Bell 5029-0 Installation guide

Bell
Brand
Bell
Model
5029-0
Type
Installation guide

Bell 5029-0 is a single-gang device cover designed to protect electrical devices in wet locations. It is made of durable materials and is easy to install. The cover is listed 731A by UL for use in wet locations with the cover closed. It is also suitable for use in flush device covers. Some possible use cases for the Bell 5029-0 include:

  • Protecting electrical outlets in bathrooms, kitchens, and other wet areas
  • Covering electrical devices in outdoor areas, such as decks and patios
  • Protecting electrical devices in industrial settings, such as factories and warehouses

Bell 5029-0 is a single-gang device cover designed to protect electrical devices in wet locations. It is made of durable materials and is easy to install. The cover is listed 731A by UL for use in wet locations with the cover closed. It is also suitable for use in flush device covers. Some possible use cases for the Bell 5029-0 include:

  • Protecting electrical outlets in bathrooms, kitchens, and other wet areas
  • Covering electrical devices in outdoor areas, such as decks and patios
  • Protecting electrical devices in industrial settings, such as factories and warehouses
5029-0
07
50169 50290
RAYNTITE
®
SINGLE-GANG DEVICE COVER
Cubierta de Perforación
Sencilla Rayntite
Couvercle pour Boîte
Simple Rayntite
®
®
GENERAL INSTRUCTIONS
IMPORTANT: Mount cover with hinge
on top.
1. Turn off power.
2. Use only copper wire.
3. Remove appropriate device cutout on
gasket.
4. Center cover gasket evenly.
5. Install mounting screws (provided).
6. Use caulking around cover if not
mounted to a U.L. listed wet locations
box.
7. Installation and wiring must comply
with local electrical codes.
NOTE: If mounting to box, drill out
(4) 5/32” holes in drill spots on plate
before assembly.
One Single Receptacle 1.710”
Una Tomacorriente Unica
de 1.710”
Une Prise Simple 1.710po
INSTRUCCIONES GENERALES
IMPORTANTE: Fijar la tapa con la bisagra
hacia arriba.
1. Cortar la corriente eléctrica.
2. Usar solamente cable de cobre.
3. Quitar de la junta el recorte que corresponda al
dispositivo.
4. Centrar bien la junta en la tapa.
5. Instalar los tornillos de fijación (provistos).
6. Aplicar un sellador alrededor de la tapa si no está
fijada a una caja homologada por U.L. para lugares
mojados.
7. La instalació n y el cableado deben ajustarse a los
códigos eléctricos locales.
NOTA: Si se monta en una caja, perforar (4) orificios
de 4mm sobre los puntos marcados en la placa antes
del montaje.
REMARQUE- Si le montage se fait sur une boîte, percer
(4) ouvertures de 4 mm dans la plaque avant le montage.
Percer aux endroits indiqués sur la plaque.
HUBBELL ELECTRICAL PRODUCTS
DIVISION OF HUBBELL INCORPORATED (DELAWARE)
P.O. BOX 4002 SOUTH BEND INDIANA 46634
CANADA 870 BROCK RD. S. PICKERING, ON L1W 1Z8
MADE IN INDIA / HECHO EN INDIA / FAIT AU INDIA
LISTED 731A
FLUSH DEVICE COVER
WITH COVER CLOSED
LISTADA 731A
TAPA PARA
DISPOSITIVO AL RAS
SITIOS MOJADOS CON
LA TAPA CERRADA
ENREGISTRER 731A
COUVERCLE DE
DISPOSITIF AFFLEURANT
ENDROITS MOUILLÉS SI
LE COUVERCLE EST FERMÉ
WET LOCATIONS
DIRECTIVES GÉNÉRALES
IMPORTANT: Monter le couvercle avec la charniére sur
le dessus.
1. Couper le circuit d’alimentation
2. Utiliser uniquement du fil de cuivre.
3.Enlever la découpe appropriée au dispositif sur la
garniture du joint d’ étanchéité.
4. Centrer convenablement la garniture de joint
du couvercle.
5. Monter les vis de fixation (fournies).
6. Placer du calfeutrage autour du couvercle si
celui-ci n’est pas monté sur une boîte homologuée U.L.
pour les endroits mouillés.
7. Le montage et le câblage doivent être conformes
aux codes d’ électricité locaux.
  • Page 1 1

Bell 5029-0 Installation guide

Bell
Brand
Bell
Model
5029-0
Type
Installation guide

Bell 5029-0 is a single-gang device cover designed to protect electrical devices in wet locations. It is made of durable materials and is easy to install. The cover is listed 731A by UL for use in wet locations with the cover closed. It is also suitable for use in flush device covers. Some possible use cases for the Bell 5029-0 include:

  • Protecting electrical outlets in bathrooms, kitchens, and other wet areas
  • Covering electrical devices in outdoor areas, such as decks and patios
  • Protecting electrical devices in industrial settings, such as factories and warehouses
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents