DELTA DORE PACK TYXIA 541 Installation guide

Brand: DELTA DORE

Model: PACK TYXIA 541

Type: Installation guide

PACK TYXIA 541 et 546

Noce d’installaon

Installaon instrucons

Instrukcja instalacji

Installae-instruces

2322

Pack composion Contents

TYXIA 541 pack

TYXIA 546 pack

TYXIA 1712

TYXIA 5630

TYXIA 5730

1/ Remote control installation 24

1.1 Mounted on the wall 24

1.2 Placed on a at surface 24

2/ Receiver installation 25

2.1 Connection instructions

for terminals 1 2 3 4 27

2.2 Connection instructions

for IN1 - COM - IN2 terminals 28

2.3 Connection 29

3/ Wireless association 31

4/ Learning for the

shutter travel time 32

5/ Conguration of TYXIA 5630 or

5730 receivers 33

6/ Create a group 35

7/ Use 37

8/ Troubleshooting 38

9/ Technical characteristics 40

2524

1/ Remote control installa on 2/ Receiver installa on

Recommenda ons

IMPORTANT: the control wires are not insulat-

ed from the mains power supply. All connected

equipment must be marked CE and meet the

requirements of the low voltage devices as well as

assembly recommenda ons.

Local control wires can be extended up to 10 m

(separate from the 230 V).

The roller shu er high and low stops must be set

before the receiver is installed.

Use an electrically

isolated tool to

perform the acons

on the receiver con-

guraon buon.

TYXIA

1.1 Mounted on the wall

1.2 Placed on a flat surface

2726

Installa on

You can install the ligh ng receiver in a

 ush-mounted box, behind a switch or control

push-bu on (automa c detec on on use) or behind

a ceiling.

Switch oﬀ the

installaon power supply

230V~

OFF

2/ Receiver installa on

2.1 Connection instructions

for terminals 1 2 3 4

Strip the wires while respec ng

the strip length speci ed on the

product.

0,75 - 1,5 mm

• Stranded wires• Solid wires

3 4

Using a 2.5 mm screwdriver,

press the terminal buon

then insert the wire.

Push the wire

fully into

the terminal.

Removal recommendaons

Switch o the power supply.

Use a 2.5 mm screwdriver

to press the terminal buon

before removing the wire.

3 4

2928

2/ Receiver installa on

2.2 Connection instructions

for IN1 - COM - IN2 terminals

Use the wires supplied.

Push the wire fully

into the terminal.

Do not strip the wires when they are con-

nected to the product as you

could damage the internal connector.

7mm

0,5 mm

KY31A02

3 4

Removal

recommendaons

Turn the wire

while pulling on it.

3 4

2.3 Connection

Connect the motor control wires

to terminals 3 and 4 (motor lowering control wire

to terminal 3, raising control wire to terminal 4).

Connect the switch to the IN1 - COM - IN2 termi-

nals.

Connect the 230 V power supply to terminals 1

and 2.

Switch the installa on power back on to con nue

with the associa on opera on.

230 V~

IN1

COM

IN2

1 2 3 4

TYXIA

1 2 3 4

IN1

COM

IN2

IN1

COM

IN2

IN1

COM

Hold switch

Double push-but-

ton

Push buon

3130

3/ Wireless associa on

❶ Set all the receivers to associa on standby

mode by pressing their bu on for 3 seconds un l

the LED  ashes.

❷ Press .

❸ On the remote control press and at the

same  me and hold for 3 seconds un l the LED

 ashes, then release.

❹ The blinds are ac vated brie y when the

associa on is completed. The number of

associated items is displayed on the screen (❺).

You can associate up to 16 receivers

(or motors).

> 3s

1 2 3 4 1 2 3 4

... ... ...

> 3s

1 2 3 4

TYXIA TYXIA

3332

4/ Learning for the

shuer travel me

Perform a complete cycle from stop to stop:

❶ Lower or raise the roller shuer completely to

the stop.

❷ Do the reverse acon unl the opposite stop is

reached.

Note

The learning for the shuer travel me adjusts itself

automacally for each complete cycle from stop to

stop.

Do not interrupt the roller shuer travel.

5/ Conguraon of TYXIA 5630 or

5730 receivers

Congure the receiver according to

the type of switch connected

Mode 1 (by default):

Hold switch

Raise/Stop/Lower

Mode 2:

Raise/Lower

double push-buon

Mode 3: Raise/Stop

Lower/Stop push-buon

IN1

COM

IN2

IN1

COM

IN2

IN1

COM

3534

5/ Con gura on of TYXIA 5630 or

5730 receivers

To modify the receiver conguraon

Press the receiver's buon for 6 seconds.

The LED  ashes, then be-

comes steady, release.

The number of  ashes

corresponds to the current

mode.

Brie y press the receiver bu on to select the mode.

Con rm the selected mode by pressing the bu on

for 3 seconds un l the LED switches on.

1 2 3 4

> 6 s

TYXIA

1 2 3 4

TYXIA

1 2 3 4

TYXIA

1 2 3 4

TYXIA

Mode 1 Mode 2 Mode 3

6/ Create a group

Crea ng a group allows the simultaneous control

of mul ple receivers.

❶ Press for 3 seconds un l the symbol

 ashes, then release.

❷ Press as many  mes as required to select

the number of the group to create (e.g. 9).

❸ Select the receiver (or motor) by pressing on

as many  mes as required. The controlled item is

ac vated brie y (roller shu er or ligh ng).

❹ Press to add a group to it.

The screen displays “IN”.

Or press to remove it from the group.

The screen displays “OUT”.

Repeat stages ❸ and ❹ for each receiver (or

motor).

To create another group, repeat stages ❷, ❸ and

❹.

3736

6/ Create a group

You can create up to 16 groups.

A single receiver can be associated with mul ple

groups.

To exit the mode press for 3 seconds.

> 3s

7/ Use

❶ Brie y press .

❷ Press as many  mes as required to select

the number of the group to control:

... : Group 1 to 16

: Group Total

❸ Press , or to control the roller

shu er(s).

The LED indicates that the receivers have

correctly received the informa on.

3938

8/ Troubleshoo ng

The screen displays .

The ba ery is low.

Change the ba ery.

Remove an associaon

Remove the front face of the

remote control.

Press bu on A.

The red LED ﬂ ashes.

Press

as many  mes as

required to select the receiver

to remove.

Press .

Press bu on A to exit.

Remove all associaons

Remove the front face of the remote control.

Press bu on A.

The red LED ﬂ ashes.

Press the

and bu ons at the same  me and

hold for 3 seconds.

Press bu on A to exit.

CR 2430

The receiver locks in oﬀ mode

When an overload is detected, the product locks

in o mode for 30 seconds

before authorising a new ac va on.

The LED  ashes rapidly throughout

this phase:

- For TYXIA 5630 receivers:

- Replace your receiver with a TYXIA 5730.

- For TYXIA 5730 receivers:

Contact our customer service.

An addi onal user guide is available on

the TYXIA 5630 and TYXIA 5730 pages of

the DELTA DORE website.

4140

9/ Technical characteriscs

TYXIA 1712

• Power supplied by 3 V lithium baery, CR2430

• Class III insulaon

• Maximum wireless power < 10 mW

category 2 receiver

• Wireless remote control device, X3D Transmis-

sion frequency: 868.7 MHz to 869.2 MHz

• Wireless range: 100 to 300 metres outside,

variable depending on the associated equipment

(the range can vary depending on the installaon

condions and the electromagnec environment)

• Mounted on a base

• Dimensions: 46 x 121 x 10.7 mm

• Degree of protecon: IP 40

• Operang temperature: 0 °C / +55 °C

• Storage temperature: -10 °C / +70 °C

• Install in an environment with normal polluon

levels.

TYXIA 5630 and TYXIA 5730

• Power supply: 230 V ~ 0.6 VA

• 2 powered contact outputs: TYXIA 5630 (1 A) -

TYXIA 5730 (2 A)

• Stand-by consumpon: 0.06 W

• Number of associated transmiers: 16 maximum

• Storage temperature: -10 °C / +70 °C

• Operang temperature: 0 °C / +55 °C

• IP 40 in a ush mounng box

• Dimensions: 41 x 36 x 14.5 mm

• Maximum wireless power < 10 mW

category 2 receiver.

www.deltadore.com

DELTA DORE PACK TYXIA 541 Installation guide

DELTA DORE PACK TYXIA 541 Installation guide

DELTA DORE PACK TYXIA 541 Installation guide

Related papers

Other documents