Hypro 9700 Series Aqua Tiger Centrifugal DC Pumps Owner's manual

Brand: Hypro

Model: 9700 Series Aqua Tiger Centrifugal DC Pumps

Type: Owner's manual

pentair.com

INSTALLATION AND

OPERATION MANUAL

AQUA-TIGER CENTRIFUGAL DC PUMPS

9700B



9700S

L-0335C Rev. C (12-09-19)

-2-

1. Alwaysdrainandushthepumpbeforeservicingordisassembling

foranyreason(seeinstructions).

2. Alwaysdrainandushpumpspriortoreturningunitforrepair.

3. Neverstorepumpscontaininghazardouschemicals.

4. Beforereturningthepumpforservice/repair,drainoutallliquidsand

ushtheunitwithneutralizingliquid.Then,drainthepump.Attach

atagorincludeawrittennoticecertifyingthatthishasbeendone.

Pleasenotethatitisillegaltoshiportransportanyhazardouschemicals

withoutUnitedStatesEnvironmentalProtectionAgencyLicensing.

Hazardous Substance Safety Information

Thepumpmustbemountedinadrylocation.Themotorisnotwaterproof;

therefore,itmustnotbesubmerged.Theunitcanbeoperatedinanypositon.

Itisadvantageoustomountthepumpssothewaterdrippingfromaloose

portconnectionwillnotwetthemotor.Thepumpheadmaybemountedat

incrementsonthemotortoallowmountingasneeded.

OPERATION

Trynottorunthepumpdrybecausedoingsoshortenstheseallife.Ifyou

mustrunthepumpdry,dosoonlyforshortperiodsoftime.Thepumpmay

runagainstaclosedoutlet.Smallparticleswillpassthroughthepump,so

a50-meshintakestrainershouldbettedtothepump.

CAUTION: The motor runs hot, up to 180

F on the motor case. Contact

during operation may cause a burn.

ELECTRICAL HOOKUP

WARNING: If the pump is operated in an area containing ammable vapors,

wire leads must be joined by insulated mechanical locking connectors.

Loose or inadequate wire connections can spark resulting in explosion.

Property damage, injury or death may occur.

CAUTION: Lead wires on the motor must not be shortened or the war-

ranty will be voided.

Positiveterminalofthebatteryisconnectedtoanoverloadprotecteddistribution

panel.Theredleadwiththefuseholderisconnectedtothedistributionpanel.

Theblackwireisconnectedtothenegativeterminalofthebattery.Forproper

operation,themotormustrotateclockwisewhenviewedfromthepumpend.

Thepropersizedfusehasbeeninstalledinthefuseholder.Ifthisfuseblows,

replaceitwiththesamesizefuseafterdeterminingthereasonfortheblown

fuse.Usetheproperwiresizeasdeterminedbythewiringtable.

Installation and Operation

Overload Protected

Distribution Panel

Black Wire

Inlet

Outlet

Fuse

Red Wire

Outlet

Wiring Table for 9700B

Connectionlength

betweenbattery WireGage

andmotor

1-10ft. ....................................#12

11-20ft. ...................................#10

12-30ft. ...................................#8

ApproximateAmpDraw ...................... 8

FuseSize.......................................... 10

Fuse Sizes for 9700B

General Safety Information

1. WARNING: DO NOT pump solvents, thinners or gasoline, as

explosion may result causing personal injury or death and/or

property damage. DO NOT use in explosive atmospheres. The

pump should be used only with liquids compatible with the pump

component materials. Failure to follow this warning will void the

product warranty.

2. WARNING: DO NOT operate with any of the mounting bolts

removed from the motor case. Explosion resulting in personal

injury, death or property damage may occur. Case openings

must be sealed to avoid explosion and maintain ignition pro-

tected rating.

3. Donotpumpliquidsattemperatureshigherthantherecommended

maximumtemperatures(140

F).

4. Disconnectpowerbeforeservicing.

5. Drainallliquidsfromthesystembeforeservicinganycomponent.

6. Checkhoseforweakorwornconditionbeforeeachuse.Makecertain

thatallconnectionsaretightandsecure.

7. Periodicallyinspectthepumpandthesystemcomponents.Perform

routinemaintenanceasrequired(seeMaintenancesection).

8. Donotusethesepumpsforpumpingwaterorotherliquidsforhuman

oranimalconsumption.

9. Hypropumpsarenotdesignedtobeusedascleanwaterpumpsas

denedin10CFRParts429and431.

-3-

Ref. Qty. Model 9700B Model 9700S

No. Req'd. Description Part Number Part Number

IMPORTANT:

When ordering parts, give PART NUM-

BER and PART DESCRIPTION. Refer-

ence Numbers are used ONLY to point

out parts in the drawing and are NOT to

be used as ordering numbers.

1 3 CoverScrew 2210-0124 2210-0124

2 1 Cover 19893 23660

3 1 O-ring,Viton* 19898 19898

4 1 Impeller 19892 23659

5 1 MechnicalSealAssy.** N/A 23665S

6 1 PipePlug 00336 21059

7 2 HexHeadScrew 2210-0123 2210-0123

8 1 Housing 19891 23627  

9 1 LipSeal,Viton* 19928 N/A

10 4 Grommet 21138 21138

11 1 Motor12VDC(TENV) 23697S 23697S

12 1 SetScrew 19929 19929

*VitonisatrademarkofE.I.Dupont

deNemourandCompany

TENV=Totally-EnclosedNon-Ventilated

(**)Mechanicalsealshavecarbonceramicwearingfacesand316StainlessSteelspringcomponentswithVitonelastomers.

Manufacturerreservestherighttochangepartswithoutnotication.

Models 9700B and 9700S

-4-

Care of the Pump

AFTER USE PUMP CARE

A. GUMMING—Gummingorcorrosion inside the pump

canbepreventedbythoroughlyushingthepumpclean

withwateroraliquidthatwillneutralizetheliquidpumped.

(Formanyliquids,asolutionof1gallonammoniamixed

with6gallonsofwaterworkswell.)

B. To PREVENT RUST/CORROSION, we recommend

(afterStepA)ushingthepumpwithpermanent-type

automobile radiator antifreeze containing a rust inhibitor,

andthenpreventingairfromgettinginthepump.Usea

50-50solutionofantifreezeandwater.Flushitthroughthe

pump,andthen drainit.Plugtheportstokeepairfrom

gettingintothepumpduringstorage.  Cleaning andrust

protectionshouldbe donewhenthepumpwillbestored

awayformorethantwotothreedays.

Dimensionsareininches.

MAINTENANCE

Checkallelectricalandplumbingconnectionsperiodically.

Insaltwater applications,corrosionofthe electricalcon-

nectionscancausealossofperformanceornon-operation.

Themotorshouldbeprotectedwithacorrosioninhibiting

spray.Anyrustshouldberemovedandthemotorrepainted.

DISASSEMBLY

1. Removethecoverscrews,coverando-ring.

2. Removethepipeplugonthesideofthehousingand

rotatetheimpellersothesetscrewalignswiththeplug

hole.Inserta3/32"allenwrenchthroughtheplughole

andloosentheimpellersetscrew.Removetheimpeller.

3. Remove the screws that secure the housing to the

motor,andremovethehousing.

4. Fromtheinsideofthehousing,insertadowelintothe

sealareaandpressthesealoutofthesealbore.

ASSEMBLY

1. Fromtherearofthehousing,pressthesealintothe

sealborewiththeopenliptowardthepumpcavity.

2. Applyasmallamountofgreasetothemotorshaftinthe

areawherethesealcontactsit.Slidethehousingonto

theshaftandsecureittothemotorwiththe(2)twohex

headscrews.

3. Aligntheimpellersetscrewwiththeatonthemotor

shaftandslidetheimpellerontotheshaftuntilitcon-

tactstherearofthehousing.Slidetheimpellerforward

1/32"-1/16"andsecureitwiththesetscrew.Rotatethe

impellerbyhandtoensurethatitdoesnotrubonthe

housing.Reinstallthepumppluginthehousing.

4. Cleanthesurfacesofthecoverandhousingwherethey

makecontact.Asmallamountofgreaseontheo-ring

will ease installation. Place the o-ring on the cover.

Alignthecoverwiththehousingandsecureitwiththe

(3)threecoverscrews.

Maintenance

Notes

-6-

Notes

-7-

Notes

For a detailed list of where Pentair trademarks are registered, please visit www.pentair.com/en/registrations.html. Pentair trademarks and logos are owned by Pentair PLC. or its aliates.

Third party registered and unregistered trademarks and logos are the property of their respective owners. Because we are continuously improving our products and services, Pentair

reserves the right to change specications without prior notice. Pentair is an equal opportunity employer.

Hypro/Shurflo (hereafter, “Hypro”) agricultural products are warranted to be free of defects in material and workmanship under normal use

for the time periods listed below, with proof of purchase.

- Pumps: one (1) year from the date of manufacture, or one (1) year of use. This limited warranty will not

exceed two (2) years, in any event.

- Accessories: ninety (90) days of use.

This limited warranty will not apply to products that were improperly installed, misapplied, damaged, altered, or incompatible with fluids or

components not manufactured by Hypro. All warranty considerations are governed by Hypro’s written return policy.

Hypro’s obligation under this limited warranty policy is limited to the repair or replacement of the product. All returns will be tested per

Hypro’s factory criteria. Products found not defective (under the terms of this limited warranty) are subject to charges paid by the returnee

for the testing and packaging of “tested good” non-warranty returns.

No credit or labor allowances will be given for products returned as defective. Warranty replacement will be shipped on a freight allowed

basis. Hypro reserves the right to choose the method of transportation.

This limited warranty is in lieu of all other warranties, expressed or implied, and no other person is authorized to give any other warranty or

assume obligation or liability on Hypro’s behalf. Hypro shall not be liable for any labor, damage or other expense, nor shall Hypro be liable for

any indirect, incidental or consequential damages of any kind incurred by the reason of the use or sale of any defective product.

RETURN PROCEDURES

All products must be flushed of any chemical (ref. OSHA section 1910.1200 (d) (e) (f) (g) (h)) and hazardous chemicals must be labeled/tagged

before being shipped

†

to Hypro for service or warranty consideration. Hypro reserves the right to request a Material Safety Data Sheet from

the returnee for any pump/product it deems necessary. Hypro reserves the right to “disposition as scrap” products returned which contain

unknown fluids. Hypro reserves the right to charge the returnee for any and all costs incurred for chemical testing, and proper disposal

of components containing unknown fluids. Hypro requests this in order to protect the environment and personnel from the hazards of

handling unknown fluids.

Be prepared to give Hypro full details of the problem, including the model number, date of purchase, and from whom you purchased your

product. Hypro may request additional information, and may require a sketch to illustrate the problem.

Contact the appropriate Hypro Service Department to receive a Return Merchandise Authorization number (RMA#).

Returns are to be shipped with the RMA number clearly marked on the outside of the package. Hypro shall not be liable for freight damage

incurred during shipping. Please package all returns carefully. All products returned for warranty work should be sent shipping charges

prepaid:

LIMITED WARRANTY ON HYPRO/SHURFLO AGRICULTURAL PUMPS & ACCESSORIES

AMERICAS & ALL OTHER REGIONS

Hypro / Pentair

Attention: Service Department

375 Fifth Avenue NW

New Brighton, MN 55112

Service: 800-468-3428

Fax: 651-766-6618

Technical: 800-445-8360

hypro.technicalpentair.com

CANADA

Pentair Water Belgium B.V.B.A

Industriepark Wolfstee

Toekomstlaan 30, 2200

Herentals, Belgium

Tel: +32 14 259 911

Fax: +32 14 259 975

shuro.service@pentair.com

CENTRAL & SOUTH AMERICA

+55 (11) 3317-5085

vendas.pwdb@pentair.com

pentair.com

†

Carriers, including U.S.P.S., airlines, UPS, ground freight, etc., require specific identification of any hazardous material being shipped. Failure to do so may result in a substantial fine and/or prison term.

Check with your shipping company for specific instructions.