Master cook SRCG13003 User manual

Brand: Master cook

Model: SRCG13003

Category: Barbecues & grills

Type: User manual

This manual is also suitable for

57cm Kettle Charcoal Grill

Model# SRCG13007

User Manual

1. This grill is for outdoor use only, and shall not be used in a building, garage, or any other enclosed area.

2. This NOT for commercial use.

3. Do not use grill for indoor cooking or heating. Toxic carbon monoxide fumes can accumulate and cause asphyxiation.

4. Do not use lighter fluid, paraffin, or alcohol for lighting.

5. Do not use in an explosive atmosphere. Keep grill area clear and free from combustible materials, lighter fluid and

other flammable vapors and liquids.

6. Do not store or use lighter fluid or other flammable liquids or vapors within 25 feet (7.62 m) of this appliance.

7. Instant light charcoal can burn at very high temperatures during initial startup. Make sure lid is open until charcoal

turns to hot coals.

8. Keep all combustible items and surfaces at least 21 inches (53 cm) away from the grill at all times.

DO NOT use this grill or any gas product under any overhead or near any unprotected combustible constructions.

9. Do not alter grill in any manner.

10. Do not use the grill unless it is completely assembled and all parts are securely fastened and tightened.

11. This grill should be thoroughly cleaned and inspected on a regular basis.

12. Do not use this appliance without reading “Operating Instructions” in this manual.

13. Do not touch metal parts of grill until it has completely cooled (about 45 min after use) to avoid burns, unless you are wearing

protective gear (pot holders, gloves, grill mittens, etc.).

14. Never touch grates (charcoal or cooking), ashes, or coals to see if they are hot.

15. Do not use on wooden decks, wooden furniture, or other combustible surfaces.

16. Do not use in or on boats or recreational vehicles.

17. Position grill so wind can not carry ashes to combustible surfaces.

18. Do not use in high winds.

19. Never lean over the grill when lighting.

20. Do not leave a lit grill unattended , especially keep children and pets away from grill at all times.

21. Do not attempt to move grill when in use. Allow the grill to cool before moving or storing.

22. Always open grill lid carefully and slowly as heat and steam trapped within grill can severely burn you.

23. Always place your grill on a hard, non-combustible level surface. An asphalt or blacktop surface may not be acceptable for

this purpose.

24. Do not remove the ashes until they are completely and fully extinguished.

25. Live hot briquettes and coals can create a fire hazard.

26. Always empty the ash catcher and grill after each use. Do not remove the ashes until they are completely and fully extinguished.

27. Do not place fuel (charcoal briquets, wood or lump charcoal) directly into bottom of grill. Place fuel only on the charcoal pan/grid.

28. Check to make sure the air vents are free of debris and ash before and while you are using the grill.

29. Make sure ash catcher is securely and completely in place before using the grill.

30. Always wear protective gloves when adding fuel to retain desired heat level.

31. Keep all electrical cords away from a hot grill.

32. Always use a meat thermometer to ensure food is cooked to a safe temperature.

33. The handle is used for pushing and pulling the cooking grid only, and should always be detached from the cooking grid when

fire is on.

34.The hot cooking grid can only be operated by handle provided.

35. Do not touch the hot cooking grid by hand.

36.The handle should always be kept away from the cooking grid when the grill is burning.

37. Attention! This grill will become very hot. Do not move it during operation.

38. Caution! Do not use lighter fluid or comparable fluids for lighting or re-lighting!

39. Property damage, serious injury, or death may occur if the above is not followed exactly.

WARNING FOR YOUR SAFETY

BURNING CHARCOAL RELEASES CARBON

MONOXIDE WHICH HAS NO ODOR AND

CAN CAUSE SERIOUS INJURY OR DEATH.

NEVER BURN CHARCOAL INSIDE HOMES,

VEHICLES OR TENTS.

CARBON MONOXIDE HAZARD

PLEASE CAREFULLY READ ALL SAFETY,

ASSEMBLY AND USAGE PROCEDURES

CONTAINED IN THIS OWNER’S MANUAL

BEFORE USING YOUR BARBECUE GRILL.

FAILURE TO FOLLOW SAFETY

GUIDELINES CAN RESULT IN SERIOUS

PERSONAL INJURY AND/OR PROPERTY

DAMAGE.

W A R N I N G W A R N I N G

Exploded View

1. Thermometer

2. Lid

3. Lid handle

4. Cooking grid

5. Charcoal grid

6. Bowl handle

7. Leg support bracket

8. Leg cup

9. Front leg

10. Storage shelf

11. Lid hinge(pre-installed on lid)

12. Warming rack

13. Bowl hinge(pre-installed on bowl)

14. Bowl air vent

1 pc

4 pcs

2 pcs

1 pc

1pc

15. Ash cup support ring

16. Ash cup

17. Wheel Leg

18. Wheel

19. Fire bowl

20. Air vent handle

21. Thermometer back plate

22. Ash cup handle

23. Wheel cap

24. Grill cover

25. Lid air vent

26. Left side table assembly

27. Right side table assembly

28. Hooks

1 pc

2 pcs

1 pc

1pc

2 pcs

1 pc

1pc

Parts No.

4 pcs

8 pcs

4 pcs

1 pc

16 pcs

Description Qty

Parts No.

8 pcs

5 pcs

2 pcs

1 pc

6 pcs

4 pcs

Description Qty

M6X12 Bolt

M8 Locking nut

M6 Locking nut

M5X12 Bolt

M8 Washer

(pre-installed on

thermometer)

(4pcs preinstalled

on legs)

M6 Large washer

M6 Fibre washer

M6 Small washer

M6 Connecting rod

ATTENTION:

CHECK ALL PARTS BEFOREASSEMBLY PRIOR TO INSTALL THE ABOVE PARTS BEFORE START THE FOLLOWING

ASSEMBLY SETPS

M6 Wing nut

M6X15 Bolt

M6X20 Bolt

M6X30 Bolts

(pre-installed

on legs)

M5 Wing nut

8 pcs

3 pcs

1 pc

M6 nut

M5 Nut

Φ10 Bolt

(pre-installed

on thermometer)

M8 Wing nut

Hardwares List

Tools Required

Phillips Head Screwdriver

(Not included)

Adjustable Wrench

(Not included)

Assembly Instructions

Step 1

a. Install the (3) lid handle to the (2) lid with

2pcs (P) M6 wing nuts and 2pcs (E) M6

large washers.

b. First unscrew the 1pc (M) M8 wing nut and

1pc(D) M8 washer, which have been pre-installed

on the (1) thermometer.Install the (1) thermometer

and (21) thermometer back plate to the (2) lid with

1pc (D) M8 washer and 1pc (M) M8 wing

nut.

c. Attach the (25) lid air vent to the (2) lid with

1 pc (C) M5 x 12 bolt,1 pc (Q) M5 wing nut

and 1 pc (G) M6 small washer.

Finished illustration

Hardware Used

M6 Wing nut

M6 Large washer

2pcs

M6 Small washer

1pc

M8 Washer

1pc

M8 wing nut

1pc

M5 Wing nut

1pc

M5x12 Bolt

1pc

a. Install the (6) bowl handle to the (19) fire

bowl with 2pcs (P) M6 wing nuts and 2pcs

(E) M6 large washers.

b. Install the (15) ash cup supporting ring to

the (19) fire bowl bottom with 3pcs (C)

M5X12 Bolts and 3pcs (K) M5 nuts.

Assembly Instructions

Step 2

Finished illustration

M6 Wing nut

M6 Large washer

Hardware Used

2pcs

M5X12 Bolt

3pcs

M5 Nut

b. Fix the (14) bowl air vent to the (19) fire

bowl bottom by inserting the (20) air vent

handle through the hole of (15) ash cup

support ring, the two holes of (14) bowl

air vent supports and the center hole of

(N)Φ10 bolt bottom as illustration shown,

then insert the (L) pin to the hole of the (20)

air vent handle.

Step 3

a. Put 1pc (N)Φ10 bolt through the center holes

of the (19) fire bowl bottom and (14) bowl air

vent.

Assembly Instructions

Bowl air vent

support

Finished illustration

Φ10 Bolt

Hardware Used

1pc

Finished illustration

Assembly Instructions

Step 5

Lock the 3pcs posts on the (16) ash cup into

the (15) ash cup support ring.

Step 4

Install the (22) ash cup handle to the (16)

ash cup with 2pcs (P) M6 wing nuts and

4pcs (G) M6 small washers.

M6 Wing nut

M6 small washer

Hardware Used

2pcs

4pcs

Finished illustration

post

Step 6

Install 4pcs (7) leg support brackets to the

(19) fire bowl bottom with 8pcs (B) M6X12

bolts and 8pcs (F) M6 fibre washers and

8pcs (J) M6 nuts.

M6 Nut

M6 Fibre washer

Hardware Used

8pcs

M6X12 Bolt

8pcs

c. Insert two ends of (10) storage shelf without

threads into the holes of the 2pcs (9) front legs.

a. Attach the 4pcs (8) leg cups to the 4pcs legs

Assembly Instructions

Step 7

b. First unscrew the 4pcs(A) M6X30 bolts and

4pcs (E) M6 large washers, which have been

pre-installed on the (9 &17)four legs.

Connect the four legs (9&17) to the (19) fire

bowl by inserting the four legs top ends

to the 4pcs (7) leg support brackets with

4pcs (A) M6X30 bolts and 4pcs (E) M6 large

washers . Make sure the 4pcs (A) M6x30

bolts are not fully tightened.

Note: Make sure the two (17) wheel legs are

at the same side of (13) bowl hinge. See

finished illustration.

M6X30 Bolts

M6 large washer

4pcs

Hardware Used

Finished illustration

Install the lid assembly to the fire bowl

assembly by connecting the (11) lid hinge

and (13) bowl hinge with 1pc (O) M6

Connecting rod and 1pc (I) M6 locking nut.

Assembly Instructions

Step 8

Hardware Used

M6 Connecting rod

1pc

M6 Locking nut

Finished illustration

1pc

d. Insert two ends with thread of the (10)

storage shelf into the holes of the 2pcs

(17) wheel legs and 2pcs (18) wheels,

and tighten with 2pcs (H) M8 locking nuts.

Then attach the 2pcs (23) wheel caps

onto the 2pcs (18) wheels.Then tighten

the 4pcs(A) M6x30 bolts in step 7b.

M8 Locking nut

Hardware Used

2pcs

Assembly Instructions

Step 9

a. Install the (26) left side table assembly to the (19)

fire bowl with 2pcs (S) M6x15 bolts, 2pcs (R)

M6 x20 bolts and 4pcs ( E) M6 large washers.

Finished illustration

M6 Large washer

M6X15 Bolt

M6X20 Bolt

4pcs

2pcs

b. Install the (27) right side table assembly to the

(19) fire bowl with 2pcs (S) M6x15 bolts, 2pcs (R)

M6 x20 bolts and 4pcs ( E) M6 large washers.

NOTE: MAXIMUM WEIGHT ON SIDE

TABLE: 4.5 KGS/9.9 LBS

Hardware Used

M6 Large washer

M6X15 Bolt

M6X20 Bolt

4pcs

2pcs

Hardware Used

Finished illustration

a. Place the (5) charcoal grid , (4) cooking grid

into (19) fire bowl in order as shown, then fix

the (12) warming rack to the (2) lid and (19)

fire bowl.

Assembly Instructions

Step 10

b. Hang the (28) hooks onto the (19) fire bowl.

Assembly Instructions

Step 11

b. To raise side table, flip up and push down slightly to position, proceed as shown.

Table Operation

a. To lower side table, lift the side table up slightly, and flip down as shown.

Easy access grate for

refilling charcoal

cooking grid

WARNING

For Your Safety

1. The handle is used for pushing and pulling the cooking grid only, and should always be detached from

the cooking grid when fire is on.

2. The hot cooking grid can only be operated by handle provided.

3. Do not touch the hot cooking grid by hand.

4. The handle should always be kept away from the cooking grid when the grill is burning.

This appliance is designed for use only with quality charcoal briquette, lump charcoal and cooking wood.

Attention! This will become very hot. Do not move it during operation. Do not use indoors!

Caution! Do not use , lighter fluid or comparable fluids for lighting or re-lighting!

Warning! Keep children and pets away.

Lighting

1. Open lid and vents.

2. Make sure ash cup is empty.

3. Remove cooking grid.

4. Arrange and light fuel per instructions on fuel package.

Direct Cooking

1. While wearing protective gloves, carefully spread coals evenly across grid with a long handle tool.

2. Carefully replace cooking grid.

3. Place food on cooking grid.

4. Cook with lid open or closed.

Indirect Cooking – Ideal for Roasts

1. While wearing protective gloves, carefully spread coals into a donut shape with a long handle tool.

2. Place a metal tray in center of donut to catch drippings

3. Carefully replace cooking grid.

4. Place food on cooking grid directly over the metal pan.

5. Cook with lid closed.

Tips for Better Cookouts and Longer Product Life

1. Store fuel in a waterproof container away from sources of ignition.

2. Use a charcoal chimney for fast and easy startups.

3. Spray or coat cooking su

rfaces with vegetable oil before cooking to avoid sticking.

4. Place vegetables or delicate foods into aluminum foil pouches.

5. Use a quality grill brush after each event to keep cooking surfaces clean and rust free.

6. Remove all ash and dispose of properly after each use.

7. Once grill is cool, cover with a quality grillcover that is properly sized to your unit.

Cleaning and Care

Caution:

1. All cleaning and maintenance should be done when grill is cool.

2. DO NOT clean any grill part in a self-cleaning oven. The extreme heat will damage the finish.

3. Abrasive cleaners will damage this product.

4. Never use oven cleaner to clean any part of grill.

Cleaning Surfaces

1. Wipe surfaces clean with mild dishwashing detergent or baking soda.

2. For stubborn surfaces use a citrus based degreaser and a nylon scrubbing brush.

3. Rinse clean with water.

Operating lnstructions

Indirect cooking

Charcoal Rails

Direct cooking

3 - 4cm of coals

Master cook SRCG13003 User manual

Brand: Master cook

Model: SRCG13003

Category: Barbecues & grills

Type: User manual

This manual is also suitable for

Download PDF

report

Master cook SRCG13003 User manual

This manual is also suitable for

Master cook SRCG13003 User manual

Other documents