Edsal HDL301260 Assembly Manual

Brand: Edsal

Model: HDL301260

Type: Assembly Manual

Safety Instructions

These units should be placed on a level surface. Failure to do so can result in poor product performance or create a

possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not

included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY

PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the

heavier loads on the bottom. Use care when working with metal parts.

Light Duty

Steel Shelving

MODEL NUMBER

HDL301260

HDL301260 4 Shelf

60”h x 12”d x 30”w

Description

A - Shelf

B - Post

C - Brace

D - Gussets

E - Hardware

F - Ft. Protector

Qty.

Part Number

HHSH3314

HHPT3102

HHBR2001

HHGU0501

NB58

FP100

Part Size

30” x 12”

31”

20 7/32”

5”

N/A

General Instructions

Assembly is done with the nuts and bolts fitting into the holes of the post and shelf. A regular blade screw driver, 3/8”

socket wrench, or a 3/8” nut driver will be the tools necessary to complete the assembly. During shipping and handling,

some of the parts may bend. Use care when forming them back to the original shape by hand. To assure squareness

of the unit, do not fully tighten the nuts and bolts until final assembly is complete.

Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel

free to contact our Muscle Rack manufacturing facility at, (773) 475-3000 and request customer service.

We can also be reached on the internet at the following email address : [email protected].

To obtain replacement parts, please provide the following information :

- Model # - Part # & Description - Location Purchased - Date Purchased

Consumer Products Division

Edsal Manufacturing Company

4400 South Packers Avenue

Chicago, IL 60609 www.edsal.com

Light Duty Steel Shelving

F - Foot Protector

E - 10-24x1/2”

D - Gusset

B - Post

C - Brace

A - Shelf

Assemble four (4) post sets by using 2 sections of the

split post (see figure A). Overlap the post so that one

hole from the bottom post and one hole from the top

post are aligned. Use two (2) nuts and bolts to fasten

the post together (see figure B). Tighten appropriately.

Assembly Instructions for HDL301260

Bolt the top and bottom shelf to the post assemblies. Make cer-

tain the back of the shelves which have the center hole, are

facing down (see figure C). Align the bottom shelf with the third

hole of the post, insert nuts and bolts and FINGER TIGHTEN

ONLY. Align the top shelf with the first hole of the post insert

the nuts and bolts and FINGER TIGHTEN ONLY (see Figure D).

Install the last two (2) shelves and FINGER TIGHTEN ONLY.

Take four (4) braces for the back and bolt one end of

each brace to the center hole of the 3rd shelf, FINGER

TIGHTEN ONLY. Bolt the opposite end of each braces

to the sides of the posts, FINGER TIGHTEN ONLY

(see figure E). Install the side braces one (1) on each

side of the unit between the 2nd and the third shelves,

FINGER TIGHTEN ONLY (see figure F).

Place the unit on a level surface so that the unit is square.

Hold the unit securely and tighten all nuts and bolts appro-

priately. After all nuts and bolts are secure, install the four

(4) gussets to the four corners of the front of the unit (see

figure G). Tighten nuts and bolts appropriately. Finally

install the four (4) plastic floor guards to the bottom of the

post to help prevent scratching of the floor (see figure H).

Step

Figure A

Figure B

Bolt here

Overlap post by one hole

Front of shelf

Back of shelf

Figure C

Figure D

Center hole

facing down

Center hole

Figure E

Figure F

Bolt to

center

hole

Figure G

Gussets

Figure H

Edsal HDL301260 Assembly Manual

Edsal HDL301260 Assembly Manual

Edsal HDL301260 Assembly Manual

Related papers

Other documents