5019 312 11074
Whirlpool is a registered trademark of Whirlpool USA.
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
without“Rapid”
(kWh)
Approx.ProgrammeDuration(hrs:min)
without“Rapid” with“Rapid”
Cotton/Antibacterial 95 6.0 53* 1.91 2:05 –
Cotton** 60 6.0 48 1.02 4:00 2:30
Cotton** 60 3.0 35 0.76 2:10 ***
Cotton 40 6.0 48 0.65 2:50 2:00
Cotton** 40 3.0 35 0.57 2:00 ***
SuperEco 60 6.0 55 0.78 4:00 –
Synthetics 60 3.0 50* 0.90 2:05 1:14
Synthetics 40 3.0 40 0.50 1:50 0:59
Delicates 40 1.5 50 0.55 0:45 –
Dailyload 40 3.0 40 0.45 1:00 –
Speed15´ 30 3.0 30 0.15 0:15 –
Wool 40 1.0 55 0.55 0:45 –
Handwash 40 1.0 40 0.55 0:35 –
Lingerie 30 1.0 40 0.40 0:31 –
CONSUMPTION DATA
1. Loadthemachine,closethedrumdoorsandcheck
thattheyareproperlylocked.
2. Adddetergentandeventualadditivesasdescribedon
thefrontpageandinyourInstructionsforuse.
3. Closethelid.
4. Turntheprogramme selectortothedesired
programmeandtemperature.Thetimedisplay
showsthedurationofthechosenprogramme(in
hoursandminutes),andthelampnexttothe“Start
(Pause)”buttonflashes.Theindicationlampofthe
predefinedspinspeedlightsup.
PREPARATION OF THE WASH CYCLE
“DOOR OPEN” INDICATION
Beforestartingandafterendofaprogramme,thelamp
lightstoshowthethelidcanbeopened.Aslongasa
washprogrammeisrunning,thelidremainslockedand
mustonnoaccountbeforcedopen.Incaseyouhave
anurgentneedtoopenitduringarunningprogramme,
referto“Cancel(Reset)arunningprogrammebefore
theend”.
“Rapid” button
• Enablesquickerwashingbyshorteningthe
programmeduration.
• Recommendableforsmallloadsoronlylightlysoiled
laundry.
“Prewash” button
• Onlyforheavilysoiledloads(forexamplesand,
granulardirt).Increasesthecycletimeby
approximately20min.
“Intensive rinse” button
• Theamountofwaterisincreasedtoensureamore
intensiverinse.
• Thisoptionisparticularlysuitableforareaswithvery
softwater,washingbabylinenandpeoplewithskin
allergies.
“Rinse hold” button
• Thelaundryremainsinthelastrinsewaterwithout
progressingtothefinalspincycletoavoidcreasing
andpreventcoloursfromchanging.
• Thisoptionisparticularlyrecommendedforthe
“Synthetics”,“Dailyload”and“Delicates”
programmes.
• Itisusefulifyouwanttopostponespinningtoalater
time,orifyouwanttodrainoutonly.
• Ifyouselect“Rinsehold”,donotleaveitemsto
soakfortoolong.
• Assoonastheappliancestopsintherinsehold,the
“Rinsehold”lampofthesequenceindicatorlightsup
andthelampnexttothe“Start(Pause)”buttonflashes.
Terminate the “Rinse Hold” option:
• Pressthe“Start(Pause)”button;theprogramme
willterminateautomaticallywiththefinalspincycle
forthepresentwashprogramme.
• Ifyoudonotwishtospintheclothes,turnthe
programmeselectorknobtothe“Drain”
programmeandpressthe“Start(Pause)”button.
PROGRAMME START
Openthetapandpressthe“Start(Pause)” button.
Theindicationlampnexttothe“Start(Pause)” button
lightsup.Theprogrammesequenceindicatorshowsthe
currentprogrammephase,runningfromlefttoright
throughWash,Rinse,Spin/Drain.Whentheprogramme
phraseisfinised,thecorrespondingindicationgoesout.
• Note: Ifthereisapowerinterruptionorifthe
applianceisdisconnectedduringthecycle,the
programmewillrunagainfromthepointwhereit
wasinterrupted.
PROGRAMME END
• Allthelightsoftheprogrammesequenceindicator
areoff,andthe“Dooropen”indicationlightsup.
1. Turntheprogrammeselectortothe“Off/O”
position.
2. Closethewatertap.
3. Openlidanddrumandunloadthemachine.
4. Leavethelidopenforsometimetoallowthe
interiorofthemachinetodry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Pressthe“Start(Pause)” buttontopausethe
programme.Thelightflashes.
2. Selectthenewprogramme,anyoptionsandanother
spinspeedifyouwant.
3. Pressthe“Start(Pause)” buttonagain.Thenew
programmecontinuesatthesamepositionwhere
thepreviousprogrammewasinterrupted.Donot
adddetergentforthisprogramme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The“Reset”buttoncancelsaprogrammebeforethe
end.Pressthe“Reset” buttonforatleast3seconds.
Anyexistingwaterisdrainedoutbeforethelidcanbe
opened.
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been executed yet.
“Clean+” button
• Choosethisoptionifyouuseanin-washadditivefor
stainremoval(powder,forexample“Vanish”)-it
willoptimizetheadditive’sefficiencytogetbetter
washperformanceandstainremoval.
• Selectableforprogrammes“Cotton”and
“Synthetics”;choosetemperatureof30or40°Cand
usewithmaximumload.
• Addanappropriateamountofin-washadditivefor
stainremoval(powder)tothemainwashchamber,
togetherwithyourdetergent(onlyusepowder
detergentwiththisoption).Respectthe
manufacturer’sdosinginstructions.
• Prolongstheprogrammebyapprox.10to15minutes.
• Appropriateforuseofstainremoversandbleaches
onoxygenbasis.Chlorine or perborate bleaches
must not be used!
START DELAY
The“Startdelay”buttonallowstheusertorunthe
machineathisconvenience,forexampleatnightwhen
electricityischeaper.
• Selectprogramme,spinspeedandoptions.
• Pressthe“Startdelay”buttonseveraltimesto
selectadelaytimeby1to23hours.
• Startthecountdownofthe“Startdelay”bypressing
“Start(Pause)”.thelampoverthe“Startdelay”button
blinks,anditgoesoffwhentheprogrammestarts.
• Oncehavingpressedthe“Start(Pause)”button,
thecountdownofthetimedelaybegins.Thetime
delayindicationonthedisplaydisappearswhenthe
programmestartsandisreplacedbytheremainingtime.
• Afterthe“Start(Pause)”buttonhasbeenpressed,
thenumberofhourspreselectedcanbereducedby
pressingagainthe“Startdelay”button.
To cancel the “Start delay”
..before you press the “Start(Pause)” button:
• Turntheprogrammeselectortoanotherposition
orpressthe“Reset”button.
..after having pressed the “Start(Pause)” button:
• Pressthe“Start(Pause)”button-thedelaytime
disappearsfromthedisplay.
“Variable spin” button
• Everyprogrammehasapredefinedspinspeed.
• Pressthebuttontosetanotherspinspeed.
• Ifspinspeed“0”isselected,thefinalspinningis
cancelledbutintermediatespinpeaksremainduring
therinse.Thewaterisdrainedoutonly.
FAILURE INDICATIONS
Incaseofanyfailuresorirregularities,consultthe
“TroubleshootingGuide”inyourInstructionsforUse.
“Service”
Lightingupofthe“Service”indicationcanbecaused
byafaultinanelectricalcomponent.Refertothe
“TroubleshootingGuide”inyour“InstructionsforUse”;
ifthefaultpersists,contactourAfterSalesService.
“Water tap closed”
Theappliancehasnoorinsufficientwatersupply.Open
thewatertap:iftheindicationsstilllightsup,refertothe
“TroubleshootingGuide”intheInstructionsforUse.
“Clean pump”
Wastewaterisnotpumpedout.Checkwhetherthe
drainhoseiskinkedorthefiltermustbecleaned:inthe
lattercaserefertotheInstructionsforUse(“Removing
theFilter”).
ConsumptionvaluesweremeasuredinnormalizedconditionsincompliancewithstandardIEC/EN60456.Consumptiondatainthehomemayvarywith
respecttothevaluesinthetableinrelationtothewatersupplypressureandtemperature,theloadandthetypeofwash.Waterandenergyconsumptionrefer
tothedefaultsettingoftheprogrammes;selectingspecialoptionsormodifyingspinspeedortemperaturewillchangetheconsumptiondata.
Theprogrammedurationmaydifferfromthevaluesindicatedaboveasitdependsontheoperationconditionsapplicableatthattime(seealso
“TroubleshootingGuide”inyourInstructionsforUse).
* Toreducethewatertemperature,somecoldwaterisaddedattheendofthemainwashcycle,beforethepumpdrainsthewaterout.
** ReferenceProgrammesforEnergyLabel.
*** Automaticadaptionofprogrammedurationafterdetectionofwashload.