Global Sat BU-353 User manual

Brand: Global Sat

Model: BU-353

Category: Navigators

Type: User manual

This manual is also suitable for

BU-303

USB GPS User’s Guide (WIN)

USB GPS Receiver

BU-303 (SiRF II)

BU-353 (SiRF III)

(Information on installation of the USB driver contained in this

document is also applicable to our USB cable set #BR305-USB)

DOCUMENTREVISIONS

REV NO. DATE DESCRIPTION APPROVED

1.2 02-28-2003 Initialdocument BRF

2.0 06-08-2005 Newdocumentformat NRG

2.1 04-07-2006 Revisionofembedded webinks AAK

of Globalsat Corporation. Windows is a register trademark of Microsoft Corporation. Acrobat is a registered

trademark of Adobe Systems Incorporated. Mac is a registered trademark of the Apple Corporation. All other

trademarks or registered trademarks are acknowledged as the exclusive property of their respective owners.

medium, for anypurpose, withoutprior written consent from GlobalsatTechnologyCorporation or USGlobalsat, Inc.

Globalsat/USGlobalsat hereby grants the right to download one (1) copy of this manual onto a hard drive for

personal use. This manual is copyrighted and may contain proprietary information that is subject to change without

notice.

PAGE2 OF 13

USB_GPS_WIN_v2.1

USB GPS (WIN)

Table of Contents

PACKAGE CONTENTS..................................................................................................3

SYSTEM REQUIREMENTS ...........................................................................................3

WELCOME......................................................................................................................3

1. GETTING STARTED..................................................................................................4

2. INSTALLING THE USB DRIVERTO YOUR LAPTOP..............................................4

3. COM PORT VERIFICATION......................................................................................5

4. INITIALIZING YOUR GPS RECEIVER......................................................................6

5. USING / TESTING YOUR GPS RECEIVER..............................................................6

6. UN-INSTALL THE USB DRIVER...............................................................................8

7. FAQ’s..........................................................................................................................8

8. CONTACT INFORMATION........................................................................................9

9. SAFETY AND LEGAL NOTICES...............................................................................9

10. LIMITED WARRANTY............................................................................................11

11. BU-303 SPECIFICATIONS....................................................................................12

12. BU-353 SPECIFICATIONS ....................................................................................13

PAGE3 OF 13

USB_GPS_WIN_v2.1

USB GPS (WIN)

PACKAGE CONTENTS

- USB GPS Receiver

- Driver CD-ROM with User’s Guide and test utilityfor WIN and Mac O/S*

 WIN Users please refer to the root directory on the included CD-ROM for installation instructions

and drivers.

NOTE: Your can also downloadWIN driver and Installation Guides at: www.usglobalsat.com/

SYSTEM REQUIREMENTS

The Globalsat USB GPS receivers requires a Windows, or Macintosh laptop computer, with a CD-

ROM*, USB port, and NMEA compatible navigation software. The 3

party mapping/navigation

softwaremayhave its own system requirements, please check with software vendorfor details.

*CD-ROM is required for USB driver installation and access to the User’s Guide. If no CD-ROM drive is available,

filescan bedownloaded fromthe Internetat: http://www.usglobalsat.com/

WELCOME

Thank you for purchasing a Globalsat USB GPS receiver! Globalsat USB GPS receivers allow for real-time street

navigationbyusingyour laptop for graphical plottingand positioning of your route. Simply load the GPS driver, plug

the GPS receiver into your computer’s USB port and install your own personal mapping software to begin to view

your position inreal-time in relation to thesurroundingstreets in your travelarea.

You’ll find that almost any NMEA compliant mapping/charting software will be compatible with your USB GPS

receiver. Visit our web-site for recommendedmappingprogramsthat you can use.

http://www.usglobalsat.com/faq_details/Mapchart.asp

PAGE4 OF 13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

1. GETTING STARTED

These areonly a few simple steps thatyou need tofollow beforeusingyour USB GPS receiver:

 Install the USB driver and onto your laptop from the included CD-ROMor download the files from our web-site

www.usglobalsat.com

 Plug-in theGPSreceiver into your laptop.

NOTE: From within your mapping, or navigation software (including the supplied GPS Information utility), you will

need to manually configure the selection of the COM port to what was assigned to the GPS receiver so that proper

communication between the GPS receiver and mapping program can occur. Most all software requires that you

manuallyconfigure the COMport setting for anyGPS device you use.

IMPORTANT:

1. You must change the default rate setting of your mapping software ‘s Baud Rate to 4800 if this is not currently

set assuch otherwise GPS data cannot be received.

2. Set Baud Rate 4800,Data Bit:8, Parity: None, Stop Bit: 1, Flow Control: None

2. INSTALLING THE USB DRIVER TO YOUR LAPTOP

1. Place the product CD-ROMinto your CD-ROM drive.

2. Auto-run should detect theCD bring up the followingscreen below.

PAGE5 OF 13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

3. Click on thebutton titled “Install Driver” from the main screen as shown above.

4. Or should your “Auto-Run” be disabled on your PC, use Windows Explorer or File Manager to

locate the file titled ”PL-2303 Driver Installer.exe” in the root directory of the CD-ROM and click to

launch the installprocess.

3. COM PORT VERIFICATION

1. Once your USB Driver has been installed, you will needto confirm which COM Port your PC

has assignedto it in orderto properly configure any software that will be utilizing the GPS data

being received.

2. Your USB GPS MUST be plugged into your USB port at this time.

3. UsingWindow’s Control Panel, select System > Hardware > Device Manager

4. Then look under the heading of: PORTS (Com & LPT)

5. There should be a listing for: Prolific Serial-to-USB Comm Port (COM x)

(“x” will actually be the number your PC has assigned the USB GPS receiver).

6. Once you have identified the COM port number, any softwarethat you utilize must be

configured to read GPS data from this COM port.

We stronglysuggest that youfirsttest your USB GPS with the included GPS Info utility program to

confirm that the GPS receiver if functioning properly on your PC and that youhave successfully

configured the right COM Port setting. Oncethishas been done, close the GPS Infoprogram and

start your application for COM port configuration.

NOTE: Bydefault, your PC will not allow you to run multiple applications from a single COM port. It

is important that you close any previouslyopened GPS application before switchingtoanother

GPS application as the GPS receiver and data will not be found by the new program.

There are special utilities available tosplit data into multiple COM ports for use by more than one

application simultaneously. (see: http://franson.com/gpsgate/ )

PAGE6 OF 13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

4. INITIALIZING YOUR GPS RECEIVER

Before using your USB GPS receiver for navigation (especially for the first time), the receiver must

obtain a local GPS fix (coordinates) of the current position. To do this, take your laptop (with your USB

driver and the mapping software loaded and configured) to an open area that has a clear view to the

sky (such as a park or empty field). Start your software (or the included GPS Info utility program) and

wait for initialization of the GPS to complete. This may take a few minutes depending on various

factors such as the distance of the current coordinates from the last time the GPS receiver was

activated, GPS signal strength and surrounding terrain (tall trees and buildings can block the satellite

signals). Once the RAW GPS data is displayed onto the screen, if applicable for your software, a fix

has been initialized (red LED on the GPS will also start to flash). In some cases initialization can take

up to several minutes depending on the conditions mentioned above before complete GPS data will be

displayed on the screen.

Coordinates scrolling with zero’s means thatthe port connectionis complete, but the satellite data is not

being received yet (possiblystill initializing or in a bad areafor satellite reception).

5. USING / TESTING YOUR GPS RECEIVER

Once the USB GPS receiver’s driver and your personal mapping software have been installed and

configured properly, you can begin to use your navigation system by plugging the USB GPS into your

laptop’s USB port and launching your mapping software. If you don’t have a mapping, or navigation

software, we’ve included a GPS test utility called “GPS Info” for the purpose of confirming your

installation and configuration. This utility can be installed by clicking the GPSInfo.exe file from the Win

directoryon theCD-ROM ordownloaded from our web-site www.usglobalsat.com.

LED Status indicator on the USB GPS”

LED OFF: GPS receiver is off (no power).

LED ON (solid): No fix, searching for GPS signals.

LED FLASHING: Position fix established and GPS signals are being received.

Always select an area in the vehicle where the GPS unit will be secure and not obstruct normal driving,

visibility and safety, but still maintaining a “view to the sky” in order to receive satellite data.

It isrecommended that you first load and test your GPS receiver with the GPSinfo.exe. This process

will confirm you have found correct COM port number and have configured it properly.

1. Run GPSinfo.exe to load the utility.

2. Enterthe proper COM portfor your GPS device (see COM Port Verification above)

3. Set COM port to Baud rate: 4800

4. If no errors have been made in configuration, there should be GPS data being displayed in the

window, which is confirmation that the communication between the GPS device and the “GPSinfo”

softwareisworking properly.

5. Ifthere is no GPS data displayed (or data with multiple zeros inthem), please exitthe software and

unplug the GPS receiver fromthe USB port andreinsertit after 10 secondsto reset the device.

PAGE7 OF 13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

The above screen shows the available satellites (numbers) and their signal strength.

NOTE: Configuration (or selection) of an assigned COM port for the GPS device from within your

mapping or charting software must be completed whenever using a software for the first time.

PAGE8 OF 13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

6. UN-INSTALL THE USB DRIVER

Run thefile the Remover98_2k.exe to uninstall theUSB GPS driver.

7. FAQ’s

I an not getting GPS data into my application.

1. Check your DEVICE MANAGER to confirm the COMPort number assigned to the GPS

Receiver (it will be listed under the PORTS (COM & LPT) heading as Prolific Serial-to-USB

Comm. Then besure this is the same COM port number configured in your application.

2. Be sure your Baud rate is configured correctly at:

Baud Rate: 4800

Data bit: 8

Parity: None

Stop Bit: 1

Flow Control: None

3. Re-boot your computerand then insertthe USB GPS into a USB port.

4. Configure the GPS Info utility with thecorrect COM Port and test your GPS receiver first

before using it in your application.

Will the USB GPS work with other Street Mapping software?

Globalsat USB GPS receivers provides standard NMEA data for mapping software to use and convert

to coordinates and should work well with most any NMEA compliant software on the markettoday.

How accurate is the GPS?

The USB GPS is WAAS/EGNOS capable, and forunits sold in North America throughauthorized

resellers, these units areWAAS/EGNOS enabled unless otherwise stated. Accuracy can be upto5

meters3D RMS withWAAS enabled and 10-15 meters 2D RMS WAAS disabled

What is ideal GPS environment?

The GPS requires an open, clear view of the sky. Buildings, covered parking areas,tunnels and dense

foliage can causethe GPS receiver to beunable to get a location fix.

If you are parked in a covered parkinglot or near a tall building, it is recommended that you drive away

until you have a clear viewof the sky beforeusingthe BU-303. You may need to givethe GPS a few

minutes to find or get a fix its location.

How do I know if the GPS is ON?

Your USB GPS must be plugged into your laptop’s USB port to get power. If your PC is on andthe

COM port wasconfigured properly, the GPS receiver is onand receivingthe streaming GPS data. This

can be verified by openingyour mapping software program. In addition, the GlobalsatUSB GPS hasa

built-in LED status indicator that shows the following:

LED OFF: GPS receiver is off (no power).

LED ON (solid): No fix, searching for GPS signals.

LED FLASHING: Position fix established and GPS signals are being received.

PAGE9 OF 13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

Whydoes the GPS not work near buildings and other tall objects?

The GPS uses satellites inthe space to find out where it is. Therefore it needs a clear view of the sky.

Tall buildings and other objectsthat block the receiver’sview to thesky make it infeasible to determine

your location. Sometimes the satellites are not overhead but near the horizon. Inthese cases the GPS

must have aclear view of the horizon.

Other Comments-

Please allow an adequate amount of time for the GPS receiver’s boot-up (TTF) to complete before

contacting Technical Support.

Driver updates can be found at Prolific ’s web-site:

http://www.prolific.com.tw/eng/downloads.asp?ID=31 (www.prolific.com.tw)

8. CONTACT INFORMATION

Globalsat Technology Corporation (Taiwan)

www.globalsat.com.tw

service@globalsat.com.tw (pre-sales GPS product questions only)

USGlobalsat, Inc.

www.usglobalsat.com

sales@globalsat.com (pre-sales GPS product questions only)

Technical Support (North America)

See our DOWNLOADS andFAQ section onour web-site for GPSsolutions, driver literature updates.

http://www.usglobalsat.com/custom.asp?recid=7

Pre-registration is required before receiving any type of technical support. Support issues submitted via

phone, fax or e-mail(any means outside of therecognized “Trouble Ticket” generatedfrom your own

USGlobalsat registered account) WILL NOT be answered.

Create your account and register your products at: www.usglobalsat.com/support/custadminlogin.asp

9. SAFETY AND LEGAL NOTICES

Please read this section carefully before using the GPS receiver

Globalsat Technology Corporation / USGlobalsat, Inc. will not accept any responsibility

whatsoever for accidents resulting from failure to observe common sense precautions. Your

personal judgment, traffic regulations, and common sense must always take precedence over

any directions produced by GPS receiver or the mapping software

WARNING: Make sure that the GPS receiver is secure and does not interfere with driving

visibility and safety.

It is your responsibility as the vehicle operator to securely place the GPS unit and antenna so that they

will not interfere with driving and prevent operations of any safety device (such as the Airbag) in your

vehicle. Do not mount the devices in a place where the driver or passengers may receive injury during

vehicle operation or collision. For your safety, take care to route all cables away from shifters, pedals,

accessory controls and mechanisms.

PAGE10OF13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

WARNING: Drive safely and use common sense.

It is your responsibility as the vehicle operator to drive safely, observe all traffic rules and above all use

your own personal judgment while driving. If you feel that a route suggested by the navigation software

instructs you to perform an unsafe or illegal maneuver, places you in an unsafe situation, or routes you

into an area which you consider unsafe, do not follow theinstructions.

WARNING: Keep your eyes on the road.

It isyour responsibility as the vehicle operator to keep your eyesonthe road and be an alert driver at all

times, especially when the vehicle is moving. The vehicle’s operator should not be distracted by the

navigation equipment or software. Should there be a distraction with the ability to drive responsibly,

please turn off the device. Should you want to look at the display for a prolonged time, park the car

safely, while following all traffic regulations before looking at the display.

WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or

moisture. Do not remove covers or open housings, there are no user serviceable parts inside.

Refer servicing to qualified personnel only.

PAGE11OF13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

10. LIMITED WARRANTY

Globalsat/USGlobalsat warrants product hardware against manufacturing defects in material and workmanship

under normal use for a period of one (1) year from the original date of purchase (unless the product states

otherwise), and only when purchased from a recognized “authorized dealer”. Products purchased from any

unauthorized source, such as unauthorized e-Bay resellers, will not qualify for free warranty service/support and

may require the end-user to pre-pay fees associated with, but not limited to the support, repair, replacement and

shippingof the product to and from theservice center.

Except as provided herein, Globalsat/USGlobalsat makes no express warranties’, including but not limited to any

warranties of merchantability or fitness for particular use, or non-infringement. You acknowledge that your use of

the product or service is at your sole risk and you agree that the information provided are without warranty of any

kind by Globalsat/USGlobalsat.

Under no circumstances, including negligence, will Globalsat/USGlobalsat or any of its affiliates, directors, officers

or employees, or any third party be liable for any direct, indirect, incidental, special or consequential damages that

results from your use, or your inability to use, or the performance of the product(s) with respect to any liability, loss,

orarising outof anybreach of thiswarranty, including, but not limited to anydamages resultingfrom inconvenience,

loss of time, data, property, revenue, or profit or any indirect, special incidental or consequential damages. You

acknowledge that this limitation applies to all content information or other services available from

Globalsat/USGlobalsat, and whether or not Globalsat/USGlobalsat has notice of the possibility of such damages,

and whether or not to circumstances giving rise to such damages may have been within the control of

Globalsat/USGlobalsat.

Some states do not allow the exclusion of certain warranties, so some of the above exclusions may not apply to

you. In those states, liability is limited to the fullest extent allowed by law By using the product(s), you agree to

indemnify Globalsat/USGlobalsat and its parents, subsidiaries, affiliates, officers and employees and hold them

harmless from any and all claims and expenses, including reasonable attorney’sfees, asserted third party dueto, or

arising out of youruse of the service and the site.

In the event of a product defect during the first 30-days of the warranty period, return product and the sales receipt

asproof of purchasedate to placeof original purchase. Defect discovered after30-days from date of purchase, you

mustcontact Globalsat/USGlobalsat’s Technical support for a ReturnMerchandise Authorization (RMA)number for

return to manufacturer.

Globalsat/USGlobalsat will,at its option, unless otherwise providedbylaw:

a.) Correct the defect byproductrepairwithoutchargefor parts and labor;

b.) Replace the productwith one of the sameor similar design; or

Refund the purchase price. All replaced parts and products, and products on which a refund is made, become the

property of Globalsat/USGlobalsat. New or reconditioned parts may be used in the performance of warranty

service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period.

You willbe chargedforrepairor replacementof the product made after the expiration of the warranty period.

This warranty does not cover:

a.) Damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or

abnormal usage, failure to follow the instructions, improper installation or maintenance, alteration, lighting

orotherincidenceof excessvoltage orcurrent;

b.) Anyrepairs otherthan those provided by Globalsat/USGlobalsat;

c.) Consumablessuchas fusesor batteries;

d.) Cosmetic damage;

e.) Transportation,shippingor insurancecosts;

f.) Costs of product removal,installation, set-upserviceadjustmentor reinstallation.

This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to

state.

Additional products bundled in this package not manufactured by Globalsat/USGlobalsat will hold separate

warranties as expressed by the individual manufacturer of that product(s). Product specifications, functions and

features are subject tochangewithoutnotice.

PAGE12OF13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

11. BU-303 SPECIFICATIONS

Electrical Characteristics (Receiver)

GPS Chipset SiRFStar IIe/LP

Frequency L1, 1575.42 MHZ

C/A Code 1.023MHzchip rate

Channels 12 all-in-view tracking

Sensitivity -147 dBm

Accuracy

Position Horizontal

10m 2D RMSWAAS enabled

15m 2DRMS WAAS disabled

Velocity 0.1m/sec 95% (SA off),

Time 1 micro-secondsynchronized to GPS time

WAAS Enabled forNorth Americaproducts (USGlobalSat, Inc)

Datum

Datum WGS-84

Acquisition Rate

Hot start 8 sec., average (with ephemeris and almanacvalid)

Warmstart 38sec.,average (withalmanac but not ephemeris)

Coldstart 45sec., average (neitheralmanac nor ephemeris)

Reacquisition 0.1 sec.average (interruption recovery time)

Protocol

GPS Protocol Default: NMEA 0183 (Secondary: SiRF binary)

GPS Output Data

SiRFbinary >> position, velocity, altitude,status andcontrol

NMEA 0183MEA0183 V2.2 protocol, and supports

command: GGA,GSA,GSV, RMC, VTG,GLLv2.2 (VTG

and GLL are optional)

GPS transfer rate Softwarecommandsetting (Default: 4800,n,8,1forNMEA)

Dynamic Condition

AccelerationLimit Less than 4g

Altitude Limit 18,000 meters (60,000feet) max.

VelocityLimit 515 meters/sec. (1,000 knots) max.

Jerk Limit 20m/sec**3

Temperature

Operating -40°~ 176°F (-40°~80°C)

Storage -40°~ 176°F (-40°~80°C)

Humidity Up to95% non-condensing

Power

Voltage 5V±5%

Current 90mAtypical

Physical Characteristics

Dimension 2.32" x1.65" x 0.82" (59mm x47mm x21mm)

USB Cable Length 60" (152 cm)

Low Noise Amp

Amplifier Gain w/out cable 27 dB Typical

Filtering -25dB(+100MHz)

Output VSWR 2.0 Max.

Voltage DC3 ~ 5.0V

Current 15mA max @ 5VDC

Due to continuous productimprovements,allspecifications aresubjectto change without notice.

FCC NOTICE

Thisdevice complies with part15ofthe FCCrules. Operationissubjecttothefollowingtwoconditions:

(1) This devicemay notcauseharmfulinterference, and(2)This devicemustacceptanyinterference received,includinginterference that maycause

undesiredoperation. FCCRFExposurerequirements: Thisdevice and itsantenna(s)must not be co-locatedoroperationinconjunction withany other

antennaor transmitter. NOTE:THEMANUFACTURERISNOTRESPONSIBLE FOR ANY RADIO ORTV INTERFERENCECAUSEDBY

UNAUTHORIZED MODIFICATIONSTO THISEQUIPMENT.SUCH MODIFICATIONS COULDVOID THEUSER'SAUTHORITYTO OPERATE

THE EQUIPMENT.

PAGE13OF13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

12. BU-353 SPECIFICATIONS

Electrical Characteristics (Receiver)

GPS Chipset SiRFStar III e/LP

Frequency L1, 1575.42 MHZ

C/A Code 1.023MHzchip rate

Channels 20 all-in-view tracking

Sensitivity -159 dBm

Accuracy

Position Horizontal

5m2D RMS WAAS enabled

10m 2DRMS WAAS disabled

Velocity 0.1m/sec 95% (SA off),

Time 1 micro-secondsynchronized to GPS time

WAAS/EGNOS Enabled forNorth Americaproducts (USGlobalSat, Inc)

Datum

Datum WGS-84

Acquisition Rate

Hot start 1 sec., average (with ephemeris and almanacvalid)

Warmstart 38sec.,average (withalmanac but not ephemeris)

Coldstart 42sec., average (neitheralmanac nor ephemeris)

Reacquisition 0.1 sec.average (interruption recovery time)

Protocol

GPS Protocol Default: NMEA 0183 (Secondary: SiRF binary)

GPS Output Data

SiRFbinary >> position, velocity, altitude,status andcontrol

NMEA 0183MEA0183 V2.2 protocol, and supports

command: GGA,GSA,GSV, RMC, VTG,GLLv2.2 (VTG

and GLL are optional)

GPS transfer rate Softwarecommandsetting (Default: 4800,n,8,1forNMEA)

Dynamic Condition

AccelerationLimit Less than 4g

Altitude Limit 18,000 meters (60,000feet) max.

VelocityLimit 515 meters/sec. (1,000 knots) max.

Jerk Limit 20m/sec**3

Temperature

Operating -40°~ 185°F (-40°~85°C)

Storage -40°~ 185°F (-40°~ 85°C)

Humidity Up to95% non-condensing

Power

Voltage 4.5 ~ 5.5V DCInput

Current 80mAtypical

Physical Characteristics

Dimension 2.08" diameter x0.75" (53mm dia.x 19.2mm)

USB Cable Length 60" (152 cm)

Low Noise Amp

Amplifier Gain w/out cable 27 dB Typical

Filtering -25dB(+100MHz)

Output VSWR 2.0 Max.

Voltage DC3 ~ 5.0V

Current 15mA max @ 5VDC

Due to continuous product improvements, all specifications are subject to change without notice.

FCC NOTICE

Thisdevice complies with part15ofthe FCCrules. Operationissubjecttothefollowingtwoconditions:

(1) This devicemay notcauseharmfulinterference, and (2) Thisdevicemust acceptanyinterference received, includinginterference thatmaycause

undesiredoperation. FCCRFExposurerequirements: Thisdeviceanditsantenna(s)mustnot beco-locatedoroperationinconjunction withanyother

PAGE14OF13

USB_GPS_WIN_ v2.1

USB GPS (WIN)

antennaor transmitter. NOTE:THEMANUFACTURERISNOTRESPONSIBLEFOR ANYRADIOORTV INTERFERENCECAUSED BY

UNAUTHORIZED MODIFICATIONSTO THISEQUIPMENT.SUCH MODIFICATIONS COULDVOID THEUSER'SAUTHORITYTO OPERATE

THE EQUIPMENT.

Global Sat BU-353 User manual

Brand: Global Sat

Model: BU-353

Category: Navigators

Type: User manual

This manual is also suitable for

BU-303

Download PDF

report

Global Sat BU-353 User manual

This manual is also suitable for

Global Sat BU-353 User manual

Other documents