SmartCell ZX Administrator
Installation Guide
35 Industrial Wa
y
Rochester, NH 03867
USA
(603) 332-9400
Part number 04-0043-01 Rev. A
ii SmartCell ZX Administrator Installation Guide
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information contained in this
document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any
such changes have been made. The hardware, firmware, or software described in this manual are subject to change
without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL,
OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS)
ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF
CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE
POSSIBILITY OF SUCH DAMAGES.
Copyright 1997 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH03866-5005
All Rights Reserved
Printed in the United States of America
SmartCell ZX Administrator Installation Guide
Part Number: 04-0043-01 Rev. A
SmartCell, SPECTRUM, LANVIEW, MicroMMAC, and BRIM are registered trademarks and Element Manager,
EPIM, EPIMA, EPIM-F1, EPIM-F2, EPIM-F3, EPIM-T, EPIM-X, FOT-F, FOT-F3, HubSTACK, SEH, SEHI, and
TMS-3 are trademarks of Cabletron Systems, Inc. All other product names mentioned in this manual may be
trademarks or registered trademarks of their respective companies.
SmartCell ZX Administrator Installation Guide iii
REVISION HISTORY
Document Name: SmartCell ZX Administrator Installation Guide
Document Part Number: 04-0043-01 Rev. A
Author: Carre Gibson
Editor: Ayesha Maqsood
Date Revision Description
July 1997 A Initial Release
iv SmartCell ZX Administrator Installation Guide
SmartCell ZX Administrator Installation Guide v
TABLE OF CONTENTS
1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1 Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.2 Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.3 Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.4 Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 Installing SmartCell ZX Administrator on Windows NT 4.0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2.1 Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2.2 Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.3 Installing SmartCell ZX Administrator on Windows NT 3.51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.3.1 Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.3.2 Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
2.4 Installing SmartCell ZX Administrator on Windows 95 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.4.1 Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.4.2 Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
3 Gettin
g
Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Starting SmartCell ZX Administrator the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
3.2 Changing Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3 Starting SmartCell ZX Administrator After the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.4 Adding a User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.5 Accessing Online Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.6 Uninstalling SmartCell ZX Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
A Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
A.1 Telephone Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
A.2 Fax Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
A.3 Electronic Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
A.4 Placing A Support Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
vi SmartCell ZX Administrator Installation Guide
Table of contents
A.5 Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
A.5.1 Hardware Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
A.5.2 Software Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
A.6 Repair Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
B Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-1
SmartCell ZX Administrator Installation Guide vii
LIST OF TABLES
3-1 Default User Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
viii SmartCell ZX Administrator Installation Guide
List of Tables
SmartCell ZX Administrator Installation Guide 1-1
1 INTRODUCTION
SmartCell ZX Administrator is a Windows application that manages SmartCell ZX ATM switches. It supports the
following applications:
• Switch management
• Emulated Local Area Network (ELAN) management
• Connection management
• Alarm management
• Switch discovery
You can use SmartCell ZX Administrator to perform most of the tasks that you can do with the SmartCell
6A000/ZX-250 console interface. The tasks that you cannot perform with SmartCell ZX Administrator are debugging
and tracing: You cannot control the console debugging and tracing options.
With SmartCell ZX Administrator, you can perform the following tasks that are not available from the console
interface:
• Use the graphical user interface
• Manage all switches from one console
• Perform transactions across multiple switches (for example, create an ELAN when the servers are
not co-located
• Perform transactions with drag and drop
This manual contains the information you need to get started with the application. After installation, refer to the online
help for descriptions of how to use the product.
1.1 AUDIENCE
SmartCell ZX Administrator is designed for network administrators and managers. To use this product effectively, you
should know how to install and use Windows applications. You also should understand networking in general and ATM
in particular. Refer to the SmartCell 6A000 User Guide and SmartCell ZX-250 User Guide for information about how
the switch works.
1.2 CONTENT
Chapter 2, "Installation," tells how to install the application on Windows NT 4.0, Windows NT 3.51, and Windows 95.
Chapter 3, "Getting Started," tells how to do the following tasks:
• Start the application the first time
• Start the application after the first time
• Add a user
• Access online help
• Uninstall the application
1-2 SmartCell ZX Administrator Installation Guide
Conventions Introduction
Chapter 4, "ATM Acronyms," spells out the ATM acronyms used on the SmartCell ZX Administrator screens.
Appendix A, "Technical Support," gives instructions for contacting Cabletron by telephone, fax, electronic mail, and
the World Wide Web.
1.3 CONVENTIONS
Characters that you type appear in Courier boldface type.
Example: Enter
a:\setup.exe
means that you should type "a:\setup.exe" and then press the Enter key.
Variables for which you supply a value appear in angle brackets (<>). Replace the brackets and the variable name with
the appropriate value.
Example:
<path>
means that you should replace "<path>" with the location of a file like "c:\documents\myfile"
1.4 RELATED MANUALS
The SmartCell 6A000/ZX-250 Reference Manual describes the console commands.
The SmartCell ZX-250 User Guide and SmartCell 6A000 User Guide tell how to install, configure, use and
troubleshoot the switch.
SmartCell ZX Administrator Installation Guide 2-1
2INSTALLATION
You can install SmartCell ZX Administrator on a PC running Windows NT 4.0, Windows NT 3.51, or Windows 95.
You can install the software from the diskette drive (drive a:) on your PC or from a server on your network.
After you read this chapter, you will be able to install the application on the following platforms:
• Windows NT 4.0
• Windows NT 3.51
• Windows 95
2.1 HARDWARE REQUIREMENTS
Before you install SmartCell ZX Administrator, verify that your PC has the following hardware:
• Pentium 133 or faster processor
• 20 MB disk space
• 32 MB RAM
• Monitor with resolution of at least 800 x 600 resolution
• IP network connection to the switch you manage
2.2 INSTALLING SMARTCELL ZX ADMINISTRATOR
ON WINDOWS NT 4.0
2.2.1 Software Requirements
Before you install SmartCell ZX Administrator, verify that the Windows NT 4.0 operating system is installed on your
PC.
2.2.2 Installation Steps
Follow these steps to install SmartCell ZX Administrator.
1. If you are using diskettes, make backup copies of the SmartCell ZX Administrator diskettes. Put the
original diskettes in a safe place; use them if your backup copies become unusable. Use your backup
copies to complete the installation procedure.
2. Load Disk1 into drive a or note the network <path> to the directory that contains the SmartCell ZX
Administrator files. The term <path> is the location of the files on your server.
3. Click Start then click Run.
2-2 SmartCell ZX Administrator Installation Guide
Installin
g
SmartCell ZX Administrator on Windows NT 3.51 Installation
4. Enter a:\setup.exe to install from drive a
OR
<path>\Disk1\setup.exe to install from the network
5. The Software License Agreement dialog box appears. Follow the instructions on the screen and click
Yes to proceed.
6. The Welcome dialog box appears. Read the instructions and click Next to proceed.
7. The Choose Destination Location screen appears. Follow the instructions on the screen and click
Next. Setup performs the following tasks:
- Copies several files to c:\ZXAdmin or to the destination you selected
- Creates a program group called SmartCell ZX Network Management Tools (Common)
- Creates icons in the group for
SmartCell ZX Administrator–starts the application
Online Help–starts the online help
Readme–displays release notes
UnInstall SmartCell ZX Administrator–removes the application from your PC
8. The Setup Complete dialog box appears. Read the message and click Finish.
9. The Information dialog box appears. Click OK.
10. Log off and log on before using SmartCell ZX Administrator.
2.3 INSTALLING SMARTCELL ZX ADMINISTRATOR
ON WINDOWS NT 3.51
2.3.1 Software Requirements
Before you install SmartCell ZX Administrator, verify that the Windows NT 3.51 operating system is installed on your
PC.
2.3.2 Installation Steps
Follow these steps to install SmartCell ZX Administrator.
1. If you are using diskettes, make backup copies of the SmartCell ZX Administrator diskettes. Put the
original diskettes in a safe place; use them if your backup copies become unusable. Use your backup
copies to complete the installation procedure.
2. Load Disk1 into drive a or note the network <path> to the directory that contains the SmartCell ZX
Administrator files. The term <path> is the location of the files on your server.
3. On the File menu, click Run.
4. Enter a:\setup.exe to install from drive a
OR
<path>\Disk1\setup.exe to install from the network
SmartCell ZX Administrator Installation Guide 2-3
Installation Installin
g
SmartCell ZX Administrator on Windows 95
5. The Software License Agreement dialog box appears. Follow the instructions on the screen and click
Yes to proceed.
6. The Welcome dialog box appears. Read the instructions and click Next to proceed.
7. The Choose Destination Location screen appears. Follow the instructions on the screen and click
Next. Setup performs the following tasks:
- Copies several files to c:\ZXAdmin or to the destination you selected
- Creates a program group called SmartCell ZX Network Management Tools (Common)
- Creates icons in the group for
SmartCell ZX Administrator–starts the application
Online Help–starts the online help
Readme–displays release notes
UnInstall SmartCell ZX Administrator–removes the application from your PC
8. The Setup Complete dialog box appears. Read the messages and click Finish.
9. The Information dialog box appears. Click OK.
10. Log off and log on before using SmartCell ZX Administrator.
2.4 INSTALLING SMARTCELL ZX ADMINISTRATOR
ON WINDOWS 95
2.4.1 Software Requirements
Before you install SmartCell ZX Administrator, verify that the Windows 95 operating system is installed on your PC.
2.4.2 Installation Steps
Follow these steps to install SmartCell ZX Administrator.
1. If you are using diskettes, make backup copies of the SmartCell ZX Administrator diskettes. Put the
original diskettes in a safe place; use them if your backup copies become unusable. Use your backup
copies to complete the installation procedure.
2. Load Disk1 into drive a or note the network <path> to the directory that contains the SmartCell ZX
Administrator files. The term <path> is the location of the files on your server.
3. Click Start then click Run.
4. Enter a:\setup.exe to install from drive a
OR
<path>\Disk1\setup.exe to install from the network
5. The Software License Agreement dialog box appears. Follow the instructions on the screen and click
Yes to proceed.
6. The Welcome dialog box appears. Read the instructions and click Next to proceed.
7. The Choose Destination Location screen appears. Follow the instructions on the screen and click
Next. Setup performs the following tasks:
2-4 SmartCell ZX Administrator Installation Guide
Installin
g
SmartCell ZX Administrator on Windows 95 Installation
- Copies several files to c:\ZXAdmin or to the destination you selected
- Creates a group called SmartCell ZX Network Management Tools (Common)
- Creates icons in the group for
SmartCell ZX Administrator–starts the application
Online Help–starts the online help
Readme–displays release notes
UnInstall SmartCell ZX Administrator–removes the application from your PC
8. The Setup Complete dialog box appears. Read the message and click Finish.
9. The Information dialog box appears. Click OK.
10. Log off and log on before using SmartCell ZX Administrator.
SmartCell ZX Administrator Installation Guide 3-1
3 GETTING STARTED
Most of the instructions for using SmartCell ZX Administrator appear in the online help. This chapter describes a few
tasks that you need to know about as you begin to use the application.
After you read this chapter, you will be able to perform the following tasks:
• Starting SmartCell ZX Administrator the first time
• Starting SmartCell ZX Administrator after the first time
• Adding a user
• Accessing online help
• Uninstalling SmartCell ZX Administrator
3.1 STARTING SMARTCELL ZX ADMINISTRATOR
THE FIRST TIME
When you use SmartCell ZX Administrator for the first time, you should change the default passwords to prevent
unauthorized access to the application. The application arrives with two user accounts set up, as described in Table 3-1.
1. In the SmartCell ZX Network Management Tools (Common) program group, double click on the
icon labeled SmartCell ZX Administrator. The SmartCell ZX Administrator Login dialog box
appears.
2. Enter the default user name, admin. The user name is case sensitive.
3. Enter the default password, admin, and click the OK button or press Enter. The password is case
sensitive.
4. The SmartCell ZX Administrator window appears. On the Applications menu, select User
Management.
Table 3-1 Default User Accounts
User Name Access Level Default Password
admin Administrator admin
guest Guest guest
3-2 SmartCell ZX Administrator Installation Guide
Chan
g
in
g
Passwords Gettin
g
Started
3.2 CHANGING PASSWORDS
1. The User Account Management dialog box appears. Follow steps 2-8 to change the admin and guest
passwords.
2. In the List of Users, select admin.
3. In the User Profile, type your new password in the Password field, and type it again in the Confirm
Password field.
4. Click the Update Profile button.
5. In the List of Users, select guest.
6. In the User Profile, type your new password in the Password field, and type it again in the Confirm
Password field.
7. Click the Update Profile button.
8. Click the Close button to return to the SmartCell ZX Administrator window. You are ready to use
the application to manage your switch.
3.3 STARTING SMARTCELL ZX ADMINISTRATOR
AFTER THE FIRST TIME
After you have started SmartCell ZX Administrator the first time and changed the default passwords, you log in to the
application just as you would any Windows program. The following steps describe the procedure:
1. In the SmartCell ZX Network Management Tools (Common) program group, double click the icon
labeled SmartCell ZX Administrator. The SmartCell ZX Administrator Login dialog box appears.
2. Enter your user name and press the Tab key. The user name is case sensitive.
3. Enter your password and click the OK button. The password is case sensitive. The SmartCell ZX
Administrator window appears. You are ready to use the application to manage your switch.
3.4 ADDING A USER
1. Log in using a user name whose Access Level is set to Administrator.
2. The SmartCell ZX Administrator window appears. On the Applications menu, select User
Management.
3. The User Account Management dialog box appears. In the User Profile, enter the new user name in
the Name field.
4. Select the Access Level with the pull-down menu.
5. Use the Tab key to move from field to field. The Full Name and Description are optional.
6. Enter the password in the Password field, press Tab, and enter the password again in the Confirm
Password field.
7. Click the Add Acct button.
8. Click the Close button to return to the main window.
SmartCell ZX Administrator Installation Guide 3-3
Gettin
g
Started Accessin
g
Online Help
3.5 ACCESSING ONLINE HELP
1. From the Help menu, select SmartCell ZX Administrator Help Topics.
2. The Help Topics dialog box appears. You have three options for viewing online help:
- Click the Contents tab to show the Table of Contents of the online help. Click on the topic you
wish to read about.
- Click the Index tab to select from an alphabetical list of help topics.
- Click the Find tab to search for a particular topic.
3.6 UNINSTALLING SMARTCELL ZX
ADMINISTRATOR
1. In the SmartCell ZX Network Management Tools (Common) program group, double click UnInstall
SmartCell ZX Administrator.
2. The Confirm File Deletion dialog box appears. Click the Yes button.
3. The Remove Programs From Your Computer dialog box appears. Click the OK button. The uninstall
procedure is complete.
Your configuration database files remain on the disk. You can install the same or a different version of SmartCell ZX
Administrator. The newly installed application will find your database.
3-4 SmartCell ZX Administrator Installation Guide
Uninstallin
g
SmartCell ZX Administrator Gettin
g
Started
SmartCell ZX Administrator Installation Guide Appendix A-1
Technical Support Telephone Assistance
APPENDIX A TECHNICAL SUPPORT
This appendix tells you what to do if you need technical support for the SmartCell ZX Administrator application or for
the SmartCell switch.
Cabletron offers several support and service programs designed to provide high-quality support to our customers. For
technical support, first contact your place of purchase. If you need additional assistance, contact Cabletron Systems,
Inc. Refer below to several easy ways to reach Cabletron Customer Support and Service.
A.1 TELEPHONE ASSISTANCE
Our Technical Support Center is available Monday through Friday, 8am to 8pm Eastern Time, by calling
603-332-9400.
A.2 FAX SERVICE
You can fax support questions to us any time at 603-337-3075.
A.3 ELECTRONIC SERVICES
Dial the Cabletron Bulletin Board Service at 603-335-3358.
Send us e-mail at suppor[email protected].
You can also check our home pages on the World Wide Web:
http://www.Cabletron.com
http://www.ctron.com
A.4 PLACING A SUPPORT CALL
To expedite your inquiry, please provide the following information:
Your Name
Your Company Name
Address
Email Address
Phone Number
FAX Number
Appendix A-2 SmartCell ZX Administrator Installation Guide
Warranty Information Technical Support
Detailed description of the issue (including history, what you've tried, and conditions under which
you see this problem occur)
Hardware model number, software version, and switch configuration (that is, what part types are in
what slots)
A.5 WARRANTY INFORMATION
A.5.1 Hardware Warranty
Cabletron warrants its products against defects in the physical product for one year from the date of receipt by the end
user (as shown by Proof of Purchase). A product that is determined to be defective should be returned to the place of
purchase. For more detailed warranty information, consult the Product Warranty Statement received with your product.
A.5.2 Software Warranty
Cabletron software products carry a 90-day software warranty. During this period, customers may receive updates and
patches for verified, reported software issues.
A.6 REPAIR SERVICES
Cabletron offers an out-of-warranty repair service at our Santa Clara Repair Facility. Products returned for repair will
be repaired and returned within 5 working days. A product sent to Cabletron Systems, Inc. for repair must first be
assigned a Return Material Authorization (RMA) number. A product sent to Cabletron Systems, Inc., without an RMA
number displayed outside the box will be returned to the sender unopened, at the sender's expense.
To obtain an RMA number, contact the Cabletron Technical Support. When you call for an RMA number, your support
representative will spend a few minutes with you, making sure the board is defective. Once they confirm the board is
defective, they will assign an RMA number. Payment, shipping instructions, and turnaround time will be confirmed
when the RMA number is assigned.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
