Swegon Slip-clamp and Euroflange Owner's manual

Swegon
Brand
Swegon
Model
Slip-clamp and Euroflange
Type
Owner's manual

Swegon Slip-clamp and Euroflange

These devices are designed to help you achieve optimal air tightness in your ventilation system.

  • The Slip-clamp is suitable for use with sound attenuators and ducts, while the Euroflange is designed for use with Euroflange frames.
  • Both devices come with sealing strips and gaskets to ensure a tight seal.
  • The Slip-clamp is easy to install by simply pressing the sealing strip into the rail and tapping the guide rail into place.
  • The Euroflange is installed by gluing the gasket to the inner edge of the flange and then tapping the guide rail into place.

Swegon Slip-clamp and Euroflange

These devices are designed to help you achieve optimal air tightness in your ventilation system.

  • The Slip-clamp is suitable for use with sound attenuators and ducts, while the Euroflange is designed for use with Euroflange frames.
  • Both devices come with sealing strips and gaskets to ensure a tight seal.
  • The Slip-clamp is easy to install by simply pressing the sealing strip into the rail and tapping the guide rail into place.
  • The Euroflange is installed by gluing the gasket to the inner edge of the flange and then tapping the guide rail into place.
Slip-clamp and Euroange
Installation 20230322
Art. 942428082
The document was originally written in Swedish
Checks
Before installing Slip-clamp and Euroflange, it is
important to check the following points to satisfy
the air tightness classes.
• Check that there is no damage to sound attenuators or
ducts, which could affect the air tightness class
• Check that there is no damage to joint profiles
• Check that there is no damage to the sealing strips
• Check that the sound attenuator is horizontal/aligned
with the connecting part, and that they are as close as
possible
• Check that the slip-clamp joint (slip-clamp mounting)
is correctly mounted on the opposite connection with
sealing compound and a sealing strip, according to
applicable regulations
• Check that the Euroflange frame (Euroflange mounting)
is correctly mounted on the opposite connection with
sealing compound and a sealing strip, according to
applicable regulations.
Swegon accepts no responsibility for any direct or indirect
damage caused by incorrect mounting.
Slip-clamp and Euroange
2Swegon reserves the right to make design changes. 22/03/2023
Slip-clamp
First read the Checks section and remedy if necessary before starting installation.
First install the sealing strip, making sure there is no play at the meeting ends (see Figure 1). Note: do not pull the strip,
rather simply press the strip down into the rail, do not join in the corners (at least 100 mm from a corner).
Push/carefully tap the guide rail (with a wooden/plastic mallet) (see Figure 2). Make sure that they meet in the corners to
achieve an optimal seal. Lock the guide rail in a suitable manner.
Figure2. Installing the guide rail
Figure1. Slip-clamp with gasket
>10 0 mm
3
22/03/2023 Swegon reserves the right to make design changes.
Slip-clamp and Euroange
Figure4. Installation of Euroflange
Euroflange
First read the Checks section and remedy if necessary before starting installation.
Glue the gasket along the inner edge of the flange (see Figure 3); in order to increase adhesion, it may be necessary to
wipe off the flange first with a suitable detergent. Do not join the gasket in the corners (at least 100 mm from corners).
Screw the corners together with suitable screws, which do not cover the guide rail installation. Push/carefully tap the
guide rail (with a wooden/plastic mallet) (see Figure 4). Lock the guide rail in a suitable manner.
If you experience any difficulties installing the guide rail, a profile clamp can be used instead.
Figure 3. Euroflange with gasket
>10 0 mm
  • Page 1 1
  • Page 2 2
  • Page 3 3

Swegon Slip-clamp and Euroflange Owner's manual

Swegon
Brand
Swegon
Model
Slip-clamp and Euroflange
Type
Owner's manual

Swegon Slip-clamp and Euroflange

These devices are designed to help you achieve optimal air tightness in your ventilation system.

  • The Slip-clamp is suitable for use with sound attenuators and ducts, while the Euroflange is designed for use with Euroflange frames.
  • Both devices come with sealing strips and gaskets to ensure a tight seal.
  • The Slip-clamp is easy to install by simply pressing the sealing strip into the rail and tapping the guide rail into place.
  • The Euroflange is installed by gluing the gasket to the inner edge of the flange and then tapping the guide rail into place.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents