Avangarde LBWC644SB2 User manual

Avantgarde

MANUELD’INSTRUCTION/INSTRUCTIONMANUAL

REFROISSEURAVIN2ZONES/BUILT‐INWINECOOLER



MODELES/MODELS:TBWC‐44SF/LBWC‐44SB



Pour une utilisation optimale de cet appareil ainsi que pour votre sécurité, veuillez lire attentivement les

instructions contenues dans ce manuel avant de faire fonctionner cet appareil.

To ensure proper use of this appliance and your safety, please read the following

instructions completely before operating this appliance.

Page is loading ...

TABLE OF CONTENTS

1.IMPORTANT SAFETY PRECAUTIONS………………….…….……………..13

2.INSTALLATION INSTRUCTIONS

BEFORE USING YOUR APPLIANCE…………………………..……………14

FREE STANDING OR BUILT-IN INSTALLATION….………..…….……..14

ELECTRICAL CONNETION ………………………………………….……..15

3.APPLIANCE FEATURES …………………………………………………..15-16

4.OPERATING YOUR APPLIANCE………….………….………………………17

5.COMPONENTS AND PARTS …………………………………….....….......18

6.CARE AND MAINTENANCE

AUTOMATIC DEFROST…………………………................……..……...19

CLEANING ……………………………………………………………...…...19

VACATIONS ……….…………….………..………………......................19

MOVING YOUR APPALICANCE……………………………………..…..…19

ENERGY SAVING TIPS……………………………………………..…..….19

7.TROUBLESHOOTING GUIDE…………………………………………….…..20

12

1. IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of fire, electrical shock, or injury when using your appliance, follow these basic

precautions:

This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

BEFORE USING YOUR WINE COOLER

 Remove the exterior and interior packaging.

 Before connecting the Wine Cooler to the power source, let it stand upright for approximately 4 hours.

This will reduce the possibility of a malfunction in the cooling system from handling during

transportation.

DANGER OR WARNING: RISK OF CHILD ENTRAPMENT

 Children should not be allowed to operate, play with, or crawl inside the unit.

 Danger: Risk of child entrapment.

 Before throwing away your unit, you must: a) Take off the door; b) Leave the shelves in place, so that

children may not easily climb inside.

 Read all instructions before using the appliance.

 An individual properly grounded branch circuit or circuit breaker is recommended.

 Do not use extension cords.

 Do not place or store anything on top of the unit.

 Never clean appliance parts with flammable fluids. The fumes can create a fire hazard or explosion.

 Make sure the unit is unplugged before cleaning, or repairing.

 Do not store or use gasoline or any other flammable vapors in the vicinity or any other appliance. The fumes

can help create a fire or explosion.

 It is important that the appliance be leveled to work properly.

 Be sure the front of the appliance is unobstructed for air circulation and proper access to the door. Do not

install where it will be subject to direct sunlight, heat or moisture.

 If you do not plan on using the appliance for an extended period of time, unplug it and leave the door open.

 Repair should only be made by authorized Service Centers only.

 If the supply cord is damaged it must be replaced by the manufacturer, its Service Agent or similarly

qualified persons in order to avoid a hazard.

 In order to function at its highest potential, this wine cooler needs to be placed on flat floor and the front of

the unit completely unobstructed.

 This unit should only be used as specified. The manufacturer will not be held responsible for any damage

due to improper use or repairs made by unqualified personnel. A commercial use will void warranty.

13

2. INSTALLATION INSTRUCTIONS

BEFORE USING YOUR APPLIANCE

 Remove the exterior and interior packing.

 Before connecting the appliance to the power source, let it stand upright for approximately 4 hours. This will

reduce the possibility of a malfunction in the cooling system from improper handling during transportation.

 Clean the interior surface with lukewarm water using a soft cloth.

INSTALLATION SPECIFICATIONS

 This appliance requires a standard 115 Volt A.C. /50Hz electrical outlet with three-prong ground。

 This appliance is designed to be installed built-in or free standing.

 Locate the appliance away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct

sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Ambient

temperature below 68°F (20°C) or above 90°F (32°C) will hinder the performance of this appliance. This

unit is not designed for use in a garage or any other outside installation.

 Avoid locating the appliance in moist areas.

 Plug the appliance into dedicated, properly installed-grounded wall outlet. Do not under any circumstances

cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or

grounding should be directed toward a certified electrician or an authorized Service Center. This unit is

not designed to be installed in an RV or used with an inverter.

 After plugging the appliance into a wall outlet, allow the unit to cool down for 3 ~ 4 hours before placing

wine bottles in the appliance.

 This wine cooler come with adjustable legs (in the front) to help level the unit

BUILT-IN INSTALLATION

The cutout dimension illustrated in figure (A) allows for door swing and access to the pull-out shelves when

installed as a built-in appliance. If installing between frameless cabinets, a ½” wide filler strip or side panel may

be needed on the hinge side. The filler strip will act as a spacer between the appliance case and adjacent

cabinet door swing. The width of the opening must include the filter panels.

Note:

The door should protrude at least 1” beyond the surrounding cabinets. The clearance is : 2”

14

23”

34”

231/2”

241/2”

Includinghandle

ELECTRICAL CONNECTION

This appliance should be properly grounded for your safety. The power cord of this appliance is equipped

with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of

electrical shock.

Do not, under any circumstances, cut or remove the third ground prong from the power cord supplied.

The cord should be secured behind the appliance and not left exposed or dangling to prevent accidental

injury.

Never unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from

the receptacle.

Do not use an extension cord with this appliance. If the power cord is too short, have a qualified Electrician

or Service Technician install an outlet near the appliance. Use of an extension cord can negatively affect

the performance of the unit.

3. APPLIANCE FEATURES & STORAGE

TWO TEMPERATURE ZONES

 There are two zones in this appliance(Up zone and down zone)

 Each zone has its independent temperature control and display.

LBWC-44SB UNIT

 For this unit the Up zone can hold up to 16 wine bottles (2 rows of 8 bottles) and the Down zone can hold

up to 28 wine bottles ( 2 rows x 8 bottles , plus 1 row x 12 bottles (6+6 stacked up ))

TBWC-44SF UNIT

 For this unit the Up zone can hold up to 16 wine bottles (2 rows of 8 bottles) and the Down zone can hold up

to 28 wine bottles ( 2 rows x 8 bottles , plus 1 row x 12 bottles (6+6 stacked up ))

ENGAGED WINE SHELVES

 All the shelves have tabs to engage the cabinet on both sides.

 Any of the shelves can be removed to accommodate larger bottles.

TO REMOVE A SHELF FROM A LBWC-44SB UNIT :

 Remove all bottles from the shelves.

 Lift the shelf upwards and then gently pull out the shelf.

WARNING

Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is

damaged, have it replaced by an authorized service center.

15

TO REMOVE A SHELF FROM THE TBWC-30SF UNIT :

 Remove all bottles

 Pull out the shelf

 You can take out shelf by lifting the right side bracket and lowering the left side one(at the same time)

then pull out the shelf smoothly

TO REPLACE A SHELF:

 Place the sides of the shelves back onto the supporting guides of the cabinet and push back until the shelf

tabs slide into place.

NOTE: ENSURE THAT THE TABS ARE FIRMLY ENGAGED IN PLACE BEFORE STORING ANY

BOTTLES.

16

A

B

4. OPERATING YOUR APPLIANCE

Up zone control board Lower zone control board

RECOMMENDED TEMPERATURES FOR CHILLING WINE

Re d W i n e s : 15 - 1 8°C ( 58 - 6 5°F)

Dry/White/Rosé Wines 9-15°C

(48-58°F)

Sparkling Wines 5- 9 ° C

(40- 48°F)

TEMPERATURE CONTROL AND DISPLAY

1. When the unit is plugged indicator will light for 3 seconds (indicating

), and an audible beep will be heard.

2. The temperature in the zone can be controlled and displayed.

3. The temperature in the zone can be set between 39°F to 68°F (4°C to 20°C).

4. The zone temperature may have a difference of +/-5°F (+/-3°C) from setting depending on loading and

ambient conditions.

MEMORY DEVICE

When restart the appliance after a power failure, the last setting will be recover automatically. (Factory setting

will be on in the first use).

If the unit is unplugged, power lost, or turned off; you must wait 3 to 5 minutes before restarting. If you

attempt to restart before this interval the Wine Cooler(compressor) will not start.

When you use the wine Cooler for the first time or restart the Wine Cooler after having been shut off for a

long time, there could be a few degrees variance between the temperature you select and the one indicated

on the LED readout. This is normal and it is due to the length of the activation time. Once the Wine Cooler is

running for a few hours everything will be back to normal.

ON/OFF

Press this key for turn on and turn off appliance. Press and hold it for at least 3 seconds.

INTERIOR LIGHT

To turn on or turn off the interior light, press this key once. The interior light will keep lighting if it is not turn off.

LOCK/UNLOCK FUNCTION

This unit has a lock/Unlock function. If the appliance doesn’t receive any instructions from user over 12

seconds, every key in the control panel will be automatically locked.

To unlock, press and hold (the 2 temperature control keys) at the same time for at least 3 seconds.

17

TEMPERATURE SETTING (COLDER /WARMER)

Under normal conditions the temperature display will flash and indicates the current temperature of the zone.

When pressing either keys the temperature displayed will decrease or increase in increments of one

degree. If the (colder) or (warmer) key is pressed and held for one second, the temperature displayed

will decrease or increase in a speed of one degree per one second. The temperature display will flash 5

seconds after the temperature has been set, and revert to the current temperature.

FAHRENHEIT /CELSIUS SETTING (C°/F°)

The temperature display can be changed between Celsius and Fahrenheit by pressing this key.

5.COMPONENTS AND PARTS

Temperature Control and Display

1. Circulation Fan

2. Interior Light

3. Cabinet

4. Chrome Shelf

5. Wooden shelf

Remark:

Handle or shelf is subject to change according to model .

18

1

2 3

4

5

6

6.CARE AND MAINTENANCE

DEFROST

 The ice build-up on the inner back wall during compressor operation will be automatically defrosted in a

compressor off cycle.

 When defrosting is in process, only the circulation fans for both zones run.

 Defrost water will drain into the drip dish(on the compressor) .and the water will be evaporated by the

compressor

CLEANING YOUR APPLIANCE

 Upon installation of your new appliance, it is recommended that it be cleaned thoroughly.

 Unplug the unit from the wall outlet.

 Remove all contents.

 Wash the inside with a damp warm cloth soaked in lukewarm water and baking soda solution. The solution

should be about 2 tablespoons of baking soda to a quart of water.

 Be sure to keep the door gasket (seal) clean to keep the unit running efficiently.

 The outside of the appliance should be cleaned with mild detergent and warm water.

 Dry the interior and exterior with a soft cloth.

 Dust or anything else blocking the vent may hinder the cooling efficiency of the appliance. Vacuum the vent

if necessary.

VACATION TIME

 Unplug the unit from the wall outlet.

 Remove all the contents.

 Clean the appliance.

 Leave the door open slightly to avoid possible formation of condensation, mold, or odors.

 Short vacations: Leave the appliance operating during vacations of less than three weeks.

 Long vacations: If the appliance will not be used for several months, remove all contents and unplug the

power cord. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave the door open

slightly, blocking it open if necessary.

MOVING YOUR APPLIANCE

 Unplug the unit from the wall outlet.

 Remove all the contents.

 Securely tape down all loose items inside your appliance.

 Tape the doors shut.

ENERGY SAVING TIPS

 The appliance should be located in the coolest area of the room, away from heat producing appliances or

heating ducts, and out of the direct sunlight.

 Ensure that door is closed when the appliance is plugged in.

WARRANTY

Limited warranty, 1 year, parts and labor.

19

7.TROUBLESHOOTING GUIDE

You can solve many common appliance problems easily, saving you the cost of a possible Service Call.

Try the suggestions below to see if you can solve the problem before calling for service.

PROBLEM

POSSIBLE CAUSE

Display flash and indicate “HH”, flash speed

one time per second

The temperature sensor of zone>37°

Display flash and indicate “LL”, flash speed

one time per second

The temperature sensor of zone<0°

Display flash and indicate “E0”, flash speed

one time per second

Connection failure, wire or component is not

connect tightly

Display flash and indicate “E1”, flash speed

one time per second

The temperature sensor is failure in corresponding

zone

Display flash and indicate “E2”, flash speed

one time per second

The defrost sensor (coil senor) is failure in

corresponding zone

Appliance does not operate.

Not plugged in.

The circuit breaker has tripped or there is a blown

fuse.

Temperature inside the appliance is too

warm.

Temperature control is set too warm. Turn the

control to a cooler setting and allow several hours

for the temperature to stabilize.

Door is kept open too long or is opened too

frequently. Warm air enters the appliance every

time the door is opened. Open the door less often.

The door is not closed completely.

The door gasket does not seal properly.

The appliance has recently been disconnected for

a period of time. 4 hours are required for the

appliance to cool down completely.

Temperature inside the appliance is too

cold.

Temperature control is set too cold. Turn the

control to a warmer setting and allow several hours

for the temperature to stabilize.

Vibrations Check to assure that the appliance is on a level

surface.

The appliance is touching the wall. Re-level the

appliance and move it from the wall.

If continued vibration occurs, turn off the appliance

and unplug the power plug. Contact Customer

Service Dept. for further assistance.

Moisture forms on inside appliance walls. Door is slightly open.

Door is kept open too long, or is opened too

frequently. Open the door less often.

The door is not sealed properly.

Moisture forms on outside of appliance. Door is slightly open, causing cold air from inside

the appliance to meet warm moist air from outside.

The door will not close properly. The appliance is not on a level surface.

The gasket is dirty.

TO CONTACT THE AUTHORIZED SERVICE CENTER:

A.G.I SERVICE

450.963.1303/1.888.651.2534

20

Avangarde LBWC644SB2 User manual

Avangarde LBWC644SB2 User manual

in other languages

Other documents