Amroad AMROAD P3 Technical Manual

AMROAD P3

DOOR STATION

~

Technical Manual

AMROAD P3

Contents

Contents .............................................. i

Preface ................................................ 1

Front Panel ......................................... 2

Door bell using & Audio

Announcement ................................... 3

Issue RFID card ................................... 4

Issue RFID Master Card ................................. 4

Issue New Card .............................................. 4

RFID LED Indicator ......................................... 4

Status Indicator .................................. 5

Status LED ..................................................... 5

Functions Performed by the IP-PBX .... 6

Simultaneous Ring ........................................ 6

Call Forwarding ............................................. 6

E-Mail/Voicemail Notification ...................... 6

WEB UI ................................................ 7

Search Tool .....................................................7

WEB UI login ...................................................7

Outline of WEB UI Settings ................. 8

System ................................................ 9

Basic Setting .................................................. 9

Network Setting ........................................... 10

Login Name .................................................... 11

Reboot ........................................................... 11

Streaming Setting ..............................12

Video ............................................................. 12

Audio............................................................. 14

SIP Settings ....................................... 15

Entrance Settings ............................... 17

Extensions .................................................... 18

GPIO ............................................................. 20

RFID ............................................................... 22

Upgrade ............................................ 23

Update .......................................................... 23

Configurations ..............................................25

AR APS – Engineering MODE ...................... 26

IO Application .................................. 27

Electric Bolt .................................................. 27

Electric Strike ............................................... 28

PIR Motion Sensor and Light ....................... 29

Regulations and Safety Precautions .. 30

FCC Statement ............................................ 30

FCC Radiation Exposure Statement ........... 30

EC Directive Compliance Statement .......... 30

Contents

i

AMROAD P3

Preface

Welcome

Thank you for choosing this Door Station. This

device is designed to work as Door Station of

inside large building to form a SIP-based door

entry system. Besides taking advantages of IP

technologies, this device links to other SIP

devices. It will work with most IP PBX systems

supporting audio and video, and it can be

configured via a web interface.

Certificates, Certify your safety

AMROAD full range products passed European

CE, USA FCC, BSMI/NCC Taiwan. All these

certificates promise tenants a harmless

modern living environment.

No Electric devices will be interfered with this

product.

Main Feature

 Talk to visitors with real time video and

voice on IP Video Phone or Video Indoor

Station

 SIP 2.0 (RFC3261) Compliant

 Support H.263 video format.

 Support G.711 audio formats.

 RFID card reader (ISO14443A/13.56MHz

(MIFARE Standard) with embedded RFID

card database

 Support Peer-to-Peer Mode

 Build-in wide angle lens

 Wall Lamp (White LEDs)

 Build-in speaker and microphone.

 Scan RFID card to arm security

 Support PoE (Power over Ethernet,

802.3af) module (External power supply

AC 48V In)

 Web user interface for configuration and

management.

NOTICE

The default of this device is DHCP. If you need

to set Static IP, please reference Reset Button in

Installation Manual.

The device will be switched to the static IP

mode and reboot itself when the user has

pressed the reset button for 3 seconds. IP is

"192.168.0.50".

Preface

1

AMROAD P3

Front Panel

Door bell

Lens Module

RFID reader

Speaker

Wall Lamp

Microphone

Status LED

2

AMROAD P3

Door bell using & Audio Announcement

Door bell using

1. Making Calls From Door Station

Using the Door Station is quite easy. You

will see “Door bell” on the front side.

Press “Door Bell” button to make a call.

White LED lights on the top of device will

brighten.

2. Waiting for the reply from indoor, it can

combine with the function the indoor

device has.

The function includes microphone,

camera lens, speaker, RELAY, RFID reader.

So it can provide video intercom and

Electric door unlock.

Audio Announcement

According to some specific situation, AMROAD

P3 will play the audio announcement below,

specially scan the card and security.

 Please Scan Your New Card – scanning

Master RFID Card on RFID scanning zone

and user is ready to issue new card.

 Your New Card has been Added – new

card is registered.

 Fail to Add Your New Card – new card is

rejected to be registered.

 The Door Is Not Closed – resident’s door

is not closed well. Resident should have

installed Electric Door Lock and

detector-magnetic switch.

 Video Phone Is Tampered – resident’s door

hone is damaged by intrude. There is a

micro switch hidden behind front panel.

Door bell using & Audio Announcement

3

AMROAD P3

Issue RFID card

If you scan the RFID card, AMROAD P3 will

verify the information with the database to

determine whether to open the door or not.

Issue RFID Master Card

If AMROAD P3 have not set the Master card yet,

you can use an RFID card swipe become Master

Card.

We recommend that after the installation is

complete, brush on this card to complete the

opening card and produce Master RFID cards,

and you should keep it safe.

If you would like to reset a new Master Card,

please return to the factory default.

Issue New Card

Scan Master RFID Card on AMROAD P3 First.

Within 10 seconds, scan new RFID card on

AMROAD P3, AMROAD P3 will store new Card

number Into Database.

The new RFID card is authorized and can be

used to scan on RFID scanning zone and open

door.

RFID LED Indicator

The 3-color LED indicator is located under the

doorbell bottom for information and status of

scanning RFID card.

RED

Keep blinking – While RFID module is Out of

order.

Blink 3 times – RFID card is NOT accepted. (0.5

sec on, 0.5 sec off)

GREEN

Blink 3 times – Card is accepted. (0.5 sec on, 0.5

sec off)

BLUE

Blink 3 times – Scan Master RFID Card for the

first time to register Master RFID Card. If it is

successful, blue light twinkles 3 times. (0.5 sec

on, 0.5 sec off)

On for 10 seconds – Scan Master RFID Card to

Issue New card. After scanning Master RFID

Card, blue light will light for 10 seconds. Within

10 seconds, new RFID Card should be scanned

on RFID reader.

Issue RFID card

4

AMROAD P3

Status Indicator

Status LED

There is a 3-color LED lamp hiding below the

front panel on the right hand side. This is an

index for the status of AMROAD P3, and we can

follow this status to fix the problem.

GREEN LED

RED LED

BLUE LED

Description

OFF OFF OFF

Normal Condition(SIP

Mode)

OFF

ON for 1 sec

OFF

Boot is initiated.

Blinking

(3 sec ON, 1 sec OFF)

OFF OFF

Boot procedure 1st stage.

OS Initial.

OFF ON OFF

Boot procedure 2nd stage.

AP Ready.

Blinking

(green



blue



red)

Blinking

(green



blue



red)

Blinking

(green



blue



red)

Firmware Upgrade.

OFF OFF ON 5 sec once

Reset! Device becomes

Static IP mode.

Blinking 3 times

(0.5 sec ON, 0.5 sec

OFF)

OFF OFF

Press RESET button for 6

seconds to restore device to

its factory default setting.

OFF OFF

Blinking

(3 sec ON, 1 sec OFF) SIP is NOT registered.

OFF

Blinking

(3 sec ON, 1 sec OFF)

OFF Network is Disconnected.

OFF Blinking

(3 sec ON, 1 sec OFF) OFF

Network is connected, but

the device fails to obtain IP

address.

OFF

Blinking

(3 sec ON, 1 sec OFF)

OFF Alarm is triggered.

Status Indicator

Status LED

5

AMROAD P3

Functions Performed by the IP-PBX

Simultaneous Ring

The Distribution Policy is set to Ring All. e.g.

When a visitor calls the group call (say

extension 500), group members (say

extensions 155, 157, and 166) will all ring

simultaneously.

Call Forwarding

Enter a number to which incoming calls are

forwarded when unanswered. The number

could be an extension or a PSTN number with

appropriate outbound prefix.

E-Mail/Voicemail Notification

IP PBX has a built-in voice mail subsystem with

a sophisticated IVR menu. A call to an

extension unanswered could be configured to

enter voice mail recording procedure. After

leaving a message, a notification e-mail will be

sent to the user owns the extension with or

without the message in the form of an

attached WAV file.

Functions Performed by the IP-PBX

(Compatible with A

MROAD IP-PBX)

6

AMROAD P3

WEB UI

Search Tool

The default connection setting type of this

product is “DHCP Client”, it is a typical network

mode.

You can use AMROAD Configurator that we

supplied. This software utility provided by your

local distributor or local dealer which is able to

help you to find your Door Station when using

dynamic IP address.

When this application starts, Search Tool will

search all the AMROAD products automatically

in the same network. Choose the device which

you want to set, click on the right, and

Login Page will show.

WEB UI login

In addition to search the device by Search Tool,

you can input IP on browser, and Login Page

(WEB UI) will show as below.

WEB UI has protected by Login ID and Password.

Input correct ID and password, click “Login”

bottom and get into WEB UI. The detail setting

information will describe next page. Default ID

and password are “admin”.

NOTICE：

1. While configuring WEB UI (User Interface),

please do not operate this product so as

to prevent this product being out of order.

2. Do not input special symbols “, \, and & in

the fields on the WEB UI. Otherwise, you

may fail to save your setting normally.

3. After configuring some Web pages and

pressing “SAVE” button, you need to wait

a little longer for system to save the

configuration.

WEB UI

7

AMROAD P3

Outline of WEB UI Settings

System

 Basic Setting

 Network Setting

 Login Name

 Reboot

Streaming Setting

 Video

 Audio

SIP Setting

 Authentication

 SIP Proxy

 SIP Registrar Server

Entrance Setting

 Entrance

 GPIO

 RFID

Upgrade

 Upgrade

 Configurations

 AR APS

IO Application

 Electric Bolt

 Electric Strike

 PIR Motion Sensor

 Light

Outline of WEB UI Settings

8

AMROAD P3

System

Basic Setting

 Device ID：Device ID that assigned by

manufacturer.

 Date and Time：Here shows date and time

set on this Door Station.

 Set New Date and Time：These fields

allow user to set correct date and time

according to the local–standard. You may

synchronize phone time to match your PC

by pressing “Sync with PC” button.

 Time Zone：This field allows you to select

your time zone to fit your location. You

can enable the Daylight-Saving feature if

needed.

 Daylight Saving Time is a way of getting

more light out of the day by advancing

clocks by one hour during the summer.

 Network Time Protocol：Enable NTP

Calibration service to allow the system to

calibrate the time with NTP server

through Internet.

 NTP Server Address：You may use your

preferred NTP server by input new address

here.

 Language：Select “English” or “Traditional

Chinese” for language of Audio

Announcement.

 Save：Click to save your setting.

System

9

AMROAD P3

Network Setting

 MAC Address：This is a quasi-unique

identifier attached to most network

adapters.

 IP Type(The default value is DHCP Client.)

1. DHCP Client：The system will

automatically assign your Door

Station an IP address.

2. PPPoE：This allows you to set Internet

connection with ID Account and

Password.

NOTE：For PPPoE connection mode,

we suggest that bandwidth-128kbps

would have better video quality.

3. Static IP：You have to input IP address,

Subnet Mask, Default Gateway,

Primary DNS and Secondary DNS

data.

 Save：Click this button to save your setting.

System

10

AMROAD P3

Login Name

The default ID and password for system login

are admin and admin.

User may change his Login ID and Password on

the webpage by entering new Login ID and

Password.

Reboot

When user needs to reboot AMROAD P3

remotely, just click “Reboot” button on this

webpage starts this action. After confirm

rebooting, Web User Interface will back to the

home page, but the Door Station may take

30~60 seconds to restart its system.

NOTE：DO NOT operate the AMROAD P3 while

system is rebooted (reset).

System

11

AMROAD P3

Streaming Setting

Video

 Bandwidth：You may select preferred

bandwidth for video and audio streaming.

There are 4 options: 128Kbps, 256Kbps,

384Kbps, and 512Kbps.

 Codec Priority：

First－You may select the Video streaming

priority - H.263.；

Second－You may select the Video

streaming priority - H.263 or Disable.

Streaming Settings

12

AMROAD P3

 Power Line Frequency：You may select the

power frequency according to your local

power specifications. Wrong power

frequency may cause the video flicking

abnormally. Default setting is 60Hz.

 CMOS Static Brightness：This item allows

you to adjust the brightness of CMOS

according to the lighting environment of

the installed location. Higher value makes

the video brighter. When it set 2, it means

automatic detection

 CMOS Color Balance：This item allows you

to adjust the color of video. Select

according to the lighting environment：

Fluorescent Light, Yellow Lamps and

Orange Lamps.

Fluorescent Light – This condition is

suited for white lighting environment.

Yellow Lamps – This condition is suited

for indoor yellow bulb environment.

Orange Lamps – This condition is suited

for indoor orange color or more red color

environments.

 Save Click this button to save your setting.

Streaming Settings

13

AMROAD P3

Audio

 Code Priority：You may select the Audio

streaming priority – G.711.

 Scene：Select Disable, Enable or User

Define.

When “User Define” is selected, the

following two items appears：

1. Noise Threshold (db)：Default is -40.

The voice intensity that is lower than

the value (-40db) will be neglected.

(Acceptable value -40~-52)

2. Target Level (db)：Default is -23 The

voice intensity that is around normal

intensity will be processed to be the

value (-23db). (Acceptable value

-20~-32)

 VAD：You may enable or disable

Voice-Active-Detection function here. The

AMROAD P3 will detect background noise

and send silence packet to the other end if

this feature is enabled. This allows called

party to hear better audio quality.

 CNG：You may enable or disable

Comfortable-Noise-Generate function

here. The AMROAD P3 will generate

background noise when receiving silence

packet from the other end if this feature is

enabled. This allows called party to hear

better audio quality.

 Speaker Volume：This item allows you to

select volume of speaker. There are 10

levels, 0 ~ 9.

 Internal Alarm Volume：Select “High” to

turn Internal Alarm Volume Up, or select

“Low” to turn Internal Alarm Volume

Down.

 Save：

Click this button to save your setting.

Streaming Settings

14

AMROAD P3

SIP Settings

Authentication

 Display Name：Name, Recommendations

input “doorphone.”

NOTE：

Please enter “doorphone” in the field of Display

Name. When Door Bell is pressed, there will be

“Doorbell” sound, and enable function of

“Preview Picture” on AMROAD Home Station.

Assign the following information provided by

the switch：

 User Number：Extension Number.

 Account ID：You may fill in your account

name of SIP service in this field.

 Account Password：You may fill in the

password of your SIP service account.

SIP Settings

15

AMROAD P3

SIP Proxy Server

 Service：You may select “Enable” or

“Disable” the SIP Proxy Server in the

dropdown menu.

 IP Address：You may fill in the IP address of

SIP Registrar Server here.

NOTE： To enable the Peer-to-Peer mode,

the device selects Disable (Close) SIP Proxy

Server.

SIP Registrar Server

 IP Address：You may fill in the IP address of

SIP Registrar Server here.

 Registration Expire Time：Set the time for

SIP registration authorization the default is

3600 seconds.

 Media Timer (0~180)：While door machine

had not received any Media Packets from a

remote period of time, this setting allows

AMROAD P3 forcibly stopped talking.

Enter "0" seconds to cancel this function.

 No Answer Timer：When visitor presses the

door bell and no one answer the call, the

AMROAD P3 will ring for a time period. You

may select the time period- 15sec, 30sec,

45sec, or 60sec. Default is 15 seconds. The

setting should be based on your IP PBX.

 Incoming Allowed List Service：White List1

to White List5 fill in extension numbers(s)

in these fields to allow these resident’s

SIP-based devices to monitor through

AMROAD P3 by dialing AMROAD P3’s

extension number. All other SIP-based

devices can call in and monitor if all five

fields leave blank.

 ICMS：Engineering mode.

 Save：Click this button to save your setting.

SIP Settings

16

AMROAD P3

Entrance Settings

17

Page is loading ...

Amroad AMROAD P3 Technical Manual

Amroad AMROAD P3 Technical Manual

Related papers

Other documents