Verona VCLFSEE365E Installation guide

Verona
Brand
Verona
Model
VCLFSEE365E
Type
Installation guide
ELECTRIC RANGE
for residential use only
Models: VEFSEE 365 ..
USERS OPERATING INSTRUCTIONS
IMPORTANT - PLEASE READ AND FOLLOW
• Beforebeginning,pleasereadtheseinstructionscompletelyandcarefully.
• Donotremovepermanentlyafxedlabels,warnings,orplatesfromtheproduct.Thismay
voidthewarranty.
• Pleaseobservealllocalandnationalcodesandordinances.
• Pleaseensurethatthisproductisproperlygrounded.
• The installer should leave these instructions with the consumer who should retain
for local inspector’s use and for future reference.
ElectricalinstallationmustbeinaccordancewiththeNationalElectricalCode,ANSI/NFPA70
-latesteditionand/orlocalcodes.
IN CANADA: Electrical installation must be in accordance with the current CSA C22.1
CanadianElectricalCodesPart1and/orlocalcodes.
R
FOR INSTALLER ONLY
THIS RANGE IS FOR RESIDENTIAL USE ONLY
Some models are supplied with a protective lm on steel and aluminium
parts.Thislmmustberemovedbeforeinstalling/usingtheappliance.
INSTALLATION
2
3
WARNING !
Toreducetheriskoftippingtheappliance,
theappliancemustbesecuredbyproperly
installed anti-tip device packed with the
appliance.
• ALL RANGES CAN TIP
• INJURY TO PERSONS COULD RESULT
• INSTALL ANTI-TIP DEVICE PACKED
WITH RANGE
• SEE INSTALLATION INSTRUCTIONS
This appliance is designed and manufactured solely for the cooking of domestic (household)
foodandinnotsuitableforanynonedomesticapplicationandthereforeshouldnotbeusedina
commercialenvironmement.
Theappliancewarrantywillbevoidiftheapplianceisusedwithinanonedomesticenvironmement
i.e.asemicommercial,commercialorcommunalenvironment.
4
Screwdriver
Tape
measurePencil
Adjustable
pliers
Adjustable
wrench
Suitable protective
gloves Drill
Hammer
INSTALLATION INSTRUCTIONS
WARNING!
THIS APPLIANCE MUST BE INSTALLED BY A QUALIFIED INSTALLER.
Installation must conform with local codes.
Improperinstallation,adjustment,alteration,services,ormaintenancecancauseinjuryorpropertydamage.Consulta
qualiedinstalleroraserviceagent.
TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE)
IMPORTANT:Theuseofsuitableprotectiveclothing/glovesis
recommendedwhenhandling,installingofthisappliance.
5
GENERAL INFORMATION
1. WARNING!!
Thisapplianceshallnotbeusedforspaceheating.This
informationisbasedonsafetyconsiderations.
2. AlIopeningsinthewallbehindtheapplianceandintheoor
undertheapplianceshallbesealed.
3. Keep appliance area clear and free from combustible
materials,gasoline,andotherammablevapors.
4. Donotobstructtheowofventilationair.
5. Disconnect the electrical supply to the appliance before
servicing.
6. Whenremovingapplianceforcleaningand/orservice;
A. DisconnectACpowersupply.
B. Carefullyremovetherangebypullingoutward.
CAUTION:Rangeisheavy;usecareinhandling.
7. Electrical Requirement
Electrical installation should comply with national and local
codes.
8. Themisuseofovendoor(e.g.stepping,sitting,orleaningon
them)canresultinpotentialhazardsand/orinjuries.
9. Wheninstallingorremovingtherangeforservice,arollinglift
jackshouldbeused.Donotpushagainstanyoftheedgesof
therangeinanattempttoslideitintooroutoftheinstallation.
Pushingorpullingarange(ratherthanusingaliftjack)also
increases the possibility of bending the leg spindles or the
internalcouplingconnectors.
WARNING!!
ELECTRICAL GROUNDING INSTRUCTIONS
Therangemustbeelectricallygroundedinaccordancewith
localcodesor,intheabsenceoflocalcodes,withtheNational
Electrical Code,ANSI/NFPANo. 70-latest edition, inCanada
Canadian ElectricalCode.Installationshould be made bya
Iicensed electrician.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED.
If an external electrical source is utilized, the installation must
be electrically grounded in accordance with local codes or, in
the absence of local codes, with the national Electrical Code,
ANSI/NFPA70.
REPLACEMENT PARTS
Only authorized replacement parts may be used in performing
serviceontherange.Replacementpartsareavailablefromfactory
authorizedpartsdistributors.Contactthenearestpartsdistributor
inyourarea.
6
PROXIMITY TO SIDE CABINETS
1. This rangemay beinstalleddirectlyadjacentto existing36”
(914mm)highbasecabinets.
Rangedimensions:
• width:35”7/8(911mm)
• depth:23”31/32(609mm)
• height (without backguard / island trim): MIN 35” 7/16
(900mm)MAX37”13/32(950mm)
• backguard(height):8”(203mm)
• islandtrim(height):3”(76mm)
Groundedoutlet:shouldbelocated fromthe lefttotheright
sideofthe range;from6” 11/16(170mm) to8”21/32 (220
mm)[dependingonfeetregulation]fromthefloor.
Fig.1.1a
Fig.1.1b
2.TherangeCANNOTbeinstalleddirectlyadjacenttosidewalls,
tall cabinets, tall appliances, or other side vertical surfaces
above36”(914mm)high.
 Theremustbeaminimumof2”(50mm)sideclearancefrom
therangetosuchcombustiblesurfacesTOTHELEFTorTO
THERIGHTabovethe36”(914mm)highcountertop.
IMPORTANT:Oneside(leftorright)abovethe36”(914mm)
highcountertopmustalwaysbekeptclear.
 Installationwithislandtrim:Theremustbeaminimumof12”
(305mm)clearancefromthebackoftheislandtrimtosuch
combustiblesurfaceonthebackoftherangeabovethe36”
(914mm)highcountertop.
3.Themaximumuppercabinetdepthrecommendedis13”(330
mm).Wallcabinetabovetherangemustbeaminimumof30”
(762mm)abovethe countertop forawidth of minimum35”
7/8(911mm):ithastobecentredwiththerange.Sidewall
cabinetsabovetherangemustbeaminimumof18”(457mm)
abovethecountertop.
Backguard
Islandtrim
8"
(203 mm)
23"
31/32
(609 mm)
(911 mm)
35"
7/8
MIN 35" 7/16 (900 mm)
MAX 37"
13/32 (950 mm)
3"
(76 mm)
23"
31/32
(609 mm)
(911 mm)
35"
7/8
MIN 35" 7/16 (900 mm)
MAX 37"
13/32 (950 mm)
installation
1
7
Dottedlineshowingtheposition
oftherangewheninstalled
Areafor
ELECTRICAL
connection
6”11/16÷8”21/32(170÷220mm)
[dependingonfeetregulation]
Fig.1.2
ELECTRIC CONNECTION
1
8
Fig.1.3b
Fig.1.3a
PROXIMITY TO SIDE CABINETS
RANGE WITH BACKGUARD
(457 mm)
18" min.
30" min.
(762 mm)
(914 mm)
36"
0"
(0 mm)
0"
(0 mm)
20" min. (500 mm)
2" (50 mm)
13" max. (330 mm)
(457 mm)
18" min.
30" min.
(762 mm)
(914 mm)
36"
0"
0"
(0 mm)
(0 mm)
20" min. (500 mm)
2" (50 mm)
13" max. (330 mm)
OVEN VENT
OVEN VENT
1
9
Fig.1.3c
Fig.1.3d
PROXIMITY TO SIDE
CABINETS
RANGE WITH ISLAND TRIM
(457 mm)
18" min.
30" min.
(762 mm)
(914 mm)
36"
0"
0"
(0 mm)
(0 mm)
20" min. (500 mm)
13" max. (330 mm)
2" (50 mm)
12"
min. (305 mm)
(457 mm)
18" min.
30" min.
(762 mm)
(914 mm)
36"
0"
(0 mm)
0"
(0 mm)
20" min. (500 mm)
2" (50 mm)
13" max. (330 mm)
12"
min. (305 mm)
OVEN VENT
OVEN VENT
1
10
Fig.1.4
FITTING THE ADJUSTABLE FEET
Theadjustablefeetmustbefittedtothebaseofthecookerbeforeuse.
Resttherearofthecookeronapieceofthepolystyrenepackagingexposingthebase
forthefittingofthefeet.
ATTENTION:Mostimportant! Pay specialattentionnot to damagetherange during
this operation.
Fitthe4legsbyscrewingthemtightintothesupportbaseasshowninpicture1.5.
Fig.1.5
LEVELLING THE COOKER
ThecookermaybelevelledbyscrewingthelowerendsofthefeetINorOUT(fig.1.6).
Itisimportanttoobservethedirectionsoffigure1.6.
+ 1" 31/32
+ 50 mm
0 mm
0"
Fig.1.6
Fig.1.7a
Fig.1.7b
Fig.1.7c
MOVING THE COOKER
WARNING
When raising cooker to upright position always ensure two people carry out this
manoeuvretopreventdamagetotheadjustablefeet(fig.1.7a).
WARNING
Becareful:donotliftthecookerbythedoorhandlewhenraisingtotheuprightposition
(fig.1.7b).
WARNING
Whenmovingcookertoitsfinalposition
DO NOT DRAG
(fig.1.7c).
Liftfeetclearoffloor(fig.1.7a).
1
11
Fig.1.8
Fig.1.9
ASSEMBLING THE BACKGUARD
OR THE ISLAND TRIM
It is mandatory to install the backguard or
the island trim
• Assemble thebackguardorthe island trim
as shown in figure 1.8 or 1.9 and fix it
by screwing the 5 screws “
A
” (which are
alreadyfixedonthebackofthecooktop).
• Do not remove the 3 spacers “
B
” already
fittedonthebackofthebackguardorisland
trim.
A
A
B
B
A
A
B
B
1
12
26" 11/16 (678 mm)
from top of cooktop
with range installed
in final position
(455.5 mm)
17"
15/16
(455.5 mm)
17"
15/16
ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS
1. Theanti-tipbrackethastobeattachedasshownonfigurebelow,ithastobefixed
ontherearwallbyno.2(two)suitablescrews(suppliedwiththeanti-tipkit).
2. Afterfixingtheanti-tipbracket,sliderangeintoplace.Besuretheanti-tipbracketis
fullyinsertedintheslotoftherangeback.
Dottedlineshowingtheposition
oftherangewheninstalled
Slotforinserting
theanti-tipbracket
ANTI-TIPSTABILITY
DEVICEFIXING
Fig.1.10
Anti-tip
stabilitydevice
YOU MUST USE
STABILITY ANTI TIP
BRACKET TO PREVENT
UNIT FROM TIPPING.
1
13
ELECTRICAL REQUIREMENTS
• This appliancemustbe properlyinstalledand groundedbya qualifiedtechnicianin
accordancewiththeNational Electrical Code ANSI/NFPA No.70 (latestedition)and
local electrical code requirements. IN CANADA: Electrical installation must be in
accordancewiththecurrentCSAC22.1CanadianElectricalCodesPart1and/orlocal
codes.
• This appliance may beconnected bymeans ofpermanent “HardWiring” or“Power
SupplyCordKit”.Powersupplycord isnotsupplied,but itisavailablethroughyour
localelectricsupplyhouse.
• Useonly3-conductoror4-conductorCSA/ULlistedrangecordratedat50ampswith
250Vminimumandprovidedwithringterminals.Thesecordsshouldbeprovidedwith
strainrelieforconduitconnector.
Warning:Framegroundedthroughneutrallead.Ifusedin,
-Newbranch-circuitinstallations(1996NEC),
-Mobilehomes,
-Recreationalvehicles,or
-Inanareawherelocalcodesprohibitgroundingthroughneutral,usea4conductor
cordorconduit.
• Therangemustbeconnectedtotheproperelectricalvoltageandfrequencyasspeci-
fiedontheratingplate.
• Therangecanbeconnecteddirectlytothefuseddisconnect(orcircuitbreakerbox)
through flexible, armoured or non-metallic sheathed, copper cable (with grounding
wire).Allowtwotothreefeetofslackinthelinesothatitcanbemovedifservicingis
evernecessary.
VoltageandPowerConsumption
240-208/120V60Hz
11416W(240V)8575W(208V)
47.6A(240V)41.22A(208V)
ELECTRICAL CONNECTION WITH POWER CORD
Usea3-wirepowersupplycordkitratedfor50amps-125/250voltswithclosedloop
terminalsandmarkedforusewithranges.Wherelocalcodesdonotpermitgrounding
throughneutral,usea4-wirepowersupplycordkit.
Thecordmustbesecuredtotherangewithasuitablestrainrelief.Theelectricalcon-
nectionismadeattheterminalblock,whichislocatedbehindtheterminalblockaccess
plateonthebackoftherange.
ELECTRICAL CONNECTION WITH CONDUIT
Use3/4”tradesizeCSA/UL-listedconduitwithaconduitclamp,10AWG/600voltcopper
conductorcoloredredforline1andblackforline2and12AWG/600voltcopperconduc-
tor(or10AWG/600Voltcopperconductorifgroundingthroughneutral)coloredwhitefor
neutralwithclosedloopterminalsmarkedforusewithranges.
Wherelocalcodesdonotpermitgroundingthroughneutral,useagreen10AWGcopper
conductorasdirectedinthe4-wireconnectordirections.Theconduitmustbesecuredto
therangewiththestrainreliefbracket.Theelectricalconnectionismadeattheterminal
blockwhichislocatedbehindtheterminalblockaccessplateonthebackoftherange.
Location of
Nameplate
2
electrical connection
WARNING
TO AVOID ELECTRICAL SHOCK
HAZARD, BEFORE INSTALLING
THEAPPLIANCE, SWITCH POWER
OFF AT THE SERVICE PANEL AND
LOCK THE PANEL TO PREVENT
THE POWER FROM BEING
SWITCHED ON ACCIDENTALLY.
Electrical Shock Hazard
Electrically ground range.Failure to
follow these instruc-tions can result
indeath,re,orelectricalshock.
14
3-Wire Power Cord Installation
(SeeFigures3.1,3.2and3.3)
1. Removethe
Terminal Block Access Plate
onthebackofthe
rangebyunscrewingthe6fixing
Screws
(fig.3.1).
2. Insert the
Power Cord
through the hole in the
Power Cord
Bracket
; then tighten the
Power Cord
by using a suitable
Strain Relief
. Allow enough slack to easily attach the cord
terminalstothe
Terminal Block
.
3. Remove the 3 wire terminal nuts and washers from the
Terminal Block
.
4. Plugtheterminalholesof
Power Cord
.The
Neutral or Ground
Wire
of the
Power Cord
must be connected to the neutral
terminallocatedin the center of
Terminal Block
.The
Power
Wires
mustbeconnectedtotheoutsideterminals.
5. Plugwashersandtightennutssecurely.
Donotremove
Ground strap
.
6. Assemblethe
Terminal Block Access Plate
.
4-WirePowerCordInstallation
(SeeFigures3.1,3.2and3.4)
1. Removethe
Terminal Block Access Plate
onthebackofthe
rangebyunscrewingthe6fixing
Screws
(fig.3.1).
2. Insert the
Power Cord
through the hole in the
Power Cord
Bracket
; then tighten the
Power Cord
by using a suitable
Strain Relief
. Allow enough slack to easily attach the cord
terminalstothe
Terminal Block
.
3. Remove the 3 wire terminal nuts and washers from the
Terminal Block
.
4. Remove the
Ground Strap
from the frame of range and
terminal by removing its screw and cutting it as shown in
figure3.4.
5. Plugtheterminalholesof
Power Cord
.The
Neutral Wire
ofthe
Power Cord
mustbeconnectedtotheneutralterminallocated
in the center of
Terminal Block
; the
Power Wires
must be
connectedtotheoutsideterminals;the
Ground Wire
mustbe
attached to the frame of range by using the
(Ground)
identified
GroundingScrew
.
6. Plugwashersandtightennutssecurely.
7. Assemblethe
Terminal Block Access Plate
.
Terminal Block
Access Plate
Screws
Fig.3.1
Power Cord
Bracket
Hole D 1"
3/8
(34.93 mm)
Power Wires
Power Cord
Tighten the Power Cord
by using a suitable Strain Relief
Terminal Block
Ground strap
Neutral Wire
Power Wires
Power Cord
Tighten the Power Cord
by using a suitable Strain Relief
Terminal Block
Neutral Wire
Grounding Wire
Cut Ground Strap
Grounding
Screw
Fig.3.2
Fig.3.3
Fig.3.4
2
15
3-Wire Conduit Installation
(SeeFigures3.1,3.5and3.6)
1. Removethe
Terminal Block Access Plate
onthebackofthe
rangebyunscrewingthe6fixing
Screws
(fig.3.1).
2. Feed3/4”tradesize
Conduit
throughtheholeinthe
Conduit
Bracket
and secure to the
Conduit Bracket
with a
Conduit
Clamp
.
3. Remove the 3 wire terminal nuts and washers from the
Terminal Block
.
4. Plugtheterminalholesofconductors.The
Neutral or Ground
Wire
of the
Power Cord
must be connected to the neutral
terminallocatedin the center of
Terminal Block
.The
Power
Wires
mustbeconnectedtotheoutsideterminals.
5. Plugwashersandtightennutssecurely.
Donotremove
Ground strap
.
6. Assemblethe
Terminal Block Access Plate
.
4-WireConduitInstallation
(Seefigures3.1,3.5and3.7)
1. Removethe
Terminal Block Access Plate
onthebackofthe
rangebyunscrewingthe6fixing
Screws
(fig.3.1).
2. Feed3/4”tradesize
Conduit
throughtheholeinthe
Conduit
Bracket
and secure to the
Conduit Bracket
with a
Conduit
Clamp
.
3. Remove the 3 wire terminal nuts and washers from the
Terminal Block
.
4. Remove the
Ground Strap
from the frame of range and
terminal by removing its screw and cutting it as shown in
figure3.7.
5. Plug the terminal holes of conductors. The
Neutral Wire
of
the
Power Cord
must be connected to the neutral terminal
locatedinthecenterof
Terminal Block
;the
Power Wires
must
beconnectedtotheoutsideterminals;the
Ground Wire
must
beattached totheframeofrange byusingthe
(Ground)
identified
GroundingScrew
.
6. Plugwashersandtightennutssecurely.
7. Assemblethe
Terminal Block Access Plate
.
Hole D 1" 1/8
(28.58 mm)
Counduit
Bracket
Power Wires
Terminal Block
Ground strap
Neutral Wire
Conduit
Conduit Clamp
Power Wires
Terminal Block
Neutral Wire
Grounding Wire
Cut Ground Strap
Grounding
Screw
Conduit
Conduit Clamp
Fig.3.5
Fig.3.6
Fig.3.7
2
16
WIRING DIAGRAM
ELECTRIC DIAGRAM KEY
CF Cooling fan motor
TL1 Cooling fan thermal overload
AS Air switch
R Relay
M Terminal block
T Grounding point
OVEN
F1 Oven switch
TM Oven thermostat
PR Electronic programmer
TL Thermal overload
LF Oven lamp
S1 Oven temperature indicator light
C Top element
G Broil element
CIR Circular element
S Bottom element
V Fan motor
GLASS CERAMIC HOB
F2/3/5/6 Single zones energy regulators
F4 Double zone energy regulator
P1/2/4/5 Single zone radiant elements
P3 Double zone radiant element
CR Residual heat indicator lights
S3 Line pilot lamp
TL1
N/7
1
2
1a
2a
L/8
1
6
P1
P6
4
P4
3
8
P3
P8
2
7
P2
P7
5
P5
F1
C
CIR
S
G
V
LF
M
T
R
TL
CF
AS
TM
S1
PR
S3
F2
F3
F4
F5
P2P1
H
S
2
4
H
S
2
4
P4
H
S
2
4
P5
H
S
2
4
S1S2
4
Pilot
P1
P2
2
S1S2
4
Pilot
P1
P2
2
S1S2
4
Pilot
P1
P2
2
S1S2
4
Pilot
P1
P2
2
S1S2
4
4a
P1
P2
2
P3
4A
4
HS
2
F6
CR
ELECTRIC DIAGRAM KEY
CF Cooling fan motor
TL1 Cooling fan thermal overload
AS Air switch
R Relay
M Terminal block
T Grounding point
OVEN
F1 Oven switch
TM Oven thermostat
PR Electronic programmer
TL Thermal overload
LF Oven lamp
S1 Oven temperature indicator light
C Top element
G Broil element
CIR Circular element
S Bottom element
V Fan motor
GLASS CERAMIC HOB
F2/3/5/6 Single zones energy regulators
F4 Double zone energy regulator
P1/2/4/5 Single zone radiant elements
P3 Double zone radiant element
CR Residual heat indicator lights
S3 Line pilot lamp
2
17
18
19
Themanufacturercannotbeheldresponsibleforpossibleinaccuraciesduetoprintingortranscriptionerrors
inthepresentbooklet.
The manufacturer reserves the right to make all modications to its products deemed necessary for
manufacture or commercial reasons at any moment and without prior notice, without jeopardising the
essentialfunctionalandsafetycharacteristicsoftheappliances.
Cod.1104877-ß1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Verona VCLFSEE365E Installation guide

Verona
Brand
Verona
Model
VCLFSEE365E
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents