Makita MT605 User manual

Brand: Makita

Model: MT605

Category: Power tools

Type: User manual

This manual is also suitable for

MT606
MT607

Drill Instruction manual

Bor Petunjuk penggunaan

Máy khoan Tài liu hng dn



MT605

MT606

MT607

1 011878 2 011925

3 011877 4 011880

ENGLISH

Explanation of general view

SPECIFICATIONS

•Due to our continuing programme of research and development, the specifications herein are subject to change without

notice.

• Specifications may differ from country to country.

•Weight according to EPTA-Procedure 01/2003

END201-5

Symbols

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

.... Read instruction manual.

.............. DOUBLE INSULATION

ENE032-1

Intended use

The tool is intended for drilling in wood, metal and plastic.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

GEA005-3

General Power Tool Safety

Warnings

WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause you

to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of

electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

10. Use of power supply via a RCD with a rated

residual current of 30mA or less is always

recommended.

1. Switch trigger

2. Lock button

3. Reversing switch lever

4. Chuck key

5. Sleeve

6. Ring

Model MT605 MT606 MT607

Capacities

Steel 10 mm 10 mm 10 mm

Wood 25 mm 25 mm 25 mm

No load speed (min

-1

) 3,000 0 - 3,000 0 - 3,000

Overall length 229 mm 229 mm 234 mm

Net weight 1.3 kg 1.3 kg 1.3 kg

Safety class /II

Personal safety

11. Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personal injury.

12. Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

13. Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch

on invites accidents.

14. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personal injury.

15. Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpected situations.

16. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

17. If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-related hazards.

Power tool use and care

18. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

19. Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

20. Disconnect the plug from the power source and/or

the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

21. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

22. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

23. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

24. Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

Service

25. Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

is maintained.

26. Follow instruction for lubricating and changing

accessories.

27. Keep handles dry, clean and free from oil and

grease.

GEB001-6

DRILL SAFETY WARNINGS

1. Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

2. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. Cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

3. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

4. Hold the tool firmly.

5. Keep hands away from rotating parts.

6. Do not leave the tool running. Operate the tool

only when hand-held.

7. Do not touch the drill bit or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

8. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

CAUTION:

•Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

•Before plugging in the tool, always check to see the

switch trigger actuates properly and returns to the

“OFF” position when released.

For MT605

To start the tool, simply pull the switch trigger. Release the

switch trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

For MT606, MT607

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock button.

To stop the tool from the locked position, pull the switch

trigger fully, then release it.

Reversing switch action

For MT606, MT607 (Fig. 2)

This tool has a reversing switch to change the direction of

rotation. Move the reversing switch lever to the  position

(A side) for clockwise rotation or the  position (B side)

for counterclockwise rotation.

CAUTION:

•Always check the direction of rotation before operation.

•Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Installing or removing drill bit

CAUTION:

• Always be sure that the tool is switched off and

unplugged before installing or removing the bit.

For MT605, MT606 (Fig. 3)

To install the bit, place it in the chuck as far as it will go.

Tighten the chuck by hand. Place the chuck key in each of

the three holes and tighten clockwise. Be sure to tighten

all three chuck holes evenly.

To remove the bit, turn the chuck key counterclockwise in

just one hole, then loosen the chuck by hand.

For MT607 (Fig. 4)

Hold the ring and turn the sleeve counterclockwise to

open the chuck jaws. Place the bit in the chuck as far as it

will go. Hold the ring firmly and turn the sleeve clockwise

to tighten the chuck.

To remove the bit, hold the ring and turn the sleeve

counterclockwise.

OPERATION

Holding the tool

Hold the tool only by the handle when performing an

operation.

Drilling operation

Drilling in wood

When drilling in wood, the best results are obtained with

wood drills equipped with a guide screw. The guide screw

makes drilling easier by pulling the bit into the workpiece.

Drilling in metal

To prevent the bit from slipping when starting a hole, make

an indentation with a center-punch and hammer at the

point to be drilled. Place the point of the bit in the

indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be drilled dry.

CAUTION:

•Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool

performance and shorten the service life of the tool.

•There is a tremendous force exerted on the tool/bit at

the time of hole break through. Hold the tool firmly and

exert care when the bit begins to break through the

workpiece.

•Always secure small workpieces in a vise or similar

hold-down device.

MAINTENANCE

CAUTION:

•Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

•Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

BAHASA INDONESIA

Penjelasan tampilan keseluruhan

SPESIFIKASI

•Karena kesinambungan program penelitian dan pengembangan kami, spesifikasi yang disebutkan di sini dapat

berubah tanpa pemberitahuan.

•Spesifikasi dapat berbeda dari satu negara ke negara lainnya.

•Berat menurut Prosedur EPTA 01/2003

END201-5

Simbol

Berikut ini adalah simbol-simbol yang digunakan pada

peralatan ini.

Pastikan Anda mengerti makna masing-masing simbol

sebelum menggunakan alat.

..... Baca petunjuk penggunaan.

.............. ISOLASI GANDA

ENE032-1

Penggunaan

Mesin ini digunakan untuk membor kayu, logam dan

plastik.

ENF002-2

Pasokan daya

Mesin harus terhubung dengan pasokan daya listrik yang

bervoltase sama dengan yang tertera pada pelat nama,

dan hanya dapat dijalankan dengan listrik AC fase

tunggal. Mesin diisolasi ganda dan oleh sebab itu dapat

dihubungkan dengan soket tanpa arde.

GEA005-3

Peringatan Keselamatan Umum

Mesin Listrik

PERINGATAN! Bacalah semua peringatan

keselamatan dan semua petunjuk. Kelalaian mematuhi

peringatan dan petunjuk dapat menyebabkan sengatan

listrik, kebakaran dan/atau cedera serius.

Simpanlah semua peringatan dan

petunjuk untuk acuan di masa

depan.

Istilah “mesin listrik” dalam semua peringatan mengacu

pada mesin listrik yang dijalankan dengan sumber listrik

jala-jala (berkabel) atau baterai (tanpa kabel).

Keselamatan tempat kerja

1. Jaga tempat kerja selalu bersih dan

berpenerangan cukup. Tempat kerja yang

berantakan dan gelap mengundang kecelakaan.

2. Jangan gunakan mesin listrik dalam lingkungan

yang mudah meledak, misalnya jika ada cairan,

gas, atau debu yang mudah menyala. Mesin listrik

menimbulkan bunga api yang dapat menyalakan debu

atau uap tersebut.

3. Jauhkan anak-anak dan orang lain saat

menggunakan mesin listrik. Bila perhatian terpecah,

anda dapat kehilangan kendali.

Keamanan kelistrikan

4. Steker mesin listrik harus cocok dengan

stopkontak. Jangan sekali-kali mengubah steker

dengan cara apa pun. Jangan menggunakan

steker adaptor dengan mesin listrik berarde

(dibumikan). Steker yang tidak diubah dan

stopkontak yang cocok akan mengurangi risiko

sengatan listrik.

5. Hindari sentuhan tubuh dengan permukaan

berarde atau yang dibumikan seperti pipa,

radiator, kompor, dan kulkas. Risiko sengatan listrik

bertambah jika tubuh Anda terbumikan atau terarde.

6. Jangan membiarkan mesin listrik kehujanan atau

kebasahan. Air yang masuk ke dalam mesin listrik

akan meningkatkan risiko sengatan listrik.

1. Saklar pemicu

2. Tombol kunci

3. Tuas saklar pembalik arah

4. Kunci cekam

5. Selongsong

6. Cincin

Model MT605 MT606 MT607

Kapasitas

Baja 10 mm 10 mm 10 mm

Kayu 25 mm 25 mm 25 mm

Kecepatan tanpa beban (min

-1

) 3.000 0 - 3.000 0 - 3.000

Panjang keseluruhan 229 mm 229 mm 234 mm

Berat bersih 1,3 kg 1,3 kg 1,3 kg

Kelas keamanan /II

7. Jangan menyalahgunakan kabel. Jangan sekali-

kali menggunakan kabel untuk membawa,

menarik, atau mencabut mesin listrik dari

stopkontak. Jauhkan kabel dari panas, minyak,

tepian tajam, atau bagian yang bergerak. Kabel

yang rusak atau kusut memperbesar risiko sengatan

listrik.

8. Bila menggunakan mesin listrik di luar ruangan,

gunakan kabel ekstensi yang sesuai untuk

penggunaan di luar ruangan. Penggunaan kabel

yang sesuai untuk penggunaan luar ruangan

mengurangi risiko sengatan listrik.

9. Jika mengoperasikan mesin listrik di lokasi

lembap tidak terhindarkan, gunakan pasokan daya

yang dilindungi peranti imbasan arus (residual

current device - RCD). Penggunaan RCD

mengurangi risiko sengatan listrik.

10. Penggunaan pasokan daya melalui RCD dengan

kapasitas arus sisa 30 mA atau kurang selalu

dianjurkan.

Keselamatan diri

11. Jaga kewaspadaan, perhatikan pekerjaan Anda

dan gunakan akal sehat bila menggunakan mesin

listrik. Jangan menggunakan mesin listrik saat

Anda lelah atau di bawah pengaruh obat bius,

alkohol, atau obat. Sekejap saja lalai saat

menggunakan mesin listrik dapat menyebabkan

cedera diri yang serius.

12. Gunakan alat pelindung diri. Selalu gunakan

pelindung mata. Peralatan pelindung seperti masker

debu, sepatu pengaman anti-selip, helm pengaman,

atau pelindung telinga yang digunakan untuk kondisi

yang sesuai akan mengurangi risiko cedera diri.

13. Cegah penyalaan yang tidak disengaja. Pastikan

bahwa sakelar berada dalam posisi mati (off)

sebelum menghubungkan mesin ke sumber daya

dan/atau baterai, atau mengangkat atau

membawanya. Membawa mesin listrik dengan jari

Anda pada sakelarnya atau mengalirkan listrik pada

mesin listrik yang sakelarnya hidup (on) akan

mengundang kecelakaan.

14. Lepaskan kunci-kunci penyetel sebelum

menghidupkan mesin listrik. Kunci-kunci yang

masih terpasang pada bagian mesin listrik yang

berputar dapat menyebabkan cedera.

15. Jangan meraih terlalu jauh. Jagalah pijakan dan

keseimbangan sepanjang waktu. Hal ini

memungkinkan kendali yang lebih baik atas mesin

listrik dalam situasi yang tidak diharapkan.

16. Kenakan pakaian dengan baik. Jangan memakai

pakaian yang kedodoran atau perhiasan. Jaga

jarak antara rambut, pakaian, dan sarung tangan

Anda dengan bagian mesin yang bergerak.

Pakaian kedodoran, perhiasan, atau rambut panjang

dapat tersangkut pada bagian yang bergerak.

17. Jika tersedia fasilitas untuk menghisap dan

mengumpulkan debu, pastikan fasilitas tersebut

terhubung listrik dan digunakan dengan baik.

Penggunaan pembersih debu dapat mengurangi

bahaya yang terkait dengan debu.

Penggunaan dan pemeliharaan mesin listrik

18. Jangan memaksa mesin listrik. Gunakan mesin

listrik yang tepat untuk keperluan Anda. Mesin

listrik yang tepat akan menuntaskan pekerjaan

dengan lebih baik dan aman pada kecepatan sesuai

rancangannya.

19. Jangan gunakan mesin listrik jika sakelar tidak

dapat menyalakan dan mematikannya. Mesin listrik

yang tidak dapat dikendalikan dengan sakelarnya

adalah berbahaya dan harus diperbaiki.

20. Cabut steker dari sumber listrik dan/atau baterai

dari mesin listrik sebelum melakukan penyetelan,

penggantian aksesori, atau menyimpan mesin

listrik. Langkah keselamatan preventif tersebut

mengurangi risiko hidupnya mesin secara tak

sengaja.

21. Simpan mesin listrik jauh dari jangkauan anak-

anak dan jangan biarkan orang yang tidak paham

mengenai mesin listrik tersebut atau petunjuk ini

menggunakan mesin listrik. Mesin listrik sangat

berbahaya di tangan pengguna yang tak terlatih.

22. Rawatlah mesin listrik. Periksa apakah ada bagian

bergerak yang tidak lurus atau macet, bagian yang

pecah dan kondisi lain yang dapat mempengaruhi

penggunaan mesin listrik. Jika rusak, perbaiki

dahulu mesin listrik sebelum digunakan. Banyak

kecelakaan disebabkan oleh kurangnya pemeliharaan

mesin listrik.

23. Jaga agar mesin pemotong tetap tajam dan bersih.

Mesin pemotong yang terawat baik dengan mata

pemotong yang tajam tidak mudah macet dan lebih

mudah dikendalikan.

24. Gunakan mesin listrik, aksesori, dan mata mesin,

dll. sesuai dengan petunjuk ini, dengan

memperhitungkan kondisi kerja dan jenis

pekerjaan yang dilakukan. Penggunaan mesin listrik

untuk penggunaan yang lain dari peruntukan dapat

menimbulkan situasi berbahaya.

Servis

25. Berikan mesin listrik untuk diperbaiki hanya

kepada oleh teknisi yang berkualifikasi dengan

menggunakan hanya suku cadang pengganti yang

serupa.

Hal ini akan menjamin terjaganya keamanan

mesin listrik.

26. Patuhi petunjuk pelumasan dan penggantian

aksesori.

27. Jagalah agar gagang kering, bersih, dan bebas

dari minyak dan gemuk.

GEB001-6

PERINGATAN KESELAMATAN

BOR

1. Gunakan gagang tambahan, jika disertakan

bersama mesin ini. Kehilangan kendali dapat

menyebabkan cedera.

2. Pegang mesin listrik pada permukaan genggam

yang terisolasi saat melakukan pekerjaan bila

mesin pemotong mungkin bersentuhan dengan

kawat tersembunyi atau kabelnya sendiri. Aksesori

pemotong yang menyentuh kawat “hidup” dapat

menyebabkan bagian logam pada mesin teraliri arus

listrik dan menyengat pengguna.

3. Selalu pastikan Anda berdiri di atas alas yang

kuat.

Pastikan tidak ada orang di bawahnya bila Anda

menggunakan mesin di tempat tinggi.

4. Pegang mesin kuat-kuat.

5. Jauhkan tangan dari bagian yang berputar.

6. Jangan tinggalkan mesin dalam keadaan hidup.

Jalankan mesin hanya ketika digenggam tangan.

7. Jangan menyentuh mata bor atau benda kerja

segera setelah pengoperasian; suhunya mungkin

masih sangat panas dan dapat membakar kulit

Anda.

8. Bahan tertentu mengandung zat kimia yang

mungkin beracun. Hindari menghirup debu dan

persentuhan dengan kulit. Ikuti data keselamatan

bahan dari pemasok.

SIMPAN PETUNJUK INI.

PERINGATAN:

JANGAN biarkan kenyamanan atau terbiasanya Anda

dengan produk (karena penggunaan berulang)

menggantikan kepatuhan yang ketat terhadap aturan

keselamatan untuk produk yang terkait.

PENYALAHGUNAAN atau kelalaian mematuhi kaidah

keselamatan yang tertera dalam petunjuk ini dapat

menyebabkan cedera badan serius.

DESKRIPSI FUNGSI

PERHATIAN:

•Pastikan bahwa mesin dalam keadaan mati dan steker

tercabut sebelum menyetel atau memeriksa kerja

mesin.

Kerja saklar (Gb. 1)

PERHATIAN:

•Sebelum memasukkan steker ke stop kontak, pastikan

bahwa picu saklar berfungsi dengan baik dan kembali

ke posisi “OFF” ketika dilepas.

Untuk MT605

Untuk menjalankan mesin, cukup tarik picu saklarnya.

Lepaskan picu saklar untuk berhenti.

Untuk penggunaan terus menerus, tarik picu saklar lalu

tekan tombol kunci.

Untuk membebaskan posisi terkunci, tarik picu saklar

sampai penuh, lalu lepaskan.

Untuk MT606, MT607

Untuk menjalankan mesin, cukup tarik picu saklarnya.

Kecepatan mesin akan meningkat dengan menambah

tekanan pada picu saklar. Lepaskan picu saklar untuk

berhenti.

Untuk penggunaan terus menerus, tarik picu saklar lalu

tekan tombol kunci.

Untuk membebaskan posisi terkunci, tarik picu saklar

sampai penuh, lalu lepaskan.

Kerja saklar pembalik arah

Untuk MT606, MT607 (Gb. 2)

Mesin ini memiliki saklar pembalik arah untuk mengubah

arah putaran. Gerakkan tuas saklar pembalik arah ke

posisi  (sisi A) untuk putaran searah jarum jam atau

posisi  (sisi B) untuk putaran berlawanan arah jarum

jam.

PERHATIAN:

•Selalu periksa arah putaran sebelum penggunaan.

•Gunakan saklar pembalik arah hanya setelah mesin

berhenti penuh. Mengubah arah putaran sebelum

mesin berhenti dapat merusak mesin.

PERAKITAN

PERHATIAN:

•Pastikan bahwa mesin dalam keadaan mati dan steker

tercabut sebelum melakukan pekerjaan apapun pada

mesin.

Memasang atau melepas mata bor

PERHATIAN:

•Pastikan mesin dalam keadaan mati dan steker telah

dicabut, sebelum memasang atau melepas mata bor.

Untuk MT605, MT606 (Gb. 3)

Untuk memasang mata bor, masukkan mata bor ke dalam

cekam sedalam mungkin. Kencangkan cekam dengan

tangan. Masukkan kunci cuk ke dalam tiga lubang yang

ada dan kencangkan searah jarum jam. Pastikan ketiga

lubang cekam dikencangkan secara seragam.

Untuk melepas mata bor, putar kunci cekam berlawanan

arah jarum jam pada satu lubang saja, lalu bebaskan

mata bor dengan tangan.

Untuk MT607 (Gb. 4)

Tah an cinc in dan pu ta r s elongsong berlawanan arah

jarum jam untuk membuka rahang cekam. Masukkan

mata bor ke dalam cekam sejauh mungkin. Pegang cincin

dengan kuat dan putar selongsong searah jarum jam

untuk mengencangkan cekam.

Untuk melepas mata bor, pegang cincin dan putar

selongsong berlawanan arah jarum jam.

PENGGUNAAN

Memegang mesin

Pegang mesin hanya pada pegangannya saat melakukan

pekerjaan.

Pekerjaan pengeboran

Mengebor kayu

Bila mengebor kayu, hasil terbaik didapat dengan mata

bor kayu yang dilengkapi sekrup pemandu. Sekrup

pemandu mempermudah pengeboran dengan menarik

mata bor ke dalam benda kerja.

Mengebor logam

Untuk mencegah mata bor selip ketika mulai membuat

lubang, buatlah takik dengan penitik lalu palu pada titik

yang akan dilubangi. Letakkan ujung mata bor pada takik

dan mulailah membor.

Gunakan cairan pendingin saat mengebor logam.

Pengecualian untuk besi dan kuningan yang harus dibor

kering.

PERHATIAN:

•Menekan mesin secara berlebihan tidak akan

mempercepat pengeboran. Bahkan, tekanan yang

berlebihan hanya akan merusak mata bor Anda,

mengurangi kinerja mesin dan memperpendek usia

mesin.

•Akan timbul gaya yang sangat kuat pada mesin/mata

bor saat menembus lubang. Pegang mesin dengan

kuat dan berhati-hatilah saat mata bor menembus

benda kerja.

• Tahan benda kerja berukuran kecil dengan penjepit

atau alat penahan lain.

PERAWATAN

PERHATIAN:

•Pastikan bahwa mesin dalam keadaan mati dan steker

tercabut sebelum melakukan pekerjaan apapun pada

mesin.

•Jangan sekali-kali menggunakan bensin, tiner, alkohol,

atau bahan sejenisnya. Penggunaan bahan demikian

dapat menyebabkan perubahan warna, perubahan

bentuk atau timbulnya retakan.

Untuk menjaga KEAMANAN dan KEANDALAN mesin,

perbaikan, perawatan atau penyetelan lain harus

dilakukan oleh Pusat Layanan Resmi Makita; selalu

gunakan suku cadang pengganti buatan Makita.

TING VIT

Gii thích v hình v tng th

THÔNG S K THUT

•Do chng trình nghiên cu và phát trin liên tc ca chúng tôi nên các thông s k thut trong ây có th thay i mà

không cn thông báo trc.

•Các thông s k thut có th thay i tùy theo tng quc gia.

•Trng lng tùy theo Quy trình EPTA tháng 01/2003

END201-5

Ký hiu

Phn di ây cho bit các ký hiu c dùng cho thit b.

m bo rng bn hiu rõ ý ngha ca các ký hiu này

trc khi s dng.

..... c tài liu hng dn.

.............. CÁCH IN KÉP

ENE032-1

Mc ích s dng

Dng c này dùng  khoan g, kim loi và nha.

ENF002-2

Ngun cp in

Dng c này ch c ni vi ngun cp in có in áp

ging nh ã ch ra trên bin tên và ch có th c vn

hành trên ngun in AC mt pha. Chúng c cách in

hai lp và do ó cng có th c s dng vi các  cm

in không có dây tip t.

GEA005-3

Cnh báo An toàn Chung dành

cho Dng c Máy

CNH BÁO! c tt c các cnh báo an toàn và

hng dn. Vic không tuân theo các cnh báo và

hng dn có th dn n in git, ho hon và/hoc

thng tích nghiêm trng.

Lu gi tt c cnh báo và hng

dn  tham kho sau này.

Thut ng “dng c máy” trong các cnh báo  cp n

dng c máy (có dây) c vn hành bng ngun in

chính hoc dng c máy (không dây) c vn hành

bng pin ca bn.

An toàn ti ni làm vic

1. Gi ni làm vic sch s và có  ánh sáng. Ni

làm vic ba bn hoc ti thng d gây ra tai nn.

2. Không vn hành dng c máy trong môi tr

ng

cháy n, ví d nh môi trng có s hin din

ca các cht lng, khí hoc bi d cháy. Các dng

c máy to tia la in có th làm bi hoc khí bc

cháy.

3. Gi tr em và ngi ngoài tránh xa ni làm vic

khi ang vn hành dng c máy. S xao lãng có th

khin bn mt kh nng kim soát.

An toàn v in

4. Phích c

m ca dng c máy phi khp vi  cm.

Không bao gi c sa i phích cm theo bt

k cách nào. Không s dng bt k phích chuyn

i nào vi các dng c máy c ni t (tip

t). Các phích cm còn nguyên vn và  cm phù

hp s gim nguy c in git.

5. Tránh  c th tip xúc vi các b m

t ni t

hoc tip t nh ng ng, b tn nhit, bp ga

và t lnh. Nguy c b in git s tng lên nu c

th bn c ni t hoc tip t.

6. Không  dng c máy tip xúc vi ma hoc

trong iu kin m t. Nc lt vào dng c

 máy

s làm tng nguy c in git.

7. Không lm dng dây. Không bao gi s dng dây

 mang, kéo hoc tháo phích cm dng c máy.

Gi dây tránh xa ngun nhit, du, các mép sc

hoc các b phn chuyn ng. Dây b hng hoc

b ri s làm tng nguy c in git.

8. Khi vn hành dng c máy ngoài tri, hãy s

dng dây kéo dài phù hp cho vi

c s dng ngoài

tri. Vic dùng dây phù hp cho vic s dng ngoài

tri s gim nguy c in git.

9. Nu bt buc phi vn hành dng c máy  ni

m t, hãy s dng ngun cp in c bo v

bng thit b ngt dòng in rò (RCD). Vic s

dng RCD s gim nguy c

 in git.

1. Cn khi ng công tc

2. Nút khóa

3. Cn công tc o chiu

4. Khóa ngàm

5. Tr ngoài

6. Vòng

KiuMT605MT606MT607

Công sut

Thép 10 mm 10 mm 10 mm

G 25 mm 25 mm 25 mm

Tc  không ti (phút

-1

) 3.000 0 - 3.000 0 - 3.000

Chiu dài tng th 229 mm 229 mm 234 mm

Trng lng tnh 1,3 kg 1,3 kg 1,3 kg

Cp  an toàn /II

10. Chúng tôi luôn khuyên bn s dng ngun cp

in qua thit b RCD có th ngt dòng in d

nh mc 30 mA hoc thp hn.

An toàn cá nhân

11. Luôn tnh táo, quan sát nhng vic bn ang làm

và s dng nhng phán oán theo kinh nghim

khi vn hành dng c máy. Không s dng dng

c máy khi bn ang mt mi hoc chu nh

hng ca ma tuý, r

u hay thuc. Ch mt

khonh khc không tp trung khi ang vn hành dng

c máy cng có th dn n thng tích cá nhân

nghiêm trng.

12. S dng thit b bo h cá nhân. Luôn eo thit b

bo v mt. Các thit b bo h nh mt n chng

bi, giày an toàn chng trt, m bo h hay thit b

bo v

 thính giác c s dng trong các iu kin

thích hp s giúp gim thng tích cá nhân.

13. Tránh vô tình khi ng dng c máy. m bo

công tc  v trí off (tt) trc khi ni ngun in

và/hoc b pin, cm hoc mang dng c máy. Vic

mang dng c máy khi ang t ngón tay  v trí công

tc hoc cp in cho dng c máy 

ang bt thng

d gây ra tai nn.

14. Tháo mi khoá hoc chìa vn iu chnh trc khi

bt dng c máy. Vic chìa vn hoc khoá vn còn

gn vào b phn quay ca dng c máy có th dn

n thng tích cá nhân.

15. Không vi quá cao. Luôn gi thng bng tt và có

ch  chân phù hp. iu này cho phép iu khin

dng c máy tt h

n trong nhng tình hung bt ng.

16.

n mc phù hp. Không mc qun áo rng hay

eo  trang sc. Gi tóc, qun áo và gng tay

tránh xa các b phn chuyn ng.

Qun áo rng,

 trang sc hay tóc dài có th mc vào các b phn

chuyn ng.

17. Nu các thit b c cung cp  kt ni các thit

b thu gom và hút bi, hãy m bo chúng c

kt ni và s dng hp lý. Vic s dng thit b thu

gom bi có th làm gim nhng mi nguy him liên

quan n bi.

S dng và bo qun dng c máy

18. Không dùng lc i vi dng c máy. S dng



úng dng c máy cho công vic ca bn. S

dng úng dng c máy s giúp thc hin công vic

tt hn và an toàn hn theo giá tr nh mc c

thit k ca dng c máy ó.

19. Không s dng dng c máy nu công tc không

bt và tt c dng c máy ó. Mi dng c máy

không th iu khi

n c bng công tc u rt

nguy him và cn c sa cha.

20. Rút phích cm ra khi ngun in và/hoc ngt

kt ni b pin khi dng c máy trc khi thc

hin bt k công vic iu chnh, thay i ph

tùng hay ct gi dng c máy nào. Nhng bin

pháp an toàn phòng nga này s gim nguy c vô

tình khi 

ng vô tình dng c máy.

21. Ct gi các dng c máy không s dng ngoài

tm vi ca tr em và không cho bt k ngi nào

không có hiu bit v dng c máy hoc các

hng dn này vn hành dng c máy. Dng c

máy s rt nguy him nu c s dng bi nhng

ngi dùng cha qua ào to.

22. Bo qun dng c máy. Ki

m tra tình trng lch

trc hoc bó kp ca các b phn chuyn ng,

hin tng nt v ca các b phn và mi tình

trng khác mà có th nh hng n hot ng

ca dng c máy. Nu có hng hóc, hãy sa cha

dng c máy trc khi s dng. Nhiu tai nn xy

ra là do không bo qun tt dng c máy.

23. Luôn gi

 cho dng c ct c sc bén và sch

s. Nhng dng c ct c bo qun tt có mép ct

sc s ít b kt hn và d iu khin hn.

24. S dng dng c máy, ph tùng và u dng c

ct, v.v... theo các hng dn này, có tính n iu

kin làm vic và công vic c thc hin.

Vic s

dng dng c máy cho các công vic khác vi công

vic d nh có th gây nguy him.

Bo dng

25.  nhân viên sa cha  trình  bo dng

dng c máy ca bn và ch s dng các b phn

thay th ng nht. Vic này s m bo duy trì

c  an toàn ca dng c máy.

26. Tuân theo hng dn dành cho vic bôi tr

n và

thay ph tùng.

27. Gi tay cm khô, sch, không dính du và m.

GEB001-6

CNH BÁO AN TOÀN DÀNH CHO

MÁY KHOAN

1. S dng (các) tay cm ph, nu c cung cp

cùng vi dng c. Vic mt kh nng kim soát có

th dn n thng tích cá nhân.

2. Cm dng c máy bng b mt kp cách in khi

thc hin mt thao tác trong ó b phn ct có th

tip xúc vi dây dn kín hoc dây ca chính nó. B

phn ct tip xúc v

i dây dn “có in” có th khin

các b phn kim loi b h ca dng c máy “có in”

và làm cho ngi vn hành b in git.

3. Luôn m bo bn có ch t chân vng chc.

m bo rng không có ai  bên di khi s dng

dng c  trên cao.

4. Cm chc dng c.

5. Gi tay tránh xa các b phn quay.

6. Không  mc dng c hot ng. Ch vn hành

dng c khi cm trên tay.

7. Không chm vào mi khoan hay vt gia công ngay

sau khi vn hành; chúng có th rt nóng và gây

bng da.

8. Mt s vt liu có th cha hoá cht c. Hãy cn

thn  tránh hít phi bi và tip xúc vi da. Tuân

theo d liu an toàn ca nhà cung cp vt liu.

LU GI CÁC HNG DN NÀY.

CNH BÁO:

KHÔNG c  s thoi mái hay quen thuc vi sn

phm (có c do s dng nhiu ln) thay th vic

tuân th nghiêm ngt các quy nh v an toàn dành

cho sn phm này. VIC DÙNG SAI hoc không tuân

theo các quy nh v an toàn c nêu trong tài liu

hng dn này có th dn n thng tích cá nhân

nghiêm trng.

MÔ T CHC NNG

CN TRNG:

•Phi luôn m bo rng dng c ã c tt in và

ngt kt ni trc khi chnh sa hoc kim tra chc

nng ca dng c.

Hot ng công tc (Hình 1)

CN TRNG:

•Trc khi cm in vào dng c, luôn luôn kim tra

xem cn khi ng công tc có hot ng bình thng

hay không và tr v v trí “OFF” (TT) khi nh ra.

i vi kiu MT605

 khi ng dng c, ch cn kéo cn khi ng công

tc. Nh cn khi ng công tc ra  dng.

 tip tc vn hành, hãy kéo cn khi

ng công tc và

sau ó nhn vào nút khóa.

 dng dng c t v trí ã khóa, hãy kéo cn khi ng

công tc ht mc, sau ó nh ra.

i vi MT606, MT607

 khi ng dng c, ch cn kéo cn khi ng công

tc. Tc  dng c c gim xung bng cách tng lc

ép lên cn khi ng công tc. Nh cn khi 

ng công tc

ra  dng.

 tip tc vn hành, hãy kéo cn khi ng công tc và

sau ó nhn vào nút khóa.

 dng dng c t v trí ã khóa, hãy kéo cn khi ng

công tc ht mc, sau ó nh ra.

Thao tác công tc o chiu

i vi kiu MT606, MT607 (Hình 2)

Dng c này có mt công tc o chiu  thay i chiu

xoay. Di chuyn cn gt o chiu sang v trí  (mt A)

 xoay theo chiu kim ng h hoc v trí  (mt B) 

xoay ngc chiu kim ng h.

CN TRNG:

•Luôn luôn kim tra hng xoay trc khi vn hành.

•Ch s dng công tc o chiu sau khi dng c 

dng hoàn toàn. Vic thay i hng xoay trc khi

dng c dng có th làm hng dng c.

LP RÁP

CN TRNG:

•Luôn luôn m bo rng dng c ã c tt và tháo

phích cm trc khi dùng dng c thc hin bt c

công vic nào.

Lp hoc tháo g mi khoan

CN TRNG:

•Luôn m bo rng dng c này  c tt và rút

phích cm trc khi lp hoc tháo g mi khoan.

i vi kiu MT605, MT606 (Hình 3)

 lp t u mi, t nó vào trong ngàm kp ht mc

có th. Vn phn ngàm kp li bng tay. t khóa ngàm

vào mt trong ba l nh ri vn cht theo chiu kim ng

h. m bo vn ch

t c ba l ngàm u nhau.

 tháo mi khoan, hãy xoay khóa ngàm ngc chiu

kim ng h ch  mt l, sau ó vn lng b phn ngàm

bng tay.

i vi kiu MT607 (Hình 4)

Gi vòng và xoay tr ngoài ngc chiu kim ng h 

m ming ngàm. t u mi vào trong ngàm kp ht

mc có th. Gi cht vòng và xoay tr ngoài theo chiu

kim ng h  vn cht ngàm.

 tháo mi khoan, gi vòng và xoay tr ngoài ngc

chiu kim ng h.

VN HÀNH

Cm gi dng c

Ch gi dng c bng tay cm khi thc hin thao tác.

Thao tác khoan

Khoan vào g

Khi khoan vào g,  có kt qu tt nht cn s dng các

mi khoan dùng  khoan g và vít dn. Vít dn giúp

khoan d dàng hn bng cách kéo u mi vào trong vt

gia công.

Khoan vào kim loi

 phòng nga u mi b trt ra lúc bt u khoan l,

hãy to mt vt lõm bng cách dùng dùi c tâm và óng

vào im cn khoan. t u mi khoan vào ch lõm này

và bt u khoan.

S d

ng du nhn  ct khi khoan kim loi. Tr các

trng hp dùng st và ng thau cn phi c khoan

khô.

CN TRNG:

•Nhn dng c quá mc s không tng tc  khoan lên

c. Trên thc t, vic nhn mnh thêm này s ch

làm gây hng u mi ca bn, gim hiu nng và tui

th hot ng ca dng c.

•S có l

c quán tính rt ln trên dng c/mi khoan lúc

l khoan c xuyên thng. Gi cht dng c và

chun b ghìm lc quán tính li khi mi khoan xuyên

thng vt gia công.

•Luôn luôn gi cht các vt gia công có kích thc nh

bng kìm hoc dng c kp tng t.

BO TRÌ

CN TRNG:

•Luôn luôn m bo rng dng c ã c tt và tháo

phích cm trc khi dùng dng c thc hin bt c

công vic nào.

•Không bao gi dùng xng, ét xng, dung môi, cn

hoc hóa cht tng t. Có th xy ra hin tng mt

màu, bin dng hoc nt v.

 m bo AN TOÀN và TIN CY ca sn phm, vic

sa ch

a hoc bt c thao tác bo trì, iu chnh nào u

phi c thc hin bi các Trung tâm Dch v c y

quyn ca Makita (Makita Authorized Service Center),

luôn s dng các ph tùng thit b thay th ca Makita.



 



•   



   

• 

•  EPTA 01/2003

END201-5





 

.....

..................

ENE032-1



  

ENF002-2

 

 

   

 

GEA005-3

 



!  



 /  





 “”     ( ) 

   (  )  



 

1.  



2.   



  

  

   



 

 

4.   

  



   

 

5.       

     

  

6.  

   

 

7.          

  

    

 

1. 

2. 

 

4. 

5. 

6. 

 MT605 MT606 MT607





 10 .10 .10 .

 25 .25 .25 .

 ()3,000 0 - 3,000 0 - 3,000

   229 .229 .234 .

 1.3 .1.3 .1.3 .

 /II

8.   

   

  

9.    

 (RCD)  RCD  



10.   RCD  

 30 mA 

 

11.  

  

  

 

     

 

 

12.   

 

      

  



13.    

  / 

   



 

 

14.  

  



15.     

 



16.     

     

   

 

17.   



 

  



18.   

 

 



19.   



  



20.   /

   

  

   

21. 

  

  

   



22.  



 

  

   

 

 

23.  

 

 

 

24.     

 

 





25. 



   



26.

 

27.   

GEB001-6

 

1.    



2. 

   

  “” 

  “

”

 

3.  

   

4. 

5.  

6.     

 

7. 







8.    

 

 



:

   (

 )  

    

 

 

 

:

•   



 ( 1)

:

•   

    “OFF” 

 MT605

     

  

 



 

 MT606, MT607

  

   

  

 



 

 

 MT606, MT607 ( 2)

    

   ( A) 

   ( B) 

:

• 

•   

 

   



:

•   

 



:

•  



 MT605, MT606 ( 3)

  

     





  

    

 MT607 ( 4)

   

  



   











  

    



   

      

  

 

:

• 

  

   

 

• /  

 

•      





:

•   

 

•      

     

  

 

 Makita   

  Makita 

Makita Corporation

Anjo, Aichi, Japan

885030A377 www.makita.com

TRD

Makita MT605 User manual

Brand: Makita

Model: MT605

Category: Power tools

Type: User manual

This manual is also suitable for

MT606
MT607

Download PDF

report

in other languages

slovenčina: Makita MT605 Používateľská príručka

Makita MT605 User manual

This manual is also suitable for

Makita MT605 User manual

in other languages

Related papers

Other documents