H3C LSW148POEM Command Reference Manual

Brand: H3C

Model: LSW148POEM

Type: Command Reference Manual

H3C S5820X&S5800 Series Ethernet Switches

IRF

Command Reference

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document Version: 6W103-20100716

Product Version: Release 1110

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

Care,

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

G, V

G, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Preface

The H3C S5800&S5820X documentation set includes 11 command references, which describe the

commands and command syntax options for the S5800&S5820X Release 1110.

The IRF Command Reference describes IRF configuration commands for creating an IRF virtual device.

It covers the commands for binding physical ports to an IRF port, configuring the member switch ID and

priority, and detecting and maintaining the IRF link.

This preface includes:

z Audience

z Document Organization

z Conventions

z About the H3C S5820X&S5800 Documentation Set

z Obtaining Documentation

z Documentation Feedback

Audience

This documentation set is intended for:

z Network planners

z Field technical support and servicing engineers

z Network administrators working with the S5800 and S5820X series

Document Organization

The IRF Command Reference comprises the following part:

IRF Configuration

Commands

Conventions

This section describes the conventions used in this documentation set.

Command conventions

Convention Description

Boldface Bold text represents commands and keywords that you enter literally as shown.

italic

Italic text represents arguments that you replace with actual values.

[ ]

Square brackets enclose syntax choices (keywords or arguments) that are

optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars,

from which you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical

bars, from which you select one or none.

Convention Description

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by

vertical bars, from which you select at least one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by

vertical bars, from which you may select multiple choices or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&)

sign can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in Boldface.

For example, the New User window appears; click OK.

Multi-level menus are separated by angle brackets. For example, File > Create

> Folder.

Symbols

Convention Description

Means reader be careful. Improper operation may cause data loss or damage to

equipment.

Means a complementary description.

About the H3C S5820X&S5800 Documentation Set

The H3C S5800&S5820X documentation set also includes:

Category Documents Purposes

Marketing brochures Describe product specifications and benefits.

Product description and

specifications

Technology white papers

Provide an in-depth description of software features

and technologies.

PSR150-A [ PSR150-D ]

Power Modules User

Manual

Describes the appearances, features, specifications,

installation, and removal of the pluggable 150W power

modules available for the products.

PSR300-12A

[ PSR300-12D1 ] Power

Modules User Manual

Describes the appearances, features, specifications,

installation, and removal of the pluggable 300W power

modules available for the products.

PSR750-A [ PSR750-D ]

Power Modules User

Manual

Describes the appearances, features, specifications,

installation, and removal of the pluggable 750W power

modules available for the products.

RPS User Manual

Describes the appearances, features, and

specifications of the RPS units available for the

products.

Pluggable module

description

LSW1FAN and

LSW1BFAN Installation

Manual

Describes the appearances, specifications,

installation, and removal of the pluggable fan modules

available for the products.

Category Documents Purposes

LSW148POEM Module

User Manual

Describes the appearance, features, installation, and

removal of the pluggable PoE module available for the

products.

S5820X [ S5800 ] Series

Ethernet Switches

Interface Cards User

Manual

Describes the models, hardware specifications,

installation, and removal of the interface cards

available for the products.

H3C OAP Cards User

Manual

Describes the benefits, features, hardware

specifications, installation, and removal of the OAP

cards available for the products.

H3C Low End Series

Ethernet Switches

Pluggable Modules

Manual

Describes the models, appearances, and

specifications of the pluggable modules available for

the products.

S5800-60C-PWR

Ethernet Switch Hot

Swappable Power

Module Ordering Guide

Guides you through ordering the hot-swappable power

modules available for the S5800-60C-PWR switches

in different cases.

Power configuration

RPS Ordering

Information for H3C

Low-End Ethernet

Switches

Provides the RPS and switch compatibility matrix and

RPS cable specifications.

z S5800 Series

Ethernet Switches

Quick Start

z S5820X Series

Ethernet Switches

Quick Start

z S5800 Series

Ethernet Switches

CE DOC

z S5820X Series

Ethernet Switches

CE DOC

Provides regulatory information and the safety

instructions that must be followed during installation.

z S5800 Series

Ethernet Switches

Quick Start

z S5820X Series

Ethernet Switches

Quick Start

Guides you through initial installation and setup

procedures to help you quickly set up and use your

device with the minimum configuration.

z S5800 Series

Ethernet Switches

Installation Manual

z S5820X Series

Ethernet Switches

Installation Manual

Provides a complete guide to hardware installation

and hardware specifications.

Hardware installation

Pluggable

SFP[SFP+][XFP]

Transceiver Modules

Installation Guide

Guides you through installing SFP/SFP+/XFP

transceiver modules.

Category Documents Purposes

z S5800-60C-PWR

Switch Video

Installation Guide

z S5820X-28C Switch

Video Installation

Guide

Shows how to install the H3C S5800-60C-PWR and

H3C S5820X-28C Ethernet switches.

Configuration guide

Describe software features and configuration

procedures.

Software configuration

Command reference Provide a quick reference to all available commands.

H3C Series Ethernet

Switches Login

Password Recovery

Manual

Tells how to find the lost password or recover the

password when the login password is lost.

Operations and

maintenance

Release notes

Provide information about the product release,

including the version history, hardware and software

compatibility matrix, version upgrade information,

technical support information, and software upgrading.

Obtaining Documentation

You can access the most up-to-date H3C product documentation on the World Wide Web at

http://www.h3c.com.

Click the links on the top navigation bar to obtain different categories of product documentation:

[Technical Support & Documents > Technical Documents] – Provides hardware installation, software

upgrading, and software feature configuration and maintenance documentation.

[Products & Solutions] – Provides information about products and technologies, as well as solutions.

[Technical Support & Documents > Software Download] – Provides the documentation released with

the software version.

Documentation Feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

Table of Contents

1 IRF Configuration Commands··················································································································1-1

IRF Configuration Commands ················································································································1-1

display irf ·········································································································································1-1

display irf configuration····················································································································1-2

display irf topology···························································································································1-3

display irf-port load-sharing mode···································································································1-4

display mad ·····································································································································1-6

display switchover state···················································································································1-7

irf auto-update enable······················································································································1-9

irf domain·······································································································································1-10

irf link-delay ···································································································································1-10

irf mac-address persistent·············································································································1-11

irf member priority··························································································································1-12

irf member renumber·····················································································································1-13

irf switch-to ····································································································································1-14

irf-port············································································································································1-15

irf-port load-sharing mode (system view)······················································································1-16

irf-port load-sharing mode (IRF port view)·····················································································1-17

irf-port-configuration active············································································································1-18

mad bfd enable······························································································································1-19

mad enable····································································································································1-20

mad exclude interface···················································································································1-21

mad ip address······························································································································1-22

mad restore ···································································································································1-23

port group interface ·······················································································································1-23

2 Index ···························································································································································2-1

1-1

1 IRF Configuration Commands

IRF Configuration Commands

display irf

Syntax

display irf

View

Any view

Default Level

1: Monitor level

Parameters

None

Description

Use the display irf command to display information about the current Intelligent Resilient Framework

(IRF) virtual device, which has the device you are working on as its member.

The command displays information about members of an IRF virtual device, and information about

devices that are joining this IRF virtual device.

Examples

# Display information about the current IRF virtual device.

<Sysname> display irf

Switch Role Priority CPU-Mac

+1 Slave 29 00e0-fc00-1115

2 Slave 1 00e0-fc00-1615

*3 Master 32 00e0-fc00-1015

9 Slave 30 00e0-fc00-1515

--------------------------------------------------------

* indicates the device is the master.

+ indicates the device through which the user logs in.

The Bridge MAC of the IRF is: 00e0-fc00-1000

Auto upgrade : yes

Mac persistent : always

Domain ID : 30

1-2

Table 1-1 display irf command output description

Field Description

Switch

Member ID.

z The ID with * indicates that the device is the master;

z The ID with + indicates that it is the device that you are working on.

Role

The role of a member of the IRF virtual device, which takes the following

values:

z Slave

z Master

z SlaveWait: Joining the IRF virtual device.

z Loading: Loading the system boot file.

CPU-MAC Bridge MAC address of the device

Auto upgrade

Whether auto upgrade of configuration files is enabled:

z yes: Enabled

z no: Disabled

MAC persistent

Whether bridge MAC address preservation is enabled:

z 6 min: When the master leaves, the bridge MAC address does not

change within six minutes.

z always: No matter whether the master leaves the IRF virtual device or

not, the bridge MAC address remains unchanged.

z no: As soon as the master leaves, the IRF virtual device uses the

bridge MAC address of the newly elected master as its bridge MAC

address.

Domain ID

Domain ID assigned to an IRF virtual device. A domain ID is used to

uniquely identify an IRF virtual device when there are multiple IRF virtual

devices in the network.

display irf configuration

Syntax

display irf configuration

View

Any view

Default Level

1: Monitor level

Parameters

None

Description

Use the display irf configuration command to display the pre-configurations of members of the

current IRF virtual device.

The pre-configurations take effect at the reboot of the device. The command displays the member ID,

priority, IRF port state, and port information.

1-3

Examples

# Display the pre-configurations of all members of the current IRF virtual device.

<Sysname> display irf configuration

MemberID NewID IRF-Port1 IRF-Port2

*2 2 Ten-GigabitEthernet2/0/28 Ten-GigabitEthernet2/0/26

+3 4 Ten-GigabitEthernet3/0/25 Ten-GigabitEthernet3/0/27

--------------------------------------------------------

* indicates the device is the master.

+ indicates the device through which the user logs in.

Table 1-2 display irf configuration command output description

Field Description

Switch

Member ID

The ID with * indicates that the device is the master;

The ID with + indicates that it is the device that you are working on.

NewID The member ID configured for a device after its reboot

Priority The priority configured for a device after its reboot

IRF-Port1

Configuration of IRF–Port1. If it is displayed as multiple ports, it indicates that

the IRF port is aggregated from these physical IRF ports; If it is displayed as

disable, it indicates that the IRF port is not enabled.

IRF-Port2

Configuration of IRF–Port2. If it is displayed as multiple ports, it indicates that

the IRF port is aggregated from these physical IRF ports; If it is displayed as

disable, it indicates that the IRF port is not enabled.

display irf topology

Syntax

display irf topology

View

Any view

Default Level

1: Monitor level

Parameters

None

Description

Use the display irf topology command to display topology information about the current IRF virtual

device.

The command displays all topology information learned by the current device.

Examples

# Display topology information about the current IRF virtual device.

1-4

<Sysname> display irf topology

Topology Info

-----------------------------------------------------------------------

IRF-Port1 IRF-Port2

Switch Link neighbor Link neighbor Belong To

1 DOWN -- UP 2 000f-cbb8-1a82

2 UP 1 UP 3 000f-cbb8-1a82

*+3 UP 2 DIS -- 000f-cbb8-1a82

--------------------------------------------------------------------------

* indicates the device is the master.

+ indicates the device through which the user logs in.

Table 1-3 display irf topology command output description

Field Description

Switch

Member ID (The ID with * indicates that the device is the master; the ID with +

indicates that it is the device that you are working on.)

IRF-Port 1 Information of IRF-Port 1, including link (link state) and neighbor.

IRF-Port 2 Information of the IRF-Port 2, including link and neighbor.

Link

Link state of the IRF port:

z UP

z DOWN

z DIS: The IRF port is not enabled.

neighbor

The device ID that connects to this IRF port

If the IRF port does not connect to any device, -- is displayed.

Belong To

The IRF virtual device that the device belongs to, represented by the CPU MAC

address of the master.

display irf-port load-sharing mode

Syntax

display irf-port load-sharing mode [ irf-port [ member-id/port-number ] ]

View

Any view

Default Level

1: Monitor level

Parameters

irf-port: Displays the load sharing mode on an aggregate IRF port.

member-id/port-number: IRF port number, where, member-id represents the member ID of a member

of the IRF virtual device, which you can display with the display irf command. The port-number

argument specifies the port number, and the value can be either 1 or 2.

1-5

Description

Use the display irf-port load-sharing mode command to display the global IRF port load sharing

mode, or the load sharing mode on an aggregate IRF port.

Note that:

z If the irf-port keyword is not provided, execution of this command displays the global IRF port

load sharing mode.

z If the irf-port keyword is provided and the IRF port number is not specified, execution of this

command displays the load sharing mode of all IRF ports.

Examples

# Display the global IRF port load sharing mode.

z Default configuration:

<Sysname> display irf-port load-sharing mode

irf-port Load-Sharing Mode:

Layer 2 traffic: packet type-based sharing

Layer 3 traffic: packet type-based sharing

z Non-default configuration:

<Sysname> display irf-port load-sharing mode

irf-port Load-Sharing Mode:

destination-mac address, source-mac address

# Display the load sharing mode on IRF port 1/1.

z Default configuration:

<Sysname> display irf-port load-sharing mode irf-port 1/1

irf-port 1/1 Load-Sharing Mode:

Layer 2 traffic: packet type-based sharing

Layer 3 traffic: packet type-based sharing

z Non-default configuration:

<Sysname> display irf-port load-sharing mode irf-port 1/1

irf-port 1/1 Load-Sharing Mode:

destination-mac address, source-mac address

# Display load sharing mode of all IRF ports.

<Sysname> display irf-port load-sharing mode irf-port

irf-port 1/1 Load-Sharing Mode:

destination-ip address, source-ip address,

irf-port 1/2 Load-Sharing Mode:

Layer 2 traffic: destination-mac address, source-mac address

1-6

Layer 3 traffic: destination-ip address, source-ip address

Table 1-4 display irf-port load-sharing mode command output description

Field Description

irf-port Load-Sharing Mode

Global IRF port load sharing mode:

z If default configuration is applied, port load sharing mode for

processing both Layer 2 and Layer 3 packets is displayed.

z If non-default configuration is applied, user configured load

sharing mode is displayed.

irf-port 1/1 Load-Sharing Mode

IRF port load sharing mode on IRF port 1/1:

z If default configuration is applied, the global IRF port load

sharing mode is displayed.

z If non-default configuration is applied, user configured load

sharing mode is displayed.

Layer 2 traffic: packet type-based

sharing

Default port load sharing mode for processing Layer 2 packets:

uses the combination of both the source and the destination MAC

addresses as the hash key for load sharing.

Layer 3 traffic: packet type-based

sharing

Default port load sharing mode for processing Layer 3 packets:

uses the combination of both the source and the destination IP

addresses as the hash key for load sharing.

destination-mac address, source-mac

address

User configured load sharing mode: uses the combination of both

the source and the destination MAC addresses as the hash key

for load sharing.

display mad

Syntax

display mad [ verbose ]

View

Any view

Default Level

1: Monitor level

Parameters

verbose: Displays detailed information about the MAD detection. If this keyword is not provided, the

system displays brief information about the MAD detection.

Description

Use the display mad command to display information about the MAD detection.

Examples

# Display brief information about the MAD detection.

<Sysname> display mad

MAD LACP enabled.

MAD BFD enabled.

# Display detailed information about the MAD detection.

1-7

<Sysname> display mad verbose

Current MAD status: Detect

Excluded ports(configurable):

GigabitEthernet2/0/2

GigabitEthernet2/0/3

Excluded ports(can not be configured):

Ten-GigabitEthernet2/0/25

Ten-GigabitEthernet3/0/26

MAD enabled aggregation port:

Bridge-Aggregation2

MAD BFD enabled interface:

Vlan-interface2

mad ip address 10.0.0.2 255.255.0.0 member 2

mad ip address 10.0.0.3 255.255.0.0 member 3

Table 1-5 display mad command output description

Field Description

Current MAD status

Current state of the MAD detection, including:

z Detect: Detect state, that is, the IRF virtual device is in a

normal state.

z Recovery: When multi-active collision occurs, the loser side

enters the recovery state, and all unreserved ports are

automatically disabled.

z Detect to Recovery: The intermediate state between detect

and recovery.

z Recovery to Detect: The intermediate state between

recovery and detect.

Excluded ports(configurable) User-configured reserved ports

Excluded ports(can not be configured)

System reserved ports, which do not need to be configured and

are automatically reserved.

MAD enabled aggregation port The aggregation port with LACP MAD detection enabled.

MAD BFD enabled interface The port with BFD MAD detection enabled.

Vlan-interface2

mad ip address 192.168.2.2

255.255.0.0 member 2

mad ip address 192.168.2.3

255.255.0.0 member 3

Information of MAD IP addresses in the IRF virtual device,

including the VLAN interfaces on which MAD IP addresses

have been configured, and the MAD IP addresses on all

member devices.

display switchover state

Syntax

display switchover state [ member-id ]

View

Any view

1-8

Default Level

1: Monitor level

Parameters

member-id: Specifies the ID of a member of an IRF virtual device. The value range depends on the

current number of members and their member IDs. With this argument provided, the command

displays the master/slave switchover state of the specified member. Without this argument, the

command displays the master/slave switchover state of the master.

Description

Use the display switchover state command to display the master/slave switchover states of

members of an IRF virtual device.

An IRF functions like a logical distributed device with multiple standby main boards (SMBs). The

master functions like the active main board (AMB), and the slaves function like the SMBs. An IRF

virtual device uses member IDs to uniquely identify member devices, whereas a distributed device

uses slot IDs to uniquely identify cards. Therefore, in the output information of this command, a

member device is also identified by the slot ID, which is equal to the member ID.

Examples

# Display the master/slave switchover states of the master.

<Sysname> display switchover state

Master HA State to Slot 1: Slave is absent.

Master HA State to Slot 2: Slave is absent.

Master HA State to Slot 4: Waiting batch backup request from slave.

Master HA State to Slot 5: Slave is absent.

Master HA State to Slot 6: Realtime backup to slave.

Master HA State to Slot 7: Realtime backup to slave.

Master HA State to Slot 8: Slave is absent.

Master HA State to Slot 9: Slave is absent.

Master HA State to Slot 10: Slave is absent.

The above information shows that:

z Slaves 1, 2, 5, 8, 9 and 10 are absent, which means that these devices are not in use.

z The master is waiting for the batch backup request from slave 4.

z Slaves 6 and 7 are performing real time backup.

Table 1-6 display switchover state command output description for the master

Field Description

Master HA State to Slot slot-number

Indicates that this output information is generated by the

master.

Describes the master/slave switchover state between the

master and the slave whose slot-number represents its

member ID.

Data smooth The master and the slave are smoothing data.

1-9

# Display the master/slave switchover state of slave 6.

<Sysname> display switchover state 6

Slave HA State: Receiving realtime data.

The above information shows that slave 6 is receiving real time backup data.

Table 1-7 display switchover state command output description for a slave

Field Description

Slave HA State

Indicates that this output information is generated by a slave.

Describes the master/slave switchover state of the slave.

Waiting

The slave is ready, and is waiting to enter the batch backup

state.

irf auto-update enable

Syntax

irf auto-update enable

undo irf auto-update enable

View

System view

Default Level

3: Manage level

Parameters

None

Description

Use the irf auto-update enable command to enable the auto update of boot files for an IRF virtual

device.

Use the undo irf auto-update enable command to disable this function.

This function is enabled by default.

Note the following:

z Ensure that the device and the master have the same software version before adding a device

into the IRF virtual device.

z After automatically loading the master’s boot file, a slave configures the file as the boot file to be

used at the next boot and automatically reboots.

z Because system boot file occupies large memory space, to make the auto upgrade succeed,

ensure that there is enough space on the storage medium of the slave.

z If the downloaded boot file and the local boot file have duplicate file names, the local file is

overwritten. Therefore, ensure that there is not any local file that has the same name as the boot

file to be downloaded.

1-10

Examples

# Enable auto upgrade of boot files for an IRF virtual device.

<Sysname> system-view

[Sysname] irf auto-update enable

irf domain

Syntax

irf domain domain-id

undo irf domain

View

System view

Default Level

3: Manage level

Parameters

domain-id: Domain ID assigned to an IRF virtual device, which is in the range 0 to 4294967295.

Description

Use the irf domain command to assign a domain ID for an IRF virtual device.

Use the irf domain command to restore the default.

By default, the domain ID of an IRF virtual device is 0.

Domain IDs are used to differentiate IRF virtual devices.

Examples

# Set the domain ID of the IRF virtual device to 30.

<Sysname> system-view

[Sysname] irf domain 30

irf link-delay

Syntax

irf link-delay interval

undo irf link-delay

View

System view

Default Level

3: Manage level

1-11

Parameters

interval: Time interval for the link layer to report a link-down event of an IRF virtual device, in

milliseconds, in the range 200 to 2000.

Description

Use the irf link-delay command to set the delay time for the link layer to report a link-down event of

an IRF virtual device.

Use the undo irf link-delay command to restore the default.

By default, the link layer is not enabled to report a link-down event of an IRF virtual device.

Examples

# Set the delay time for the link layer to report a link-down event of the current IRF virtual device to

300 milliseconds.

<Sysname> system-view

[Sysname] irf link-delay 300

irf mac-address persistent

Syntax

irf mac-address persistent { timer | always }

undo irf mac-address persistent

View

System view

Default Level

3: Manage level

Parameters

timer: Bridge MAC address preservation mode for an IRF virtual device. With this keyword specified,

the bridge MAC address is preserved for 6 minutes when the master leaves.

always: Bridge MAC address preservation mode. With this keyword specified, the bridge MAC

address is preserved permanently.

Description

Use the irf mac-address persistent command to configure the preservation time of the bridge MAC

address of an IRF virtual device.

Use the undo irf mac-address persistent command to configure the IRF virtual device not to

preserve the bridge MAC address when the master leaves.

By default, the bridge MAC address of an IRF virtual device is preserved for 6 minutes.

z Preserve for six minutes: When the master leaves, the bridge MAC address does not change

within six minutes. If the master does not come back when the preservation time expires, the IRF

virtual device uses the bridge MAC address of the newly elected master as its bridge MAC

address.

1-12

z Preserve permanently: No matter whether the master leaves the IRF virtual device or not, the

bridge MAC address of the IRF virtual device remains unchanged.

z Not preserved: As soon as the master leaves, the IRF virtual device uses the bridge MAC

address of the newly elected master as its bridge MAC address.

Examples

# Configure the bridge MAC address of the IRF virtual device to be preserved permanently.

<Sysname> system-view

[Sysname] irf mac-address persistent always

irf member priority

Syntax

irf member member-id priority priority

undo irf member member-id priority

View

System view

Default Level

3: Manage level

Parameters

member-id: Specifies the ID of a member of an IRF virtual device. The value range depends on the

current number of members and their member IDs. With this argument provided, you can specify a

priority for another member on this device. To view the member IDs, use the display irf command.

priority: Priority value, in the range 1 to 32.

Description

Use the irf member priority command to specify a priority for a member device.

Use the undo irf member priority command to restore the default.

By default, the priority of a member device is 1.

The greater the priority value, the higher the priority. A member with a higher priority is more likely to

be the master.

Note the following:

z You can specify a priority for a member of the current IRF virtual device only.

z The priority setting takes effect right after your configuration.

Examples

# Specify a priority for the local device.

<Sysname> display irf

Switch Role Priority CPU-Mac

+1 Slave 29 00e0-fc00-1115

2 Slave 1 00e0-fc00-1615

1-13

*3 Master 32 00e0-fc00-1015

9 Slave 30 00e0-fc00-1515

--------------------------------------------------------

* indicates the device is the master.

+ indicates the device through which the user logs in.

The Bridge MAC of the IRF is: 00e0-fc00-1000

Auto upgrade : yes

Mac persistent : always

The above information shows that the member ID of the local device is 3, and you can specify a

priority for the local device by providing its member ID.

<Sysname> system-view

[Sysname] irf member 3 priority 16

# Specify a priority for member 2 of the current IRF virtual device.

<Sysname> system-view

[Sysname] irf member 2 priotiry 32

irf member renumber

Syntax

irf member member-id renumber new-member-id

undo irf member member-id renumber

View

System view

Default Level

3: Manage level

Parameters

member-id: Specifies the ID of a member of an IRF virtual device. The value range depends on the

current number of members and their member IDs. With this argument provided, you can change a

member ID of another member on this device. To view the member IDs, use the display irf

command.

new-member-id: New ID of the IRF member, which ranges from 1 to 10.

Description

Use the irf member renumber command to set a member ID for a device.

Use the undo irf member renumber command to remove the configuration.

By default, the member ID of a member device is 1.

Note the following:

z The above setting takes effect at the reboot of the device.

z For an IRF virtual device, member IDs are not only used to identify devices, but also used to

configure IRF ports and member priorities. Therefore, member ID change may cause device

configuration changes or even losses, so change member ID with caution. For example, three

Page is loading ...

H3C LSW148POEM Command Reference Manual

H3C LSW148POEM Command Reference Manual

H3C LSW148POEM Command Reference Manual

Related papers

Other documents