Abus BW8010 Datasheet

Brand: Abus

Model: BW8010

Category: Motion detectors

Type: Datasheet

Abus BW8010 is a VdS-certified passive infrared motion sensor that detects heat movement and triggers an alarm when needed. Ideal for corner mounting, it offers a 90° aperture angle and a detection range of up to 15 x 15 meters, covering a whole room. With an alarm memory, it indicates which sensor was first triggered. Easily adjust its sensitivity with a jumper to define the number of pulses required to activate the alarm relay.

Abus BW8010 is a VdS-certified passive infrared motion sensor that detects heat movement and triggers an alarm when needed. Ideal for corner mounting, it offers a 90° aperture angle and a detection range of up to 15 x 15 meters, covering a whole room. With an alarm memory, it indicates which sensor was first triggered. Easily adjust its sensitivity with a jumper to define the number of pulses required to activate the alarm relay.

ABUS Security-Center

BW8010

Xevox Profi VdS motion detector

Product highlights:

• VdS-certified

• Alarm memory

• First-sensor recognition

• Detection range: 15 x 15m for complete room surveillance

• Aperture angle: 90°, ideal for corner mounting

The Xevox Profi VdS motion detector is a passive infrared motion

sensor (PIR sensor). It reacts to all types of heat movement and

reports this to the alarm centre.

The best place to install the equipment is in a corner, between 2 and

3 metres above the floor. The intruder’s possible direction of

movement should be at right-angles to the sensor. Unsuitable for

installation are all places opposite to sources of heat (e.g.: heating)

or a window. Do not install the motion sensor near to electric cables,

gas lines or electronic equipment that generates heat during long

periods of operation.

The viewing angle of the Xevox Profi VdS motion detector sensor is

90 degrees, and the detection range – depending on installation

height – up to 15 x 15 metres. You can vary the sensitivity of the

sensor with a jumper. In this way, you can define the number of

pulses that have to be detected before the sensor opens the alarm

relay.

The Xevox Profi VdS motion detector sensor has an alarm memory. If

the alarm centre is disarmed following an alarm, the LED on the

sensor that triggered the alarm lights up. Depending on the

configuration, you can also see which motion sensor first triggered

the alarm. Due to its reliability and high quality, the Xevox Profi VdS

motion detector sensor is VdS-certified.

© 2012 ABUS Security-Center GmbH & Co. KG, Errors and omissions excepted.

ABUS Security-Center

BW8010

Xevox Profi VdS motion detector

Technical Data

Installation Wall

Detection method PIR

Detection range (m) 15 x 15

Alarm memory Yes

Immune to animals No

Power consumption 11 mA

Voltage supply 12 V

Alarm contact NC, 50 mA, 24 V DC

Tamper contact NC, 100 mA, 24 V DC

Temperature range -10° to 55 °C

VdS G106505

VSÖ GS-N060614/01E

© 2012 ABUS Security-Center GmbH & Co. KG, Errors and omissions excepted.

1
2

Abus BW8010 Datasheet

Brand: Abus

Model: BW8010

Category: Motion detectors

Type: Datasheet

Abus BW8010 is a VdS-certified passive infrared motion sensor that detects heat movement and triggers an alarm when needed. Ideal for corner mounting, it offers a 90° aperture angle and a detection range of up to 15 x 15 meters, covering a whole room. With an alarm memory, it indicates which sensor was first triggered. Easily adjust its sensitivity with a jumper to define the number of pulses required to activate the alarm relay.

Related papers

Other documents