Guardian Technologies 508 User manual

Type 508

ISSUE 1

Downloaded from: http://www.guardianalarms.net

Introduction

Congratulations on choosing a Dennard Series 508 Camera Housing. This

operation manual provides information on the mounting variations, and access

to the Series 508 Camera Housings.

This operation manual will provide all the necessary information to install the

Series 508 Camera Housing.

Locking nut

Rotate 180°

The type 508 housing comes packed in the orientation shown in (fig.1)

To bring the 508 into operational service follow the following procedure.

1. Using the spanner (supplied) loosen the locking nut.

2. Rotate the extruded bracket arm and cast base through 180°

3. Retighten the locking nut, ensuring the extruded bracket arm is in the

desired position. (fig2)

The 508 housing is now ready to mount. (Refer to mounting Instructions

Section)

Fig.1

Fig.2

Method

Unpacking

508 operation manual Sheet. 1

A. 1 x Type 508 housing

B. 1 x Type 508 Handbook

C. 1 x 3mm A/F Allen Key

D. 1 x 4mm A/F Allen Key

E. 1 x 5mm A/F Allen Key

F. 1 x Spanner

G. 1 x Insulating Pad

H. 1 x Screw Insulator

I. 1 x 1/4” UNC x 3/8” Hex Hd. screw

J. 1 x M6 Plain Washer

K. 1 x M20 Cable Gland

List of contents

508 operation manual Sheet. 2

Before installation please remove the components from the packaging and

check that all items listed below have been supplied.

Component Spares

Heater - 240V

Heater - 110V

Heater - 24V

Heater - 12V

Thermostat

Window

Front Gasket

Rear Gasket

Fuse 1 Amp

Sealing Plug

Cable Gland

Gland Nut

Gland Washer

C590

C622

C623

C624

H12a

H146

A84

A85

C15

Z20

H66

H67

H66a

1

3

1

Description Ref.No. Quantity

508 operation manual Sheet. 3

Circuit Diagram

Unit fitted with a 20 x 5mm 1 Amp fuse as standard. It is the

customers responsibility to change the fuse to suit their own

application.

Cover

Earth

TB1

PLATFORM

FTB

FS1

L

E

N

Chassis

Earth

PCB1

PTC

Spare

508 operation manual Sheet. 4

To gain access to the 508 housing the following procedure should be fol-

lowed.

1. Remove the 6 off M5 x 20 soc. hd. screws from the back plate, using

the 4mm A/F long series ball allen key, these screws are held captive for

convenience.

2. Slide the body & sunsheild along the camera platform until it

becomes engaged on the hook.

3. Let the body & sunsheild hang from the hook. With the body hanging

from the hook any maintenance/ inspection of the camera and wiring

can be acheived in situ.

Replacing the body is the reverse procedure.

To remove the Body and sunsheild from the platform completely,

unscrew the 2 off M3 nuts from the suspension bracket whilst the body

is in the hanging position.

Operation

1.

2.

3.

Body

Suspension

Bracket

Platform

Hook

Body

Suspension

Bracket

Hook

Platform

View on Arrow ‘A’

Platform

Hook

Camera Platform

locates in the middle

slots only

Arrow

‘A

’

Body

508 operation manual Sheet. 5

Mounting Instructions

1.(2 x M6 x40 Soc. Cap hd screws)

4 x M6 x 16 Soc. Hd. Screws

Arrow ‘A’

View on arrow ‘A’

M20 Cable Gland

Wall

mounted configuration

3.

Ceiling

mounted configuration

2 x M6 Grub

Screws

Housing

body &

sunsheild

180°

Remove 4 x M6 x 16 Soc. Hd. screws from rear bracket and rotate cast

base until desired position of M20 cable gland is acheived. Replace M6

screws and tighten firmly.

to convert the housing from wall mounted to ceiling mounted orientation.

Remove 2 off fixings (item1), rotate bracket arm (item2) through 180° and

refit item 1. Loosen locking nut (item 3) & position the housing to the

desired orientation and re-lock.

For additional security 2 x M6 grub screws are provided. To gain access to

these grub screws, gently prise out the two plastic stop plugs. Then using

the 3mm A/F ball allen key (supplied) either one or both of the grub

screws can be tightened with the housing. in the desired orientation. To

re-orientate the hsg. at any time these grub screws must be loosened first.

2050 coax operation manual Sheet. 6

Outline Dimensions

SERIAL NO.

WARNING HOT

SURFACE AT

ALL TIMES

Specifications

Weight

Pan Movement

Tilt Movement

Heater Power

Heater Voltage

Weatherproofing Standard

4.0kg

+/- 90°

- 90°

9 Watts

240V

24V

110V

12V

BS.EN.60529 IP66

508 Camera Platform Outline

260 useable internal length

551

Poly-

carbonate

Window

10mm

Thick

Hidden Cable Bracket (Wall Mounted Orientation)

(-90° tilt down) (+/-90° Pan)

Customer

Cable Run

Locking

Nuts

91

175

Fused Mains Terminal Block and 6 way terminal block

Hidden Cable Bracket (Ceiling Mounted Orientation)

(-90° tilt down) (+/-90° Pan)

222

146

84 Max

+/-90° Pan

A

4 off mounting

holes Ø7.5

equi-spaced

on a 101.6

508 Housing Outline

One 3 Way Fused T.B.

One 6 Way T.B.

1 Slot Ø8.0

91

182

260 Useable Internal Length

332

PTC Heater

508 operation manual Sheet. 7

Customer Electrical Connections

6.

7.

9.

8.

1.

10.

4.

3.

2.

5.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

Platform

Gasket

Housing Back

Plate

423 Bracket

Assembly

Cable Run

Locking Nut

Rubber

Diaphragm

Housing Wiring Layout

Arrow ‘B’

Components

508 operation manual Sheet. 8

View on Rear T.B.’s

Arrow ‘B’

Customer Electrical Connections

Ref.

L

E

N

1

2

3

4

5

6

Function

Line

Earth

Neutral

Spare

1 to 6

L

E

N

From

Heater

Guardian Technologies 508, Security Camera 508, TYPE 508 User manual

Other documents