Kohler K-11000-96 Installation guide

Kohler
Brand
Kohler
Model
K-11000-96
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Page is loading ...
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and web site are listed on
the back cover. Thanks again for choosing Kohler Company.
Tools and Materials
Before You Begin
Observe all local plumbing and building codes.
Shut off the main water supply.
If possible, install this faucet before installing the lavatory.
Inspect the supply tubing for damage. Replace as necessary.
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
This faucet is for use on single hole lavatories.
Adjustable Wrench Plumbers Putty Sealant Tape
1035092-2-B 2 Kohler Co.
1. Faucet Installation
Insert the faucet through the top of the lavatory.
From underneath the lavatory, slide the bracket up over the stud.
Tighten the nut securely against the bracket to secure the faucet
into place.
Kohler Co. 3 1035092-2-B
2. Click Drain Installation
CAUTION: Risk of product damage. Never pull on the drain
cap to open the drain. Press and release the drain cap once to
close it. Press and release it again to open it.
Remove the seal from the body.
Apply a 1/2″ (1.3 cm) diameter ring of plumbers putty or other
sealant around the underside of the body, according to the sealant
manufacturer’s instructions.
Insert the body into the lavatory drain hole.
Attach the rubber washer (tapered side up) to the body.
Install the flat washer over the threads of the body.
Partially thread the nut onto the body. Do not tighten at this time.
Orient the ″KOHLER″ logo as desired. Adjustment is not possible
after final assembly.
Wrench-tighten the nut.
Apply sealant tape to the top of the tailpiece threads before
screwing it into the body.
Connect the tailpiece to the body.
Remove any excess putty or sealant.
Rubber Washer
Lavatory
Tailpiece
Nut
Body
Flat Washer
Apply Plumbers
Putty
1035092-2-B 4 Kohler Co.
3. Supply Connections
CAUTION: Risk of restricted water flow and product damage.
Use extreme care when bending the supplies to avoid kinking.
If the lavatory is not installed, install it at this time. Follow the
lavatory manufacturer’s instructions.
Identify your supply connection type.
Connect the supply tubes to the supply stops. (Left is hot - right
is cold.)
Wrench-tighten all connections.
Supply
Stop
Supply
Hose
Kohler Co. 5 1035092-2-B
4. Installation Checkout
Connect the drain tailpiece into the trap. The tailpiece should
extend 1″ (2.5 cm) to 2″ (5 cm) into the trap.
Ensure that all connections are tight.
Open the drain.
Turn on the main water supply and check for leaks. Repair as
required.
Turn on the faucet and run water through the spout for about a
minute to remove any debris. Check for leaks and repair as
needed.
Shut the faucet off.
1035092-2-B 6 Kohler Co.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Kohler K-11000-96 Installation guide

Kohler
Brand
Kohler
Model
K-11000-96
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents