BA SC18-28X1pro,44X1pro N;GB,DK,NO,FIN -22421- 2009.04-03
*OPTIONAL
Instruction Manual
GB
Time switch
Connection diagram 1. Safety instructions 2. Initial operation
1 channel
2 channels
1 channel
2 channels
!
The installation and assembly of electrical equipment
must be only carried out only by a skilled Person!
Otherwise fire danger or danger of an electric shock
exists!
!
Connect the supply voltage/frequency as stated on the
product label!
!
Warranty void if housing opened by unauthorised
person!
!
The electronic circuit is protected against a wide range
of external influences. Incorrect operating may occur if
external influences exceed certain limits!
The time switch is delivered in sleep-mode, the display is switched off.
Press -button for 1 second.
The current date and time is already programmed and European daylight
savings time is activated.
Select the desired language by pressing -buttons and confirm it by
pressing
. (Remark: By pressing you move one step backwards from
the current position)
If required, date, time and daylight savings time mode can be adjusted also
by pressing
-buttons and a subsequent confirmation with .
3. Menu overview 4. Symbol legend
Channel is switched ON
Channel is switched OFF
For the current date the “holiday program” / “permanent by date” is activated
Standard programming step
Current state is based on a manual over-ride. The state will be cancelled with the next programming step.
Current state is based on a manual over-ride. The state is permanent until terminated manually (7).
Days of the week Monday, Tuesday, ... Sunday;
The underscores indicate if the program is active for the days above.
I
Current state is based on a switching time with pulse function
Element within sub-menu “program delete”
The time switch is locked; to unlock the device the PIN has to be entered (12).
5. Key function 6. Handling advice 7. Channel ON OFF / Permanent P
1. To access the Enter-mode (program, adjustments, options) from the automatic-mode.
2. To revert to the beginning of the current (sub-) menu.
1. To adjust the flashing digit.
2. To scroll through a choice
1. Automatic-mode: To switch the channel ON or OFF until the next programming step occurs.
2. Automatic-mode: A push longer than 3 sec. = Permanent switching status (7).
1. To activate the time switch when operated without power supply.
2. To confirm the selection or the entered data.
The time switch is programmable without external power supply after
pressing the
-button.
To revert one step or one level back while in the Enter-Mode press .
After completion of a (sub-) menu confirming end will return the device
into the automatic-mode.
With the choice changes from end to continue. By confirming
continue the time switch returns to the beginning of the current
(sub-) menu.
When confirming end before completion, the time switch returns to the
automatic-mode without saving the entered data.
Channel
ON OFF
By pushing
-buttons ( -buttons) a manual switch of the
channels take place. The resulting switching status is marked
with the hand-symbol and remains until the next programming
step occurs. (temporary over-ride)
Permanent switching status P
By pressing the corresponding channel button for more
than 3 sec. the channel is permanently switched ON or OFF.
The status remains until the next manual switching occurs (> 3
sec.). (permanent over-ride)
8. New Program (See also the example (9)) 9. Example „New Program“ (For a regular switching time)
Step A. to C. please refer to point 9. (Example “New Program”)
A. If power supply is disconnected press
for one second. The display appears in Automatic-Mode.
B. Press
, the time switch is now in the Enter-Mode.
C. Confirm
Program with .
D. Confirm
new program with .
E. Choose the desired channel with
and confirm with .
F. For regular switching times choose
on or off with -buttons and confirm with .
G. Within this level you activate the days of the week (1…7) on which the switching time should happen.
With
you activate “yes” or deactivate “no” the corresponding date. Confirm each day with .
H. Adjustment of the time: Hours
and . Minutes and .
I. Verify the entered switching time: If the flashing summary of the programming step is correct, verify
on
or off with
. After verification you have the choice between edit/delete and end with .
J. If you want to proceed with programming, confirm
next switching with .
To leave the programming menu confirm
end.
10. Pulse 11. Program permanent
Program -> New program -> Channel A/B -> …
The pulse function provides you the opportunity of programming a switching time with a defined duration.
As soon as the pulse-duration has expired the time switch switches OFF automatically (the duration of the pulse is up to 59:59 mm:ss).
The programming is carried out like a standard switching time (see point 8 / 9) with following differences
Choose Pulse function (9F).
Define the duration of the pulse (pulstime minute / pulstime second).
Program the days of the week
Program the switching time (time hour / time minute)
Validation: Confirm the blinking summary of the pulse program
Program -> new program -> channel A/B -> permanent -> …
One permanent by date programming step (holiday function) for each channel is possible. During the
desired period (The function is valid for the whole days) the channel can be switched off (
permanent
off
) or on (permanent on).
The programming of this function is as described in (8 / 9).
The choice permanent will not be offered anymore within the menu new program when already in
use. The switching time can be modified and deleted within
Program modify (13) and Program
delete
(12) respectively.
12. Additional adjustments 13. Program modify
Menu Main menu Application
Program query
Program
To query the programming steps and remaining memory locations
Program copy
Program
Copy from one channel to another. Memory of the channel won’t
be overwritten; the copied switching steps appear additionally.
!
Permanent by date function is not copied!
Program delete
Program
Deletion of switching time(s). The program for all channels, single
channels and single programming steps within on channel can be
deleted.
Date-Time
Adjustment
Adjustment of date and time
Summertime
Adjustment
Adjustment of the daylight saving time mode (ON/OFF)
Language
Adjustment
Choice of languages
Program -> Program modify -> …
Within Program modify each single switching time can be modified.
Factory Defaults*
Adjustment
Reset to the state of delivery.
!
Date, time and switching program will be lost!
14. Data-key*
Counter
Options
Displays the hour counter and pulse counter for each channel and
the time switch itself.
PIN-Code
Options
The time switch can be locked with a 4-digit PIN-Code. The code
can be adjusted, activated and deactivated. If you have forgotten
the Code please call customer service.
Reset-Function
Press all front keys for 2 seconds. The time switch is reset. The values for date
and time will be deleted and have to be re-entered. The switching program has
not been deleted!
With a Data-key following activities are possible:
Save data: Writes the data from the time switch into the memory of the Data-key.
Program timeswitch: Writes the data located inside the Key into the memory.
Key function: The time switch will solely apply programming steps from the Data-
key. The switching program of the time switch is suppressed.
Key readout: To query the switching program of the Data-key.
- 72112 (1 channel) / 72212 (2 channel)
Sangamo Limited
Industrial Estate, Port Glasgow,
Renfrewshire, PA14 5XG
Tel: 01475 745131 Fax: 01475 600370
Email: [email protected]
Web: www.sangamo.co.uk 72112/72212 Issue A
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
ABB DY365 4CE User manual
-
-
JUNG 2154REG Operating instructions
-
AMX NX-4200 User guide
-
Meinberg LANTIME M600/MRS/PTP User manual
-
Hager EGN200AU User manual
-
-
-
-
Meinberg LANTIME M600 User manual