Fakir Prestige 2002 CT Owner's manual

Bedienungsanleitung

Instructions for use

Mode d´emploi

Instrucciones de uso

Konvektor

Convector

Convecteur

Convectores

2002 CT

2002 CTF

Prestige

2002CTF-8606.QXD 13.06.2006 10:56 Seite 1

2

A

36 cm

min. 40 cm

min. 5 cm

Gerätebeschreibung

product description • Description de l’apareil • Descripsión del aparato

A

C

B

E

D

E

A Wandbefestigungshalter

Wall mounting holders • supports de fixation murale • soportes murales

B Betriebsartenschalter und Thermostat

Mode switch and thermostat • Sélecteur de mode et thermostat • Conmutador

de modos de servicio y termostato

C Luftaustrittsgitter

Air outlet grille • Grille de sortie d'air • Rejilla de salida de aire

D Gebläse-Luftaustrittsgitter

Blower air outlet grille • Grille de sortie d'air de soufflante • Rejilla de salida de

aire del soplador

E Standfuß

stand • Pied • Pata

2002CTF-8606.QXD 13.06.2006 10:56 Seite 2

Page is loading ...

8

Before using the appliance

• Please read the information below with care. This gives important guidance on the

use, safety and maintenance/care of the appliance. Keep this instruction booklet in a

safe place, and if appropriate, pass it on to the next owner.

• FAKIR appliances comply with the recognised technological standards and current

safety regulations.

• This appliance meets the requirements of EU guidelines 89/336/EU "Electromagnetic

compatibility" and 73/23/EU "Low voltage guideline". This is indicated by the CE mark

on the rating plate.

• FAKIR reserves the right to alter designs and specifications without notice.

General instructions

• Do not connect the appliance to the mains power socket if the voltage given on the

rating plate differs from the mains voltage.

• The power socket must be protected by a domestic 16 A automatic circuit-breaker.

• Do not use the appliance in case of any evidence of damage (cracks / fractures), if the

connecting lead is defective, or if internal damage is suspected (e.g. after being drop-

ped).

• Appliance surface can get heated up over 60°C.

• Please only use the appliance in vertical position.

• The appliance must not be fitted and operated into a vehicle.

• Appliance is not suitable for connection to fixed wiring systems.

• Heaters should be cleaned and inspected in a Fakir serviceshop before each heating

season.

• The power supply cord has to be replaced by an authorized Fakir After Sales Service

only.

• Repairs should be carried out only by an authorized Fakir service center (see guaran-

tee card for list of addresses). Incorrect repairs may expose the user to electrical dan-

ger.

• Fakir will not accept any liability for damage or injury if the appliance is used other than

for its intended purpose or is improperly operated or inexpertly repaired and maintai-

ned.

• The appliance does not need special maintenance or care.

Information for safety and notes on disposal

GB

2002CTF-8606.QXD 13.06.2006 10:56 Seite 8

9

Safety precautions

• After use, please disconnect appliance, pull out mains plug, let appliance cool down

and wind up cable. Please store appliance protected from dust.

• Do not let children use electrical appliances unsupervised.

• Caution: Never use the appliance in the bathroom, shower and washroom.

• Heater to be erected so that there is a clearance of 50 cm between the top grill and

other item of furniture or fitting. Always position the appliance so that it cannot ignite

items that can burn.

• Appliance must not be covered with towels, curtains or similar items because cover-

ing up might cause overheating. Nothing must hinder inflow of fresh air or outflow of

heated air.

• Do not pull out the plug from the power supply socket by pulling on the power supply

cord.

• Do not pull the power supply cord over sharp edges or allow it to become jammed.

• During use of the appliance the power supply cord must be unwound from the cord

holder.

• The power supply cord must not lie on the appliance when in use.

• Do not use damaged extension leads.

• Do not store the appliance in the open air or in the car or permit it to be exposed to

any other source of heat.

• Pull out the plug from the power supply socket before cleaning the appliance and use

only a dry or slightly moist cloth. Take care to prevent any live components (switch,

plug, heating element etc.) from coming into contact with water.

Disposal instructions

• Please dispose of the packaging materials and, eventually, the appliance itself in

accordance with the official regulations or guidelines which apply.

• If facilities are available in your locality for the recycling of packaging materials, plea-

se make use of these accordingly.

• When finally disposing of the appliance itself, please render it unserviceable before

taking it to the authorized place of disposal.

Information for safety and notes on disposal

2002CTF-8606.QXD 13.06.2006 10:56 Seite 9

10

The convector 2002 CT and 2002 CTFcan be used a standing or wall-mounted model.

Stand model:

Fit the two stands with the supplied screws to the bottom of the unit on the left and right.

Take care that the guide catch and the two guide lugs on the stand are inserted accura-

tely in the corresponding openings in the convector housing.

Wall-mounted model:

For mounting the wall holders select a place close (on the side) to a wall outlet – not in

the open or in damp rooms – and observe the minimum distance [F] to the wall, ceiling

and/or floor stated in the installation sketch (see page 3).

To install the wall holders hold these – according to the sketch on page 2 – at the inten-

ded place against the wall and transfer or mark the mounting holes with a pointed pencil.

Take care that the holders stand vertically and no electric cables or pipes can be drilled

though.

Fit the two wall holders with the supplied screws and wall plugs.

Remove the two stands (and keep them !), if you have previously used the unit as a stand

model and hook the convector in the wall holder until is audibly snaps into place.

Remove the convector: for this purpose pull the unit upwards out from the holders.

Plug the mains plug in the wall outlet. Turn the thermostat knob to the right (clockwise)

up to the stop and switch on with the operating mode switch:

Switch positions:

position [

−−

] = 750 watts heater

position [

==

] = 1250 watts heater

position [

−−

] + [=] = 2000 watts heater

position

±

= turbo blower ON

When the turbo blower is switched on, the room air is heated up quite quickly and uni-

formly.

Room thermostat

The heat intensity can be selected with a gliding movement by using the thermostat:

Position MIN. = lowest temperature / frost guard setting

Position MAX. = highest temperature

Turn the thermostat switch as far as possible in a clockwise direction. When the room rea-

ches the required temperature, then turn the thermostat in an anticlockwise direction, until

the appliance turns off. Should the room temperature reduce to below the required level

then the appliance will turn on again automatically.

Before use

Operation

2002CTF-8606.QXD 13.06.2006 10:56 Seite 10

11

Frost guard setting

In order to prevent the room temperature from falling below + 5°C (e.g. during a longer

absence), set the mode switch to position [

−−

] and the room thermostat to the frost guard

symbol MIN. The appliance switches on automatically at + 5°C and off again at about

+7°C. This prevents damage from frost.

Overheating cut out

If the unit is overheated because of inadequate air circulation, the built-in overheating cut

out switches the heater off automatically. The turbo blower continues to run if it was swit-

ched on previously and helps to cool the unit down. After the unit has cooled down suffi-

ciently, the overheating cut out switches the heater back on automatically. Disconnect

appliance and pull out mains plug. Let appliance cool down and wind up cable. Store

appliance protected from dust.

2002 CTF:

(fig. page 3)

1 Mains switch ON - OFF

2 Tiimer: setting sequence = 1h→ 2h →3h → . . . → 15 h → OFF → 1h . . .

2a The total operating time results from the sum of the settings indicated by LED lights

3 Temperature: every setting is increasing resp. reducing the desired temperature

4 Heating: setting sequence = ON→750 W→1250 W→2000 W→OFF→ON→ ...

4a The total heating results from the sum of the settings indicated by LED lights

5 Fan: ON - OFF

6 Switch over from ° C to ° F (Celsius - Fahrenheit)

6a Indication by LED light: °C / °F

7 Display: indication of the actual / desired temperature

8 I.R. receiver

Maintenance / Care

The appliance does not need special maintenance or care. When cleaning the applian-

ce, use only a dry of slightly moistened cloth. Take care to prevent any live components

(switch, plug, heating element, etc.) from coming into contact with water.

Faults

Should the appliance fail to operate satisfactorily (no heat emitted, unusual noises or

complete failure) have it checked and if necessary repaired by Fakir’s after-sales servi-

ce. This also applies if the appliance repeatedly cuts out in spite of being used correctly.

After use

Operation

2002CTF-8606.QXD 13.06.2006 10:56 Seite 11

Page is loading ...

Fakir Prestige 2002 CT Owner's manual

This manual is also suitable for

Fakir Prestige 2002 CT Owner's manual

in other languages

Related papers

Other documents