Page is loading ...
INSTRUCTION MANUAL
Model Number: ACE-014
Car Entertainment System
WARNING:
This unit must be installed by
a professional technician only
or the warranty will be void.
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
ii
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
Remote Control
1 MODE: Press to select different input modes: Radio, Disc (if there is a
disc in the unit), USB (if there is a USB device in the unit), Bluetooth and
AV IN.
2 POWER: Power on or off.
3 RDM/BAND/C:
• In Radio mode, press to change radio band in sequence of FM1
FM2 FM3 AM1 AM2.
• In Disc mode, press to play randomly.
• In Bluetooth mode, press it to clear a single phone number.
4 / / / : Use to navigate through menu sesttings.
5 ENTER: Press to confirm selection or setting.
6 EJECT: Press to eject the disc.
7 *: In Bluetooth mode, press to enter a * symbol.
8 RPT/#/P.SCN/ :
• In SD/USB mode, press to REP 1 (repeat one track) REP DIR
(repeat directory) REP ALL (repeat all).
2
3
4
6
5
8
7
9
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26
20
1 27
iii
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
Remote Control (Cont.)
• In DVD mode, press to repeat REP OFF (repeat off) REP CH (repeat
chapter) REP TT (repeat title) REP A (repeat all).
• In Radio mode, PS (Preset Scan): Press to scan all preset stations in
the memory of the current band and stay on each memory station for
about 5 seconds.
• In radio mode, As (Auto Save): Long press to save the stations with
good reception automatically.
• In Bluetooth mode, press to enter a # symbol.
9 LOUD: Change loudness setting ON or OFF.
10 SEEK-:
• In DVD/USB mode, short press to skip to the previous track; press
and hold to fast reverse a track.
• In Radio mode, short press to skip to previously programmed preset
channels; press and hold to auto scan channels backwards.
11 PBC/STOP:
• In Disc mode, press ONCE to stop the disc playing; press the PLAY/
PAUSE button to resume playback from the last played location.
Press the button TWICE to stop playback completely.
• When watching VCD discs, press and hold for two seconds to set
PBC on/off.
12 OSD: In DVD mode, press to show on-screen menu options.
13 0-9 DIGITS:
• In Radio mode, select preset stations 1-6 on the desired band.
• In DVD mode, select a track.
• In Bluetooth mode, press to input a phone number; long press the 0
digit to enter a + symbol.
14 OPEN /TILT:
• Short press to open and close the TFT screen
• Press and hold to tilt the 7” screen at different angles.
15 VOL-: Press to decrease the volume level.
16 AUDIO:
• In Disc mode press to select the audio language.
• When watching VCDs, press it to select the sound track in the
sequence of MONO L MONO R STEREO.
17 SEL: Press to enter the SOUND SETTING menu.
iv
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
Remote Control (Cont.)
18 /SEEK+:
• In DVD/USB mode, short press to skip to the next track; press and
hold to fast forward a track.
• In Radio mode, short press to skip to next programmed preset
channels; press and hold to auto scan channels forwards.
• In Bluetooth mode, press to reject an incoming call or hang up after
answering a call.
19 VOL+: Press to increase the volume level.
20 ZOOM: Press and hold for two seconds in DVD mode to zoom the image
in or out in the sequence of ZOOM 2 ZOOM 3 ZOOM 4 ZOOM
1/2 ZOOM 1/3 ZOOM 1/4 ZOOM off.
21 ANGLE/ACCEPT:
• In DVD mode, press repeatedly to change the viewing angle (available
only with a recorded DVD file or DVD disc that supports this function).
• In Bluetooth mode, press to make a call after entering a phone
number or accept an incoming call.
22 REJECT: In Bluetooth mode, press to reject an incoming call or hang up
after answering a call.
23 SETUP: In DVD mode, press to enter the setup menu; press again to
resume playback.
24 HOME: Press to access the main on-screen display page.
25 SUBTITLE: Press to select the subtitle language (available only if the disc
supports subtitles).
26 MUTE /BLUETOOTH:
• Short press to mute the volume output; press again to restore volume.
• Long press to enter into Bluetooth mode.
27 PLAY/PAUSE: In DVD mode, press to pause playback; press again to
resume playback.
v
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
Remote control battery
The remote control comes with a CR2025 3V lithium button cell fully installed.
The battery should normally last for about one year, depending on frequency
of usage of the remote control.
• To use the remote control, pull out the plastic tab that separates the
battery from the contacts inside the compartment.
• If the remote control unit is no longer working even when it is operated
near the unit, you will need to replace the battery with a new battery of the
same type. Pull out the battery
tray and remove the old battery.
Insert a fresh CR2025 button
cell with the (+) marking facing
upwards. Then push the tray with
the battery back into the unit.
WARNING!
Keep batteries out of reach of children. Swallowing may
lead to serious injury or death in as little as 2 hours due
to internal burns. If swallowed, go straight to a hospital
emergency room. Dispose of used batteries immediately.
• If the remote is not used for an extended period of time, remove the
battery to prevent possible damage from battery leakage and corrosion.
• Do not attempt to short-circuit, disassemble or throw batteries into a fire.
• Dispose of batteries promptly and properly, observing any local
hazardous waste regulations. Do not burn or bury them.
Using the remote control
• Do not use the remote control while driving.
• Point the remote control directly towards the remote control sensor at
the front of the system. Make sure no obstacles are blocking its path.
The remote control will not operate if its path is blocked. The operating
distance may vary depending on the brightness of the ambient light.
• Handle the remote control with care. Do not drop, apply shock or step on
the remote control. Do not spill water on the unit.
• If you do not intend to use the remote control for an extended period of
time, remove the batteries to prevent possible leakage and corrosion.
Remote Control (Cont.)
1
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
Congratulations on choosing to buy a BAUHN
®
product.
All products brought to you by BAUHN
®
are manufactured to the highest
standards of performance and safety and, as part of our philosophy of
customer service and satisfaction, are backed by our comprehensive 1 Year
Warranty. We hope you will enjoy using your purchase for many years to
come.
Welcome
2
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
Remote Control ii
Welcome 1
Warranty Details 3
General Safety Instructions 4
Product Overview 7
Instructions 11
FAQs 20
Installation 22
Other Useful Information 27
Specifications 28
Repair and Refurbished Goods or Parts Notice 30
Contents
3
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
Warranty Details
The product is guaranteed to be free from defects in workmanship and parts
for a period of 12 months from the date of purchase. Defects that occur within
this warranty period, under normal use and care, will be repaired, replaced or
refunded at our discretion, solely at our option with no charge for parts and
labour. The benefits conferred by this warranty are in addition to all rights
and remedies in respect of the product that the consumer has under the
Competition and Consumer Act 2010 and similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and to compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure.
Car Entertainment System
4
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
General Safety Instructions
Read this manual thoroughly before first use and keep it in a safe place for
future reference, along with the warranty card, purchase receipt and carton.
The safety precautions enclosed herein reduce the risk of fire, electric shock
and injury when correctly adhered to. Follow all instructions and take notice
of all warnings to reduce the risk of fire or electric shock.
WARNING: This unit must be installed by a professional
technician only or the warranty will be void.
Driving safety — read before installation!
• Connection: To promote safety, certain functions are disabled unless the
parking brake is on. The system is designed to detect parked status and
must be connected to the power supply side of the parking brake switch.
Improper connection or use of this connection may violate applicable
laws and may result in serious injury or damage.
• Front video image display: To avoid the risk of accident and injury, and
the potential violation of applicable laws, never use the front video image
feature while the vehicle is being driven, unless the screen is used as a
driver aid such as for navigation or to view images from the rear view
camera when reversing or parking.
• DVD playback: Do not use this system with a video screen that is visible
to the driver, unless when using the rear view camera and navigation
system. DVD playback is disabled unless the vehicle is stationary and
the parking brake is engaged.
• Volume: Always keep the volume low enough so that you can hear
sounds from outside the vehicle.
• Location: Do not install the unit where operation of controls would
restrain driving safety.
• Usage restriction: The equipment is not intended for use by persons
(including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the equipment by a person
responsible for their safety.
• Children: Supervise young children to ensure they do not play with the
equipment.
• Liability: We accept no liability for any injury, damage or lost data caused
by noncompliance with these warnings or other improper use.
5
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
General Safety Instructions (Cont.)
WARNING: This unit must be installed by a professional
technician only or the warranty will be void.
Installation precautions
• Do not drill a hole into the engine compartment to connect the yellow cable
of the display unit to the vehicle battery. Engine vibration may eventually
cause the insulation to fail at the point where the wire passes from the
passenger compartment into the engine compartment. Take extra care in
securing the wire at this point.
• Make sure that cables will not interfere with moving parts of the vehicle,
such as the shift lever, parking brake or seat sliding mechanism.
• This unit cannot be installed in a vehicle without ACC (accessory) position
on the ignition switch.
• Use this unit with a 12V battery and negative grounding only. Failure to do
so may result in a fire or malfunction.
• To prevent a short circuit, overheating or malfunction, be sure to follow the
directions below:
* Disconnect the negative terminal of the battery before installation.
* Secure the wiring with cable clamps or adhesive tape. Wrap adhesive
tape around wiring that comes into contact with metal parts to protect
the wiring.
* Place all cables away from moving parts, such as the shift lever and seat
rails.
* Place all cables away from hot places, such as near the heater outlet.
* Do not connect the yellow cable to the battery by passing it through the
hole into the engine compartment.
* Cover any disconnected cable connectors with insulating tape.
* Do not shorten any cables.
* Never cut the insulation of the power cable of this unit in order to share
the power with other devices. The current capacity of the cable is
limited.
* Use a fuse of the rating prescribed.
* Never wire the negative speaker cable directly to ground.
* Never band together negative cables of multiple speakers.
6
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
General Safety Instructions (Cont.)
Operation precautions
• Operating conditions: Avoid installing the product in areas where it is
exposed to direct sunlight, high levels of dust, high temperatures (over
40°C) or high humidity (over 90%). In case of high temperatures, cool down
the car interior by means of ventilation or air-conditioning.
• Protect from moisture: Do not allow this unit to come in contact with
water or any liquids. Contact with liquids could result in electric shock and/
or damage to the unit.
• Ventilation: Operate the unit in well ventilated areas. Do not install the unit
where the cooling fan is blocked.
• Hot temperatures: Car parking under direct sunlight may increase the
temperature inside the car, which may affect the unit's ability to operate
properly. In such a case, reduce the temperature inside the vehicle and try
again after the temperature has returned to normal.
• Switchingon/o:Do not turn on or off the product in short intervals. When
turning the unit off, wait for at least 10 seconds prior to turning it on again.
• Playing discs: Do not operate the player with scratched, bent, broken or
irregular shaped discs. When a disc is not loaded properly, do not force it
into the player.
• Monitor position: If the back of the monitor touches the dashboard or air
conditioner inlet etc. after the monitor is opened, then adjust the TILT level
in the monitor TILT menu to prevent damage from repeated touching. If
the open monitor position is hindering remote control operation. In such a
case, make sure to use the remote control at a similar level of the remote
control receiver.
• Monitor operation: Do not open and close the monitor manually, it may
damage the monitor tilt system. Do not touch the LCD screen with hard
objects, which may damage or scratch the screen.
• Do not repair yourself: This unit does not contain any parts you can repair
yourself. Do not open it or attempt to repair or modify the unit. Opening
or removing covers may expose you to dangerous high voltage or other
hazards, and it will invalidate your warranty.
• Damage: If the unit has been damaged, have it serviced or repaired by
qualified personnel, contact the after sales support line for advice.
• Fuse: Do not replace the fuse on the power cable without professional
guidance. Using an inappropriate fuse may cause damage to the unit or
cause it to burn.
7
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
2
1
3
4
5 6 7 8 9 10 11
17 18 19
12
13
14
15
16
Faceplate
Product Overview
Front of the unit (behind the faceplate)
The buttons and controls are explained on the following pages.
20
8
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
Buttons and controls
1 DISC Slot
2 BAND/TILT Button:
• BAND: In Radio mode, press to change radio band in sequence of
FM1 FM2 FM3 AM1 AM2.
• TILT: Press and hold to tilt the screen.
3 MODE/GPS Button:
• Press to select different input modes: Radio, Disc (if there is a disc in
the unit), USB (if there is a USB device in the unit), Bluetooth and AV IN.
• Press and hold to select GPS mode.
4 SEL/MUTE Button:
• Short press to MUTE the sound; press it again to resume volume.
• Long press to enter the EQ Setup menu to adjust the sound settings:
CUSTOM ROCK POP JAZZ
CLASSIC
FLAT.
5 / PLAY/PAUSE Button: In Disc, USB, SD Card mode, press it to
pause, press it again to resume playback; long press to stop and press it
again to resume playback.
6 / Button:
• In Disc/USB mode, short press to skip to the previous track; press
and hold to fast reverse a track.
• In Radio mode, short press to skip to previously programmed preset
channels; press and hold to auto scan channels backwards.
• In Bluetooth mode, press to make a call after entering a phone
number or accept an incoming call.
7 / Button:
• In Disc/USB mode, short press to skip to the next track; press and
hold to fast forward a track.
• In Radio mode, short press to skip to next programmed preset
channels; press and hold to auto scan channels forwards.
• In Bluetooth mode, press to reject an incoming call or hang up after
answering a call.
Product Overview (Cont.)
9
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
Product Overview (Cont.)
8 VOL Knob / POWER Button:
• VOL Knob: Adjust the volume level by turning the knob clockwise to
increase or counterclockwise to decrease.
• POWER: Press it to turn the unit on or off.
9 LCD Display
10 Microphone
11 AV-IN Jack: Connect an external video device to the AV-IN jack.
12 RELEASE Button: Press to detach and release the front panel. When
released the unit will switch off automatically after a few seconds.
• Detach the panel: Press the REL button and pull out the left side to
detach the panel.
• Attach the panel: Insert the left side first and then press the right side
until you hear a clicking sound.
13 USB port (for multimedia playback only): Insert a USB device into this
port and the unit will automatically start reading and play back the files
(supported music file formats: MP3, WMA).
14 OPEN Button: Press to open and close the TFT monitor.
WARNING: Do not obstruct the monitor while in the opening or closing
cycle, this may cause damage to the monitor mechanism and is NOT
covered under warranty.
15 EJECT Button: Press to eject a disc. If the disc is not removed within
10 seconds after ejecting, the disc will reinsert automatically.
16 TFT Display
17 Anti-Theft LED Light
18 RESET Button: Press it with a thin, sharp object, the device will then be
reset to factory default settings.
19 SD/MMC Card Slot (for GPS and multimedia playback files only): Insert
the supplied SD card with GPS navigation software for use in GPS mode,
or an SD/MMC card with multimedia files, into this slot to play back the
card in SD/USB mode (supported music file formats: MP3, WMA).
20 IR signal receiver
10
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
Home screen
The Home screen is the root of the screen hierarchy. It displays when you
turn on the car entertainment system.
To display the Home screen during use, press the HOME button on the OSD
(on-screen display) or on the remote control.
The Home screen lets you browse installed Apps and configure the car
entertainment system's settings. Simply tap on the touch screen buttons to
access all features.
The Home screen options are:
• Disc – watch and listen to DVDs and CDs
• GPS – access the navigation software
• Radio – listen to FM and AM radio stations
• SD – media playback from your SD or MMC card, or insert the supplied
SD card with navigation software
• BT – pair your mobile phone using Bluetooth wireless technology and
make phone calls and listen to music
• USB – media playback from your USB drive
• AV IN – watch videos from an external video device
• Wallpaper – change the home screen wallpaper
• Calendar – access the calendar
• Setup – access the unit's setup menu options
• Calculator – access calculator
• Clock – access clock
• Tool – access other Apps such as games
Instructions
11
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
Instructions (Cont.)
NOTE!
• This unit will only display video if the vehicle is in parking position (the
hand brake is engaged). A warning message for driving safety displays if
the vehicle is moving.
• In Disc mode, the unit will also play picture and music files.
Disc mode controls
Disc mode
• To start watching and listening to discs, tap on DISC button. Inserting a
disc will begin automatic playback as well.
• Tap the TFT screen to display the on-screen playback control options.
Tap the screen again to hide the buttons.
STOP button.
Touch it to select the previous or next track.
PLAY/PAUSE button: In DVD mode, touch it to pause, touch
it again to start.
In DVD mode, touch it to enter the title menu (only available
with discs that support a title menu).
In DVD mode, touch it to choose Repeat Chapter Repeat
Title Repeat Off.
In DVD mode, touch it to choose Repeat 1 Repeat
Directory Repeat All.
Touch it to go to the next page menu.
In VCD mode, touch it to choose PBC ON or OFF.
Touch it to enter PGS mode.
12
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
GPS mode
• Make sure the SD card with GPS navigation software is inserted into the
SD card slot.
• Go to Home Setup GPS and click on the Folder Search icon to
automatically set the path to the GPS software. ACE-014 will warn you if
the SD card with navigation software is not present in the SD card slot.
• Tap on the GPS button to start the NDrive navigation software. The first
time you select GPS Navigation, a map of Canberra will be displayed on
the screen, until a GPS signal is obtained. After a few minutes, the GPS
will locate your current position and the map on the screen will change to
show your current location.
• Tap on the MENU button to access all GPS related options. You can
download the NDrive navigation software instruction manual from:
http://www.ndrive.com/sites/default/files/UG_V11_PND.pdf
Instructions (Cont.)
13
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
Radio mode
• Tap on the Radio button on the on-screen display to enter Radio mode.
Instructions (Cont.)
Touch it to enter the main menu.
Touch it to enter GPS mode.
Touch this button to enter the selected station.
Touch this button to search stations.
Touch this button to search stations.
Slide the icon to select stations.
Touch this button to choose FM1, FM2, AM1, AM2.
Touch this button to select LOC or DX stations.
Touch this button to scan the stations from 1-6.
Touch and hold this button to save the stations with good
reception automatically and scan each station for about 5
seconds.
Touch this button to enter the Sound setting.
NOTE: The default function is ST/MO when no radio signal
is received. As soon as a radio signal is received, the device
will automatically convert to ST (stereo) mode.
14
Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AUS
1300 886 649
NOTE!
• Always back up important data from your SD card or USB device
before playback on the equipment, as any wrong operation may cause
data loss or damage.
• We do not assume responsibility for any accidental data loss or
damage resulting from failure to back up files.
Instructions (Cont.)
SD/MMC/USB mode
• Insert an SD/MMC card or USB flash drive into the SD/MMC card slot or
USB port. Music playback will start automatically.
NOTE: Video playback is not supported.
• Do not remove the SD/MMC card or USB flash drive while in SD/MMC or
USB mode. Always remove the SD/MMC card or USB flash drive while in
Home screen or in another mode.
15
1300 886 649 Model: ACE-014 Product Code: 47499 11/2014
www.tempo.org
AFTER SALES SUPPORT
AUS
Instructions (Cont.)
Bluetooth
®
mode
WARNING!
Driving and having a telephone conversation at the same time is
dangerous. Please park your car before having a telephone conversation.
We assume no liability for any eventual injury or damage caused by
accidents due to noncompliance with this warning.
• Tap on the BT button to access all Bluetooth related functions. Or press
and hold the MUTE/BLUETOOTH button on the remote control.
• Tap the KEYPAD button to dial the number directly from the OSD.
• Tap the HISTORY button to check dialled, received and missed calls.
• Tap the PHONEBOOK button to use the phone book functions.
• Tap the MUSIC button to start the music player via Bluetooth technology.
Bluetooth pairing
• Tap on the BT button the Home screen to access Bluetooth functions.
• Tap on the CONNECT tab to enter pairing mode.
• On your mobile phone (or other Bluetooth enabled device), enable the
Bluetooth function, then search for new devices. (Please refer to the
instruction manual of your device for further instructions.)
• “ACE-014” should appear in the list on your mobile phone. Select “ACE-
014”. Some mobile phones require input of an identification code on initial
pairing. Enter the default password “1014”. When successfully paired, the
display will change from “Not Connect” to “Connected”.
• If pairing failed, try to pair again within several seconds. You can refer to
the operation instructions for your mobile phone, delete the device it was
searching for and pair again.
• To remove the pairing, tap the DISCON button or unpair from your device.
Auto-connect / Disconnect
• When the unit is powered on, the last paired phone will automatically be
connected to the device via Bluetooth. If the device cannot find the paired
phone after searching for about one minute, it will stop searching.
• When in Standby mode (unconnected), long press the BLUETOOTH
button on the remote control to activate the auto-connect function and
the device will search the last paired phone.
/
