-99-(50%)

SeaU

The intervention threshold of the anti-crashing device (Encoder) during the

phase at normal speed is adjusted.*

1:maximum sensitivity - 99: minimum sensitivity

1-99-(10%)

SEAR

The intervention threshold of the anti-crashing device (Encoder) during braking

is adjusted *.

1:maximum sensitivity - 99: minimum sensitivity

1-99-(10%)

TLS

Activated only with SERL:ON Logic. The activation time of the service light is

adjusted.

1-240-(60s)

Ibra

The force of the motor brake is adjusted.

0: disabled braking - 1:minimum braking - 99: maximum braking

0-99-(50%)

* WARNING:

An incorrect setting of these parameters may result in a danger. Comply with regulations in force!

12

13

MENU FUNCTION

Settable values

ON-OFF-(Default)

MEMO

LOGIC

TCA

The automatic closure is enabled or disabled

On: enabled automatic closure

Off: disabled automatic closure

(ON)

IbL

The multi-at function is enabled or disabled.

On: enabled multi-at function. The P.P. (Step-by-step) impulse or the impulse

of the transmitter have no effect in the opening phase.

Off: disabled multi-at function.

(OFF)

SCL

The rapid closure is enabled or disabled

On: rapid closure is enabled. When the gate is open or moving, the photocell

activation causes the automatic closure of the gate after 3 s. It is activated only

with TCA:ON

Off: rapid closure is disabled.

(OFF)

PP

The operating mode of “P.P. Push button” and of the transmitter are selected.

On: Operation : OPEN > CLOSE > OPEN >

Off: Operation: OPEN > STOP > CLOSE > STOP >

(OFF)

PRE

Forewarning ashing light enabled or disabled.

On: enabled forewarning ashing light. The ashing light is activated 3 s before

the starting of the motor.

Off: disabled forewarning ashing light.

(OFF)

LTCA

During the TCA time, the blinker is enabled or disabled.

On: Activated blinker.

Off: De-activated blinker.

(OFF)

CLOC

The OPEN input mode is selected

On: OPEN input with WATCH function.

To be used for the connection of timed opening/closing. (CLOSED contact -

open gate. OPEN contact - normal operation).

Off: OPEN input with OPEN function.

(OFF)

htr

The Operator function is enabled or disabled.

On: Operator function enabled.

During operation, the OPEN/CLOSE push-buttons must be kept pressed.

Off: Automatic operation.

(OFF)

IBCA

During the TCA phase, the PP and PED controls are enabled or disabled.

On: PP and PED controls are disabled.

Off: PP and PED controls are enabled.

(OFF)

ENC

The Encoder is enabled or disabled.

On: enabled Encoder, braking activated.

Off: disabled Encoder, braking deactivated

(ON)

tri

The TRIAC test is enabled or disabled.

On: Test on: if TRIAC is faulty the motor does not start.

Off: no test on TRIAC is performed.

(OFF)

Cvar

The code programmable transmitters is enabled or disabled.

On: Radio receiver enabled only for rolling-code transmitters.

Off: Receiver enabled for rolling-code and programmable code transmitters

(self-learning and Dip Switch).

OFF

2ch

The second radio channel is enabled or disabled on terminals 10/11 (it can be

used only for control units with built-in receiver).

On: 10/11 output, preset as second radio channel.

The SERL logic should be OFF.

Off: 10/11 output, preset by the SERL Logic.

(OFF)

serL

The service light function to output 10-11 is enabled or disabled.

On: At every operation, the contact is closed for the time preset with TLS pa-

rameter

Use the auxiliary relay to control the light.

Off: the output is provided with SCA function, open gate LED: open contact with

closed gate - ashing light in closing phase - closed contact in opening phase

and open gate. See wire diagram.

(OFF)

12

13

MENU FUNCTION

Settable values

ON-OFF-(Default)

MEMO

LOGIC

TST1

The test of photocells to PHOT O input is enabled or disabled.

On: Test is enabled. If the test is negative, no operation is performed.

Off: Test is disabled.

(OFF)

TST2

The test of photocells to PHOT C input is enabled or disabled.

On: Test is enabled. If the test is negative, no operation is performed.

Off: Test is disabled.

(OFF)

PHTC

The operating mode of the PHOT C input is selected.

On: PHOT C input is activated in both opening and closing phases.

In the opening phase: the contact opening causes the motor stop. When the

photocell is released, the motor restarts in the opening phase.

In closing phase: the contact opening causes the motor stop. When the

photocell is released, the motor inverts the movement direction (open).

Off: The PHOT C input is activated in the closing phase only.

In the closing phase: the contact opening causes the motor stop and the

immediate reversion of the operation direction (open).

(OFF)

MENU FUNCTION

RADIO

PP

By selecting this function, the receiver awaits (Push) for a transmitter code to be assigned to the step-by-step

function.

Press the transmitter key to be assigned to this function.

If the code is valid, it is stored in memory and OK appears.

If the code is not valid, the wording Err is displayed.

2ch

By selecting this function, the receiver awaits (Push) for a transmitter code to be assigned to the second radio

channel.

Press the transmitter key to be assigned to this function.

If the code is valid, it is stored in memory and OK appears.

If the code is not valid, the wording Err is displayed.

CLr

By selecting this function, the receiver awaits (Push) for a transmitter code to be erased from memory.

If the code is valid, it is erase and OK appears.

If the code is not valid or is not in memory, the wording Err is displayed.

RTR

Completely erase the receiver memory. Conrmation of operation is required.

MENU FUNCTION

NMAN

Displays the number of complete cycles (open+close) carried out by the automation.

When the <PG> button is pressed for the rst time, it displays the rst 4 gures, the second time it shows the

last 4. Example <PG> 0012 >>> <PG> 3456: made 123.456 cycles.

RES

RESET of the control unit. ATTENTION!: Returns the control unit to the default values.

Pressing the <PG> button for the rst time causes blinking of the letters RES, pressing the <PG> button again

resets the control unit.

Note: The transmitter codes are not erased from the receiver.

Operating mode with enabled/disabled Encoder

With ENC=ON LOGICS:

- the anti-crashing sensor is activated. Adjust the sensitivity through parameters SEAV and SEAR in compliance with regulations in

force. An accurate adjustment of the motor brake (IBRA parameter) can help to comply with regulations in force.

- if the parameter TSM>0 (braking activated), the rst opening and closing operations are carried out at reduced speed to permit

the self-learning of the gate leaf stroke. If self-learning is not required, the rst operation is carried out at normal speed.

Once the stroke is recorded, the control unit will automatically control braking in both opening and closing phases.

Braking space can be increased or decreases through TSM parameter.

This recording phase is carried out also in case of power failure or activation of braking (TSM from 0 to >0)

With ENC=OFF LOGICS:

- the anti-crashing sensor is deactivated.

- if the parameter TSM>0 (braking activated), the rst operation is carried out at normal speed to permit the self-learning of the

gate leaf stroke.

14

15

Diagnostics

In the event of malfunctions, by pressing key + or - the status of all inputs (limit switches, control and safety) can be displayed. One

segment of the display is linked to each input. In the event of failure it switches on according to the following scheme.

 







 



   

N.C. inputs are represented by the vertical segments. N.O. inputs are represented by the horizontal segments.

For example, with the leaf

completely closed the display

is as follows:

the moment an Open impulse

is given:

during the opening phase: with the leaf completely open:

Error messages

The control unit checks the correct operation of the safety devices. In case of failure, the following messages may appear on the

display:

ERR1 Error, check photocells at PHOT O input.

ERR2 Error, check photocells at PHOT C input.

ERR3 Error, ENCODER

ERR4 Error, TRIAC

Example of programming

Let us suppose it is necessary to:

- set an automatic closing time (TCA) of 100s

- activate pre-blinking

Perform the operations described below step by step:

Step Press Display Notes

1

PAR

First menu

2

TCA

First function of the rst menu

3

040

Value currently set for the function selected

4

100

Set the desired value with the <+> and <-> keys

5

PRG

The value is programmed

TCA

When programming has been made, the display goes to the function just set

6

PAR

Press <+> and <-> simultaneously to go to the higher menu

7

Log

Second menu

8

TCA

First function of the second menu

9

Pre

Press <-> several times to select PRE logic

10

OFF

Value currently set for the function selected

11

ON

Set the desired value with the <+> and <-> keys

12

PRG

The value is programmed

Pre

When programming has been made, the display goes to the function just set

13

PAR

Press <+> and <-> simultaneously to go to the higher menu and quit programming or wait

30s.

Page is loading ...

Beninca MATRIX and CP.BULL Owner's manual

Beninca MATRIX and CP.BULL Owner's manual

in other languages

Related papers

Other documents