Tyan B4881 User manual

Transport TX46

B4881

Service Engineer’s Manual

2

PREFACE

Copyright

This publication, including all photographs, illustrations, and soft-

ware, is protected under international copyright laws, with all rights

reserved. Neither this manual, nor any material contained herein,

may be reproduced without written consent of the manufacturer-.

Version 1.0

Disclaimer

Information contained in this document is furnished by TYAN Com-

puter Corporation and has been reviewed for accuracy and reliability

prior to printing. TYAN assumes no liability whatsoever, and dis-

claims any express or implied warranty, relating to sale and/or use of

TYAN products including liability or warranties relating to fitness for

a particular purpose or merchantability. TYAN retains the right to

make changes to product descriptions and/or specifications at any

time, without notice. In no event will TYAN be held liable for any

direct or indirect, incidental or consequential damage, loss of use,

loss of data or other malady resulting from errors or inaccuracies of

information contained in this document.

Trademark Recognition

All registered and unregistered trademarks and company names

contained in this manual are property of their respective owners

including, but not limited to the following.

TYAN and Transport TX46 are trademarks of TYAN Computer Cor-

poration.

AMD, Opteron, and combinations thereof are trademarks of

Advanced Micro Devices Corporation.

Phoenix BIOS is a trademarks of Phoenix Technologies.

Winbond is a trademark of Winbond Electronics Corporation.

Broadcom is a trademark of Broadcom Corporation and/or its sub-

sidiaries.

ATI and Rage Xl are trademarks of ATI Corporation.

nVIDIA is a trademark of NVIDIA Corporation.

ii

Federal Communications Commission (FCC)

Notice for the USA Compliance Information State-

ment (Declaration of Conformity Procedure) DoC FCC

Part 15: This device complies with part 15 of the FCC

Rules

Operation is subject to the following conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received including inter-

ference that may cause undesired operation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and the

receiver.

– Plug the equipment into an outlet on a circuit different from

that of the receiver.

Consult the dealer on an experienced radio/television technician for

help.

Notice for Canada

This apparatus complies with the Class B limits for radio interference

as specified in the Canadian Department of Communications Radio

Interference Regulations. (Cet appareil est conforme aux norms de

Classe B d’interference radio tel que specifie par le Ministere Cana-

dien des Communications dans les reglements d’ineteference

radio.)

Notice for Europe (CE Mark) This product is in conformity

with the Council Directive 89/336/EEC, 92/31/EEC

(EMC).

CAUTION: Lithium battery included with this board. Do not punc-

ture, mutilate, or dispose of battery in fire. Danger of explosion if bat-

tery is incorrectly replaced. Replace only with the same or

equivalent type recommended by manufacturer. Dispose of used

battery according to manufacturer instructions and in accordance

with your local regulations.

iii

About this Manual

This manual provides you with instructions on installing your

Transport TX46. This manual is intended for experienced users and

integrators with hardware knowledge of personal computers.

This manual consists of the following parts

Chapter 1: Provides an Introduction to the Transport TX46

B4881 barebone, packing list, describes the

external components, gives a table of key compo-

nents, and provides block diagrams of the system.

Chapter 2: Covers procedures on installing the CPU, mem-

ory module, PCI-X card, and hard drive.

Chapter 3: Covers removal and replacement procedures for

p r e - i n s t a l l e d c o m p o n e n t s .

For information on the mainboard, please refer to the attached main-

board user’s manual. You can find the detailed description about

jumper and BIOS settings from the motherboard manual.

iv

Safety Information

Before installing and using the Transport TX46, take note of the fol-

lowing precautions:

– Read all instructions carefully.

– Do not place the unit on an unstable surface, cart, or stand.

– Do not block the slots and opening on the unit, which are pro-

vided for ventilation.

– Only use the power source indicated on the marking label. If

you are not sure, contact the Power Company.

– The unit uses a three-wire ground cable, which is equipped

with a third pin to ground the unit and prevent electric shock.

Do not defeat the purpose of this pin. If your outlet does not

support this kind of plug, contact your electrician to replace

your obsolete outlet.

– Do not place anything on the power cord. Place the power

cord where it will not be in the way of foot traffic.

– Follow all warnings and cautions in this manual and on the

unit case.

– Do not push objects in the ventilation slots as they may touch

high voltage components and result in shock and damage to

the components.

– When replacing parts, ensure that you use parts specified by

the manufacturer.

– When service or repairs have been done, perform routine

safety checks to verify that the system is operating correctly.

– Avoid using the system near water, in direct sunlight, or near

a heating device.

– Cover the unit when not in use.

Chapter 1: Overview 1

Chapter 1: Overview

1.1 About the Transport TX46 (B4881)

Congratulations on your purchase of the TYAN Transport

TM

TX46 (B4881), a highly-optimized rack-mountable barebone

system. The Transport TX46 (B4881) offers the latest proces-

sor server system, providing a rich feature set and incredible

performance. Leveraging advanced technology from AMD

®

,

the Transport TX46 (B4881) server system is capable of

offering scalable 32-bit & 64-bit computing, high-bandwidth

memory design, and a lightning-fast PCI-X & PCI-E bus

implementation. The Transport

TM

TX46 (B4881) not only

empowers your company in today’s demanding IT environ-

ment but also offers a smooth path for future application

usage.

TYAN is also proud to deliver the Transport

TM

TX46 (B4881)

in SATA flavor while supporting up to two hard drives, one

slim CD-ROM and one optional slim floppy disk drive (not

included). The Transport

TM

TX46 (B4881) uses TYAN’s latest

tooling-made chassis featuring a robust structure and a solid

mechanical enclosure. All of this provides the Transport

TM

TX46 (B4881) the power and flexibility to meet the needs of

nearly any server application.

1.2 Features

2 Chapter 1: Overview

1.2 Features

Processors

• (4) mPGA 940-pin ZIF socket

• Supports up to four AMD

®

Opteron™ 800 series processors

• (4) onboard 3-phase VRMs

• 128 bit DDR dual channel memory

controller integrated into CPU

Memory

• Total sixteen 184-pin 2.5V DDR

DIMM sockets (4 for each CPU)

• Support up to 64GB registered DDR

400/333/266 SDRAM support

Chipset

• NVIDIA CrushK8-04 Professional

• AMD-8111™ HyperTransport I/O

Hub

• Winbond W83627HF Super I/O chip

• (3) Analog Devices ADT7468 Hard-

ware Monitoring IC

BIOS

• Phoenix BIOS with 8MB LPC Flash

ROM

• ACPI 2.0 support

• Serial Console Redirect

• USB boot support

• 48-bit LBA support

• Power management: S0, S1, S4 and

S5

Device Bay

• Two HDD bays, fixed type

• Slim CD-ROM, IDE interface

• Optional slim 1.44MB FDD

Chassis

• Industry standard, 19-inch rack

mountable, 2U chassis

• Dimensions

(H)x(W)x(D)=3.5”x17.25”x28”

(89x436x713mm)

Back I/O ports

• Stacked PS/2 mouse and keyboard

ports

• (2) USB 2.0 connectors in rear panel

• (1) 9-pin serial Port

• (1) 15-pin VGA port

• (2) RJ-45 LAN port

Power supply

• Single 2U 850W A/C power supply

w/PFC

• Voltage: 90~264 VAC full range

Front Panel Features

•I/O

- (2) USB 2.0 ports

•LED indicators

- Power LED

- (2) LAN LED

- HDD active LED

- ID LED

• Switches

- Power switch

- Reset switch

- ID LED switch

•

Expansion slots

• (2) x16 PCI Express Slots, one with

x4 signal

• (2) independent 64-bit PCI-X bus

• (1) 64-bit 133MHz (3.3V) PCI-X slot

• (2) 64-bit 100MHz (3.3V) PCI-X slot

• Supports a total of (5) PCI-E/PCI-X

low profile cards

1.2 Features

Chapter 1: Overview 3

Intelligent Platform Management

• Optional Tyan Server Management

Daughter card

Regulatory

• FCC Class B

(declaration of conformity)

• CE (declaration of conformity)

Environment

• Operating: 5

o

C~35

o

C

• Non-operating: -40

o

C ~ 70

o

C

1.3 Unpacking

4 Chapter 1: Overview

1.3 Unpacking

1.3.1 Box contents

This section describes the TX46 package contents and

accessories.

Component Description

Industry standard 2U chassis, (2) fixed HDD

bays

Tyan Thunder K8QW S4881 motherboard

(pre-installed)

24x slim CD-ROM drive (pre-installed)

LED and USB control board (pre-installed)

EPS 12V 850W PSU (pre-installed)

(4) Fans (80 mm x 80 mm)

1.3 Unpacking

Chapter 1: Overview 5

1.3.2 Accessories

2x Mounting Ears 4x CPU Heat Sinks with Fans

2x Sliding Rails

2x Power Cables

2x Screws Kit

Left: Transport TX46 (B4881) Service

Engineer’s Manual

Right: Thunder K8QW (S4881) User’s

Manual

SATA HDD Power Cable

CD-ROM

Diskette

1.3 Unpacking

6 Chapter 1: Overview

1.3.3 Opening the box

Open the box carefully and ensure that all components are

present and undamaged. The product should arrive pack-

aged as illustrated below.

Contact your distributor if anything is missing or appears

damaged.

Packaged box contents

Packaged accessories

1.4 About the product

Chapter 1: Overview 7

1.4 About the product

This section contains hardware diagrams and a block dia-

gram of the TX46 (B4881) system.

1.4.1 System front view

See the diagram below for details of the front panel indicators

and switches.

1.4.2 System rear view

Reset button

Power button

ID button

Power indicator

Internal HDD trays

LAN indicator

ID indicator

HDD indicator

USB ports

Slim CD-ROM driveSlim type FDD bay

(Pre-installed)

AC in socket

Stacked PS/2 mouse and

keyboard ports

USB ports

GbE ports

VGA port

Serial Port

ID LED

1.4 About the product

8 Chapter 1: Overview

1.4.3 System internal view

1 Memory Slots 2 CPU Sockets

3 System Fans 4 CD-ROM Cable

5 Slim Type CD-ROM Drive Bay 6 LED Control Board

7 Slim Type Floppy Drive Bay 8 Power Supply

9 SATA Cables 10 PCI-X/PCI-E Slots

1

2

3

4

6

8

5

10

9

7

1.4 About the product

Chapter 1: Overview 9

1.4.4 Mainboard layout

1.4 About the product

10 Chapter 1: Overview

Jumpers & Connectors

Jumper

/Connector

Function

J115 Front Panel Connector

J20 Clear CMOS Jumper

J1 SMBus Connector

J30, J31, J95 USB 2.0 Header

JP2 Chassis Intrusion Header

J101 Serial Port Internal Header

J11 PCI-X Channel A Frequency Configuration Jumper

J12 PCI-X Channel B Frequency Configuration Jumper

JP1 Wake on Ring PIN Header

JP4, JP5 Gigabit LAN1, LAN2 LED Header

J27, J28 IEEE 1394A Pin Header

J118 / J119 ID Switch / ID LED

J22 NMI (non-maskable interrupt) Header

J117/J116/J108/J

109

CPU Fan Connector

J103/J104/J105/J

106/J107/J110

Chassis 4-Pin Fan Connectors

J111/J112 Chassis 3-Pin Fan Connectors

LPT CON Parallel Header

PWR3 ATX 12V Power Connector

PWR4 1x4-Pin 5V Power Connector

Chapter 2: Setting up 11

Chapter 2: Setting up

2.1 Before you begin

This chapter explains how to install motherboard components

including CPUs, memory modules, and PCI cards. There are

also instructions in this section for installing SATA, SCSI, and

IDE hard drives.

Careful attention should be given to the precautions men-

tioned in this section when setting up your system.

2.1.1 Work area

Make sure you have a stable, clean working environment.

Dust and dirt can get into components and cause malfunc-

tions. Use containers to keep small components separated.

Putting all small components in separate containers prevents

them from becoming lost. Adequate lighting and proper tools

can prevent you from accidentally damaging the internal

components.

2.1.2 Tools

The following tools will be required to complete the installa-

tions described in this chapter.

• A cross head (Phillips) screwdriver

• A grounding strap and/or anti static pad

Most of the electrical and mechanical connectors in your sys-

tem can be disconnected using your fingers. It is recom-

mended that you do not use needle-nosed pliers to remove

connectors as these can damage the soft metal or plastic

parts of the connectors.

2.1 Before you begin

12 Chapter 2: Setting up

2.1.3 Precautions

Components and electronic circuit boards can be damaged

by static electricity. Working on a system that is connected to

a power supply can be extremely dangerous. Follow the

guidelines below to avoid damage to the Transport TX46 or

injury to yourself.

• Disassembly of this system should only be attempted

by experienced engineers.

• Ground yourself properly before removing the top

cover of the system. Unplug the power from the

power supply and then touch a safely grounded

object to release static charge (i.e. power supply

case). If available, wear a grounded wrist strap. Alter-

natively, discharge any static electricity by touching

the bare metal chassis of the unit case, or the bare

metal body of any other grounded appliance.

• Avoid touching motherboard components, IC chips,

connectors, memory modules, and leads.

• The motherboard is pre-installed in the system.

When removing the motherboard, always place it on

a grounded anti-static surface until you are ready to

reinstall it.

• Hold electronic circuit boards by the edges only. Do

not touch the components on the board unless it is

necessary to do so. Do not flex or stress circuit

boards.

• Leave all components inside the static-proof packag-

ing that they ship with until they are ready for installa-

tion.

• After replacing optional devices, make sure all

screws, springs, or other small parts are in place and

are not left loose inside the case. Metallic parts or

metal flakes can cause electrical shorts.

• Always use the correct size screws and fixings when

installing or replacing components.

2.2 Installing motherboard components

Chapter 2: Setting up 13

2.2 Installing motherboard components

This section describes how to install CPUs, memory mod-

ules, and PCI cards in the Transport TX46.

2.2.1 Removing the chassis cover

Follow these instructions to remove the TX46 chassis cover.

1. Pull up the two retaining clips.

2. Lift off the cover.

3. The cover is removed.

2.2 Installing motherboard components

14 Chapter 2: Setting up

2.2.2 Installing CPUs

This section describes how to install AMD Opteron proces-

sors and heat sinks in your TX46 system.

NOTE: The system supports up to four CPUs. CPU0 must be

installed first followed by CPU 1, 2, and 3.

1. Remove the chassis cover as described in section 2.2.1

Removing the chassis cover.

2. Locate the processor sockets on the motherboard.

3. Lift the locking lever as shown.

CPU3

CPU1

CPU2

CPU0

Page is loading ...

Tyan B4881 User manual

This manual is also suitable for

Tyan B4881 User manual

Related papers

Other documents