Simplicity 1693300 User manual

Brand: Simplicity

Model: 1693300

Category: Lawnmowers

Type: User manual

This manual is also suitable for

How to use this file...(Operators Manuals)

————————————————————————————————————————————–––

Instructions for

Print Vendors (Paper Manuals)

Paper Size: * 11 x 17

* Body—50 lbs brilliant white offset or equivalent.

* Cover—on pre-printed two-tone “Swash” stock.

Press: * Body—1-color, 2-sided

* Cover imprint —1-color, 1-sided

Bindery: * Saddle Stitch, Face Trim, 3-Hole Drill

* Face Trim

COVERS: * This file contains several manuals, which differ only in their covers.

* Covers are all present at the beginning of this file.

* Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover.

• Check the front cover for the individual part number (typically a 171xxxx number).

BODY: • The body of the manual is identical, regardless of the cover used.

* REMEMBER: ODD number pages are ALWAYS right hand pages, and EVEN number are ALWAYS

left hand pages.

General: * This instruction page is NOT part of the manual and must NOT be printed.

• Pages labeled with the text “THIS PAGE INTENTIONALLY BLANK” are placement pages ONLY,

and should NOT be printed.

————————————————————————————————————————————–––

If you have further questions on how to utilize this file, please contact

Simplicity Technical Publications Department at (414) 284-8650.

THIS PAGE INTENTIONALLY BLANK

OPERATOR’S

MANUAL

ZT Series

14HP Riders

Mfg. No. Description

1693286 Zero Turn, 14HP Hydro

1693290 Zero Turn, 14HP Hydro (Export)

16HP Riders

Mfg. No. Description

1693288 Zero Turn, 16HP Hydro

1693292 Zero Turn, 16HP Hydro (Export)

38” Mower Decks

Mfg. No. Description

1692912 38” Mower Deck

44” Mower Decks

Mfg. No. Description

1692914 44” Mower Deck

1719191-00

Rev 4/1998

TP 100-2165-00-ZT-SMA

MANUFACTURING, INC.

500 N Spring Street / PO Box 997

Port Washington, WI 53074-0997

www.simplicitymfg.com

OPERATOR’S

MANUAL

ZT Series

14HP Riders

Mfg. No. Description

1693296 Zero Turn, 14HP Hydro

16HP Riders

Mfg. No. Description

1693298 Zero Turn, 16HP Hydro

38” Mower Decks

Mfg. No. Description

1692913 38” Mower Deck

44” Mower Decks

Mfg. No. Description

1692915 44” Mower Deck

1719192-00

Rev 4/1998

TP 100-2165-00-ZT-SMA

AGCO-Allis Lawn & Garden Equipment

500 N. Spring Street \ P.O. Box 997

Port Washington, WI 53074-0997 USA

www.allislawn.com

OPERATOR’S

MANUAL

ZT Series

14HP Riders

Mfg. No. Description

1693300 Zero Turn, 14HP Hydro

16HP Riders

Mfg. No. Description

1693302 Zero Turn, 16HP Hydro

38” Mower Decks

Mfg. No. Description

1692913 38” Mower Deck

44” Mower Decks

Mfg. No. Description

1692915 44” Mower Deck

1719193-00

Rev 4/1998

TP 100-2165-00-ZT-SMA

Massey Ferguson Lawn & Garden Equipment

is Manufactured and Distributed by Simplicity Manufacturing, Inc.

500 N. Spring Street • P.O. Box 997

•

Port Washington, WI 53074-0997 USA

www.masseylawn.com

Troubleshooting, Adjustments & Service.......19

Troubleshooting the Rider.....................................19

Troubleshooting the Mower ..................................20

Seat Adjustment....................................................21

Top Speed Adjustment .........................................21

Brake Adjustment..................................................21

Mower Adjustments ..............................................22

Blade Brake Check ...............................................23

Mower Belt Replacement......................................23

Rider Drive Belt Replacement...............................24

Battery Service......................................................25

Checking the Battery Voltage ...........................25

Charging A Completely

Discharged Battery .......................................25

Jump Starting with

Auxiliary (Booster) Battery ............................25

Specifications....................................................27

Parts & Accessories..........................................28

Lawn Care & Mowing Information.............LC—1

International Symbols ................................LC—8

Technical Manuals ......................................LC—8

NOTE: In this manual, “left” and “right” are referred to as

seen from the operating position.

Identification Numbers .......................................2

Safety Rules & Information ................................3

Features & Controls............................................6

Control Functions....................................................6

Safety Interlock System ..........................................7

Operating the Zero Turn Rider ...........................8

General ...................................................................8

Checks Before Starting...........................................8

Starting The Engine ................................................9

Stopping the Rider ..................................................9

Pushing the Rider by Hand ....................................9

Zero Turn Driving Practice....................................10

Mower Installation & Removal ..............................12

Adjusting Mower Cutting Height............................12

Storage .................................................................13

Regular Maintenance ........................................14

Maintenance Schedule .........................................14

Checking Tire Pressures.......................................14

Checking/Adding Fuel...........................................15

Fuel Filter..............................................................15

Oil & Filter Change................................................15

Check / Change Air FIlter......................................15

Replace Spark Plug ..............................................15

Check Transmission Oil Level ..............................15

Lubrication ............................................................16

Battery Maintenance.............................................17

Checking Battery Fluid..................................17

Cleaning the Battery and Cables ..................17

Servicing the Mower Blades .................................18

Table of Contents

TP 100-2165-00-AT-SMA

WARNING

Engine exhaust from this product contains

chemicals known, in certain quantities, to cause

cancer, birth defects, or other reproductive harm.

169XXXX

MFG

Simplicity Manufacturing, Inc.

Port Washington, WI 53074-0997 U.S.A.

SERIAL

XXXXX

Mower Deck

Identification Tag

Unit

Identification Tag

SSAAMMPPLLEE

When contacting your Authorized

Dealer for replacement parts, service,

or information YOU MUST HAVE

THESE NUMBERS.

Identification

Numbers

IDENTIFICATION NUMBERS

Record your model name/number, unit and mower deck

manufacturer numbers and engine serial number in the

space provided for easy reference.

• The Unit I.D. tag is located on the left-side, of the

frame, as shown below.

• The Mower Deck I.D. tag is also on the left side, on

top of the mower deck.

• For location of Engine Serial Number, refer to the

Engine Owner’s Manual.

Be sure to fill out and return the Warranty Registration

Card supplied with your unit.

IDENTIFICATION TAG LOCATIONS

ENGINE REFERENCE DATA

Model Description Name/Number

Unit MFG

Number

PRODUCT REFERENCE DATA

Unit SERIAL Number

Dealer Name

Date Purchased

Engine Make

Engine Type/Spec

Engine Model

Engine Code/Serial Number

Mower Deck MFG Number

Mower Deck SERIAL

Number

Safety Rules

& Information

GENERAL OPERATION

• Read, understand, and follow all instructions in the

manual and on the unit before starting.

• Only allow responsible adults, who are familiar with

the instructions, to operate the unit.

• Clear the area of objects such as rocks, toys, wire,

etc., which could be picked up and thrown by the

blade(s).

• Be sure the area is clear of other people before mow-

ing. Stop unit if anyone enters the area.

• Never carry passengers.

• Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while trav-

elling in reverse.

• Be aware of the mower discharge direction and do

not point it at anyone. Do not operate the mower

without either the entire grass catcher or the deflector

in place.

• Slow down before turning.

• Never leave a running unit unattended. Always

disengage the PTO, set parking brake, stop engine,

and remove keys before dismounting.

• Turn off the PTO switch to disengage the blades

when not mowing.

• Stop engine before removing grass catcher or

unclogging chute.

• Mow only in daylight or good artificial light.

• Do not operate the unit while under the influence of

alcohol or drugs.

• Watch for traffic when operating near or crossing

roadways.

• Use extra care when loading or unloading the unit

into a trailer or truck.

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and

tip-over accidents, which can result in severe injury or

death. All slopes require extra caution. If you cannot

back up the slope or if you feel uneasy on it, do not

drive on it.

• Mow up and down slopes, not across.

• Remove obstacles such as rocks, tree limbs, etc.

• Watch for holes, ruts, or bumps. Uneven terrain could

overturn the unit. Tall grass can hide obstacles.

• Use slow speed. Choose a low gear so that you will

not have to stop or shift while on the slope.

• Use extra care with grass catchers or other attach-

ments. These can change the stability of the unit.

• Keep all movement on the slopes slow and gradual.

Do not make sudden changes in speed or direction.

Do Not

•

Do not

start or stop on a slope. If tires lose traction,

disengage the blade(s) and proceed slowly straight

down the slope.

•

Do not

turn on slopes unless necessary, and then,

turn slowly and gradually uphill, if possible.

•

Do not

mow near drop-offs, ditches, or embank-

ments. The mower could suddenly turn over if a

wheel is over the edge of a cliff or ditch, or if an edge

caves in.

•

Do not

mow on wet grass. Reduced traction could

cause sliding.

•

Do not

try to stabilize the unit by putting your foot on

the ground.

•

Do not

use grass catcher on steep slopes.

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of

unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mow-

ing deck is capable of amputating hands and feet and throwing objects. The triangle in text signi-

fies important cautions or warnings which must be followed.

WARNING

Never operate on slopes greater than 30 percent

(16.7°) which is a rise of three feet vertically in 10

feet horizontally.

Select slow ground speed before driving onto slope.

Use extra caution when operating on slopes with

rear-mounted grass catcher.

Mow UP and DOWN the slope, never across the

face, use caution when changing directions and

DO NOT START OR STOP ON SLOPE.

Safety Rules & Information

CHILDREN

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted to

the unit and the mowing activity. Never assume that chil-

dren will remain where you last saw them.

• Keep children out of the mowing area and under the

watchful care of another responsible adult.

• Be alert and turn unit off if children enter the area.

• Before and during reverse operation, look behind and

down for small children.

• Never carry children. They may fall off and be seri-

ously injured or interfere with safe unit operation.

• Never allow children to operate the unit.

•

Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

TRANSPORTING AND STORAGE

• Always observe safe refueling and fuel handling prac-

tices when refueling the unit after transportation or

storage.

• Always follow the engine manual instructions for

storage preparations before storing the unit for both

short and long term periods.

• Always follow the engine manual instructions for

proper start-up procedures when returning the unit to

service.

• Never store the unit or fuel container inside where

there is an open flame or pilot light, such as in a

water heater. Allow unit to cool before storing.

SERVICE AND MAINTENANCE

• Use extra care in handling gasoline and other fuels.

They are flammable and vapors are explosive.

a) Use only an approved container.

b) Never remove gas cap or add fuel with the engine

running. Allow engine to cool before refueling. Do

not smoke.

c) Never refuel the unit indoors.

• Never run a unit in an enclosed area.

• Keep nuts and bolts, especially blade attachment

bolts, tight and keep equipment in good condition.

• Never tamper with safety devices. Check their proper

operation regularly.

• Keep unit free of grass, leaves, or other debris build-

up. Clean up oil or fuel spillage.

• Stop and inspect the equipment if you strike an

object. Repair, if necessary, before restarting.

• Never make adjustments or repairs with the engine

running unless specified otherwise in the engine

manufacturer’s manual.

• Grass catcher components are subject to wear, dam-

age, and deterioration, which could expose moving

parts or allow objects to be thrown. Frequently check

components and replace with manufacturer’s recom-

mended parts, when necessary.

• Mower blades are sharp and can cut. Wrap the

blade(s) or wear gloves, and use extra caution when

servicing them.

• Check brake operation frequently. Adjust and service

as required.

• Use only factory authorized replacement parts when

making repairs.

• Always comply with factory specifications on all

settings and adjustments.

• Only authorized service locations should be utilized

for major service and repair requirements.

• Never attempt to make major repairs on this unit

unless you have been properly trained. Improper ser-

vice procedures can result in hazardous operation,

equipment damage and voiding of manufacturer’s

warranty.

WARNING

Never place hands near the hydro pump cooling

fan when the unit is running. Cooling fan is

located on top of transaxle.

Safety Rules & Information

SAFETY DECALS

This unit has been designed and manufactured to pro-

vide you with the safety and reliability you would expect

from an industry leader in outdoor power equipment

manufacturing.

Although reading this manual and the safety instructions

it contains will provide you with the necessary basic

knowledge to operate this equipment safely and effec-

tively, we have placed several safety labels on the unit to

remind you of this important information while you are

operating your unit.

All DANGER, WARNING, CAUTION and instructional

messages on your rider and mower should be carefully

read and obeyed. Personal bodily injury can result when

these instructions are not followed. The information is for

your safety and it is important! The safety decals below

are on your rider and mower.

If any of these decals are lost or damaged, replace them

at once. See your local dealer for replacements.

These labels are easily applied and will act as a constant

visual reminder to you, and others who may use the

equipment, to follow the safety instructions necessary for

safe, effective operation.

DANGER

ROTATING CUTTING BLADE

Do not put hands or feet

under mower deck while

blade is rotating.

1704276

DANGER

ROTATING CUTTING BLADE

Do not operate mower

without deflector or entire

grass catcher in place.

1704277

Decal - Danger

Part No. 1704276

Decal - Danger

Part No. 1704277

AVOID SERIOUS INJURY OR DEATH

• READ OPERATOR'S MANUAL(S).

• KNOW LOCATION AND FUNCTION OF ALL CONTROLS.

• KEEP SAFETY DEVICES (GUARDS, SHIELDS, &

SWITCHES) IN PLACE AND WORKING.

• REMOVE OBJECTS THAT COULD BE THROWN BY

THE BLADE.

• DO NOT MOW WHEN CHILDREN OR OTHERS

ARE AROUND.

• NEVER CARRY CHILDREN.

• LOOK DOWN AND BEHIND—BEFORE AND WHILE

BACKING.

• AVOID SUDDEN TURNS.

• IF YOU CANNOT BACK UP A HILL

— DO NOT OPERATE ON IT.

• GO UP AND DOWN SLOPES, NOT ACROSS.

• IF MACHINE STOPS GOING UPHILL, STOP BLADE

AND BACK DOWN SLOWLY.

• BE SURE BLADE(S) AND ENGINE ARE STOPPED

BEFORE PLACING HANDS OR FEET NEAR BLADE(S).

• WHEN LEAVING MACHINE, SHUT OFF ENGINE,

REMOVE KEY, AND SET PARKING BRAKE.

WARNING

DO NOT TOW UNIT!

Damage may result to

drive mechanism.

OPERATION

To Start Engine

• Seat must be occupied.

• Clutch/Brake pedal must

be depressed.

• PTO switch must be off.

Ignition Switch

OFF

RUN

START

Clutch/Brake

Pedal

Parking

Brake

Knob

Parking Brake

To Set Parking Brake

• Pull knob up while Clutch/Brake

pedal is depressed.

• Release Clutch/Brake pedal

while holding knob.

To Release Parking Brake

• Depress Clutch/Brake pedal.

• Push knob down while

Clutch/Brake pedal is depressed.

To Adjust Top Speed of Wheels

COLUMN KNOBS INDEPENDENTLY

CONTROL TOP SPEED OF

EACH WHEEL

• Turn knob clockwise to lower

top speed of a wheel.

• Turn knob counter-clockwise to

raise top speed of a wheel.

Lower speed of faster wheel until

vehicle travels in straight line when

both levers are in the MAXIMUM

forward position.

When Operator Leaves Seat

• Engine will shut off if Parking Brake is

not engaged.

• Engine will shut off if PTO switch is on.

PTO Switch

To Operate PTO clutch

• The operator must be in seat.

• To engage PTO, pull switch up.

• To disengage PTO, push switch down.

ROTATING BLADES

CUT OFF ARMS

AND LEGS

STOP MOWER WHEN

CHILDREN ARE NEAR.

NO RIDERS

— THEY FALL OFF.

DANGER

OPERATING ON

SLOPES CAN BE

DANGEROUS

SEE OPERATOR'S

MANUAL.

IF YOU CANNOT

BACK-UP A HILL

—DO NOT DRIVE ON IT.

1715993

Decal - Operating Instructions

Part No. 1715993

Features & Controls

of the Zero Turn Rider

Figure 1. Rider & Mower Controls (Seen from Operator’s Position)

A. Ground Speed Control Levers

These levers control the ground speed of the rider. The

left lever controls the left rear drive wheel and the right

controls the right rear drive wheel.

Moving a lever forward increases the FORWARD speed

of the associated wheel, and pulling back on a lever

increases the REVERSE speed.

Note: The further a lever is moved away from the neutral

position the faster the drive wheel will turn.

B. Top Speed Adjustment Knobs

These knobs independently control the top speed of the

left and right drive wheels, and are used to balance the

maximum forward lever positions. Turn a knob CLOCK-

WISE to lower the top speed of a wheel, and COUNTER-

CLOCKWISE to increase the top speed of a wheel.

C. Seat Adjustment Lever

The seat can be adjusted forward and back. Move the

lever to the LEFT, position the seat as desired, and

release the lever to lock the seat in position.

A. Ground Speed Control Levers

B. Top Speed Adjustment Knobs

C. Seat Adjustment Lever

D. Ignition Switch

E. Parking Brake Knob

F. Clutch/Brake Pedal

G. PTO (Electric Clutch) Switch

H. Throttle/Choke Control

I. Mower Height Adjuster

Please take a moment and

familiarize yourself with the

name, location, and function of

these controls so that you will

better understand the safety and

operating instructions provided in

this manual.

CONTROL FUNCTIONS

The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing

require the combined use of several controls applied in specific sequences. To learn what combination and sequence

of controls to use for various tasks see the OPERATION section.

Control Functions continued…

D. Ignition Switch

The ignition switch starts and stops the engine, it has

three positions:

OFF Stops the engine and shuts off the

electrical system.

RUN Allows the engine to run and powers the

electrical system.

START Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN posi-

tion with the engine stopped–this drains the battery.

E. Parking Brake Knob

The parking brake is applied by fully depressing the

clutch/brake pedal (F, Figure 1), and then pulling UP on

the parking brake knob (E, Figure 1). To release the

parking brake, fully depress the clutch/brake pedal, and

push the knob DOWN.

F. Clutch/Brake Pedal

Depressing the clutch/brake pedal disengages the trans-

missions and applies the brake.

G. PTO (Power Take Off) Switch

The PTO switch engages and disengages the mower.

Pull OUT on the switch to engage, and push IN to disen-

gage.

H. Mower Height Adjuster

This controls the cutting height of the mower deck.

Moving this lever to the LEFT and then into the desired

cutting height position. Moving the lever FORWARD

decreases the cutting height, and BACK increases the

cutting height.

I. Throttle / Choke Control

The throttle controls engine speed. Move the throttle for-

ward to increase the engine speed and back to decrease

engine speed. Moving the throttle / choke control fully

forward chokes the engine for cold starts. (A warm

engine may not require choking.) Always operate the unit

at FULL throttle.

Features & Controls

SAFETY

INTERLOCK SYSTEM

This unit is equipped with safety interlock switches

and other safety devices. These safety systems are

present for your safety, do not attempt to bypass

safety switches, and never tamper with safety

devices. Check their operation regularly.

Operational SAFETY Checks

Your unit is equipped with a seat switch safety sys-

tem. Check the seat switch operation every fall and

spring with the following tests.

Test 1 — Engine should NOT crank if any of the

following conditions exist:

• PTO switch is engaged (ON), OR

• Clutch/brake pedal is NOT fully depressed.

Test 2 — Engine SHOULD crank if ALL of the

following conditions are met:

• PTO switch is NOT engaged, AND

• Clutch/brake pedal IS fully depressed.

Test 3 — Engine should SHUT OFF if any of the

following conditions exist:

• Operator rises off seat with transmission control

levers out of the neutral gate AND clutch/brake

pedal NOT depressed, OR

• Operator rises off seat with clutch/brake pedal

NOT fully depressed, OR

• Operator rises off seat with PTO engaged.

Test 4 — Blade Brake Check

Mower blades and mower drive belt should come to

a complete stop within five seconds after electric

PTO switch is turned off (or operator rises off seat).

If mower drive belt does not stop within five sec-

onds, see your dealer.

NOTE: Once the engine has stopped, PTO switch

must be turned off after operator returns to the seat

in order to start the engine.

WARNING

If the unit does not pass a safety test, do not

operate it. See your authorized dealer. Under

no circumstance should you attempt to

defeat the purpose of the safety interlock

system.

GENERAL OPERATING SAFETY

Before first time operation:

• Be sure to read all information in the Safety and

Operation sections before attempting to operate this

rider and mower.

• Become familiar with all of the controls and how to

stop the unit.

• Drive in an open area without mowing to become

accustomed to the unit.

CHECKS BEFORE STARTING

• Check that crankcase is filled to full mark on dipstick.

See the engine Operator’s Manual for instructions

and oil recommendations.

• Make sure all nuts, bolts, screws and pins are in

place and tight.

• Adjust the seat position, and make certain you can

reach all controls from operator’s position.

Operating

the Zero Turn Rider

DANGER

OPERATING ON SLOPES

CAN BE DANGEROUS

Never operate on slopes greater than 30 percent

(16.7°) which is a rise of three feet vertically in 10

feet horizontally.

Operate the rider at a slow ground speed when

driving onto slope.

This unit is equipped with standard rear

counterweights - DO NOT OPERATE THE UNIT

WITHOUT THESE COUNTERWEIGHT IN PLACE.

In addition to counterweights, use extra caution

when operating on slopes with rear-mounted

grass catcher. Mow UP and DOWN the slope,

never across the face, use caution when

changing directions and DO NOT START OR

STOP ON SLOPE.

WARNING

Never allow passengers to ride on the unit.

Before leaving the operator’s position for any

reason, engage the parking brake, disengage the

PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, rider and

mower free of grass, leaves and excess grease.

Do not stop or park rider over dry leaves, grass or

combustible materials.

Gasoline is highly flammable and must be

handled with care. Never fill the tank when the

engine is still hot from recent operation. Do not

allow open flame, smoking or matches in the

area. Avoid over-filling and wipe up any spills.

Figure 2. Engine Access & Rear Weights

A. Fuel Tank

B. Rear Counterweights

Lift Deck

to access

Engine

• Fill the gasoline tank with fresh gasoline. Refer to

engine manual for gasoline recommendations.

• Make certain rear counterweights (see Figure 2) are

installed at all times, and use extra caution if you will

be operating the unit on sloping ground.

Operating the Zero Turn Rider

Figure 3. Rider & Mower Controls (Operator’s Position)

A. Ground Speed Control Levers

B. Top Speed Adjustment Knobs

C. Seat Adjustment Lever

D. Ignition Switch

E. Parking Brake Knob

F. Clutch/Brake Pedal

G. PTO (Electric Clutch) Switch

H. Throttle/Choke Control

I. Mower Height Adjuster

Figure 4. Hydro Transmission Release Levers

A. Left Lever (shown in DRIVE position)

B. Right Lever (shown in PUSH position)

DO NOT TOW RIDER

Towing the unit will cause transmission

damage. Do not use another vehicle to

push or pull this unit.

STARTING THE ENGINE

1. While sitting in the operator seat, and fully depress

the clutch/brake pedal or set the parking brake.

2. Set engine throttle control (H, Figure 3) all the way up

to CHOKE. A warm engine may not require choking.

3. Disengage the PTO by pushing the PTO switch all

the way down (G, Figure 3)

4. Insert the key into the ignition switch (D, Figure 3)

and turn it to START.

5. After the engine starts, move the engine throttle con-

trol (H, Figure 3) to SLOW. Warm up the engine by

running it for at least a minute before engaging the

PTO switch or driving the rider.

6. After warming up the engine, ALWAYS operate

the unit at FULL THROTTLE when mowing.

In the event of an emergency the engine can be

stopped by simply turning the ignition switch to

STOP. Use this method only in emergency situations.

For normal engine shut down follow the procedure given

in STOPPING THE RIDER.

STOPPING THE RIDER

1. Returning the ground speed control levers (A, Figure 3)

to the middle positions will stop rider movement. For

emergency stopping depress the clutch/brake

pedal (see F, Figure 3).

2. Disengage the PTO by pushing down on the PTO

switch (See G, Figure 3).

3. Set engine throttle control (H, Figure 3) to mid-throttle

position and turn the ignition key to OFF. Remove

the key.

NOTE: Stopping the engine at any speed other than mid-

throttle can cause engine damage. Do NOT stop the

engine with the throttle control in the IDLE position.

PUSHING THE RIDER BY HAND

1. Disengage the PTO, engage the parking brake, turn

the ignition OFF, and remove the key.

2. Disengage the transmissions by moving both release

levers from engaged position(A, Figure 4) to released

position (B). The release levers are located in the

back of the unit between the rear weights (see Figure

4). BOTH release levers must be pulled fully rear-

ward and down to push the rider by hand.

NOTE: To drive the rider BOTH release levers must be

moved completely forward to engage the transmissions.

Operating the Zero Turn Rider

ZERO TURN

DRIVING PRACTICE

The lever controls of the Zero Turn rider are

responsive

and learning to gain a

smooth

and

efficient

control of the

rider’s forward, reverse, and turning movements will take

some practice.

Spending some time going through the maneuvers

shown and becoming familiar with how the unit acceler-

ates, travels, and steers — before you begin mowing —

is absolutely essential to getting the most out of the Zero

Turn rider.

Locate a smooth, flat area of your lawn — one with

plenty of room to maneuver. (Clear the area of objects,

people and animals before you begin.) Operate the unit

at mid-throttle during this practice session (ALWAYS

operate at full throttle when mowing), and turn slowly to

prevent tire slippage and damage to your lawn.

We suggest you begin with the Smooth Travel proce-

dure to the right, and then advance through the forward,

reverse, and turning maneuvers.

Smooth Travel

The lever controls of the

Zero Turn rider are

RESPONSIVE

The BEST method of

handling the ground

speed control levers is in

three steps — as shown

in Figure 5.

FIRST place the palms of

your hands onto the

levers as shown.

SECOND, to go forward

gradually push the levers

toward the console with

your palms.

THIRD, to speed up

move the levers farther

forward. To slow down

smoothly, loosen your

grip on the console and

allow the levers to return

toward neutral.

Figure 6. Forward Travel

Figure 7. Reverse Travel

Figure 5. Move Control

Levers Gradually.

Forward Travel Practice

Gradually move both ground speed control levers —

evenly FORWARD from neutral. Slow down and repeat.

NOTE: Straight forward travel takes practice. If neces-

sary, top speed can be balance-adjusted — see the Top

Speed Adjustment Knobs in the Adjustments section

near the back of this manual.

Reverse Travel Practice

LOOK DOWN & BEHIND, then gradually move both

ground speed control levers evenly BACK from neutral.

Slow down and repeat.

NOTE: Practice backing up for several minutes before

attempting to do so near objects. The rider turns sharply

in reverse as well as forward, and backing up straight

takes practice.

WARNING

Make certain the area of operation, and especially

the direction of travel is clear of objects, people

and animals.

Always look DOWN AND BEHIND before backing!

BASIC DRIVING

❶

❷

❸

Forward

Travel

Reverse

Travel

Operating the Zero Turn Rider

Figure 9. Turning in Place

Figure 8. Turning Around a Corner

Practice Turning Around a Corner

While traveling forward allow one handle to gradually

return back toward neutral. Repeat several times.

NOTE: To prevent pivoting directly on the tire tread, it is

best to keep both wheels going at least slightly forward.

Practice Turning In Place

To turn in place, “Zero Turn,” gradually move one ground

speed control lever forward from neutral and one lever

back from neutral simultaneously. Repeat several times.

NOTE: Changing the amount each lever is pulled—forward

or back, changes the “pivot point” you turn on.

ADVANCED DRIVING

Executing an

End-Of-Row Zero Turn

Your Zero Turn Rider’s unique ability to turn

in place allows you to turn around at the

end of a cutting row rather than having to

stop and Y-turn before starting a new row.

For example, to execute a right end-of row

Zero Turn:

1. Slow down at the end of the row.

2. Move the LEFT ground speed control

lever forward slightly while moving the

RIGHT ground speed control lever back

to center and then slightly back from

center.

3. Begin mowing forward again.

This technique turns the rider RIGHT and

slightly overlaps the row just cut —

eliminating the need to back up and re-cut

missed grass.

As you become more familiar and experi-

enced with operating the Zero Turn rider,

you will learn more maneuvers that will

make your mowing time easier and more

enjoyable.

Remember, the more you practice, the

better your control of the Zero Turn will be!

Figure 10. Executing an End-Of-Row Turn

Turning

In-Place

Executing

Turns

❶

❷

❸

Figure 12. Mower Components (44” Deck Shown)

A. Mower Cutting Height C. Front Gauge Wheels

Adjustment Lever D. Mower Supports

B. Rear Gauge Wheel E. Idler Pulley Arm

MOWER DECK REMOVAL &

INSTALLATION

NOTE: Perform mower removal and installation on a

hard, level surface such as a concrete floor.

Removing the Mower Deck

1. Swing the front wheels out.

2. Place the mower height adjustment lever (A, Figure

12) in the lowest cutting position.

3. Release tension on the drive belt using the Idler

Pulley Arm (E, Figure 12) and release the drive belt.

4. Disconnect the front hitch by pulling out on the

release rod (A, Figure 11) and lifting the mower hitch

(C, Figure 11) off the rider hitch bracket (B, Figure 11).

5. Slide the mower deck forward and out from under the

right side of the rider.

Installing the Mower Deck

1. Swing the front wheels out.

2. Place the mower height adjustment lever (A, Figure 12)

in the lowest cutting position.

3. Slide the mower deck under the right side of the rider,

and then back, making certain the mower supports

(D, Figure 12) are properly located onto the rider sup-

port plates (see D, Figure 11).

4. Attach the drive belt.

5. Connect the mower hitch to the front rider hitch by

pulling out on the release rod (See Figure 11).

ADJUSTING MOWER

CUTTING HEIGHT

The Mower Height Adjustment Lever (A, Figure 13) con-

trols the cutting height of the mower deck. Move the

lever LEFT and then to the desired cutting height.

Moving the lever FORWARD decreases the cutting

height, and BACK raises the cutting height.

The front gauge wheels are used only to help prevent

scalping. The front gauge wheels are permanently

mounted.

Operating the Zero Turn Rider

Figure 11. Mower Hitch Components

A. Rider Hitch Bracket C. Mower Hitch

B. Release Rod D. Rider/Mower Supports

WARNING

Engage parking brake, disengage PTO, stop

engine and remove key before attempting to

install or remove the mower.

Figure 13. Adjusting Mower Deck Gauge Wheels

A. Mower Height Adjustment Lever

Page is loading ...

Simplicity 1693300 User manual

Brand: Simplicity

Model: 1693300

Category: Lawnmowers

Type: User manual

This manual is also suitable for

Download PDF

report

Simplicity 1693300 User manual

This manual is also suitable for

Simplicity 1693300 User manual

Related papers

Other documents