American Standard 2675018.222 User manual

Brand: American Standard

Model: 2675018.222

Type: User manual

INSTALLATION INSTRUCTIONS

THANK YOU...

for selecting an American Standard bath. Your new

bath is shipped to you after careful inspection. The

whirlpool version is completely assembled with pump,

motor, and system piping. All you need to finish the

installation are your selected fittings and electrical

connections for a whirlpool.

To insure maximum performance and pleasure from

this product, please follow the instructions and

cautions.

GENERAL INSTALLATION INFORMATION

Carefully uncrate, peel-out protective film and

inspect your new bath for any shipping damage. If

such damage is found, report it to your vendor

immediately.

After inspection and during installation, protect the bath

from construction damage. After installation, and before

enclosing with wallboard, tile, etc., water test the unit

and check for leaks.

If a whirlpool, do not make modifications to the whirlpool

system or remove pump from factory mounting. This

could adversely affect the safety and performance of the

whirlpool and void the warranty. Do not handle or move

the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided

with the bath and must be ordered separately. Framing

and enclosing materials are provided by others. Check

for availability of optional American Standard wall tiling

bead (required for recess installations).

Protect all finished surfaces of the whirlpool during

construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping har-

ness at any time.

NOTE: Deck-mounted fittings are not recommended.

752445-100 Rev. E

All product names listed herein are trademarks

of American Standard Inc. unless otherwise noted.

HIGH GLOSS ACRYLIC

SHOWN LESS ALL FITTINGS

COLONY™ 5'

WHIRLPOOL/BATHING POOL

List of Optional Components (not included):

• Tile Bead Kit 751755-100*

• Apron Kit*

List of Required Components (not included):

• Drain 1583.470* • Bath Filler*

* see your American Standard Distributor

List of Required Tools and Supplies:

Tools

• Level

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard

Woodworking Tools

• Personal Safety

Equipment

• Caulking Gun

Supplies

• Nails

• Putty

• Caulking (waterproof)

• 2 x 3 or 2 x 4

Stringers

• Drop Cloth

• 15 amp GFI

Outlet

• Cement, Plaster,

Grout

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

60 x 32-3/4 x 19-3/4 In.(1524 x832 x 502mm)

95 Lbs. (43 Kg.)

604 Lbs. (275 Kg.)

61 Gal. (230 L.)

42 Gal. (159 L.)

20 x 39 In. (508 x 991mm)

27-1/2 x 56 In.(699 x 1422mm)

14-1/4 In. (362mm)

44 Lbs./Sq. Ft. (213 Kgs/Sq. m.)

15.6

29.6

GENERAL SPECIFICATIONS FOR 2675 WHIRLPOOL

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

WHIRLPOOL MIN. OPERATING VOL.

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

PTS.

CUBE (FT

)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

1.1 HP, 9.9 AMPS, 120V.PUMP

464 mm

(18-1/4)

38 mm

(1-1/2)

502 mm

(19-3/4)

1-1/2 O.D.TAILPIECE

BATH

SUPPORT

MATERIAL

■ LEVELING STRINGER

NOT FOR SUPPORT

ROUGH

FLOOR

1524 mm

(60)

832 mm

(32-3/4)

OUTLINE OF CUTOUT

1486 mm x 794 mm

(58-1/2 X 31-1/4 )

416 mm

(16-3/8)

216 mm

(8-1/2)

305 mm

(12)

38 mm

(1-1/2)

(6) JETS

79 mm

(3-1/8)

CUTOUT IN FLOOR FOR DRAIN

PUMP

FINISHED

WALL

305 mm

(12)

OPTIONAL TO

FINISHED FLOOR

USUALLY BETWEEN

1651 & 1981mm

(65 & 78)

C/L OF

OVERFLOW

102 mm

(4)

C/L OF

SPOUT

C/L OF

VALVES

C/L OF

SHOWER ARM

70 mm

(2-3/4)

117 mm

(4-5/8)

1-1/2 N.P.T.M.

THREADS

19 mm

(3/4)

229 mm

(9)

C/L OF

SUPPLIES

SEE FITTING

SPECS FOR

DIMENSIONS

(1) AIR VALVE

ON/OFF

SWITCH

PROVIDE ACCESS TO PUMP FOR

SERVICING ON ALL INSTALLATIONS

2675 SERIES

1486mm

(58-1/2)

CUTOUT

TYPICAL RECESS INSTALLATION

LEVELING

SURFACE

WATERPROOF

SEALANT

BATH

WHIRLPOOL ONLY:

UNLESS AN ACCESS OPENING OF AT LEAST

12" X 24" (305 X 610MM) IS PROVIDED,

WARRANTY SERVICE WILL NOT BE PERFORMED.

TYPICAL PIER TYPE INSTALLATION

AS DESIRED

794mm

(31-1/4)

CUTOUT

AS DESIRED

464mm

(18-1/4)

ACCESS PANEL

610mm

(24)

305mm

(12)

610mm

(24)

305mm

(12)

464mm

(18-1/4)

464mm

(18-1/4)

1527mm

(60-1/8)

819mm

(32-1/4)

832mm

(32-3/4)

TUB WIDTH

LEVELING

STRINGERS

WHIRLPOOL ONLY:

UNLESS AN ACCESS OPENING OF AT LEAST

12" X 24" (305 X 610MM) IS PROVIDED,

WARRANTY SERVICE WILL NOT BE PERFORMED.

INSTALLATION AND FRAMING INSTRUCTIONS

The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs

as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an

access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for

access to the drain components.

NOTE: The apron should not be used as the primary access opening.

1. As shown in Fig. 1, mark the position of the underside of the deck by tracing a line onto the studs at the height indicated,

using a level or other suitable straight edge.

2. With the top of the 2 x 4 stringer touching the traced line, attach the stringer to the studs.

3. Install drain components to the whirlpool following the manufacturers instructions. Before replacing your whirlpool for final

installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing for

suggested opening size and location dimensions.

4. This bath must be supported along its entire bottom in all types of installations. We recommend the use of mortar or

plaster as bedding material (sand is not recommended). Apply enough bedding to support the complete bottom of the

bath. After the bedding has been poured, and before it sets, lower the bath into place until the rim is leveled against the

leveling stringers (see "Typical Installation Methods"). The rim of the bath MUST NOT support weight. Allow the bedding

material to completey harden before applying weight to the rim or bottom of the bath. Any finish material such as tile or

wall board must be self-supporting if it contacts the deck of the bath.

752445-100 Rev. E (2)

TILE

BEAD

STRIP

LEVELING

STRINGER

BATH

ADHESIVE

SEALANT

WALLBOARD

NOTE: Tile bead kit not included and must be

purchased separately.

FIG. 1

ELECTRICAL DIAGRAM

READ AND FOLLOW ALL INSTRUCTIONS

BLACK

WHITE

120 VAC

GND.

15 AMP

GFCI

OUTLET

WHIRLPOOL MOUNTED

AIR SWITCH OR

WALL TIMER

ELECTRICAL INSTALLATION

PUMP/MOTOR

752445-100 Rev. E

ELECTRICAL INSTALLATION INSTRUCTIONS

All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other

applicable codes.

WARNING:

When using electrical products, basic precautions should always be observed, including the following:

1. DANGER: RISK OF ELECTRIC SHOCK

Connect only to a circuit protected by a ground-fault circuit interrupter.

2. Grounding is required. The unit should be installed by a licensed electrician and grounded.

3. Install to permit access for servicing.

4. All building materials and wiring should be routed away from the pump body and heater (if equipped).

The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the

electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded

neutral wire and a third wire, earth ground, are essential.

(3)

WIRE SELECTION GUIDE

752445-100 Rev. E

DRAIN CONNECTION AND SYSTEM TEST

Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the

pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of

the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings

are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is

connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the

whirlpool is running.

POST INSTALLATION CLEAN-UP

Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.

Do not use wire brushes or any other metal implement on bath surface.

Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or

stains may be removed using granular Spic and Span

mixed with water.

Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.

HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.

Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing

with a white automotive-type polishing compound and waxing with a liquid wax.

Maximum distance from

fusebox to motor

The sizes shown on this

chart are recommendations

for copper conductors

only. Always follow

local and national

electrical codes

Motor

Hi-Performance

Rating

50' 100'

115V Power Line

150' 200'

12 12 10 8

1.1

(4)

SPIC AND SPAN

IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE

American Standard 2675018.222 User manual

American Standard 2675018.222 User manual

American Standard 2675018.222 User manual

Related papers

Other documents