STIEBEL ELTRON BHE Style Operation Instruction

BEDIENUNG UND INSTALLATION

OPERATION AND INSTALLATION

UTILISATION ET INSTALLATION

GEBRUIK EN INSTALLATIE

ЭКСПЛУАТАЦИЯ И МОНТАЖ

Bad-/Handtuch-Heizkörper |Bathroom radiator/towel rail | Chauffe-serviettes | Bad-/

handdoekradiator |

Радиатор для ванной / сушилка для полотенец

» BHE 100 Style

Page is loading ...

12 | BHE Style www.stiebel-eltron.com

CONTENTS | SPECIAL INFORMATION

SPECIAL INFORMATION

OPERATION

1. General information �� 13

1.1 Safety instructions ��13

1.2 Other symbols in this documentation ��13

1.3 Units of measurement ��13

2. Safety �� 13

2.1 Intended use ��13

2.2 General safety instructions �� 13

3. Appliance description �� 14

4. Operation �� 14

4.1 User interface description �� 14

4.2 Operation as an electrical room heater �� 14

4.3 Frost protection ��15

4.4 Operation within a DHW/central heating system ��15

4.5 Shutting down ��15

4.6 Childprooﬁng �� 15

5. Cleaning, care and maintenance �� 16

6. Troubleshooting �� 16

INSTALLATION

7. Safety �� 17

7.1 General safety instructions �� 17

7.2 Instructions, standards and regulations �� 17

8. Appliance description �� 17

8.1 Standard delivery �� 17

9. Installation �� 17

9.1 Installation site �� 17

9.2 Wall mounting �� 17

9.3 Hydraulic connection (when integrating into a DHW/

central heating system) ��18

9.4 Fitting the bathrobe hooks �� 18

9.5 Power supply �� 18

10. Troubleshooting �� 18

11. Appliance handover �� 18

12. Speciﬁcation �� 19

12.1 Dimensions �� 19

12.2 Minimum clearances �� 19

12.3 Data table �� 19

SPECIAL INFORMATION

- Keep children under the age of 3 away from

the appliance if constant supervision cannot be

guaranteed.

- Children from the age of 3 to 7 may switch the

appliance on and off, provided they are super-

vised or have been instructed in the safe oper-

ation of the appliance and understand any risks

that may result there from. This is subject to the

appliance having been installed as described.

Children from the age of 3 to 7 must not plug

the power cable into its socket nor regulate the

appliance.

- The appliance may be used by children aged8

and up and persons with reduced physical, sen-

sory or mental capabilities or a lack of experience

and know-how, provided that they are supervised

or they have been instructed on how to use the

appliance safely and have understood the result-

ing risks.

- Children must never play with the appliance. Chil-

dren must never clean the appliance or perform

user maintenance unless they are supervised.

- Parts of the appliance can get very hot and may

cause burns.

Particular caution is advised when children or

vulnerable persons are present.

- Never install the appliance directly below a wall

socket.

- In the case of a permanent connection, the ap-

pliance must be able to be separated from the

power supply by an isolator that disconnects all

poles with at least 3 mm contact separation.

- In the event of damage to the power cable this

must always be replaced by a qualiﬁed electrician

authorised by the manufacturer, using original

spare parts.

- Secure the appliance as described in chapter “In-

stallation/ Installation”.

OPERATION

General information

ENGLISH

www.stiebel-eltron.com BHE Style | 13

OPERATION

1. General information

The chapters "Special Information" and "Operation" are intended

for the user and for qualiﬁed contractors.

The chapter "Installation" is intended for qualiﬁed contractors.

Note

Read these instructions carefully before using the appli-

ance and retain them for future reference.

Pass on the instructions to a new user if required.

1.1 Safety instructions

1.1.1 Structure of safety instructions

!

KEYWORD Type of risk

Here, possible consequences are listed that may result

from failure to observe the safety instructions.

 Steps to prevent the risk are listed.

1.1.2 Symbols, type of risk

Symbol Type of risk

Injury

Electrocution

Burns

(burns, scalding)

1.1.3 Keywords

KEYWORD Meaning

DANGER Failure to observe this information will result in serious

injury or death.

WARNING Failure to observe this information may result in serious

injury or death.

CAUTION Failure to observe this information may result in non-seri-

ous or minor injury.

1.2 Other symbols in this documentation

Note

General information is identiﬁed by the symbol shown

on the left.

 Read these texts carefully.

Symbol Meaning

Material losses

(appliance damage, consequential losses and environmen-

tal pollution)

Appliance disposal

 This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

1.3 Units of measurement

Note

All measurements are given in mm unless stated oth-

erwise.

2. Safety

2.1 Intended use

The appliance is an electric direct heater for installation on a wall.

This appliance has been designed as a booster heater and for use

during spring and autumn. It is particularly suitable for bathrooms

and for drying bathrobes and towels.

The appliance is intended for domestic use. It can be used safely

by untrained persons. The appliance can also be used in a non-do-

mestic environment, e.g. in a small business, as long as it is used

in the same way.

Any other use beyond that described shall be deemed inappropri-

ate. Observation of these instructions and of instructions for any

accessories used is also part of the correct use of this appliance.

2.2 General safety instructions

!

WARNING Injury

Keep children under the age of 3 away from the appliance

if constant supervision cannot be guaranteed.

Children from the age of 3 to 7 may switch the appliance

on and off, provided they are supervised or have been

instructed in the safe operation of the appliance and un-

derstand any risks that may result there from. This is sub-

ject to the appliance having been installed as described.

Children from the age of 3 to 7 must not plug the power

cable into its socket nor regulate the appliance.

The appliance may be used by children aged8 and up and

persons with reduced physical, sensory or mental capa-

bilities or a lack of experience and know-how, provided

that they are supervised or they have been instructed on

how to use the appliance safely and have understood the

resulting risks.

Children must never play with the appliance. Children

must never clean the appliance or perform user main-

tenance unless they are supervised.

CAUTION Burns

Parts of the appliance can get very hot and may cause

burns. Particular caution is advised when children or

vulnerable persons are present.

Note

Operate the appliance only when fully installed and with

all safety equipment ﬁtted.

!

OPERATION

Appliance description

14 | BHE Style www.stiebel-eltron.com

3. Appliance description

This appliance has been designed as a booster heater and is par-

ticularly suitable for bathrooms, as well as for drying and warm-

ing bathrobes and towels. You can place your towels at various

heights.

The appliance heats the room through natural convection and

radiated warmth. The integral room thermostat keeps the room

at the set temperature. For this, it is important that the appliance's

heating output matches the room's heat demand. This only applies

if no towels or bathrobes are hung on the appliance.

The appliance is ready for operation when it has been ﬁxed to the

wall and plugged into the mains.

You can operate the appliance within a DHW/central heating sys-

tem. When the central heating is off, the appliance is operated via

an integral electric direct heater rod.

4. Operation

4.1 User interface description

1/4h

1/2h 1h

2h

26�07�80�0003

1

5

6

8 4

32

7

1 ON/OFF indicator

2 Boost function indicator

3 Timer for boost function

4 Pushbutton for boost function

5 ON/OFF button for the user interface

6 Heating indicator

7 Frost protection setting range

8 Temperature selector

4.2 Operation as an electrical room heater

4.2.1 Switching the appliance on

 Press the ON/OFF button.

The ON/OFF indicator lights up.

 Set the required room temperature with the temperature se-

lector. You can choose from between 6°C and 30°C.

The heating indicator lights up as soon as the appliance starts to

heat. The heating indicator goes off when the temperature set at

the temperature selector has been reached.

Note

If several appliances have been installed in one room, a

different temperature can be set at each one.

Note

To avoid excessive power consumption when windows

are open, switch the appliance off while airing.

4.2.2 Boost function

When the boost function is enabled, the appliance heats at full

power for a maximum of two hours.

Activating

 Switch the appliance on.

 Press the boost function pushbutton.

The boost function indicator lights up.

 Use the boost function timer to set the required duration.

The appliance enables the boost function for the preselected pe-

riod.

At the end of the preselected period, the appliance returns to

standard operation, controlled by the temperature selector. The

boost function indicator goes off.

Note

If you switch the appliance off while the boost function is

enabled, the preselected boost function period is contin-

ued when the appliance is switched back on.

Deactivating

 Press the boost function pushbutton again.

The boost function indicator goes off. The appliance returns to

standard operation controlled by the temperature selector.

4.2.3 24 h automatic function

When the 24h automatic function is activated, the appliance au-

tomatically heats for 2h every 24hours, at full output.

Activating

 Hold down the boost function button and press the ON/OFF

button twice.

The heating indicator ﬂashes rapidly 5-times and then remains

illuminated.

The appliance heats for 2 hours at full output.

At the end of the 2hours, the appliance returns to standard op-

eration controlled by the temperature selector.

The boost function starts the following day, 45minutes before the

time for which you have programmed the 24h automatic function

to be activated.

OPERATION

Operation

ENGLISH

www.stiebel-eltron.com BHE Style | 15

Example:

You would like your bathroom to be heated to the required tem-

perature by 07:00h.

 On day one, activate the 24h automatic function at 07:00h.

The appliance will activate the boost function immediately. The

next day, the boost function automatically starts at 06:15h in order

to heat up the bathroom for 07:00h.

Interrupting

You can interrupt the boost function at any time without changing

the start time.

 Hold down the boost function button for approximately

5seconds.

The heating indicator ﬂashes twice rapidly.

On the following day the boost function will start again at the

usual start time.

Deactivating

 Hold down the boost function button and press the ON/OFF

button twice.

The heating indicator ﬂashes slowly 3-times.

Changing the start time

 Hold down the boost function button and press the ON/OFF

button twice.

The heating indicator ﬂashes slowly 3-times. The 24h automatic

function is disabled.

 Re-activate the 24h automatic function at the required start

time. Hold down the boost function button and press the ON/

OFF button twice.

4.3 Frost protection

The appliance features a frost protection function to ensure that

the room temperature does not fall below 6°C during a prolonged

period of absence.



To enable the frost protection function, leave the appliance on

and turn the temperature selector to the frost protection setting.

4.4

Operation within a DHW/central heating system

!

Material losses

Only operate the direct heater rod when the radiator has

been ﬁlled.

Winter mode

The DHW/central heating system is running. You can control the

appliance temperature via the thermostatic valve installed on site.

Summer mode

When the DHW/central heating system is off the appliance is op-

erated via an integral electric direct heater rod. You can start the

boost and the 24h automatic function via the user interface.

4.4.1 Switching between winter and summer mode

Changing from winter to summer mode

 Close the thermostatic valve installed on site.

1/4h

1/2h 1h

2h

26�07�80�0003

2

1

1 ON indicator for the direct heater rod

2 ON/OFF switch for the direct heater rod

 Press the ON/OFF switch for the direct heater rod to switch it

on.

The ON indicator for the direct heater rod lights up.

Changing from summer to winter mode

 Press the ON/OFF switch for the direct heater rod to switch it

off.

The ON indicator for the direct heater rod goes off.

 Press the ON/OFF button to turn the appliance off.

The ON/OFF indicator goes off. You can control the appliance tem-

perature exclusively via the thermostatic valve installed on site.

Set the thermostatic valve installed on site to the required tem-

perature.

4.5 Shutting down

 Switch the appliance off by pressing the ON/OFF button for

the user interface.

The ON/OFF indicator goes off.

 Pull the mains plug out of the wall socket.

 If you are operating the appliance within a hot water heating

system, close the thermostatic valve installed on site.

4.6 Childprooﬁng

To prevent any unwanted appliance operation, you can lock the

temperature selector or limit its setting range.

 Turn the temperature selector to the required setting.

D0000041744

 Lever off the temperature selector using a small screwdriver.

OPERATION

Cleaning, care and maintenance

16 | BHE Style www.stiebel-eltron.com

Locking the temperature selector

D0000041743

1

2

1 Retainer for contact pieces

2 Contact piece placed in the setting range

 Remove one of the contact pieces from its retainer using a

cutting tool and position it as shown.

Limiting the setting range

D0000041741

 Remove both contact pieces from their retainer using a cut-

ting tool.

D0000041742

 Position the contact pieces, with one at each end of the re-

quired setting range.

 Replace the temperature selector.

5. Cleaning, care and maintenance

Note

Avoid abrasive or corrosive cleaning products.

Clean the surfaces when cold, using a soft cloth and ordinary

cleaning products.

6. Troubleshooting

Problem Cause Remedy

The heated air smells

unpleasant.

This can be caused by

dust during commis-

sioning.

The smell will dissipate within

a few minutes.

The appliance does

not heat up.

The MCB/fuse has re-

sponded/blown.

Replace the fuse/reset the

MCB.

The temperature sensor

is damaged (heating

indicator flashes 3 times

on start-up)

Call your qualified contractor.

The mains voltage to the

appliance is too high

(heating indicator flash-

es 5 times on start-up).

Switch the appliance off. Call

your qualified contractor.

The appliance heats

continuously.

The appliance is subject

to a continuous draught.

Remedy the cause of the

draught.

The temperature setting

was changed.

Set the required room tem-

perature at the temperature

selector

.

There is a fault with the

power supply.

Disconnect the appliance

from the power supply for

10minutes and then switch it

back on. If the problem occurs

regularly, arrange for your

power supply utility to check

the power supply.

The 24h automatic

function is not work-

ing.

There was a power

failure.

Set the 24h automatic func-

tion again.

The clocks have changed

to summer/wintertime.

Set the 24h automatic func-

tion again.

The elements at the

very top and bottom

don't get as warm as

the rest of the appli-

ance.

The elements at the

top are not completely

filled.

The heating medium expands

when it gets warm. It takes

a little longer for these ele-

ments to heat up.

Dirty marks appear

on the wall around

the appliance.

D

irty marks are caused

by contaminat

ed air

(candles, cigarette

smoke, poor ventilation,

etc.).

Avoid contaminating the in-

door air.

The boost function is

terminated prema-

turely

The room temperature

is too high. For safety

reasons, the appliance

has automatically

switched off the rapid

heater prematurely.

Switch the appliance off. Wait

at least 10 minutes before

switching the appliance back

on.

If you cannot remedy the fault, notify your qualiﬁed contractor.

To facilitate and speed up your request for assistance, provide the

number from the type plate (000000-0000-000000).

The type plate is located at the bottom, on the right hand side of

the appliance.

ENGLISH

www.stiebel-eltron.com BHE Style | 17

INSTALLATION

Safety

INSTALLATION

7. Safety

Only a qualiﬁed contractor should carry out installation, commis-

sioning, maintenance and repair of the appliance.

7.1 General safety instructions

We guarantee trouble-free function and operational reliability only

if original accessories and spare parts intended for the appliance

are used.

7.2 Instructions, standards and regulations

Note

Observe all applicable national and regional regulations

and instructions.

8. Appliance description

8.1 Standard delivery

The following are delivered with the appliance:

- Wall mounting bracket with ﬁxing materials

- 2 bathrobe hooks

The appliance is delivered fully wired.

9. Installation

!

Material losses

For integration into a DHW/central heating system, drain

the heat transfer medium supplied at the factory before

installing the appliance.

 To do this, remove the caps from the appliance's

ﬂow and return connectors.

Due to the weak concentration, you can dispose of the

heat transfer medium in the domestic sewer system.

Note

If operated as a purely electrical appliance, carry out

installation without connecting the ﬂow and return con-

nectors to the DHW / central heating system.

9.1 Installation site

!

Material losses

Observe th

e minimum clearanc

es in chapter "Speciﬁca-

tion".

!

Material losses

Fit the appliance to a vertical wall that is temperature-re-

sistant to at least 80°C.

!

Material losses

Never install the appliance directly below a wall socket.

Note

When integrating the appliance into a DHW / central heat-

ing system, choose the installation site subject to existing

on-site water connections.

9.2 Wall mounting

B

C

A

D0000041178

A 1599

B 400

C >320

 Drill the holes and insert rawl plugs.

D0000048233

1

45

32

1 Retainer screw

2 Wall sleeve

3 Lock screw

4 Retainer

5 Cap

 Secure the wall sleeves and the washers with screws.

 Fit the retainers to the rungs. Don't tighten the retainers yet.

18 | BHE Style www.stiebel-eltron.com

INSTALLATION

Troubleshooting

D0000048234

 Guide the retainers into the wall sleeves to join the appliance

to the wall.

 Align the appliance.

 Tighten the retainer screws and the lock screws.

9.3 Hydraulic connection (when integrating into a

DHW/central heating system)

Note

Observe the dimensions and minimum clearances in

chapter "Speciﬁcation".

 Integrate the appliance into the DHW / central heating system

by connecting the ﬂow and return connectors to the on-site

water connections.

 Connect a thermostatic valve at the ﬂow connector.

 When ﬁlling the appliance, bleed it using the air vent valve.

9.4 Fitting the bathrobe hooks

D0000048235

1 32

1 Bathrobe hook

2 Washer

3 Bathrobe hook backplate

 Fit the bathrobe hooks as shown.

9.5 Power supply

WARNING Electrocution

In wet rooms such as shower rooms and kitchens, install

the ﬂush box at least 25cm above the ﬂoor.

WARNING Electrocution

Never operate the appliance with an extension cable or

by connecting it to a multiple socket.

!

Material losses

Ensure the appliance can be separated from the power

supply by an isolator that disconnects all poles with at

least 3mm contact separation. For this, use contactors,

mains isolators, fuses, etc. Installation with a permanent

power cable is not permitted.

!

Material losses

Observe the type plate. The speciﬁed voltage must match

the mains voltage.

Note

Carry out all electrical connection and installation work

in accordance with national and regional regulations.

Note

Ensure a standard socket or junction box for a permanent

power supply is installed at a distance of at least 10cm

from the side of the appliance.

10. Troubleshooting

The power cable must only be replaced by a qualiﬁed contractor

using original spare parts.

11. Appliance handover

 Explain the functions of the appliance to the user.

 Draw special attention to the safety instructions.

 Hand the operating and installation instructions to the user.

ENGLISH

www.stiebel-eltron.com BHE Style | 19

INSTALLATION

Specication

12. Speciﬁcation

12.1 Dimensions

1695

1599

555

110 - 130

≥320

e07

i13

50

21,1

e18

e19

228,5

400

D0000047876

BHE 100 Style

e07 Ventilation Female thread G 1/2

e18 Flow Female thread G 1/2

e19 Return Female thread G 1/2

i13 Wall mounting bracket

12.2 Minimum clearances

≥150

≥200

≥150 ≥150

A

D0000048232

A >320mm

12.3 Data table

BHE 100 Style

233859

Heating output

Heating output to EN442 (75/65 – 20°C) W 827

Heating output F/R – T (70/55 – 24°C) W 598

Heating output F/R – T (50/40 – 24°C) W 282

Electrical data

Power connection 1/N ~ 230/240 V

Connected load kW 1

Output, direct heater rod kW 1

Output, rapid heater kW

Dimensions

Height mm 1695

Width mm 555

Depth mm 115

Weights

Weight kg 34

Versions

Frost protection setting °C 6

IP rating IP24

Safety category II

Colour Traffic white, RAL 9016

Connections

Connection, heating flow/return G 1/2

Values

Fill level, heat transfer medium l 8,734

Max. permissible inlet temperature °C 90

Max. operating pressure MPa 0.3

Setting range °C 6-30

Page is loading ...

РУССКИЙ

www.stiebel-eltron.com BHE Style | 47

Гарантия

Приборы, приобретенные за пределами Германии, не под-

падают под условия гарантии немецких компаний. К тому

же в странах, где продажу нашей продукции осуществляет

одна из наших дочерних компаний, гарантия предоставля-

ется исключительно этой дочерней компанией. Такая га-

рантия предоставляется только в случае, если дочерней

компанией изданы собственные условия гарантии. За пре-

делами этих условий никакая гарантия не предоставляется.

На приборы, приобретенные в странах, где ни одна из

наших дочерних компаний не осуществляет продажу

нашей продукции, никакие гарантии не распространяют-

ся. Это не затрагивает гарантий, которые могут предостав-

ляться импортером.

Защита окружающей среды и

утилизация

Внесите свой вклад в охрану окружающей среды. Утили-

зацию использованных материалов следует производить

в соответствии с национальными нормами.

Guarantee

The guarantee conditions of our German companies do not

apply to appliances acquired outside of Germany. In countries

where our subsidiaries sell our products a guarantee can only

be issued by those subsidiaries. Such guarantee is only grant-

ed if the subsidiary has issued its own terms of guarantee. No

other guarantee will be granted.

We shall not provide any guarantee for appliances acquired in

countries where we have no subsidiary to sell our products.

This will not aect warranties issued by any importers.

Environment and recycling

We would ask you to help protect the environment. After use,

dispose of the various materials in accordance with national

regulations.

Garantie

Les conditions de garantie de nos sociétés allemandes ne

s’appliquent pas aux appareils achetés hors d’Allemagne. Au

contraire, c’est la liale chargée de la distribution de nos pro-

duits dans le pays qui est seule habilitée à accorder une garan-

tie. Une telle garantie ne pourra cependant être accordée que

si la liale a publié ses propres conditions de garantie. Il ne sera

accordé aucune garantie par ailleurs.

Nous n’accordons aucune garantie pour les appareils achetés

dans des pays où aucune liale de notre société ne distribue

nos produits. D’éventuelles garanties accordées par l’importa-

teur restent inchangées.

Environnement et recyclage

Merci de contribuer à la préservation de notre environnement.

Après usage, procédez à l’élimination des matériaux conformé-

ment à la réglementation nationale.

Garantie

Voor toestellen die buiten Duitsland zijn gekocht, gelden de

garantievoorwaarden van onze Duitse ondernemingen niet.

Bovendien kan in landen waar één van onze dochtermaat-

schappijen verantwoordelijk is voor de verkoop van onze

producten, alleen garantie worden verleend door deze doch-

termaatschappij. Een dergelijk garantie wordt alleen verstrekt,

wanneer de dochtermaatschappij eigen garantievoorwaarden

heeft gepubliceerd. In andere situaties wordt er geen garantie

verleend.

Voor toestellen die in landen worden gekocht waar wij geen

dochtermaatschappijen hebben die onze producten verkopen,

verlenen wij geen garantie. Een eventueel door de importeur

verzekerde garantie blijft onverminderd van kracht.

Milieu en recycling

Wij verzoeken u ons te helpen ons milieu te beschermen. Doe

de materialen na het gebruik weg overeenkomstig de natio-

nale voorschriften.

GUARANTEE | ENVIRONMENT AND RECYCLING



Deutschland

STIEBEL ELTRON GmbH & Co. KG

Dr.-Stiebel-Straße 33 | 37603 Holzminden

Tel. 05531 702-0 | Fax 05531 702-480

[email protected]

www.stiebel-eltron.de

Verkauf Tel. 05531 702-110 | Fax 05531 702-95108 | [email protected]

Kundendienst Tel. 05531 702-111 | Fax 05531 702-95890 | [email protected]

Ersatzteilverkauf Tel. 05531 702-120 | Fax 05531 702-95335 | [email protected]

Irrtum und technische Änderungen vorbehalten! | Subject to errors and technical changes! | Sous réserve

d‘erreurs et de modifications techniques! | Onder voorbehoud van ver

g

issin

g

en en technische wi

j

zi

g

in

g

en! |

Salvo error o modificación técnica! | Excepto erro ou alteração técnica | Zastrzeżone zmian

y

techniczne i

ewentualne błędy | Omyly a technické změny jsou vyhrazeny! | A muszaki változtatások és tévedések

j

o

g

át

fenntartjuk! |

Отсутствие ошибок не гарантируется. Возможны технические изменения.

| Ch

y

b

y

a

technické zmeny sú vyhradené! Stand 9147

Australia

STIEBEL ELTRON Australia Pty. Ltd.

6 Prohasky Street | Port Melbourne VIC 3207

Tel. 03 9645-1833 | Fax 03 9645-4366

[email protected]

www.stiebel.com.au

Austria

STIEBEL ELTRON Ges.m.b.H.

Gewerbegebiet Neubau-Nord

Margaritenstraße 4 A | 4063 Hörsching

Tel. 07221 74600-0 | Fax 07221 74600-42

[email protected]

www.stiebel-eltron.at

Belgium

STIEBEL ELTRON bvba/sprl

't Hofveld 6 - D1 | 1702 Groot-Bijgaarden

Tel. 02 42322-22 | Fax 02 42322-12

[email protected]

www.stiebel-eltron.be

China

STIEBEL ELTRON (Guangzhou) Electric

Appliance Co., Ltd.

Rm 102, F1, Yingbin-Yihao Mansion, No. 1

Yingbin Road

Panyu District | 511431 Guangzhou

Tel. 020 39162209 | Fax 020 39162203

info@stiebeleltron.cn

www.stiebeleltron.cn

Czech Republic

STIEBEL ELTRON spol. s r.o.

K Hájům 946 | 155 00 Praha 5 - Stodůlky

Tel. 251116-111 | Fax 235512-122

[email protected]

www.stiebel-eltron.cz

Finland

STIEBEL ELTRON OY

Kapinakuja 1 | 04600 Mäntsälä

Tel. 020 720-9988

[email protected]

www.stiebel-eltron.fi

France

STIEBEL ELTRON SAS

7-9, rue des Selliers

B.P 85107 | 57073 Metz-Cédex 3

Tel. 0387 7438-88 | Fax 0387 7468-26

[email protected]

www.stiebel-eltron.fr

Hungary

STIEBEL ELTRON Kft.

Gyár u. 2 | 2040 Budaörs

Tel. 01 250-6055 | Fax 01 368-8097

[email protected]

www.stiebel-eltron.hu

Japan

NIHON STIEBEL Co. Ltd.

Kowa Kawasaki Nishiguchi Building 8F

66-2 Horikawa-Cho

Saiwai-Ku | 212-0013 Kawasaki

Tel. 044 540-3200 | Fax 044 540-3210

[email protected]

www.nihonstiebel.co.jp

Netherlands

STIEBEL ELTRON Nederland B.V.

Daviottenweg 36 | 5222 BH 's-Hertogenbosch

Tel. 073 623-0000 | Fax 073 623-1141

[email protected]

www.stiebel-eltron.nl

Poland

STIEBEL ELTRON Polska Sp. z O.O.

ul. Działkowa 2 | 02-234 Warszawa

Tel. 022 60920-30 | Fax 022 60920-29

[email protected]

www.stiebel-eltron.pl

Russia

STIEBEL ELTRON LLC RUSSIA

Urzhumskaya street 4,

building 2 | 129343 Moscow

Tel. 0495 7753889 | Fax 0495 7753887

[email protected]

www.stiebel-eltron.ru

Slovakia

TATRAMAT - ohrievače vody s.r.o.

Hlavná 1 | 058 01 Poprad

Tel. 052 7127-125 | Fax 052 7127-148

[email protected]

www.stiebel-eltron.sk

Switzerland

STIEBEL ELTRON AG

Industrie West

Gass 8 | 5242 Lupfig

Tel. 056 4640-500 | Fax 056 4640-501

[email protected]

www.stiebel-eltron.ch

Thailand

STIEBEL ELTRON Asia Ltd.

469 Moo 2 Tambol Klong-Jik

Amphur Bangpa-In | 13160 Ayutthaya

Tel. 035 220088 | Fax 035 221188

info@stiebeleltronasia.com

www.stiebeleltronasia.com

United Kingdom and Ireland

STIEBEL ELTRON UK Ltd.

Unit 12 Stadium Court

Stadium Road | CH62 3RP Bromborough

Tel. 0151 346-2300 | Fax 0151 334-2913

[email protected]

www.stiebel-eltron.co.uk

United States of America

STIEBEL ELTRON, Inc.

17 West Street | 01088 West Hatfield MA

Tel. 0413 247-3380 | Fax 0413 247-3369

[email protected]

www.stiebel-eltron-usa.com

A 314172-39889-9235

4<AMHCMO=bebhcd>

STIEBEL ELTRON BHE Style Operation Instruction

Related papers

Other documents