American Standard 1583.470 User manual

1583.470
American Standard
Brand
American Standard
Model
1583.470
Category
Rack accessories
Type
User manual
COLONY 5’™
WHIRLPOOL AND BATHING POOL
HIGH GLOSS ACRYLIC
COLONY 5’ WHIRLPOOL AND BATHING POOL
❏ 2675.018 Whirlpool featuring System I:
• Acrylic with fiberglass reinforcement
• Dual, molded-in armrests at lumbar area
• 1.0 HP single speed, self-draining pump/motor
with dry run seal
• Factory installed power cord with plug
• Six multi-directional and individually flow-rate
adjustable color-coordinated jets
• Deck-mounted, color-coordinated air switch
On/Off control
• Single, color-coordinated air volume control
• Factory installed and tested whirlpool system
❏ 2675.018C Stay Clean™ Whirlpool Massage
Featuring System I:
• Same as 2675.018 except with the
StayClean™ whirlpool system featuring
Antimicrobial AlphaSan®
❏ 2675.002 Bathing Pool
• Same as above without whirlpool system
Nominal Dimensions: 1524 x 832 x 502mm
(5’ x 32-3/4” x 19-3/4")
© 2003 American Standard Inc.
BV-32
Revised 1/99
To Be Specified - Required:
❏ Color:
❏ Bath Faucet: (specify finish)
❏ Bath Drain: 1583.470 (specify finish)
To Be Specified - Optional:
❏ 5 Foot Acrylic Apron: 9260.018 (specify color)
❏ 5 Foot Apron: 9360.018 (specify color)
❏ Grab Bar Kit: 9822.200-two per kit (specify finish)
❏ Jet Trim Ring Kit: 9860.200-two per kit (specify finish)
❏ Universal Tile Bead Kit: 751755-100
NOTE: Roughing-in dimensions and product
specifica-tions shown on reverse side of page.
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
COLONY 5’™
WHIRLPOOL AND BATHING POOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.
■ REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 3WALL TILING BEAD KIT AND APRON NO. 9260.018 OR 9360.018, AND GRAB BAR KIT NO. 9822.200
AVAILABLE AND MUST BE ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances
established by ANSI Standard Z124.1.These measurements are subject to change or cancellation. No
responsibility is assumed for use of superseded or voided pages.
464 mm
(18-1/4)
38 mm
(1-1/2)
502 mm
(19-3/4)
1-1/2 O.D.TAILPIECE
BATH
SUPPORT
MATERIAL
■ LEVELING STRINGER
NOT FOR SUPPORT
ROUGH
FLOOR
1524 mm
(60)
832 mm
(32-3/4)
OUTLINE OF CUTOUT
1486 mm x 794 mm
(58-1/2 X 31-1/4 )
416 mm
(16-3/8)
216 mm
(8-1/2)
305 mm
(12)
38 mm
(1-1/2)
(6) JETS
79 mm
(3-1/8)
CUTOUT IN FLOOR FOR DRAIN
PUMP
FINISHED
WALL
305 mm
(12)
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(65 & 78)
C/L OF
OVERFLOW
102 mm
(4)
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
70 mm
(2-3/4)
117 mm
(4-5/8)
1-1/2 N.P.T.M.
THREADS
19 mm
(3/4)
229 mm
(9)
C/L OF
SUPPLIES
SEE FITTING
SPECS FOR
DIMENSIONS
(1) AIR VALVE
ON/OFF
SWITCH
PROVIDE ACCESS TO PUMP FOR
SERVICING ON ALL INSTALLATIONS
464 mm
(18-1/4)
38 mm
(1-1/2)
502 mm
(19-3/4)
1-1/2 O.D.TAILPIECE
BATH
SUPPORT
MATERIAL
■ LEVELING STRINGER
NOT FOR SUPPORT
ROUGH
FLOOR
1524 mm
(60)
832 mm
(32-3/4)
OUTLINE OF CUTOUT
1486 mm x 794 mm
(58-1/2 X 31-1/4 )
416 mm
(16-3/8)
216 mm
(8-1/2)
305 mm
(12)
38 mm
(1-1/2)
79 mm
(3-1/8)
CUTOUT IN FLOOR FOR DRAIN
FINISHED
WALL
305 mm
(12)
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
1651 & 1981mm
(65 & 78)
C/L OF
OVERFLOW
102 mm
(4)
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
70 mm
(2-3/4)
117 mm
(4-5/8)
1-1/2 N.P.T.M.
THREADS
19 mm
(3/4)
229 mm
(9)
C/L OF
SUPPLIES
SEE FITTING
SPECS FOR
DIMENSIONS
60 x 32-3/4 x 19-3/4 In.(1524 x832 x 502mm)
95 Lbs. (43 Kg.)
604 Lbs. (275 Kg.)
61 Gal. (230 L.)
42 Gal. (159 L.)
20 x 39 In. (508 x 991mm)
27-1/2 x 56 In.(699 x 1422mm)
14-1/4 In. (362mm)
44 Lbs./Sq. Ft. (213 Kgs/Sq. m.)
15.6
29.6
GENERAL SPECIFICATIONS FOR 2675 WHIRLPOOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
WHIRLPOOL ELECTRICAL SPECIFICATIONS
1.1 HP, 9.9 AMPS, 120V.SYSTEM I PUMP
60 x 32-3/4 x 19-3/4 In.
(1524mm x 832 mm x 502mm)
70 Lbs. (32 Kg.)
579 Lbs. (261 Kg.)
61 Gal. (230 L.)
20 x 39 In. (508 mm x 991mm)
27-1/2 x 56 In.(699 mm x 1422mm)
14-1/4 In. (362mm)
42 Lbs./Sq. Ft. (202 Kgs/Sq. m.)
15.6
29.6
GENERAL SPECIFICATIONS FOR 2675 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
  • Page 1 1
  • Page 2 2

American Standard 1583.470 User manual

1583.470
American Standard
Brand
American Standard
Model
1583.470
Category
Rack accessories
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents