Masport Gasoline Edger - B&S Owner's manual

Brand: Masport

Model: Gasoline Edger - B&S

Category: Lawnmowers

Type: Owner's manual

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

www.masport.com

Petrol Edger / Kantensnijder op benzine /

Débroussailleuse à essence / Cortaorillas a gasolina.

IMPORTANT / BELANGRIJK / IMPORTANTE

Part N

: 550454

OWNER’S MANUAL.

ENG

Please read these instructions carefully before assembly.

Keep these and the engine instructions in a safe place for

future use.

This manual covers a range of different Masport Petrol Edgers.

Some features mentioned may not apply to your Petrol Edger.

GEBRUIKERSHANDLEIDING.

NLD

Lees deze voorschriften zorgvuldig alvorens de machine te

monteren. Bewaar deze voorschriften en die over de motor

op een veilige plaats om ze later te kunnen raadplegen.

Deze handleiding geldt voor een reeks verschillende Masport-

kantensnijders op benzine. Mogelijk zijn sommige punten niet van

toepassing op uw kantensnijder.

MANUEL D’UTILISATION.

FRA

Lire soigneusement ces instructions avant l’assemblage de

l’appareil. Garder ces instructions et celles du moteur dans

un endroit sûr pour pouvoir vous y référer ultérieurement.

Ce manuel couvre toute une gamme de débroussailleuses

à essence Masport. Les caractéristiques mentionnées ici ne

s’appliquent pas toujours à votre débroussailleuse.

MANUAL DEL PROPIETARIO.

ESP

Lea estas instrucciones detenidamente antes del montaje.

Guarde estas instrucciones y las del motor en un sitio

seguro para uso en el futuro.

Este manual cubre una gama de diferentes Cortaorillas a gasolina

de Masport. Algunas características mencionadas tal vez no

correspondan a su cortaorillas a gasolina.

PANTONE 648C

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

ESPAÑOL FRANÇAIS NEDERLANDS ENGLISH

Do not operate this machine before it has been

assembled correctly and you have read and

understood these instructions.

Do not allow children to operate this equipment.

These instructions are intended as a general guide

and do not supersede national or local codes in any

way. Contact local Authorities for clarity of laws

relating to operation of this appliance.

Contents

Symbols in this Owner’s Manual 3

Symbols used on the machine 3

Important Safety Instructions 3

Assembling the Edger 4

Preparing the Engine 4

Fuel 5

Starting the Engine 6

Stopping 6

After Use 6

Cut Depth Control 6

Blades 6

Engine Maintenance 7

Operating Position 8

Troubleshooting 8

Symbols in this Owner’s Manual

Threatened hazard or hazardous situation.

Not observing this instruction can lead to injuries or

cause damage to property.

Important information on proper handling.

Not observing this instruction can lead to faults in

the machine.

User information. This information helps you to use

all the functions correctly.

Symbols used on the Machine

Read and understand this Owner’s Manual before

operating the machine.

Direction of edger blade rotation

Always wear ear protection when using

the machine

Always wear eye protection when using

the machine

Keep bystanders at a safe distance

Thrown objects

Rotating cutting blade

Keep hands and feet clear

Remove Spark Plug

Keep bystanders clear. Danger of ﬂying objects.

Operator Presence Control Bail

Remove Spark Plug Wire

Noise Limit

Important Safety Instructions

The instructions presented in this manual are not all-inclusive: they

shall be provided with each machine and tailored

to the speciﬁc machine design.

1. Training

a) Read the instructions carefully. Be familiar with the controls and

the proper use of the equipment.

b) Never allow children or people unfamiliar with these instructions

to use the edger. Local regulations may restrict the age of the

operator.

c) Never edge while people, especially children, or pets are

nearby.

d) Keep in mind that the operator or user is responsible for

accidents or hazards occurring to other people or their

property.

Keep the instructions in a safe place for future use.

EIN

OFF

AUS

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

2. Preparation

a) While edging, always wear eye and ear protection, substantial

foot wear, and long trousers.

b) Thoroughly inspect the surface where the equipment is to be

used and remove all stones, sticks, wires, bones and other

foreign objects.

c) WARNING: Petrol is highly ﬂammable.

Take the following precautions:

1. Store fuel in containers speciﬁcally designed for this

purpose.

2. Refuel outdoors only and do not smoke while

refuelling.

3. Add fuel before starting the engine. Never remove the

cap of the fuel tank or add petrol while the engine is

running or when the engine is hot.

4. Avoid spillage: if petrol is spilled, do not attempt to

start the engine but move the machine away from

the area of spillage and avoid creating any source of

ignition until petrol vapors have dissipated.

5. Tighten all fuel tank and container caps securely.

d) Replace faulty silencers.

e) Before using, always visually inspect to see that the blade is

not worn or damaged. Replace worn or damaged blades to

preserve balance.

f) Use only manufacturer-recommended replacement parts and

accessories.

3. Operation

a) Do not operate the engine in a conﬁned space where

dangerous carbon monoxide fumes can collect. Breathing

exhaust fumes can be fatal.

b) Edge only in daylight or in good artiﬁcial light.

c) Always be sure of your footing on slopes.

d) Walk, never run.

e) Use extreme caution when reversing or pulling the edger

toward you.

f) Make sure the blade has stopped before crossing surfaces

other than grass and when transporting the edger to and from

the area to be edged.

g) Never operate the edger with defective, missing or incorrectly

ﬁtted guards.

h) Do not change the engine governor settings or overspeed the

engine.

i) Start the engine or switch on the motor carefully according to

instructions and with feet well away from the blade(s).

j) Do not tilt when starting the engine or switching on the motor,

unless the edger has to be tilted for starting. In this case, do

not tilt it more than absolutely necessary and lift only the part

which is away from the operator.

k) Do not start the engine when a bystander is standing in front of

the blade(s).

l) Do not put hands or feet near or under rotating parts.

m) Always switch off the electric motor and disconnect from main

or stop the fuel powered engine:

1. before clearing blockages;

2. before checking, cleaning or working on the blade(s);

3. after striking a foreign object: inspect the blade(s)

for damage and make repairs before restarting and

operating the edger;

4. if edger starts to vibrate abnormally (check

immediately).

n) Stop the engine:

1. whenever you leave the edger;

2. before refuelling.

o) Reduce the throttle setting during engine run-out and, if the

engine is provided with a shut-off valve, turn the fuel off at the

conclusion of edging.

4. Maintenance and storage

a) Keep all nuts, bolts and screws tight to be sure the equipment

is in safe working condition.

b) Never store the equipment with petrol in the tank inside a

building where fumes may reach an open ﬂame or spark.

c) Allow the engine to cool before storing in any enclosure.

d) To reduce the ﬁre hazard, keep the engine, silencer, battery

compartment, and petrol storage area free of grass, leaves or

excessive grease.

e) Replace worn or damaged parts.

f) If the fuel tank has to be drained, do this outdoors.

g) Do not attempt to repair the machine unless you are competent

to do so.

h) Use only manufacturer-recommended replacement parts and

accessories.

Assembling the Edger

Please refer to the following sections when preparing the edger for

its ﬁrst use.

• Fitting the handle

• Preparing the Engine

FITTING THE HANDLE

In some cases the handle may be completely detached from the

edger body although the upper handle may be connected by the

OPC Stop Ignition wires. Carefully remove the edger and handles

from the box together to avoid damaging the OPC Stop Ignition

wires.

Fit the two long bolts through the holes in the lower handle from the

inside with the round heads snug against the tube. Fit the holes in

the upper handle over the two long bolts. Attach the plastic knob to

the outside of the lower handle bolt as shown below and tighten by

hand until the upper handle is locked in position.

Preparing the Engine

PLEASE READ AND UNDERSTAND THE ENGINE

MANUFACTURERS ENGINE OWNER’S MANUAL PRIOR TO

OPERATING THE EDGER.

DO NOT START your four stroke engine

before making sure that it has been filled

with the right amount of the correct grade

of oil. See engine instruction book for

details.

CAUTION

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

ESPAÑOL FRANÇAIS NEDERLANDS ENGLISH

OIL

Four stroke (cycle) engines are shipped without oil. Place the edger

on a level position, unscrew the ‘OIL FILL’ cap and slowly pour oil

into the sump. Fill to the full mark on the dipstick. The capacity is

approximately 600 ml. Use SAE 30 engine oil. After checking the

oil level, and before running the engine, screw the dipstick ﬁrmly in

place.

Checking the oil level if the engine is not ﬁtted with a dip stick.

CHANGING THE ENGINE OIL

FOUR STROKE ENGINES should be checked for oil level every 8

hours running (or daily), and the oil should be drained and replaced

after every 50 hours of use.

Fuel

PETROL VAPOUR IS HIGHLY FLAMMABLE

AND EXPLOSIVE. HANDLE WITH EXTREME

CARE. STORE IN AN APPROVED CONTAIN-

ER. DO NOT FILL TANK WHEN ENGINE IS

RUNNING OR IS STILL HOT. DO NOT ALLOW

OPEN FLAME, MATCHES OR SMOKING

NEARBY. FILL TANK OUTDOORS IN A WELL

VENTILATED AREA. WIPE AWAY ANY SPILLS

AND MOVE THE MOWER AWAY FROM ANY

PETROL FUMES BEFORE STARTING

ENGINE.

WARNING

If a blue plug is fitted beneath the petrol filler cap

it must be discarded. It is for transportation pur-

poses only.

If a blue plug is fitted beneath the petrol filler cap

it must be discarded. It is for transportation pur-

poses only.

CAUTION

For two stroke engines fuel ratio, refer to engine instruction book.

When ﬁlling the fuel tank, always leave an air space of about 5mm

to allow for expansion of the fuel.

ENGINE

Regular attention to a few simple items will ensure long and trouble-

free service from your mower. Carry out the regular maintenance

described in the engine manual, and check the engine mounting

bolts regularly to be sure they are tight.

NOTE: THE ENGINE IS WARRANTED BY THE ENGINE

MANUFACTURER AND NOT MASPORT. YOUR SPECIALIST

MASPORT SERVICE DEALER CAN ASSIST WITH ENGINE

RELATED WARRANTY MATTERS.

Before making any adjustments to your edger

make sure that the engine is turned off and that

the blade has STOPPED ROTATING. Always

disconnect the spark plug wire and make sure it

cannot accidentally contact the spark plug before

touching anything under the edger housing.

WARNING

Starting the Engine

For more detail description refer to the Engine Owner’s Manual

provided.

1. Make sure the isolator switch on the left hand side of the

engine is turned on.

2. Ensure the blade is clear of the ground. Check the height

adjuster is at the highest setting.

3. Turn the petrol tap on.

OPC Bail

NOTE: This edger is ﬁtted with an Operator Presence control

(OPC) bail at the top of the handle. This must be squeezed against

the handlebar before starting the engine. The engine will stop

immediately when the bail is released.

Some controls have symbols instead of words. On these,

means CHOKE,

means FAST,

means SLOW,

means STOP.

If your engine control does not have the word CHOKE or the choke

symbol

you have a Pulsa Prime engine. (See RUNNING THE

ENGINE, MANUAL START MODELS).

Throttle

Isolator

switch

Petrol

tap

Choke

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

MANUAL START MODELS. If the engine has not been running

recently, or you have cold starting problems, set the engine

control to the CHOKE position. Refer engine owner’s manual.

Grasp the starter grip, pull slowly until a resistance is felt and then

pull forcefully to prevent kick-back. Repeat until the engine starts.

Do not pull the cord with a jerk or release it until fully rewound.—

When the engine starts and has warmed up for a short time,

move the control to the desired speed. Should the engine not start

due to ‘ﬂooding’, move the control to SLOW and pull the starter six

times to clear the ﬂooding.

HINTS FOR EASY STARTING

1. Stand edger on ﬁrm ground.

2. Set the height setting to the highest setting.

3. Start a warm engine with the control in the SLOW

position.

4. Keep the edger clean underneath.

HARD STARTING CHECK LIST

Look for these faults:-

FUEL 1. Insufﬁcient fuel in tank.

2. Fuel tap shut off.

3. Stale fuel.

4. Water or dirt in fuel.

5. Blocked air vent in fuel tank cap.

IGNITION 1. Loose spark plug wire.

2. Dirty spark plug electrodes.

3. Incorrect spark plug gap.

4. Incorrect spark plug type.

OTHER 1. Choked air ﬁlter (Dirt or oil).

2. Engine control cable mis-adjusted.

3. Cutting blade obstructed.

Stopping

Move the engine control to stop.

OPC Bail

OPERATOR PRESENCE CONTROL (OPC) BAIL

This is a safety feature which stops the engine quickly if the

operator releases their grip on the handle. To start the engine, you

must move the bail back and hold it against the handlebar.

If the machine run/brake mechanism is not

adjusted correctly or is damaged the blade

could continue to rotate after the OPC arm

is released. In this situation, do not use the

edger. Contact your local servicing

specialist.

WARNING

After Use

CLEANING

DO NOT HOSE THE ENGINE, as water can

damage the air cleaner and the ignition system.

REFER TO ENGINE INSTRUCTION BOOK

MAINTENANCE SECTION BEFORE TILTING

EDGER. STORE YOUR EDGER ON ITS

WHEELS, not its side.

CAUTION

Cut Depth Control

The single point cut height control adjusts the front wheels only.

To operate, steady the edger by grasping the handle with one

hand, pull the lever outwards from the slots with the other hand

and move it to the desired setting.

Blades

DAMAGED BLADES ARE MAJOR HAZARDS.

Check the blade mounting shaft and nut at frequent intervals for

proper tightness.

Check the blade condition frequently, particularly if the edger has

hit a foreign object or is vibrating. Your Authorised Dealer will be

happy to sharpen or replace blades as necessary, or if you prefer,

supply the parts you will need to do the job yourself.

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

ESPAÑOL FRANÇAIS NEDERLANDS ENGLISH

CAUTION

ALWAYS USE GENUINE ORIGINAL EQUIPMENT

PARTS TO ENSURE SAFETY AND

PROPER PERFORMANCE. Substitute parts can

be disappointing and dangerous.

BLADE SERVICING INSTRUCTIONS.

1. Remove the spark plug lead and position it to prevent

accidental contact with the spark plug.

2. Place edger on work bench or table.

3. Remove guard.

4. Using 2 x 24mm spanners remove the outer M16 nut.

5. Remove the lock washer and ﬂat washer.

6. Remove blade and replace with a new one. Assemble in the

reverse order.

7. Torque blade nut to 80 Nm

Engine Maintenance

Consult the engine booklet for the maker’s instructions.

DRAINING THE OIL.

Remove the drain plug which is situated at the rear base of the

engine. Collect the old oil in a suitable tray such as a two litre ice

cream container.

IGNITION.

Your engine has a breaker-less solid state ignition system which

requires no maintenance other than occasional attention to the

spark plug. We recommend cleaning and re-gapping

every 50 hours with replacement every 100 hours (see engine

instruction booklet).

CAUTION

DO NOT SANDBLAST PLUGS as abra-

sive grains can enter the engine and

cause serious damage. USE ONLY THE

EXACT TYPE OF REPLACEMENT PLUG

specified in the engine instruction booklet.

AIR CLEANER.

A clean ﬁlter cartridge, correctly ﬁtted, is ESSENTIAL for long

engine life. Service the ﬁlter every 25 hours running (more often

under adverse conditions) according to the instructions in the

engine booklet.

MUFFLER.

A rusted or damaged mufﬂer can permit increased exhaust noise.

Check the mufﬂer condition periodically and replace it only with a

genuine original equipment part.

BELT ADJUSTMENT.

1. Remove the spark plug lead and position it to prevent

accidental contact with spark plug.

2. Remove belt cover.

3. Using a 13mm socket, slacken the four bolts holding the

adjusting base.

4. Slide the adjusting base to tighten the belt and re-clamp the

four bolts.

5. Replace the belt cover.

2. Belt cover nut

Slide adjusting

base to tighten

2. Adjusting

base bolts

Operating Position

Please ensure the operator is positioned properly while starting,

adjusting, operating, and stopping the product.

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

Troubleshooting

PROBLEM POSSIBLE CAUSE(S) CORRECTIVE ACTION

Not Cutting Belt is slipping Tighten belt

Engine not running at full speed Move the throttle to fast

Vibrating Worn or damaged blade Replace blade

Technical Data

Model: Edger Petrol 950915

Engine Type: GC160 160cm

Engine Power: 2.38kW

Rated no-load speed: 2400/min

Petrol tank capacity: 1.8L

Oil tank capacity: 610mL

Cutting Depth MAX: 50mm

Adjustable Cutting Depth: +13 - -50mm

Cutting blade part number: 550442 Edger Blade

Weight: 30kg

Sound pressure level L

at the operator position: 93dB(A)

Measured sound power level L

: 97dB(A)

Guaranteed sound power level L

(2000/14/EC): 98dB(A)

Technical Data

Model: Edger Petrol 950913

Engine Type: 3.5 I/C 127cm

Engine Power: 2.39kW

Rated no-load speed: 2800/min

Petrol tank capacity: 950mL

Oil tank capacity: 600mL

Cutting Depth MAX: 50mm

Adjustable Cutting Depth: +18 - -50mm

Cutting blade part number: 550442 Edger Blade

Weight: 30kg

Sound pressure level L

at the operator position: 94dB(A)

Measured sound power level L

: 98dB(A)

Guaranteed sound power level L

(2000/14/EC): 98dB(A)

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

ESPAÑOL FRANÇAIS NEDERLANDS ENGLISH

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

Page is loading ...

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

ESPAÑOL FRANÇAIS NEDERLANDS ENGLISH

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

Page is loading ...

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

ESPAÑOL FRANÇAIS NEDERLANDS ENGLISH

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

Page is loading ...

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

ESPAÑOL FRANÇAIS NEDERLANDS ENGLISH

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

ESPAÑOL FRANÇAIS NEDERLANDS ENGLISH

550454 - Masport Petrol Edger Owner’s Manual - July ‘14

Masport Gasoline Edger - B&S Owner's manual

Brand: Masport

Model: Gasoline Edger - B&S

Category: Lawnmowers

Type: Owner's manual

Download PDF

report

in other languages

français: Masport Gasoline Edger - B&S Le manuel du propriétaire
español: Masport Gasoline Edger - B&S El manual del propietario
Nederlands: Masport Gasoline Edger - B&S de handleiding

Masport Gasoline Edger - B&S Owner's manual

Masport Gasoline Edger - B&S Owner's manual

in other languages

Related papers

Other documents