Aaeon GENE-9455 Rev.B User manual

SubCompact Board GENE-9455 Rev.B

GENE-9455 Rev.B

Intel

® AtomTM N270 Processor

With LVDS, Ethernet,

1 Mini PCI, 1 Mini Card,

6 USB2.0, 4 COM, 1 Parallel

AC97 2.3 Codec 2CH Audio

GENE-9455 Manual Rev. B 1st Ed.

August 2010

SubCompact Board GENE-9455 Rev.B

i

Copyright Notice

This document is copyrighted, 2010. All rights are reserved. The

original manufacturer reserves the right to make improvements to the

products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated, or

transmitted in any form or by any means without the prior written

permission of the original manufacturer. Information provided in this

manual is intended to be accurate and reliable. However, the original

manufacturer assumes no responsibility for its use, or for any in-

fringements upon the rights of third parties that may result from its

use.

The material in this document is for product information only and is

subject to change without notice. While reasonable efforts have been

made in the preparation of this document to assure its accuracy,

AAEON assumes no liabilities resulting from errors or omissions in

this document, or from the use of the information contained herein.

AAEON reserves the right to make changes in the product design

without notice to its users.

SubCompact Board GENE-9455 Rev.B

ii

Acknowledgments

All other products’ name or trademarks are properties of their

respective owners.

z Award is a trademark of Award Software International, Inc.

z CompactFlash™ is a trademark of the Compact Flash

Association.

z Intel®, Atom™ are trademarks of Intel® Corporation.

z Microsoft Windows® is a registered trademark of Microsoft Corp.

z ITE is a trademark of Integrated Technology Express, Inc.

z IBM, PC/AT, PS/2, and VGA are trademarks of International

Business Machines Corporation.

z SoundBlaster is a trademark of Creative Labs, Inc.

Please be notified that all other products’ name or trademarks not be

mentioned above are properties of their respective owners.

SubCompact Board GENE-9455 Rev.B

iii

Packing List

Before you begin installing your card, please make sure that the

following materials have been shipped:

• GENE-9455 Rev.B CPU Card

• Quick Installation Guide

• CD-ROM for manual (in PDF format) and drivers

• Cooler or Heatsink

• 1700060157 Keyboard/ Mouse Cable

• 9657666600 Jumper Cap

If any of these items should be missing or damaged, please

contact your distributor or sales representative immediately.

SubCompact Board GENE-9455 Rev.B

iv

Contents

Chapter 1 General Information

1.1 Introduction................................................................1-2

1.2 Features....................................................................1-3

1.3 Specifications............................................................1-4

Chapter 2 Quick Installation Guide

2.1 Safety Precautions....................................................2-2

2.2 Location of Connectors and Jumpers .......................2-3

2.3 Mechanical Drawing..................................................2-5

2.4 List of Jumpers.......................................................... 2-7

2.5 List of Connectors .....................................................2-8

2.6 Setting Jumpers ........................................................2-10

2.7 COM2 Ring/+5V/+12V Selection (JP1).....................2-11

2.8 Clear CMOS (JP2) ....................................................2-11

2.9 AT/ATX Power Mode Selection (JP3).......................2-11

2.10 LVDS Inverter Voltage Selection (JP4)...................2-11

2.11 LVDS Operating Voltage Selection (JP5)...............2-11

2.12 External +5V Standby Power Input & PS ON# (CN1)

.........................................................................................2-12

2.13 Digital I/O Connector (CN2)....................................2-12

2.14 Parallel Port Connector (CN3) ................................2-13

2.15 TV-Out Connector (CN4) ........................................2-13

2.16 COM Port 2 Connector (CN5).................................2-13

2.17 COM Port 3 Connector (CN6).................................2-14

SubCompact Board GENE-9455 Rev.B

v

2.18 2nd LVDS Connector for 18/24-bit LCD (CN7) ........2-15

2.19 Onboard BIOS Programming I/F(CN8)(Optional)...2-15

2.20 COM Port 4 Connector (CN9).................................2-16

2.21 UIM Connector (CN10) ...........................................2-16

2.22 USB Port 1 Connector (CN11)................................2-16

2.23 1st LVDS Connector for 18-bit LCD (CN12)............2-16

2.24 USB Port 2 Connector (CN13)................................2-17

2.25 USB Port 3 Connector (CN14)................................2-17

2.26 USB Port 4 Connector (CN15)................................2-18

2.27 2nd LVDS Inverter Connector (CN16)......................2-18

2.28 Front Panel (CN17).................................................2-18

2.29 1st LVDS Inverter Connector (CN18).......................2-18

2.30 Keyboard/Mouse Connector (CN19).......................2-19

2.31 SATA 1 Connector (CN20)......................................2-19

2.32 +12V Power Input Connector (CN21).....................2-19

2.33 RJ-45 Ethernet #1 Connector (CN22).....................2-19

2.34 RJ-45 Ethernet #2 Connector (CN23).....................2-20

2.35 USB Port 5 & 6 Connector (CN24)..........................2-20

2.36 +5V Standby Power Output w/PS_ON# & SMBUS

(CN25).............................................................................2-20

2.37 Audio Inp/Out CD In and MIC Connector (CN26)...2-21

2.38 +5V Output Connector (CN27)................................2-21

2.39 System Fan Connector (CN28)...............................2-21

2.40 CRT Display Connector (CN30)..............................2-22

2.41 COM Port 1 Connector (CN31)...............................2-22

SubCompact Board GENE-9455 Rev.B

vi

2.42 Mini-Card Slot (CN32).............................................2-22

2.43 CompactFlash Disk (CFD1)....................................2-23

2.44 Mini-PCI Slot (MPC1)..............................................2-24

2.45 DDR2 SODIMM Slot (DIMM 1) ...............................2-24

Chapter 3 Award BIOS Setup

3.1 System Test and Initialization. ..................................3-2

3.2 Award BIOS Setup....................................................3-3

Chapter 4 Driver Installation

4.1 Installation.................................................................4-3

Appendix A Programming The Watchdog Timer

A.1 Programming .........................................................A-2

A.2 ITE8781 Watchdog Timer Initial Program..............A-6

Appendix B I/O Information

B.1 I/O Address Map....................................................B-2

B.2 1st MB Memory Address Map ................................B-3

B.3 IRQ Mapping Chart................................................B-4

B.4 DMA Channel Assignments...................................B-4

Appendix C Mating Connector

C.1 List of Mating Connectors and Cables.................. C-2

SubCompact Board GENE-9455 Rev.B

Chapter 1 General Information 1- 1

General

Chapter

1

Information

SubCompact Board GENE-9455 Rev.B

1.1 Introduction

AAEON, a leading embedded boards manufacturer, is pleased to

announce the debut of their new generation 3.5” SubCompact

Board—GENE-9455 Rev.B.

GENE-9455 Rev.B adopts Intel® AtomTM N270 Processor. The

system memory is deployed with 200-pin SODIMM DDR2 400/533

up to 2GB. In addition, Intel® 82574L supports two

10/100/1000Base-TX that allows a faster network connections.

This model applies a Mini-PCI socket and one Mini Card for

flexible expansions. Moreover, six USB2.0, one SATA 1 and one

CompactFlashTM provide a better storage. Three RS-232, one

RS-232/422/485 and 8-bit digital I/O are configured on the

GENE-9455 Rev.B as well. Full functions make GENE-9455

Rev.B user friendly. With the GENE-9455 Rev.B, there are no

more worries about installing many necessary devices to complete

the functions of your system.

The display of GENE-9455 Rev.B supports CRT/LCD, CRT/TV,

LCD/TV, simultaneous and dual view displays, and is up to 24-bit

dual-channel LVDS. Furthermore, this brand new SubCompact

board is developed to cater to the requirements of Automation,

Medical, ticket machine, transportation, gaming, KIOSK, and

POS/POI applications.

Chapter 1 General Information 1- 2

SubCompact Board GENE-9455 Rev.B

1.2 Features

z Onboard Intel® Atom™ N270 Processor

z Intel® 945GSE + ICH7M

z SODIMM DDR2 400/533, Max. 2 GB

z Gigabit Ethernet x 2

z CRT, Dual LVDS LCDs: 18-bit Dual-Channel LVDS LCD +

24-bit Dual-Channel LVDS LCD, TV

z AC97 2.3 Codec 2CH Audio

z SATA I x 1, CompactFlash™ x 1

z USB2.0 x 6, COM x 4, Parallel x 1, 8-bit Digital I/O

z Mini-PCI x 1, Mini Card x 1

z +12V Only Operation

z Onboard Trusted Platform Module (Optional)

Chapter 1 General Information 1 - 3

SubCompact Board GENE-9455 Rev.B

1.3 Specifications

System

z Processor Intel® Atom™ N270 processor

up to 1.6 GHz with FSB 533

MHz

z System Memory 200-pin SODIMM DDR2

400/533 x 1, Max. 2GB

z Chipset Intel

® 945GSE+ICH7M

z I/O Chipset ITE 8781

z Ethernet Intel® 82574L,

10/100/1000Base-TX, RJ-45 x 2

z BIOS Award Plug & Play SPI BIOS –

2 MB Flash

z Wake On LAN Yes

z Watchdog Timer Generates a time-out system

reset

z H/W Status Monitoring Supports power supply

voltages, and temperature

monitoring

z Expansion Interface Mini-PCI x 1, Mini Card x 1

z Power Requirement +12V, AT/ATX

z Trusted Platform Infineon SLB 9635 TT 1.2

Module (TPM) (Optional)

z Battery Lithium battery

Chapter 1 General Information 1- 4

SubCompact Board GENE-9455 Rev.B

z Power Consumption Intel® Atom™ N270, DDRII 667

2GB, 1.55A @ +12V

z Board Size 5.75”(L) x 4”(W) (146mm x

101.6mm)

z Operating Temperature 32˚F~ 140˚F (0˚C ~ 60˚C)

z Storage Temperature -40˚F~ 176˚F (-40˚C ~ 80˚C)

z Operating Humidity 0%~90% relative humidity,

non-condensing

z MTBF (Hours) 70,000

Display: Supports CRT/LCD, CRT/TV,LCD/TV, simultaneous

l view displays and dua

z Chipset Intel® 945GSE integrated

z Memory Shared system memory up to

224MB w/ DVMT 3.0

z LCD Interface Dual LVDS LCDs: 18-bit

Dual-channel LVDS LCD +

24-bit Dual-channel LVDS LCD

z Resolution Up to 1920 x 1440 for CRT

Up to 1920 x 1200 for LCD

z TV-out Supports NTSC & PAL

Standards S-terminal and

Composite Video

Chapter 1 General Information 1 - 5

SubCompact Board GENE-9455 Rev.B

I/O

z Storage SATA 1 x 1, Type 2

CompactFlash™ x 1

z Serial Port RS-232 x 3, RS-232/422/485 x 1

z Parallel Port SPP/EPP/ECP x 1

z USB Port USB2.0 x 6

z PS/2 Port Keyboard x 1, Mouse x 1

z Digital I/O Supports 8-bit (Programmable)

z Audio MIC-in, Line-in, Line-out, CD-in

Chapter 1 General Information 1- 6

SubCompact Board GENE-9455 Rev.B

Chapter 2 Quick Installation Guide 2-1

Quick

Installation

Chapter

2

Guide

Notice:

The Quick Installation Guide is derived

from Chapter 2 of user manual. For other

chapters and further installation

instructions, please refer to the user

manual CD-ROM that came with the

product.

Part No. 2007945530 Printed in Taiwan August 2010

SubCompact Board GENE-9455 Rev.B

Chapter 2 Quick Installation Guide 2-2

2.1 Safety Precautions

Always completely disconnect the power cord

from your board whenever you are working on

it. Do not make connections while the power is

on, because a sudden rush of power can

damage sensitive electronic components.

Always ground yourself to remove any static

charge before touching the board. Modern

electronic devices are very sensitive to static

electric charges. Use a grounding wrist strap at

all times. Place all electronic components on a

static-dissipative surface or in a static-shielded

bag when they are not in the chassis

SubCompact Board GENE-9455 Rev.B

Chapter 2 Quick Installation Guide 2-3

2.2 Location of Connectors and Jumpers

Component Side

CN19

CN23

CN22

CN20

JP4

CN27

CN30

CN8

MPCI1

CN17

CN21

CN1

CN4

CN3

CN12

CN16

CN24

CN2

CN15

CN14

CN13

CN11

CN9

CN7

CN28

CN31

CN25

JP5

CN5

JP1

JP3

JP2

BAT1

CN6

CN10

CN26

CN18

SubCompact Board GENE-9455 Rev.B

Solder Side

DIMM1

CFD1

CN32

Chapter 2 Quick Installation Guide 2-4

SubCompact Board GENE-9455 Rev.B

Chapter 2 Quick Installation Guide 2-5

2.3 Mechanical Drawing

Component Side

(12.55)

(13.35)

(17.30)

(1.80)

(6.50)

(8.70)

0.00

2.02

3.79

8.89

3.22

18.31

23.19

40.74

59.26

84.07

121.92

142.82

30.14

38.50

46.83

55.14

63.43

76.77

90.05

62.78

71.68

7.00

79.06

83.26

89.55

98.38

8.89

2.07

6.68

22.49

50.76

61.06

82.04

45.40

65.40

71.13

91.13

89.46

136.14

142.85

101.61

146.05

54.70

19.69

9.32

117.81

69.66

86.97

31.93

13.95

29.74

21.45

4.08

99.50

26.49

21.28

104.24

142.87

8.87

102.55

7.25

88.03

12.01

73.41

13.70

76.45

99.19

3.84

68.74

74.73

16.89

5.99

98.36 98.38

SubCompact Board GENE-9455 Rev.B

Chapter 2 Quick Installation Guide 2-6

Solder Side

0.00

11.94

32.11

57.11

67.39

25.76

65.94

139.90

92.05

25.25

SubCompact Board GENE-9455 Rev.B

Chapter 2 Quick Installation Guide 2-7

2.4 List of Jumpers

The board has a number of jumpers that allow you to configure your

system to suit your application.

The table below shows the function of each of the board's jumpers:

Jumpers

Label Function

JP1 COM2 RI/+5/+12V Selection

JP2 Clear CMOS Front Panel

JP3 AT/ATX Power Mode Selection

JP4 LVDS Inverter Voltage Selection

JP5 LVDS Operating Voltage Selection

Page is loading ...

Aaeon GENE-9455 Rev.B User manual

Related papers

Other documents