Samsung SNC-M300P User manual

Category
Supplementary music equipment
Type
User manual

This manual is also suitable for

SNC-M300
SNC-M300
user manual
ENG TUR CZE
imagine the possibilities
Thank you for purchasing this Samsung product. To receive
more complete service, please register your product at
www.samsung.com/global/register
Cover-SNC-M300-AB68-00721F.indd 1 2008-07-14 오후 5:59:13
safety precautions
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)NO USER-SERVICEABLE PARTS
INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this
unit.
This symbol indicates that there are important operating and maintenance instructions in the literature
accompanying this unit.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
The camera is to be only connected to PoE networks without routing to the outside plant.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5.
When installing the camera, fasten it securely and firmly. A falling camera may cause personal
injury.
6.
Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers
filled with water on top of the camera. Doing so may cause personal injury due to fire, electric
shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric
shock.
EU-SNC-M300-ENG.indd 2 2008-07-14 오후 3:36:12
8. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued use in
such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disassemble
or modify this product in any way. (SAMSUNG is not liable for problems caused by
unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire
or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location
subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 122°F), low temperature (below
14°F), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so
may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6.
Install it in a place with good ventilation.
7.
Avoid aiming the camera directly towards extremely bright objects such as sun, as this may
damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
EU-SNC-M300-ENG.indd 3 2008-07-14 오후 3:36:13
important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
8
. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9
. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11
. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus.
13
. Unplug this apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
14
. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,
or been dropped.
EU-SNC-M300-ENG.indd 4 2008-07-14 오후 3:36:13
Contents _01
contents
Preparation
03
Installation and Connection
08
Network Connection & Setup
17
Setting Static IP
22
Setting Dynamic IP
26
03 Features
03 Precautions – Installation and Use
04 Recommended PC Specifications
04 Compatible IP Routers
04 Compatible PoE Switches
04 Checking the components in the package
05 Names of each part
08 Installing the Camera
12 Connecting
18 Connecting the camera to an IP router with
local area networking
20 Connecting the camera directly to local area
networking
21 Searching for the camera
22 Manual Network Setting
25 Automatic Network Setting
26 Dynamic IP Setting
27 Port Forwarding (Port Mapping) Setting
EU-SNC-M300-ENG.indd 1 2008-07-14 오후 3:36:13
02_ Contents
Using the Camera
28
Setting Up
41
Appendix
64
28 Connecting to the camera
30 Installing ActiveX
32 Using the Viewer Screen
36 Using the Search Viewer Screen
41 Setting the camera
43 Basic Configuration
49 System configuration
54 Layout Configuration
55 Event Configuration
62 Network Configuration
64 Troubleshooting
66 Specifications
EU-SNC-M300-ENG.indd 2 2008-07-14 오후 3:36:13
Preparation _03
01 PREPARATION
FEATURES
Various Communication Protocol Support
This product supports various communication protocols such as ARP, HTTP and DHCP as well as
TCP/IP, UDP, SMTP for Email transmission and FTP protocol.
Monitoring Through
Web Browser
Monitoring Through Web Browser This product enables watching a video through an Internet web
browser so that you can watch a video through the Internet as you can within the local network.
Automatic Local IP Setting Function
This function offers an easy way of configuring the network settings with a minimal key input for
those who are not familiar with it.
Alarm Function
If this product is connected with a motion sensor and the sensor detects a motion, a recorded
video clip is sent through the FTP/Email(SMTP) registered by the user or saved on the SDHC
memory card and a signal is sent to an alarm output port.
Motion
Detection Function
If the user specifies a target area to monitor and the motion sensor detects a motion within that
area, a still image is sent to the FTP/Email(SMTP) server designated by the user or saved on the
SDHC memory card, and signals are sent to the alarm output terminal.
PRECAUTIONS – INSTALLATION AND USE
Do not disassemble your camera.
Always be cautious when handling your camera.
Do not subject the camera to impact or vibration and always be cautious of damaging the camera
due to neglectful storage and/or operation.
Do not install the camera at a location where it would become exposed to rain or humidity and do
not operate the camera in a wet environment.
Do not clean the camera’s main body using harsh abrasives or similar substances. If dirty, use a dry
piece of cloth to clean instead.
Install the camera in a shaded area or environment, protected from direct sunlight.
Direct sunlight exposure has a negative effect on the camera.
Do not bend or throw the SDHC memory card.
Do not store or use the SDHC memory card in a hot, humid, or dusty environment.
Protect the contacts of the SDHC memory card from foreign substance buildup.
If foreign substances have been built up on the contacts, remove using a soft piece of cloth.
When removing the SDHC memory card, disable SD Card Recording to protect against data loss
(refer to page 57 for instruction on disabling SD Card Recording).
Data cannot be stored on SDHC memory cards whose service life has expired.
Please purchase a new SDHC memory card if you experience this.
The manufacturer will not be held responsible for data loss incurred by the customer due to im-
proper use.
Using non-recommended PoE device may cause malfunction of either the camera or PoE device
itself. (Refer to page 4 for the compatible PoE Switch)
preparation
EU-SNC-M300-ENG.indd 3 2008-07-14 오후 3:36:13
04_ Preparation
RECOMMENDED PC SPECIFICATIONS
CPU: Pentium4/2.4GHz or higher
Operating System: Windows XP(Service Pack2) / Windows Vista
Resolution: 1024X768 pixels or higher
RAM: 512MB or higher
Web
Browser:
Internet Explorer 6.0 or higher
Video Card:
Radeon, Nvidia
Video Memory:
128MB
DirectX 8.1 or higher
COMPATIBLE IP ROUTERS
Linksys
D-Link
Netgear
COMPATIBLE POE SWITCHES
Linksys SRW224G4P
D-Link DES-1316
SMC SMCPWR-INJ3
CHECKING THE COMPONENTS IN THE PACKAGE
Make sure that the following items are included in the package.
Camera
User's Manual
C Mount Adapter
Auto Iris Lens Connector
Options
Software CD CS Lens C Lens
EU-SNC-M300-ENG.indd 4 2008-07-14 오후 3:36:13
Preparation _05
01 PREPARATION
NAMES OF EACH PART
Front
1
Back Focus Adjustment Bar
Adjust Back Focus by moving this bar up or down.
When the camera lens becomes dirty, softly clean it with a lens tissue or a cloth soaked in pure
ethanol.
1
EU-SNC-M300-ENG.indd 5 2008-07-14 오후 3:36:13
06_ Preparation
Rear
1
Audio Out For outgoing audio signals.
2
Audio In For incoming audio signals.
3
SDHC Memory Card Slot This is where you insert your SDHC memory card.
4
System, SD, and Power
Indicators
These indicators provide system, SD, and power status
information.
5
I/O Port
Used to connect the camera to an external device.
A_IN 1 and 2: These are alarm in ports.
GND: This is the GND port.
A_OUT 1 and 2: These are alarm out ports.
NOT USED: This port is not used.
6
Reset Button
Reverts all camera settings to their default.
When it is pressed for 3 seconds, the system indicator goes
out and the system reboots.
When the camera is reset, connection is possible only after the
basic network settings (IP address, subnet mask, gateway, etc.)
have been configured again using the IP installer program.
7 86 5
4
3
2
1
EU-SNC-M300-ENG.indd 6 2008-07-14 오후 3:36:14
Preparation _07
01 PREPARATION
7
Ethernet Port
Ethernet cable port.
8
Power Port
Connect the power cable to this port.
LED
Status
Description
SYSTEM
Turns on
When the power is switched on and the
network connection is normal.
Flashes
When the DDNS setting fails.
When the DDNS is being set.
When the network connection is not
stable.
Turns off
When the power is switched off.
When the camera is rebooting.
SD
Turns on
When the memory card is inserted and
the system is in normal operation.
Flashes
When recording fails.
When the memory card is short of
capacity.
When the memory card is not inserted
normally.
Turns off
When the power is switched off.
When the camera is rebooting.
When the memory cared is removed.
PWR
Turns on When the power is switched on.
Turns off When the power is switched off.
EU-SNC-M300-ENG.indd 7 2008-07-14 오후 3:36:14
08_
Installation and Connection
INSTALLING THE CAMERA
Disconnect the power cord before installation or relocation.
Mounting the lens
When using the CS lens
Mount the CS lens by rotating it clockwise as shown in the picture.
When using the C lens
After mounting the C-mount adapter by rotating it clockwise, turn the C lens clockwise until it
is fixed as shown in the picture.
installation and connection
CS lens
C lens
EU-SNC-M300-ENG.indd 8 2008-07-14 오후 3:36:14
Installation and Connection
_09
02
INSTALLATION AND CONNECTION
Adjusting the back focus
The back focus of the camera is adjusted at the factory before delivery but some lenses can
be out of focus depending on the lens type. In this case, you have to adjust the back focus.
The following describes how to adjust the back focus of the lenses.
In case of the lens with no zooming function
1
After exposing the camera to an object with high resolution (like a dart-patterned image)
at a distance of more than 10m, set the lens focus ring to infinite (
).
2
Adjust the Back Focus Control Bar until the object is of best quality.
3
Fix the screw of the Back Focus Control Bar.
In case of the lens with zooming function
1
After exposing the camera to an object with high resolution (like a dart-patterned image)
at a distance of 3 to 5m, fully rotate the lens zoom to the TELE direction.
Then adjust the lens focus ring until the object is of best quality.
2
Fully rotate the lens zoom to the WIDE direction and adjust the Back Focus Control Bar
until the object is of best quality.
3
Repeat step 1 and 2 two or three times until the focuses of Zoom TELE and Zoom WIDE
are clear enough.
EU-SNC-M300-ENG.indd 9 2008-07-14 오후 3:36:14
10_
Installation and Connection
Inserting/Removing an SDHC Memory Card
Inserting an SDHC Memory Card
Push the SDHC memory card in the direction of the arrow shown in the diagram.
Do not force the memory card in. If you can’t insert the memory card into the slot with ease,
you might be inserting the card in the wrong direction. Forcibly inserting a memory card could
lead to its damage.
Removing an SDHC Memory Card
Gently press down on the exposed end of the memory card as shown in the diagram to eject
the memory card from the slot.
Pressing too hard on the SDHC memory card can cause the card to shoot out uncontrollably
from the slot when released.
When removing the SDHC memory card, disable the SD Card Recording feature (refer to
page 57 for instructions on disabling SD Card Recording).
Removing the SDHC memory card while recording is in progress can damage the data.
NA-M300-ENG_AB68-00721A.indd 10 2008-08-01 오전 11:25:24
Installation and Connection
_11
02
INSTALLATION AND CONNECTION
Memory Card Information (not included)
What is a memory card?
The memory card is an external data storage device that has been developed to offer an entirely
new way to record and share video, audio, and text data using digital devices.
Selecting a memory card that’s suitable for you
Your camera supports SDHC memory cards.
You may, however, experience compatibility issues depending on the model and make of the
memory card.
Your camera supports SD memory cards.
However, the maximum supported SD memory card capacity is 2GB and ver 1.1, 4GB or
above SD memory cards are incompatible.
For your camera, we recommend you use a memory card from the following manufacturers:
SDHC/SD Memory Card: Panasonic®, SanDisk®, and Toshiba®
Your camera supports 128MB to 16GB of memory card capacity.
Playback performance can be affected depending on the read/write speed of the memory card,
so use a high-speed memory card. We recommend you use a memory card with a read/write
speed of at least 10Mbps and Class 6 specifications.
Memory Card Use
SD and SDHC memory cards feature a switch that disables writing data on to the media.
Having this switch to the Lock position will prevent accidental deletion of data stored in the
memory card but at the same time will also prevent you from writing data on to the media.
Me
mo
ry Card Components
SDHC
Lock Switch
Contacts
EU-SNC-M300-ENG.indd 11 2008-07-14 오후 3:36:14
12_
Installation and Connection
CONNECTING
Connecting Ethernet Cable
Connect the Ethernet cable to the network port as shown.
EU-SNC-M300-ENG.indd 12 2008-07-14 오후 3:36:15
Installation and Connection
_13
02
INSTALLATION AND CONNECTION
Connecting Power
1
Connect the power adapter to the camera’s power port.
2
Using a flathead screwdriver, connect the two lines leading from the power adapter to the
cameras power port.
3
Connect the power cord to the power adapter unit.
4
Connect the power plug to a power outlet.
Beware of DC 12V’s polarity charges when making the connection.
If you are using a PoE (Power over Ethernet) supporting router, you do not need a separate
power source.
EU-SNC-M300-ENG.indd 13 2008-07-14 오후 3:36:15
14_
Installation and Connection
To connect input and output ports:
Connect alarm lines to the input and output ports on the rear.
A_IN 1, A_IN 2 :
T
hese are alarm in ports.
GND : This is the GND port.
A_OUT 1, A_OUT 2 : These are alarm out ports.
Alarm In/Out Connection Diagram
1
A_IN1
A_OUT1
A_OUT2
Not Used
A_IN2
GND
2
3
4
5
6
External Relay
External Relay
EU-SNC-M300-ENG.indd 14 2008-07-14 오후 3:36:15
Installation and Connection
_15
02
INSTALLATION AND CONNECTION
Connecting to Audio Input/Output
1
Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT
port of the amplifier that the microphone is connected to.
Direct Mic Connection: Set Audio Input Gain high (10). (Refer to page 43)
Line Out Connection: Set Audio Input Gain low (1). (Refer to page 43)
2
Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker.
Microphone
Pre-Amp
Speaker
LINE-IN
Pre-Amp
Microphone
LINE-OUT
EU-SNC-M300-ENG.indd 15 2008-07-14 오후 3:36:15
16_
Installation and Connection
Audio I/O Block Diagram
Speaker
Pre-Amp
Microphone
PC
Audio Codec
G.711 PCM, μ-law 64kbps 8kHz sampling
Full duplex Audio
Audio in
Used for mono signal line input (Max.2.4 Vpp)
Audio out
Used for mono signal line output (Max.2.4 Vpp)
Li
ne
out impedance
600ohm
Pre-Amp
Microphone
EU-SNC-M300-ENG.indd 16 2008-07-14 오후 3:36:15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260

Samsung SNC-M300P User manual

Category
Supplementary music equipment
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI