Homelite ut40530 Owner's manual

Brand: Homelite

Model: ut40530

Type: Owner's manual

To register your Homelite product,

please visit:

http://register.homelite.com/

Pour enregistrer votre produit de

Homelite, s’il vous plaît la visite :

http://register.homelite.com/

Para registrar su producto de

Homelite, por favor visita:

http://register.homelite.com/

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

3 in. WATER PUMP

POMPE À EAU DE 76,2 mm (3 po)

BOMBA DE AGUA DE 76,2 mm (3 pulg.)

UT40530

NOTICE AVIS AVISO

Do not use E15 or E85 fuel in this

product. It is a violation of federal

law and will damage the unit and void

your warranty. Only use unleaded gasoline containing up

to 10% ethanol.

Ne pas utiliser d’essence E15 ou E85 dans ce produit. Une

telle utilisation représente une violation de la loi fédérale

et endommagera l’appareil et annulera la garantie. Utiliser

seulement de l’essence sans plomb ne contenant pas plus

de 10 % d’éthanol.

No utilice combustibles E15 o E85 con este producto. Esto

constituye una violación a la ley federal, dañará la unidad

y anulará la garantía. Use únicamente gasolina sin plomo

con un contenido de hasta 10 % de etanol.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Ce pompe à eau a été conçu et fabriqué conformément aux

strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenu, il vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT :

Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre

le manuel d’utilisation avant d’utiliser ce produit.

Merci de votre achat.

Su lavadora de presión ha sido diseñada y fabricada

de conformidad con las estrictas normas para brindar

fiabilidad, facilidad de uso y seguridad para el operador. Con el

debido cuidado, le brindará muchos años de sólido y eficiente

funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones, el

usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

Your water pump has been engineered and manufactured to our high standard for dependability, ease of operation, and

operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

See this fold-out section for all of the

figures referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner

toutes les figures mentionnées dans le manuel

d’utilisation.

Consulte esta sección desplegable para ver

todas las figuras a las que se hace referencia en

el manual del operador.

Fig. 1

Fig. 4Fig. 2

Fig. 3

A - Throttle lever (levier d’accélérateur, palanca

del acelerador)

B - Choke lever (levier de volet de départ, palanca

del anegador)

C - Fuel lever (levier de carburant, palanca de

combustible)

D - Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

E - Fuel cap (bouchon de carburant, tapa del

combustible)

A - Discharge hose (tuyau d’évacuation,

manguera de descarga)

B - Pump outlet (sortie de la pompe, salida de la

bomba)

F - Priming port cap (bouchon du port

d’amorçage, tapa del puerto de cebado)

G - Pump outlet (sortie de la pompe, salida de la

bomba)

H - Oil cap/dipstick (bouchon/jauge d’huile, tapa

del aceite con varilla de nivel)

I - Fuel tank (réservoir de carburant, tanque de

combustible)

J - Air filter (filtre à air, filtro de aire)

K - Muffler (silencieux, silenciador)

L - Pump inlet (entrée de la pompe, entrada de la

bomba)

M- Engine switch (commutateur de moteur,

interruptor del motor)

N - Hose clamps (colliers de la tuyau, abrazaderas

de manguera)

O - Strainer (crépine, tamiz)

P - Spark plug wrench (clé à bougie, llave para

bujía)

A - Pump inlet (entrée de la pompe, entrada de la

bomba)

B - Suction hose (tuyau d’aspiration, manguera

de aspiración)

A - Suction hose (tuyau d’aspiration, manguera

de aspiración)

B - Strainer (crépine, tamiz)

iii

Fig. 5 Fig. 8

Fig. 9

Fig. 6

Fig. 7

A - Water (eau, agua)

B - Pump chamber (chambre de la pompe,

cámara de la bomba)

C - Priming port cap (bouchon du port

d’amorçage, tapa del puerto de cebado)

A - Suction hose (tuyau d’aspiration, manguera

de aspiración)

B - Discharge hose (tuyau d’évacuation,

manguera de descarga)

C - Strainer (crépine, tamiz)

A - Starter grip and rope (poignée du lanceur et

corde, mango del arrancador y cuerda)

B - OFF (marche, apagado)

C - ON (arrêt, encendido)

D - Engine switch (commutateur de moteur,

interruptor del motor)

A - Throttle lever (levier d’accélérateur, palanca

del acelerador)

B - High speed (vitesse rapide, velocidad alta)

C - Low speed (basse vitesse, velocidad baja)

D - Choke lever (levier de volet de départ, palanca

del anegador)

E - Start (démarrage, arranque)

F - Run (marche, marcha)

G - Fuel valve (robinet de carburant, válvula de

combustible)

H - Closed (fermeture, cerrar)

I - Open (ouvrir, abra)

Fig. 10

A - Oil cap/dipstick (bouchon/jauge d’huile, tapa

del aceite con varilla de nivel)

B - Oil fill hole (orifice de remplissage d’huile,

agujero de llenado de aceite)

C - Funnel (entonnoir, embudo)

Fig. 11

Fig. 12

A - 0.028 in. - 0.03 in. (0.7- 0.8 mm) [0,7 mm

à 0,8 mm (0,028 po à 0,030 po); 0,7 mm a

0,8 mm (0,028 pulg. a 0,030 pulg.)]

A - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

B - Latch (loquet, pestillo)

C - Air filter (filtre à air, filtro de aire)

D - Notch (encoche, muesca)

OFF

A - Fuel cap (bouchon de carburant, tapa del

combustible)

B - Funnel (entonnoir, embudo)

Fig. 13 Fig. 15

Fig. 14

Fig. 16

A - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

B - Container (conteneur, recipiente)

A - Carburetor drain screw (vis de vidange

du carburateur, tornillo de drenaje del

carburador)

B - Fuel sediment cup (cuvette de sédimentation

du carburant, vaso de sedimentación de

combustible)

A - Wire brush (brosse métallique, cepillo de

alambre)

B - Spark arrestor (pare-étincelles, parachispas)

C - Screw (vis, tornillo)

A - Water drain cap (bouchon de purge, tapa del

drenaje de agua)

Page / Página 2

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 Important Safety Instructions ........................................................................................................................................3-4

Instructions importantes concernant la sécurité / Instrucciones importantes de seguridad

 Specific Safety Rules .....................................................................................................................................................4-5

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ......................................................................................................................................................................... 6-7

Symboles / Símbolos

Safety Labels .................................................................................................................................................................7-8

Sûreté étiquète / Etiquetas de seguridad

 Features ............................................................................................................................................................................9

Caractéristiques / Características

 Assembly ...................................................................................................................................................................10-11

Assemblage / Armado

 Operation ................................................................................................................................................................... 11-13

Utilisation / Funcionamiento

 Maintenance ..............................................................................................................................................................14-17

Entretien / Mantenimiento

 Accessories .................................................................................................................................................................... 18

Accessoires / Accesorios

 Troubleshooting .............................................................................................................................................................. 18

Dépannage / Solución de problemas

 Warranty ....................................................................................................................................................................19-20

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Páge arrière / Pág. posterior

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

DANGER:

Carbon Monoxide. Using a water pump indoors CAN

KILL YOU IN MINUTES.

Water pump exhaust contains high levels of carbon

monoxide (CO), a poisonous gas you cannot see or

smell. If you can smell the water pump exhaust, you are

breathing CO. But even if you cannot smell the exhaust,

you could be breathing CO.

Never use a water pump inside homes, garages,

crawl-spaces, or other partly enclosed areas. Deadly

levels of carbon monoxide can build up in these areas.

Using a fan or opening windows and doors does NOT

supply enough fresh air.

ONLY use a water pump outdoors and at least 20 feet

away from open windows, doors, and vents with the

engine exhaust directed away. These openings can

pull in water pump exhaust.

Even when you use a water pump correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home. If you start to

feel sick, dizzy, or weak after the water pump has been

running, move to fresh air RIGHT AWAY. See a doctor.

You could have carbon monoxide poisoning.

WARNING:

Read and understand all instructions. Failure to follow all

instructions listed below could result in electric shock, fire

and/or carbon monoxide poisoning which can cause death

or serious personal injury.

READ ALL INSTRUCTIONS

 Know your water pump. Read the operator’s manual

carefully. Learn the machine’s applications and limitations

as well as the specific potential hazards related to this

water pump.

Keep guards in place and in working order. Never

operate the water pump with any guard, hose, or cover

removed. Make sure all guards are operating properly

and hoses are securely attached before each use.

 Remove adjusting keys and wrenches. Form habit of

checking to see that keys and adjusting wrenches are

removed from water pump before starting the engine.

 To reduce the risk of injury, keep children and

bystanders away. All bystanders should wear safety

glasses and be kept at least 20 feet away.

Keep the area of operation clear of all persons,

particularly small children, and pets.

Do not start or operate the engine in a confined

space, building, near open windows, or in other

unventilated space where dangerous carbon monoxide

fumes can collect. Carbon monoxide, a colorless,

odorless, and extremely dangerous gas, can cause

unconsciousness or death.

 Use the right equipment. Don’t force water pump or

hoses to do a job it was not designed for. Don’t use it for

a purpose not intended.

 Dress properly. Wear long pants and long sleeves. Do not

wear loose clothing, gloves, scarfs, neckties, or jewelry.

They can get caught and draw you into moving parts.

Rubber gloves and nonskid footwear are recommended

when working outdoors. Also wear protective hair

covering to contain long hair above shoulder level.

Do not operate the equipment while barefoot or when

wearing sandals or similar lightweight footwear. Wear

protective footwear that will protect your feet and improve

your footing on slippery surfaces.

Exercise caution to avoid slipping or falling.

 Always wear eye protection with side shields marked

to comply with ANSI Z87.1 along with hearing

protection. Following this rule will reduce the risk of

serious personal injury.

 Don’t overreach or stand on unstable support. Keep

proper footing and balance at all times.

 Use only recommended accessories. The use of

improper accessories may cause risk of injury.

 Follow the maintenance instructions specified in this

manual.

 Check damaged parts. Before further use of the

tool, a

guard or other part that is damaged should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged must

be properly repaired or replaced by a qualified service

center to avoid risk of personal injury.

 Never leave water pump running unattended. Turn

power off. Don’t leave water pump until engine comes

to a complete stop.

Keep the engine and muffler free of grass, leaves, or

grease to reduce the chance of a fire hazard.

 Keep the muffler’s exhaust pipe free of foreign

objects.

Follow manufacturer’s recommendations for

safeloading, unloading, transport, and storage of

machine.

Page 4 — English

SPECIFIC SAFETY RULES

DANGER:

Risk of fire and serious burns: Never remove fuel cap

when unit is running. Shut off engine and allow the unit

to cool at least five minutes. Remove cap slowly.

 Use caution when positioning the water pump for

use. Warm air from the engine could cause discolored

spots on grass, fences, decks, etc.

 Never direct a water stream toward people or pets,

or any electrical device.

Never pick up or carry a machine while the engine is

running.

 Never start the machine if ice has formed in any part

of the equipment.

 Always operate the machine on a flat, stable surface

with a slope of no more than 4˚.

Never attempt to make any adjustments while the

engine (motor) is running (except where specifically

recommended by the manufacturer).

 Protective covers must always cover rotating parts

when the engine is running.

Keep cooling air intake (starter grip and rope area)

and muffler side of the engine at least 3 feet away from

buildings, obstructions, and other combustible objects.

Keep the engine away from flammables and other

hazardous materials.

Keep away from hot parts. The muffler and other engine

parts become very hot even after the engine has been

shut off; use caution.

Do not touch the spark plug and ignition cable when

starting and operating the engine.

 Check fuel hoses and joints for looseness and fuel

leakage before each use.

 Check bolts and nuts for looseness before each use.

A loose bolt or nut may cause serious engine problems.

Always refuel outdoors. Never refuel indoors or in a

poorly ventilated area.

Never store the machine with fuel in the fuel tank

inside a building where ignition sources are present,

such as hot water and space heaters, clothes dryers, and

the like.

If the fuel tank has to be drained, do this outdoors

into a container approved for gasoline and away from all

ignition sources.

To reduce the risk of fire and burn injury, handle fuel

with care. It is highly flammable.

Do not smoke while handling fuel.

Add fuel before starting the engine. Never remove the

cap of the fuel tank or add fuel while the engine is running

or when the engine is hot.

Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

Replace all fuel tank and container caps securely.

IMPORTANT SAFETY INSTRUCTIONS

 Be thoroughly familiar with controls. Know how to stop

the product.

 Keep the water pump’s surface dry, clean, and free

from oil and grease. Always use a clean cloth when

cleaning. Never use brake fluids, gasoline, petroleum-

based products, or any solvents to clean water pump.

 Stay alert and exercise control. Watch what you are

doing and use common sense. Do not rush.

Do not operate the water pump when you are tired, ill,

upset, or while under the influence of drugs, alcohol,

or any medication.

Check the work area before each use. Remove all

objects such as rocks, broken glass, nails, wire, or string

which can be thrown or become entangled in the machine.

Do not use water pump if switch does not turn it off.

Have switches replaced by a qualified service center.

Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent accidental starting.

 Avoid dangerous environment. Don’t smoke or use

near open flames, sparks, or expose to rain. Keep work

area well lit.

 Never use in an explosive atmosphere. Normal

sparking of the motor could ignite fumes.

Do not operate around dry brush, twigs, cloth rags, or

other flammable materials.

 Do not overtilt the unit. Doing so could result in fuel

leakage.

 Do not allow children or untrained individuals to

use this unit.

Page 5 — English

SPECIFIC SAFETY RULES

Wipe spilled fuel from the unit. Move 30 feet away from

refueling site before starting engine.

Ensure all hoses are properly connected before using

the product. Never operate the water pump without all

hoses connected.

Never place hands or any other body part inside pump;

contact with moving parts can cause serious personal

injury.

If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.

Never attempt to burn off spilled fuel under any

circumstances.

Before storing, allow the water pump to cool for 30

minutes and drain fuel from the unit.

Store fuel in a cool, well-ventilated area, safely away

from spark and/or flame-producing equipment.

Store fuel in containers specifically designed for this

purpose.

Empty fuel tank and restrain the unit from moving

before transporting in a vehicle.

When servicing use only recommended or equivalent

parts. Use of any other parts may create a hazard or

cause product damage.

Make sure minimum clearance of 3 feet is maintained

from combustible materials.

Keep hands and body out of the path of the pump’s

discharge.

Secure the pump to reduce the risk of injury or

property damage due to unexpected tool movement.

If any tipping or walking is noticed, stop operation

and anchor the pump to prevent movement.

Secure the outlet hose. An unsecured hose may whip or

“kick back” during operation and cause serious personal

injury.

 Do not use this product to pump gasoline, oils,

petroleum products, acids, alkalines, solvents,

flammable material, bleaches, or industrial grade

solutions. These products can cause physical

injuries to the operator and irreversible damage to the

machine. This water pump is only intended to pump

clean water.

 Risk for consumption. This product should never

be used to supply or drain water intended for human

consumption.

 Do not run the pump without a water source present

as this may damage the pump and decrease the

pump life.

 Prime the pump by pouring water into the priming

port prior to starting the engine. Never start the

engine without priming the pump first.

 Do not interfere with the intake or discharge

function of the pump.

 Do not operate the pump unless a filtered suction

hose is attached and connected to a water source.

 Make sure you do not exceed the unit’s suction

limit.

 Avoid running the pump at low or high speeds for

extended periods of time as this may damage the

pump.

Save these instructions. Refer to them frequently and

use them to instruct other users. If you loan someone this

tool, loan them these instructions also.

Page 6 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye and Hearing Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1 along with hearing protection.

Hot Surface

To reduce the risk of injury or damage, avoid contact with any

hot surface.

Risk of Explosion

Do not pump flammable liquids. Flammable liquids, fuel, and

their vapors are explosive and can cause severe burns or death.

Risk of Fire

Fuel and its vapors are extremely flammable and explosive. Fire

can cause severe burns or death.

Toxic Fumes

Gas products emit carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Page 7 — English

SAFETY LABELS

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Kickback

To reduce the risk of injury from kickback, secure the discharge

hose when the machine is on.

Chemical Burns

To reduce the risk of injury or damage, DO NOT PUMP ACIDS,

ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,

OR INDUSTRIAL GRADE SOLUTIONS with this product.

Lifting Hazard

To reduce the risk of serious injury, avoid attempting to lift the

water pump alone.

Electric Shock

Failure to use in dry conditions and to observe safe practices

can result in electric shock.

The following labels are found on the product. For your safety, please review and understand all of the labels before starting

the product. If any of the labels come off the unit or become hard to read, contact customer service or a qualified service

center for replacement.

Page 8 — English

SAFETY LABELS

940872003-05

NOTICE

DO NOT USE FUEL CONTAINING MORE THAN 10% ETHANOL;

IT IS A VIOLATION OF U.S. FEDERAL LAW,

WILL DAMAGE YOUR PRODUCT, AND VOID THE WARRANTY.

CHECK LUBRICANT

Add lubricant to full mark to start. Engine will not start or will shut off if sensor detects

low lubricant level. • Ajouter de lubrifiant jusqu’au repère de remplissage pour

dèmarrer. Le moteur ne démarre pas ou s’éteint si le capteur détecte le niveau de

lubrifiant faible. • Añada lubricante hasta la marca de ileno para arrancar. El motor no

arranca o se apaga si sensor detecta el nivel de lubricante de baja.

NOTICE AVIS AVISO

940708019-04

L’utilisation de cet équipement peut créer des étincelles susceptibles d’enflammer la végétation sèche. Il peut

être nécessaire d’utiliser un pare-étincelles. L’utilisateur doit communiquer avec le service local d’incendie

pour connaître toutes les lois et tous les règlements portant sur les exigences en matière de prévention des incendies.

El uso de este equipo puede producir chispas propensas a iniciar incendios cerca de vegetación seca. Es posible que

se necesite un parachispas. El operador debe ponerse en contacto con las agencias contra incendios locales para

conocer las leyes y regulaciones relacionadas con los requisitos de prevención de incendios.

WARNING

AVERTISSEMENT

940947009-01

ADVERTENCIA

Operation of this equipment may create sparks that can start fires around dry vegetation. A spark arrestor may be required.

The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.

HOT SURFACE

SURFACES CHAUDE

SUPERFICIES CALIENTE

WARNING

AVERTISSEMENT

ADVERTENCIA

940680055-01

DANGER

L’utilisation d’une pompe à eau à gaz à l’intérieur PEUT VOUS TUER ENQUELQUES MINUTES. Les moteurs produisent

du monoxyde de carbone, un gaz mortel incolore et inodore. Utilisez longueur de tuyau suffisante pour maintenir la

pompe d'au moins 6 mètres (20 pieds) loin de toutes les fenêtres, portes et évents. Dirigez échappement loin de

toutes les fenêtres, portes et évents.

Using a gas water pump indoors CAN KILL YOU IN MINUTES. Engine exhaust contains carbon monoxide. This is a poison

you cannot see or smell. Use sufficient hose length to keep pump at least 20 feet (6 meters) away from all windows,

doors, and vents. Direct engine exhaust away from all windows, doors, and vents.

NEVER use inside

a home, basement,

or garage, EVEN IF

doors and windows

are open.

Only use OUTSIDE

and at least 20 feet

(6 meters) from

windows,

doors, and vents.

DANGER PELIGRO

NE JAMAIS utiliser à l’intérieur d’une maison, sou-sol,

ou d’un garage,MÊME SI les portes et les fenêtres sont

ouvertes. • NUNCA lo use dentro de su hogar, sótano,

o del garaje, INCLUSO con las puertas y las ventanas

abiertas.

Usar un bomba de agua de gas en el interior PUEDE MATARLO EN POCOS MINUTOS. Los gases de escape del

motor contienen monóxido de carbono. Es un veneno que no puede verse ni olerse. Use suficiente longitud de

la manguera de la bomba para mantener al menos 6 metros (20 pies) lejos de todas las ventanas, puertas y

conductos de ventilación. Dirigir agotar lejos de todas las ventanas, puertas y conductos de ventilación.

Utiliser uniquement À L’EXTÉRIEUR et au moin de 6

mètres (20 pieds) des fenêtres, des portes et des

évents. • Sólo utilícelo AL AIRE LIBRE y por lo menos

6 metros (20 pies) de distancia de ventanas, puertas

y respiraderos.

940654251-01

You WILL be KILLED or SERIOUSLY

HURT if you do not follow the

Operator’s Manual instructions.

Ne pas procéder de la manière décrite

dans ce Manuel d’utilisation entraînera

des BLESSURES GRAVES voire la MORT.

SE MATARÁ o LESIONARÁ GRAVEMENTE

si no sigue las instrucciones del Manual del operador.

Risk of fire. Check for any fuel

overflow or leaking. Stop the engine

before refueling. Keep all objects at

least 3 feet (0.91 m) away from this

machine. Heat from Muffler and Exhaust

gases can ignite combustible objects. Do

not add fuel while the product is operating.

Risque d’incendie. Vérifier l'absence de débordement

ou de fuite de carburant. Arrêter le moteur avant de fair le

plein. Éloigner tous les objets au moins de 0,91 m (3 pi) de

cet appareil. La chaleur du pot d’échappement et les gaz

d’échappement peuvent enflammer les objets combustibles. Ne

pas ajouter de carburant pendant l’utilisation de l’appareil.

Riesgo del incendio. Revise si hay algún derrame o fuga de

combustible. Apague el motor antes de poner combustible.

Mantener todos los objetos a una distancia mínima de 0,91 m (3

pies) de esta máquina. El calor de los gases del silenciador y el

escape pueden prender fuego a objetos combustibles.No agregue

combustible cuando el producto esté functionando.

Keep water discharge pointed away from all

electrical devices to reduce the risk of

electrocution or electric shock.

Gardez évacuation de l'eau a l'écart de tous les

appareils électriques afin de réduire le risque

de electrocutuion ou d'électrocution.

Exhaust contains poisonous carbon monoxide gas that can

cause unconsciousness or DEATH. Operate in well ventilated,

outdoor areas at least 20 feet (6 meters) away from all

windows, doors, and vents.

L’échappement contient le gaz monoxyde de carbone

toxique qui peut causer l’inconscience ou la MORT. Fonctionner dans

les secteurs bien ventilés et extérieurs d'au moins 6 mètres (20

pieds) loin de toutes les fenêtres, portes et évents.

El escape contiene gas venenoso de monóxido

de carbono que puede causar pérdida del

conocimiento o MUERTE. Opere en áreas

exteriores bien ventiladas al menos

6 metros (20 pies) lejos de

todas las ventanas,

puertas y conductos

de ventilación.

Eye and Hearing Protection. Always

wear hearing protection and safety

goggles or safety glasses with sideshields,

and as necessary a full faceshield when

operating this product.

Protection oculaire et auditive. Toujours porter

protection auditive et des lunettes de sécurité

munies d’écrans latéraux ou, si nécessaire, un masque facial intégral

lors de l’utilisation de ce produit.

Protección ocular y cabeza. Use siempre para los oidos y gafas de

seguridad con protectores laterales y, de ser necesario, use protección

para toda la cara al utilizar este producto.

Mantenga la descarga de agua

apuntando lejos de todos los

dispositivos eléctricos para

reducir el riesgo de

electrocutuion o una

descarga

eléctrica.

Page 9 — English

FEATURES

KNOW YOUR WATER PUMP

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

AIR FILTER

The air filter helps to limit the amount of dirt and dust drawn

into the unit during operation.

CHOKE LEVER

The choke is used when starting the engine.

ENGINE SWITCH

The engine switch is used either in combination with the

starter grip and rope to start the water pump.

FUEL LEVER

Fuel flow from the fuel tank to the engine is turned on and

off using the fuel lever.

FUEL TANK

This fuel tank has a maximum capacity of 0.95 gal. Use

unleaded automotive gasoline in the engine.

LOW OIL SHUT DOWN PROTECTOR

The low oil sensor causes the engine to stop if the level of

lubricant in the crankcase is insufficient.

OIL CAP/DIPSTICK

Remove the oil fill cap to check and add lubricant to the

water pump when necessary.

OIL DRAIN PLUG

When changing the engine lubricant, unscrew and remove

the oil drain plug to allow old engine lubricant to be drained.

PRIMING PORT

The priming port is used to prime the pump prior to operation.

STARTER GRIP AND ROPE

The starter grip and rope is used (along with the engine

switch) to start the water pump’s engine.

THROTTLE LEVER

The throttle lever is used to control the pump’s speed.

PRODUCT SPECIFICATIONS

ENGINE

Engine Type ...................................................... 212cc OHV

Cooling System .................................................. Forced Air

Starting System .........................................................Recoil

Ignition System ............................................................T.M.I

Spark Plug .......................... Torch/LG F6RTC or equivalent

Engine Lubricant Volume...................Approximately 20 oz.

Fuel Volume ........................................................... 0.95 gal.

PUMP

Port Diameter (Intake/Outlet) ........................................3 in.

Maximum Gallons Per Minute .............................. 264 gpm

Suction Head Lift .........................................................26 ft.

Total Head Lift .............................................................82 ft.

DIMENSIONS

Length .....................................................................19.7 in.

Width .......................................................................16.5 in.

Height ......................................................................18.7 in.

Détecteur de monoxyde

de carbone dans les

pièces habitables

Utiliser seulement À L'EXTÉRIEUR

et TRÈS LOIN de toutes fenêtres,

portes ou bouches d’aération.

INSTALLER ET ÉLOIGNER LA POMPE À EAU D’AU MOINS 6,1 M (20 PI)* AFIN DE

RÉDUIRE LE RISQUE D’INFILTRATION DE MONOXYDE DE CARBONE À

L’INTÉRIEUR DE LA MAISON

* Distance minimale recommandée par le Service de santé et les Centres pour le contrôle et la

prévention des maladies américains (www.cdc.gov/co). Le type de maison et les conditions du vent

peuvent exiger une distance plus grande.

Échappement (CO)

Diriger l’échappement LOIN

de toutes fenêtres, portes et

bouches d’aération.

GARDER À UNE DISTANCE

D’AU MOINS 6,1 M (20 PI)

Page 10 — English

ASSEMBLY

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

NOTE: This tool is heavy and requires two people to lift.

To avoid back injury, keep your knees bent and lift with

your legs, not your back, and get help when needed.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have

carefully inspected and satisfactorily operated the tool.

 If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

PACKING LIST

Water Pump

4-Cycle Engine Lubricant (SAE 30 or SAE 10W30)

Hose Clamps

Spark Plug Wrench

Strainer

Operator’s Manual

NOTE: Suction and discharge hoses (not included)

are needed for operating this tool. Look for these

items where you purchased this product or visit

www.homelite.com.

DANGER:

Make sure you use a long enough hose or combinations

of hoses to keep the water pump at least 20 feet away

from homes, buildings, basements, open windows,

doors, and vents with the engine exhaust directed away.

Engine exhaust contains Carbon monoxide, a colorless,

odorless, and extremely dangerous gas, can cause

unconsciousness or death.

WARNING:

If any parts are damaged or missing do not operate

this water pump until the parts are replaced. Use of this

product with damaged or missing parts could result in

serious personal injury.

WARNING:

Do not attempt to modify this water pump or create

accessories not recommended for use with this product.

Any such alteration or modification is misuse and could

result in a hazardous condition leading to possible serious

personal injury.

WARNING:

Never install parts or make adjustments to the water

pump while the engine is running. To prevent accidental

starting that could cause serious personal injury, always

disconnect the engine spark plug wire from the spark

plug when assembling parts.

WARNING:

Do not attempt to operate the water pump until assembly

is complete. Failure to comply could result in possible

serious personal injury.

INSTALLING SUCTION AND DISCHARGE

HOSES (NOT INCLUDED)

See Figures 2 - 5.

NOTICE:

Never use hoses with inner diameters smaller than 3

in. Smaller hoses will not seal properly and will make it

harder to obtain suction.

To attach suction hose to pump:

 Assemble the strainer.

 Attach one end of the suction hose (not included) to the

strainer using a hose clamp.

Page 11 — English

ASSEMBLY

 Screw the other end of the suction hose onto the pump

inlet. Tighten securely.

NOTE: Be careful to avoid cross-threading, which can

cause the hose to leak during use.

 Pull on the hose to be certain it is properly secured.

To attach discharge hose to pump:

 Screw the collar on the discharge hose (not included)

onto the pump outlet. Hand tighten.

NOTE: Be careful to avoid cross-threading, which can

cause the hose to leak during use.

 Pull on the hose to be certain it is properly secured.

To attach suction hose to water source:

 With the water pump turned off, place the filtered end of

the suction hose into the water source.

NOTE: For maximum suction, keep the distance from the

pump and water source as short as possible.

NOTICE:

Always observe all local regulations when discharging

pumped water. Some areas may have restrictions against

discharging pumped water. Check with the appropriate

authorities before using this water pump.

OPERATION

DANGER:

Carbon Monoxide. Using a water pump indoors CAN

KILL YOU IN MINUTES.

Water pump exhaust contains high levels of carbon

monoxide (CO), a poisonous gas you cannot see or

smell. If you can smell the water pump exhaust, you are

breathing CO. But even if you cannot smell the exhaust,

you could be breathing CO.

Never use a water pump inside homes, garages,

crawl-spaces, or other partly enclosed areas. Deadly

levels of carbon monoxide can build up in these areas.

Using a fan or opening windows and doors does NOT

supply enough fresh air.

ONLY use a water pump outdoors and at least 20 feet

away from open windows, doors, and vents with the

engine exhaust directed away. These openings can

pull in water pump exhaust.

Even when you use a water pump correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home. If you start to

feel sick, dizzy, or weak after the water pump has been

running, move to fresh air RIGHT AWAY. See a doctor.

You could have carbon monoxide poisoning.

WARNING:

Do not allow familiarity with tools to make you careless.

Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1 along with hearing protection.

Failure to do so could result in objects being thrown into

your eyes resulting in possible serious injury.

WARNING:

Do not use any attachments or accessories not

recommended by the manufacturer of this tool. The use

of attachments or accessories not recommended can

result in serious personal injury.

WARNING:

Secure the discharge hose during water pump

operation. Never direct a water stream toward people

or pets, or any electrical device. Failure to heed this

warning could result in serious injury. Discharging

water into electrical devices could result in death by

electrocution or electric shock. Directing water towards

people or pets could result in serious personal injury.

WARNING:

Never operate the water pump without both the

suction hose, suction hose strainer, and discharge

hose installed. Never place hands or any other body

part inside the pump; contact with moving parts can

cause serious personal injury.

Page 12 — English

 Replace the oil cap/dipstick and securely tighten.

To check engine lubricant level:

 Place water pump on a flat, level surface. Do not tilt.

 Unscrew the oil cap/dipstick by turning counter-

clockwise.

 Wipe dipstick clean and re-seat in hole; do not rethread.

 Remove dipstick again and check lubricant level. Lubricant

level should fall within the hatched area on the dipstick.

 If level is low, add engine lubricant until the fluid level rises

to the upper portion of the hatched area on the dipstick.

 Replace and secure the oil cap/dipstick.

NOTICE:

Do not overfill. Overfilling the crankcase may cause

excessive smoke and engine damage.

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel in this product. It is a

violation of federal law and will damage the unit

and void your warranty. Only use unleaded gasoline

containing up to 10% ethanol.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates previously stated are not

covered under warranty.

ADDING GASOLINE TO THE FUEL TANK

See Figure 7.

DANGER:

Risk of fire and serious burns: Never remove fuel cap

when unit is running. Shut off engine and allow the unit

to cool at least five minutes. Remove cap slowly.

WARNING:

Gasoline and its vapors are highly flammable and

explosive. To prevent serious personal injury and property

damage, handle gasoline with care. Keep away from

ignition sources, handle outdoors only, do not smoke

while adding fuel, and wipe up spills immediately.

When adding gas to the water pump, make sure the unit is

sitting on a flat, level surface. If the engine is hot, let the water

pump cool for five minutes before adding gas. ALWAYS fill

the fuel tank outdoors with the machine turned off.

NOTE: This is a 4-cycle engine. DO NOT mix fuel and

lubricant together.

NOTICE:

This product is equipped with a spark arrestor that has

been evaluated by the USDA Forest Service; however,

product users must comply with Federal, State, and

local fire prevention regulations. Check with appropriate

authorities. Contact customer service or a qualified

service center to purchase a replacement spark arrestor.

NOTICE:

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts

are replaced. Contact customer service or a qualified

service center for assistance.

APPLICATIONS

This product is designed to remove clean water only.

WARNING:

Never use this water pump to remove water that has

been contaminated or that may contain gasoline, oil,

acids, or other flammable or toxic substances. Never

use to remove hot water. Improper use of the water

pump may result in serious personal injury.

ADDING/CHECKING ENGINE LUBRICANT

See Figure 6.

NOTE: This machine has been shipped with approximately

2 oz. of lubricant in the engine from testing. You must add

lubricant to the engine before starting it the first time.

NOTICE:

Any attempt to start the engine without adding lubricant

will result in engine failure.

To add engine lubricant:

 Place water pump on a flat, level surface. Do not tilt.

 Move the fuel lever to the CLOSED position.

 Unscrew the oil cap/dipstick by turning counter-

clockwise.

 Before first use, squeeze the entire contents of the

lubricant container provided into the oil reservoir.

After initial use, add 4-stroke engine lubricant (SAE 30 or

SAE 10W30) until the fluid level rises to the upper portion

of the hatched area on the dipstick. Do not overfill.

OPERATION

Page 13 — English

 Mix fuel stabilizer with gasoline according to fuel stabilizer

manufacturer’s directions.

 Before removing the fuel cap, clean the area around it.

Remove the fuel cap slowly.

 Insert a clean funnel into the fuel tank then slowly pour

gasoline into the tank. Fill tank to approximately 1-1/2 in.

below the top of the tank neck (this allows for fuel

expansion).

 Replace fuel cap and tighten until the cap “clicks”.

 Clean up any spills before starting the engine.

WARNING:

Always shut off engine before fueling. Never remove

fuel cap or add fuel to a machine with a running or hot

engine. Make sure the unit is sitting on a flat, level surface

and only add fuel outdoors. If the engine is hot, let the

unit cool for at least five minutes before adding fuel.

After fueling, immediately replace fuel cap and tighten

securely. Move at least 30 ft. from refueling site before

starting engine. Do not smoke and stay away from open

flames and sparks! Failure to follow these instructions

could result in a fire and cause serious personal injury.

PRIMING THE PUMP

See Figure 8.

NOTICE:

Never start the engine if the pump is dry or if there isn’t

enough water in the unit to prime the pump.

 Place water pump on a flat, level surface.

 Remove the priming port cap by turning counter-

clockwise.

 Add water until pump chamber is full.

 Replace priming port cap and tighten securely.

STARTING AND STOPPING THE WATER

PUMP

See Figures 9 - 10.

NOTICE:

Do not run the water pump without filtered suction hose

(not included) attached and connected to water source,

as this may damage the pump. Make sure the hose is not

being restricted by tires, rocks, or any other objects that

may lessen or prevent water flow to the pump.

Before starting the engine:

Connect all hoses.

Check all fluids (lubricant and gas).

Ensure pump is primed.

OPERATION

To start the engine:

Move the throttle lever all the way to the right (low speed).

Move the choke left to the START position.

Move the fuel lever right to the OPEN position.

Put the engine switch in the ON position.

Grasp the starter grip and rope and pull slowly until

resistance is felt. Give the starter grip and rope a short,

brisk pull to start the engine.

NOTE: Do not allow the starter grip and rope to snap

back after starting; return it gently to its original place.

Let engine run for 15-30 seconds, then move choke

right to the RUN position and adjust the throttle lever for

desired speed. See Adjusting Pump Speed.

To stop the engine:

Move the throttle lever all the way to the right (low speed).

Put the engine switch in the OFF position.

Move the fuel lever left to the CLOSED position.

WARNING:

While operating and storing, keep at least 3 feet of

clearance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time

before storage. Heat created by muffler and exhaust

gases could be hot enough to cause serious burns and/

or ignite combustible objects.

ADJUSTING PUMP SPEED

See Figure 9.

The throttle lever is used to adjust the cycle speed of the

pump. Constantly operating the pump at extreme speeds (high

or low) can cause damage to the tool’s internal components.

 Turn the water pump on.

 Let the engine run for several seconds.

 To increase the speed of the pump, move the throttle

lever to the left.

 To decrease the speed of the pump, move the throttle

lever to the right.

HIGH ALTITUDE OPERATION

Your engine is configured for operation below 3000 feet

altitude at the factory. Your engine must be reconfigured for

operation above 3000 feet altitude. Operating the engine

with the wrong engine configuration at a given altitude may

increase its emissions, decrease fuel efficiency, degrade per-

formance, and cause irreversible damage. Engines configured

for high altitude operation cannot be operated in standard

altitude conditions. A qualified service center should ensure

that your engine is properly configured for your location.

Page 14 — English

Normal maintenance, replacement or repair of emission con-

trol devices and systems may be performed by any qualified

repair establishment or individual with original or equivalent

parts. Warranty and recall repairs must be performed by an

authorized service center; please contact customer service

for assistance.

WARNING:

Before inspecting, cleaning, or servicing the machine,

shut off engine, wait for all moving parts to stop, and

disconnect spark plug wire and move it away from spark

plug. Allow 30 minutes of cool down time before perform-

ing any maintenance. Failure to follow these instructions

can result in serious personal injury or property damage.

WARNING:

When servicing, use only recommended or equivalent

replacement parts. Use of any other parts could create

a hazard or cause product damage.

NOTICE:

Periodically inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts,

caps, etc. Tighten securely all fasteners and caps and

do not operate this product until all missing or damaged

parts are replaced. Please contact customer service or a

qualified service center for assistance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which can result in serious personal injury.

Before running the engine, perform the following pre-

operation steps:

Check that all bolts, nuts, etc., are securely tightened.

Make sure the air filter is clean.

Check the engine lubricant level, priming water level, and

the fuel tank level; refill as needed.

Inspect the work area for hazards.

If there is excessive noise or vibration, stop the unit

immediately.

MAINTENANCE

CLEANING THE AIR FILTER

See Figure 11.

A dirty air filter will cause starting difficulty, loss of

performance, and shorten the life span of the engine. Check

the air filter monthly. For best performance, replace the air

filter at least once a year.

Press in on the latch to open the cover.

Remove the air filter cover.

Lift the edge of the air filter carefully and pull it out.

Wash the air filter with warm, soapy water.

Rinse and squeeze to dry.

Put small amount of engine lubricant (SAE 30) on the filter

sponge. Squeeze out the excess lubricant then reinstall

the air filter.

NOTE: Make sure the filter is seated properly inside the

cover. Installing the filter incorrectly will allow dirt to enter

the engine, causing rapid engine wear.

To reinstall the air filter cover, insert the latch into the

notch. Close the cover and push the latch until it snaps

into place.

CHECKING SPARK PLUG

See Figure 12.

Clean the area around the base of the spark plug before

removing to keep dirt and debris out of the engine.

Remove spark plug using spark plug wrench provided.

Clean off carbon deposits on the spark plug electrode

using a plug cleaner or wire brush. Replace the plug

if worn. For replacement spark plug, see Product

Specifications earlier in this manual or the accompanying

engine manual, if applicable.

Check electrode gap. The gap should be .028 in. to .032 in.

(0.7- 0.8 mm). Adjust the gap, if necessary, by carefully

bending the ground electrode.

Reinstall spark plug. Tighten securely.

Page 15 — English

FUEL CAP, TANK, AND LINES

WARNING:

Check for fuel leaks. A leaking fuel cap, tank, or lines

are a fire hazard and must be replaced immediately. If

you find any leaks, correct the problem before using the

product. Failure to do so could result in a fire that could

cause serious personal injury.

DRAINING FUEL TANK/CARBURETOR

See Figure 15.

To help prevent gum deposits in the fuel system, drain the

fuel from the tank and carburetor before storing.

Turn off the water pump.

Move the fuel lever to the CLOSED position.

Position a container under the fuel sediment cup and

carburetor drain screw to catch fuel.

Remove the carburetor drain screw and fuel sediment cup.

Allow fuel to drain completely into container.

Retighten drain screw and reinstall fuel sediment cup.

NOTE: Consult hazardous waste management guidelines in

your area for the proper way to dispose of used fuel.

DRAINING THE WATER PUMP

See Figure 16.

Turn off the water pump.

Place a container underneath the water drain cap to

collect water.

Loosen the water drain cap and drain the water.

NOTICE:

Do not store the water pump with water in the priming

tank.

Replace the water drain cap. Tighten securely.

STORING OF THE WATER PUMP

NOTE: Regular use of fuel stabilizer will give you better

performance of the unit. See the Replacement Parts List

for available sizes and part numbers of these items and

call customer service to order.

WARNING:

While storing keep at least 3 feet of clearance on all sides

of this product, including overhead. Allow a minimum

of 30 minutes of “cool down” time before storage. Heat

created by muffler and exhaust gases could be hot

enough to ignite combustible objects.

MAINTENANCE

CHANGING ENGINE LUBRICANT

See Figure 13.

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious

burns.

Remove the oil cap/dipstick.

Place a container underneath the oil drain plug to collect

used lubricant as it drains.

Unscrew the oil drain plug and remove.

Allow lubricant to drain completely.

Reinstall the oil drain plug and tighten securely.

Refill with lubricant following the instructions in the

Adding/Checking Lubricant section. For amount of

lubricant needed to refill, see Product Specifications

earlier in the manual, if applicable.

Reinstall the oil cap/dipstick.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local lubricant retailer for more

information.

CLEANING THE EXHAUST PORT AND MUFFLER

Depending on the type of fuel used, the type and amount

of lubricant used, and/or your operating conditions, the

exhaust port and muffler may become blocked with carbon

deposits. If you notice a power loss with your gas-powered

products, you may need to remove these deposits to restore

performance. We highly recommend that only qualified service

technicians perform this service.

SPARK ARRESTOR

See Figure 14.

NOTICE:

This product is equipped with a spark arrestor that has

been evaluated by the USDA Forest Service; however,

product users must comply with Federal, State, and

local fire prevention regulations. Check with appropriate

authorities. Contact customer service or a qualified

service center to purchase a replacement spark arrestor.

Inspect the spark arrestor for breaks or holes. Replace if

necessary.

Remove the screws securing the spark arrestor in place.

Then, remove the spark arrestor.

Use a wire brush to remove carbon deposits from the

spark arrestor as needed.

Replace the spark arrestor and reinstall the screws.

Tighten securely.

Page 16 — English

MAINTENANCE

Store in a dry, covered area where the weather can’t damage it.

It is important to store this product in a frost-free area. Always

empty water from all hoses and the pump before storing.

Drain the fuel tank completely as described in DRAINING

FUEL TANK/CARBURETOR earlier in this section.

Stored gas can go stale in 30 days.

NOTE: Make sure the the unit is connected to a water

supply when allowing the water pump engine to run.

Make sure the engine switch is off and fuel lever is in the

CLOSED position.

Remove and store the suction and discharge hoses. Do

not allow the hoses to become kinked.

Empty water from the pump and pull the starter grip and

rope about 6 times. This should remove most of the liquid

from the pump.

Drain the lubricant and replace with fresh, clean lubricant

as described in Adding/Checking Engine Lubricant in

the Operation section of this manual.

Disconnect spark plug wire and remove the spark plug.

Pour about a teaspoon of clean, air-cooled, four-cycle

lubricant through the spark plug hole into the combustion

chamber.

Leaving the spark plug out, pull the starter grip and rope

two or three times to coat the inside of the cylinder wall.

Inspect the spark plug and clean or replace, as necessary.

Reinstall the spark plug, but leave the spark plug wire

disconnected.

Clean the air filter.

Extend the recoil starter rope to check its condition. If the

rope is frayed, have it replaced immediately by a qualified

service center.

Store the unit and accessories in an area that does not

reach freezing temperatures. Do not store near furnace or

other sources of heat that could dry out the pump seals.

PREPARING FOR USE AFTER STORAGE

Pull the starter grip and rope three or four times to clean

lubricant from the combustion chamber.

Remove spark plug from the cylinder. Wipe lubricant from

the spark plug and return it to the cylinder.

Reconnect the spark plug wire.

Refuel the machine as described earlier in the operator’s

manual.

Page is loading ...

Homelite ut40530 Owner's manual

Brand: Homelite

Model: ut40530

Type: Owner's manual

Download PDF

report

in other languages

français: Homelite ut40530 Le manuel du propriétaire
español: Homelite ut40530 El manual del propietario

Homelite ut40530 Owner's manual

Homelite ut40530 Owner's manual

in other languages

Related papers

Other documents