CAMBRIDGE CAM6022-1CHR User manual

MANTEL

MODEL

X6022-1TEK

X6022-1MAH

X6022-1BLK

X6022-1GRY

X6022-1CHR

X6022-1WHT

X6022-1WAL

REV19-01

3

PACKAGE CONTENTS

Carefully remove all pieces from the carton and make sure that you have all parts listed

(refer to parts list on page 2-3).

6'8: *+9)8/6:/54 7:? 6'8:45

A Top Panel 1

B Left Side Panel 1

C Right Side Panel 1

D Top Shelf Divider 1

E Shelf Rail 1

F

1

Right

Trim Panel 1

F

2

Left

Trim Panel 1

G

1

Right

Inner Panel 1

G

2

Left

Inner Panel 1

HBase 1

I Base Back Panel 1

J Base Left Panel 1

K Base Right Panel 1

L

Base

Left

Support

1

M

Base Right Support

1

N Base Middle Support 1

O Top Shelf 1

P Upper Back Panel 1

Q

1 Lower Back Panel 1

Q

2 Lower Back Panel 1

R

1 Adjustable Shelf

f

1

R

2

Adjustable Shel 1

S Base Middle Panel 1

T Left Door 1

U Right Door 1

AA Bolt 61

BB Metal Connector 61

CC Shelf Pin 8

DD SPanel crew 24

EE Cabinet Door Hinge 4

FF Handle 2

GG Screw M4X18 2

SS

1

Safety Chain

4

PACKAGE STEPS

1.

2.

AA

[

M

N

L

M

N

L

X6

J

S

K

5

PACKAGE STEPS

3.

4.

AA

X2

[





[

;

AA

I

M

N

BB

L

X6

[

I

6

PACKAGE STEPS

5.

6.

BB

X16

AA

7

PACKAGE STEPS

7.

8.

H

BB

X16

AA

X8

8

PACKAGE STEPS

9.

10.

9

PACKAGE STEPS

11.

12.

G2

AA

X3

AA

G1

G

F1

F2

2

10

PACKAGE STEPS

13.

14.

BB

X3

CC

X4

BB

X3

G1

G2

11

PACKAGE STEPS

15.

16.

BB

X4

Q1

Q2

AA

X7

12

PACKAGE STEPS

17.

18.

O

BB

X3

E

13

PACKAGE STEPS

19.

20.

O

BB

X2

BB

X2

14

PACKAGE STEPS

21.

22.

X2

B

C

CC

X2

AA

X2

AA

X2

CC

15

PACKAGE STEPS

23.

24.

D

X4

BB

X4

BB

X2

BB

X2

AA

X6

A

P

16

PACKAGE STEPS

25.

26.

A

BB

X6

17

PACKAGE STEPS

27.

28.

R1

R2

18

PACKAGE STEPS

29.

30.

T

EE

X2

FF

GG

DD

X4

U

EE

X2

FF

GG

DD

X4

X8

DD

19

PACKAGE STEPS

31.

32.

X8

DD

T

U

20

PACKAGE STEPS

IMPORTANT - Safety Chain Installation

WARNING:

INSTALLATION:

This mantel is heavy furniture. Please be sure to correctly attach the safety chain to both the mantel and an adjacent wall.

Failure to do so can cause serious injury or death.

Assemble the mantel and place it in position

Attach one end of the chain to a wall stud using the screw included

Attach the other screw – through a link in the chain – to the center of the mantel’s top board (you may need to drill a small

starter hole). Put the screw through the chain link that allows the least amount of slack in the chain.

Carefully test that the installed chain adequately prevents tipping or tilting of the mantel.

NOTE: The chain must be as short as possible to prevent the mantel tipping forward. Do not allow slack in the chain.

CAMBRIDGE CAM6022-1CHR User manual

CAMBRIDGE CAM6022-1CHR User manual

Related papers

Other documents